CAUTION!
PLEASE KEEP POWER
SWITCH ON BEFORE
OPERATING THIS EQUIPMENT
Turbo Air Speed up the Pace of Innovation
Refrigerator
Freezer
Installation and Operation Manual
Please read this manual completely before attempting to install or operate this equipment!
SOLID DOOR
REFRIGERATOR
MSR-23NM
MSR-49NM
SOLID DOOR
FREEZER
MSF-23NM
MSF-49NM
GLASS DOOR
REFRIGERATOR
MSR-23G-1
MSR-49G-2
MSR-72G-3
www.turboairinc.com
CONTENTS |
|
|
|
|
PAGE |
1. |
SPECIFICATION.......................................................................................... 2 |
|
2. |
SERIAL NUMBER ........................................................................................ 2 |
|
3. INSTALLATION............................................................................................ |
3 |
|
4. |
CLEANING ................................................................................................... 4 |
|
5. BASIC OPERATION |
|
|
|
5-1. REFRIGERATORS........................................................................... |
5~8 |
|
5-2. FREEZERS..................................................................................... |
9~12 |
6. BEFORE REQUESTING SERVICE ........................................................... 13 |
||
7. |
WARRANTY......................................................................................... 14~15 |
|
SPECIFICATION
Refrigerators
MODEL |
COMP H.P. |
V/Hz |
REFRIGERANT |
AMPS |
WEIGHT |
MSR-23NM |
1/3 |
115V/60Hz |
R-134a |
5.5A |
259lbs |
|
|
|
|
|
|
MSR-49NM |
1/3 |
115V/60Hz |
R-134a |
9.2A |
412lbs |
MSR-23G-1 |
1/3 |
115V/60Hz |
R-134a |
5.5A |
274lbs |
MSR-49G-2 |
1/3 |
115V/60Hz |
R-134a |
9.2A |
427lbs |
|
|
|
|
|
|
MSR-72G-3 |
2/3 |
115V/60Hz |
R-134a |
9.6A |
610bls |
|
|
|
|
|
|
Freezers
MODEL |
COMP H.P. |
V/Hz |
REFRIGERANT |
AMPS |
WEIGHT |
MSF-23NM |
1/2 |
115V/60Hz |
R-404A |
8.7A |
285lbs |
MSF-49NM |
3/4 |
115V/60Hz |
R-404A |
10.5A |
462lbs |
SERIAL NUMBER
The serial number is located on the data label inside.
Please retain the unitʼs serial number for service purpose.
2
INSTALLATION
1. GOOD AIR CIRCULATION
-Be sure to avoid any partition and object which may stop the air flow.
-Be sure that air space is allowed to flow the rear of the unit.
Turbo air recommends that the rear of the unit would be no less than 5 inches from the wall.
2. PLACE ON STRONG GROUND
- Be sure that the location be chosen has a strong enough floor to support the total weight of the cabinet and any other contents.
3. DO NOT PLACE NEAR HEAT
- Be sure to avoid hot corners and locations near stoves.
- High ambient temperature will make much lower cooling efficiency.
4. INDOOR USAGE ONLY
- Be sure to install this unit indoor.
- So, It should prohibit getting wet from the rain.
5. STABILIZING
- Make sure the unit is installed in a stable condition with the front wheels locked while in use.
6. LEVELING
- Be sure that the unit levels from the front to the back and side to side.
7.Unit should be on dedicated outlet.
8.Place black plastic condensate pan through back or front. Make sure pads are installed upwards, a drain hose is in pan.
3
CLEANING
1.CLEANING STAINLESS STEEL INTERIOR AND EXTERIOR (select models)
:Damage to stainless steel finish due to improper use of cleaning products or nonrecommended products is NOT covered under this product's warranty.
•DO NOT USE
- Abrasive or harsh cleaners
- Ammonia
- Chlorine bleach
- Concentrated detergents or solvents
- Metal or plastic-textured scouring pads - Vinegar-based products
- Citrus-based cleaners
•Do
- Use warm, soapy water and a soft, clean cloth or sponge.
- Rinse surfaces with clean, warm water and dry immediately to avoid water spots.
2.CLEANING THE CONDENSER FINS
-To maintain proper refrigeration performance, the Condenser coil must be free of dust, dirt, and grease.
This will require periodic cleaning. Condenser fins should be cleaned at least every three months (90 days) or as needed.
3.CLEAN THE GASKET
-The door gasket should be cleaned frequently to maintain proper sealing.
4.CHECK AFTER CLEANING
-Check the unit again for safety.
-Check that the unit is operating properly.
CAUTION
1.POWER CORD
-Be sure that the power cord is connected to the proper voltage.
-A protected circuit of the correct voltage and amperage must be run for connection of the line cord.
-Turn ʻoffʼ the power switch before disconnecting the power cord, whenever performing maintenance functions or cleaning the refrigerated cabinet.
-Compressor warranties are void if compressor burns out due to low voltage.
2.RE-STARTING
-If disconnected, wait for 5 minutes before re-starting.
4
BASIC OPERATION
REFRIGERATORS |
MSR-23NM MSR-23G-1 |
|
MSR-49NM MSR-49G-2 |
||
|
||
|
MSR-72G-3 |
1.Plug in and turn on the power switch located on the bottom of the top grille right side.
The Display panel will be lighted and make a beep sound. The compressor will begin to run.
2.The default temperature setting is No. “5”.
3.The compressor is automatically cycled by the electronic controller (PCB, D-Sensor).
4.The Defrost cycle is automatically controlled by the R-sensor, and the PCB.
5.Set level toward “1” for higher temperature and toward “9” for lower temperature.
6.The interior light is activated by the rocker switch at the bottom of the grille when the door is opened. (MSR-23NM,MSR-49NM)
7.Evaporator fan motor(s) will run after all doors are completely closed.
5
Loading...