Triton T20ID Operating And Safety Instructions Manual

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated rubber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated

area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Certaines poussières générées par le ponçage, sciage, le perçage et d’autres activités de constructions électriques contiennent des substances chimiques
reconnues dans l’État de la Californie comme étant une cause de cancer, de malformations congénitales et d’autres problèmes reproductifs. Des exemples de ces
substances chimiques sont :

• Le plomb, provenant des peintures à base de plomb

• La silice cristalline, provenant des briques, du ciment et d’autre matériaux de construction

• L’arsenic et le chrome, provenant des caoutchoucs traités chimiquement
Les risques résultant de ces expositions varient en fonction de la fréquence à laquelle vous effectuez ce type de travaux. Pour réduire l’exposition à ces substances

chimiques : travaillez dans une zone ventilée et portez un équipement adapté, comme un masque à poussière conçu spécialement pour filtrer les particules
microscopiques.

Parte del polvo creado por el lijado, aserrado, esmerilado, taladrado y otras actividades de construcción contienen sustancias químicas identificadas por el estado
de California como causantes de cáncer, o defectos de nacimientos, y/u otros daños reproductivos. Algunos ejemplos de estos productos químicos son:

• El plomo de las pinturas a base de plomo.

• La sílice cristalina de los ladrillos y cemento y otros productos de mampostería.

• El arsénico y el cromo de goma tratados químicamente.
El riesgo derivado de estas exposiciones puede variar dependiendo de la frecuencia con que se realice este tipo de trabajo. Para reducir la exposición a estas

sustancias químicas, trabaje siempre en áreas bien ventilada y lleve equipos de seguridad adecuados, tales como máscaras contra el polvo especialmente
diseñadas para filtrar partículas microscópicas.

869029_Z1MANPRO1.indd 2 26/09/2014 09:00

GB

Operating and
Safety Instructions

Instructions d’utilisation

F

et consignes de sécurité

Instrucciones de

ESP

uso y de seguridad

Instruções de

PT

Operação e Segurança

取扱説明書および安全の

JP

手引き

20V Impact Driver

T20 ID

tritontools.com

869029_Z1MANPRO1.indd 2 26/09/2014 09:00

GB

Original Instructions

Thank you for purchasing this Triton tool. This manual contains information necessary for safe and effective operation of this product. This
product has unique features and, even if you are familiar with similar products, it is necessary to read this manual carefully to ensure you

fully understand the instructions. Ensure all users of the tool read and fully understand this manual.

Contents

Specification 2
Product Familiarisation 3
Description of Symbols 4
General Safety 4
Additional Safety for Battery-Operated Screwdrivers 5
Battery Pack & Charger Safety 5
Intended Use 6
Unpacking Your Tool 6

Before Use 6
Operation 7
Accessories 7
Maintenance 7
Disposal 7
Troubleshooting 8
Guarantee 9

Specification

Model number: T20ID

Impact driver

Voltage: 20V, DC

No load speed: 0 - 2400min

Impact frequency: 3300min

Speed control: Trigger

Maximum torque: 160Nm / 118 ft lb

Drive:

Weight: 1.59kg / 3.51lbs

Sound and vibration information:

Sound pressure LPA: 93.8dB(A)

Sound power LWA: 104.8dB(A)

Uncertainty K: 3dB

Weighted vibration ah: 17.564m/s

Uncertainty K: 1.5m/s

The sound intensity level for the operator may exceed 85dB(A) and sound
protection measures are necessary.

WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit the time of exposure if necessary. If sound levels are uncomfortable, even
with ear protection, stop using the tool immediately and check the ear protection is correctly fitted and provides the correct level of sound attenuation for the level
of sound produced by your tool.

WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness, tingling and reduced ability to grip. Long term exposure can lead to
a chronic condition. If necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool with hands below a normal
comfortable temperature, as vibration will have a greater effect. Use the figures provided in the specification relating to vibration to calculate the duration and
frequency of operating the tool.

Sound and vibration levels in the specification are determined according to EN60745 or similar international standards. The figures represent normal use for the tool
in normal working conditions. A poorly maintained, incorrectly assembled, or misused tool, may produce increased levels of noise and vibration. www.osha.europa.
eu provides information on sound and vibration levels in the workplace that may be useful to domestic users who use tools for long periods of time.

-1

-1

1

⁄4" / 6.35mm hex drive

2

2

Battery

Technology: Samsung Li-Ion cells

Model & capacity: T20HCB, 4.0Ah

T20B, 2.0Ah

Battery charger

Charger model: T20BC

Charging times: 1hr (T20HCB)

Input Voltage: EU: 220-240V, AC 50/60Hz, 80W

Power output: 20V, DC, 3.0A

Length of power cord: 2m

As part of our ongoing product development, specifications of Triton
products may alter without notice.

30min (T20B)

SA: 220-240V, AC 50/60Hz, 80W
AU: 220-240V, AC 50/60Hz, 80W
JP: 100V, AC 50/60Hz, 1.3A
US/CAN: 120V, AC 60Hz, 1.3A

2

869029_Z1MANPRO1.indd 2 26/09/2014 09:00

GB

Product Familiarisation

1. 1⁄4" / 6.35mm Hex Drive

2. Forward/Reverse Switch

3. Speed Control Trigger Switch

4. Battery Release Button

5. Belt Clip

6. Battery *

7. LED Guide Light

8. T20 Battery Charger

Accessories (not shown):

• Soft carry case

1

Converter Plug

UK users: do not attempt to remove the installed UK converter plug and use it
on other appliances.

Do not remove the installed UK converter plug and attempt to insert it directly
into UK mains power supply sockets.

If the UK converter plug is damaged, please contact an authorised Triton
service centre.

7

8

NOTE: Battery provided may differ from image.

2

3

4

5

6

3

869029_Z1MANPRO1.indd 3 26/09/2014 09:00

GB

Description of Symbols

Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection

Read instruction manual

Caution!

DO NOT incinerate batteries!

For indoors use only (battery and battery charger)!

Internal time-lag fuse with rated current 3.15A

T3.15A

Environmental Protection

Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.

Environmental Protection

Waste electrical products and batteries, including Li-Ion batteries,
should not be disposed of with household waste. Please recycle
where facilities exist. Check with your local authority or retailer for
recycling advice.

Li-ion battery cells are recyclable and should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice

Li-ion

Conforms to relevant legislation and safety standards. (Only EU model)

4

General Safety

WARNING Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

WARNING: This appliance is not intended for use by persons (including children)
with reduced, physical or mental capabilities or lack of experience or knowledge.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.

Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents
b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location is unavoidable, use a

residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

Personal safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce personal
injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power Tool Use & Care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must
be repaired.

c) Disconnect the plug from the power source and/or the battery pack

from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

869029_Z1MANPRO1.indd 4 26/09/2014 09:00

GB

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from

those intended could result in a hazardous situation.

Battery tools use and care

a) Recharge only with charger specified by the manufacturer. A charger

that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.

b) Use power tools only with specifically designated battery packs.

Use of any other battery packs may create a risk of injury and fire

c) When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws and other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause a burns or

a fire.

d) Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If
liquid contact eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

WARNING: When used in Australia or New Zealand, it is recommended that
this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.

Service

a) Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

Additional Safety for Battery­Operated Screwdrivers

For safety relating to protective clothing/equipment and general health hazards
relating to power tools; refer to General and Electrical Safety sections in this
manual

Important: It is imperative to follow all national safety regulations concerning
installation, operation and maintenance

• Do not allow anyone under the age of 18 years to use this tool, and ensure
that operators are qualified and familiar with the operating and safety
instructions

• If batteries are to be charged outdoors, ensure that the power supply and
charger are protected against weather/moisture

• Use metal and voltage detectors to locate concealed electric, water or gas
lines. Avoid touching live components or conductors

• Ensure that the lighting is adequate

• Do not put pressure on the tool, to do so would shorten its service life

• Where possible, use clamps or a vice to hold your work

• Examine the chuck regularly for signs of wear or damage. Have damaged
parts repaired by a qualified service centre

• Periodically check all nuts, bolts and other fixings and tighten where
necessary

• Hold power tools by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Fasteners contacting a “live” wire may make exposed metal parts of the
power tool “live” and give the operator an electric shock.

Battery and Charger Safety

Use the battery charger correctly

• Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery.

• Do not attempt to use the charger with any batteries other than those
supplied. Keep your battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these instructions may
cause overheating or fire

• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard

• Examine the battery charger regularly for damage, especially the cord, plug
and enclosure. If the battery charger is damaged, it must not be used until
it has been repaired

• Children should be supervised to ensure that they do not play with the
appliance

Warning: Do not recharge non-rechargeable batteries

Use batteries correctly

• Only charge batteries using the charger provided. Only use batteries
provided with this power tool, or others recommended by the supplier.
Keep batteries clean; foreign objects or dirt may cause a short. Allow
batteries to cool for 15 minutes after charging or heavy use. Failure to
follow these instructions may cause overheating or fire.

• When not in use batteries should be stored at room temperature (approx.
20˚C). Ensure that batteries cannot accidentally short in storage.

WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire, burn
and explosion hazard.

• Keep the battery out of reach of children

• Only charge Li-Ion batteries using the charger provided or designed
specifically for your product

• Only use Li-Ion batteries provided with a product or specifically designed to
be compatible

• Allow batteries to cool for 15 minutes after charging or heavy use. Failure
to follow these instructions may cause overheating or fire

• When not in use batteries should be stored at room temperature
(approximately 20˚C)

• Ensure that battery contacts cannot accidentally short in storage. Keep
batteries clean; foreign objects or dirt may cause a short. Keep away from
other metal objects, for example paperclips, coins, keys, nails and screws

• Under abusive conditions, liquid may be ejected from the battery. This
liquid may cause skin irritation or burns. Avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, seek medical
help

• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not
dispose of in fire or similar

Battery and charger safety features

The battery and charger are fitted with a number of safety features which may
be triggered during charging or operation:

• Over-charge protection: Charger automatically switches off when
the battery has reached full charge capacity, protecting the internal
components of the battery

• Over-discharge protection: Prevents the battery from discharging beyond
the recommended lowest safety voltage

• Over-heat protection: Sensor switches off if the battery becomes too
hot during operation. This can happen if the tool is overloaded or being
used for extended periods of time. Up to 30 minutes cooling time may be
required depending on the ambient temperature

• Overload protection: Battery temporarily stops if it is overloaded or the
maximum current draw is exceeded, protecting the internal components.
The battery will resume normal operation when the current draw returns to
a normal safe level. This may take a few seconds

• Short circuit protection: The battery will stop working immediately if a short
circuit occurs, this prevents damage to the battery or tool

5

869029_Z1MANPRO1.indd 5 26/09/2014 09:00

GB

Intended Use

• Battery operated impact driver suitable for medium duty tasks driving nuts
and bolts

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its
features and functions

• Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before attempting
to use this tool

Before Use

• This cordless impact driver has been shipped in a low charge condition.
Charge the battery before use

Battery charger operation

• The charger and battery may become warm while charging. This is normal
and does not indicate a problem

• Use the charger at normal room temperatures whenever possible. To
prevent overheating, do not cover the charger and do not charge the
battery in direct sunlight or near sources of heat

If the battery does not charge properly:

• Check current at power outlet by plugging in a lamp or other appliance

• If charging problems persist, have the impact driver, battery and battery
charger checked by an electrician or a power tool technician

Charging the battery

1. Depress the Battery Release Button (4) and remove the battery from the
tool

2. Insert the battery into the T20 Battery Charger (8). Do not use excessive
force when inserting the battery. If it does not slide into place easily, it is
not being inserted correctly

3. Initially only the green LED may flash as it evaluates the status of the
battery. When charging the red LED will illuminate and the green LED will
be OFF

4. When the battery is fully charged the red LED will be OFF and the green
LED will illuminate

5. The battery charger will constantly monitor the condition of the battery
when charging

6. Remove the battery as soon as possible when completely charged

7. Disconnect the charger from the power supply and store in a clean, dry
environment out of the reach of children. 2.0Ah battery: Please note the full
charging time will be approximately 30 minutes

• Normal battery charging time is approximately 1hour for a recently fully
discharged 4Ah battery at normal temperature. Charging times will vary
outside these conditions

• You do not need to fully discharge the battery before recharging but you
should not attempt to recharge a battery that is already fully charged

• You can interrupt charging at any point to use the battery. Under normal
conditions the charger charges at a higher rate but reduces the charging
rate as the battery becomes fully charged. An 80% charge is achieved after
1/2hr of charging

Battery charging table

Red LED Green LED

Charger plugged In OFF Flashing

Charger evaluating battery OFF Flashing

Fast charging ON Off

Highly discharged battery slow
charging

Abnormal battery temperature
charging

Fully Charged OFF On

Battery or charger fault Flashing Flashing

Temporary abnormal temperature
condition

Note: If the lights on the battery charger fail to illuminate according to the
chart above or indicate a fault condition:

• Check the battery is firmly seated in the battery charger

• Check all connections and that mains power is switched on

Flashing Off

Flashing Off

On On

Initial charge

• The initial charge will vary depending on the existing charge in the battery.
Allow the battery to reach full charge as indicated on the charger

• After discharging, recharge the battery completely, as indicated by the LED
on the battery charger, for the next 4 to 5 uses. This will ensure that the
battery is performing to its highest capacity

• Subsequent full charges will take approximately 1 hour (4Ah battery),
however the battery can be recharged when the battery is only partially
discharged

Re-charging the battery

• After use, a lithium-ion battery must be allowed to cool down before
charging

• If a hot battery is inserted into the charger both LEDs will illuminate. The
charger will begin to charge when the battery has cooled sufficiently (this
may take several minutes)

Installing the battery

• The battery should fit easily into the battery charger or drill unit. If the
battery is difficult to fit, check the condition of the battery and contacts

Battery - length of service

• The length of service from each charging cycle will depend on the type
of workload. The battery charger and battery for this impact driver have
been designed to provide a long trouble-free working life. The charger
intelligently monitors the condition of the battery and selects the ideal
charging rate for the condition of the battery. It protects the battery from
over-charging or charging at too high a rate. However, like all batteries,
performance will be reduced over time

To maximise battery life:

• Store and charge the battery in a cool area. Temperatures above or below
normal room temperature will reduce battery life

• Never store lithium-ion batteries in a discharged condition. Recharge them
immediately after they are discharged. For storing long term, store fully
charged

• All batteries gradually lose their charge, even lithium-ion batteries, but the
discharge rate is very low. If the impact driver is stored for long periods
of time without use, recharge the battery every three to four months and

6

869029_Z1MANPRO1.indd 6 26/09/2014 09:00

GB

disconnect the battery from the power tool before it is stored. This practice
will prevent the lithium-ion battery being damaged when stored

Fitting a driver bit

WARNING: DO NOT fit any attachment with a maximum speed lower than the

no load speed of the machine.

1. Pull the quick release mechanism of the Hex Drive (1) forward and insert
the bit

2. Release the quick release mechanism

3. Pull on the bit to check that it is securely fitted. If the bit is not secure,
repeat the above procedure

Note: Make sure screwdriver bits used are hardened and suitable for use with
an impact driver

Direction control

• The rotation direction can be set using the Forward/Reverse Switch (5)

• To let the impact driver rotate clockwise, push the Forward/Reverse Switch
to the left

• To let the impact driver rotate anti-clockwise, push the Forward/Reverse
Switch to the right

• When the Forward/Reverse Switch is in the central position, the tool is
locked

WARNING: DO NOT attempt to move the forward/reverse selector when the
tool is running

Operation

WARNING: Always use adequate protective equipment, including eye

protection, respiratory and hearing protection, when working with this tool.

Switching on and off

• To start the tool, squeeze the Speed Control Trigger Switch (3). The LED
Guide Light (7) will illuminate

• Further pressure on the trigger will increase the running speed of the tool

• Release the Speed Control Trigger Switch to stop the tool

Note: It is possible the impact driver may switch off during heavy use due to
thermal protection of the battery and internal components. This may prevent

the tool being used again for a short period of time and does not represent a
fault condition.

Accessories

• A range of accessories, including a 2Ah battery (T20B), 4Ah high capacity
battery (T20HCB) as well as screwdriver bits is available from your Triton
dealer. Spare parts can be purchased from your Triton dealer or online at
www.toolsparesonline.com

Maintenance

• This tool is manufactured using class leading components and makes
use of the latest in intelligent circuitry that protects the tool and its
components. In normal use it should provide a long working life

Cleaning

• Keep your machine clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine’s service life. Clean the body of
your machine with a soft brush or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes

Storage

• Store this tool and its accessories after use in its case, in a dry, secure
place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are
no longer functional and are not viable for repair.

• Do not dispose of power tools, batteries or other waste electrical and
electronic equipment (WEEE), with household waste

• Contact your local waste disposal authority for information on the correct
way to dispose of power tools and batteries

7

869029_Z1MANPRO1.indd 7 26/09/2014 09:00

GB

Troubleshooting

Problem Possible cause Solution

Red charging LED does not illuminate and battery
not charging

Battery pack has low capacity

Impact driver cannot be switched on (trigger
switch does not move)

Impact driver does not start when on/off trigger
switch is depressed

Battery not fully seated Clean battery socket of charger

Charger not powered Recheck mains connection

Battery not being fully charged

Battery pack has been charged over 100 times
and capacity has started to reduce

The forward/reverse switch may be in the middle
(‘locked’) position

Battery completely discharged

Defective battery Replace battery

Machine defective

Charge the battery until the charger indicates a
full charge

This is normal for battery packs. Contact your
Triton dealer to purchase a replacement battery
pack

Slide the forward/reverse switch either to the
left or right

Recharge battery or replace with a fully charged
battery

Contact your Triton dealer or authorised service
centre

8

869029_Z1MANPRO1.indd 8 26/09/2014 09:00

GB

Guarantee

To register your guarantee visit our web site at
www.tritontools.com* and enter your details.

Your details will be included on our mailing list (unless indicated
otherwise) for information on future releases. Details provided will not be
made available to any third party.

Purchase Record

Date of Purchase: ___ / ___ / ____
Model: T20ID Retain your receipt as proof of purchase art pr

Triton Precision Power Tools guar antees to the purchaser of this
product that if any part proves to be defective due to faulty materials or
workmanship within 3 YE ARS from the date of original purchase,
Triton will repair, or at its discretion replace, the faulty part free of
charge.

This guar antee does not apply to commercial use nor does it ex tend to
normal wear and tear or damage as a result of accident , abuse or misuse.

* Register online within 30 days.

Terms & conditions apply.

This does not affect your statutory rights oves to be defecti

9

869029_Z1MANPRO1.indd 9 26/09/2014 09:00

F

Traductions des instructions originales

Nous vous remercions d’avoir choisi cet équipement Triton. Ces instructions contiennent les informations nécessaires au fonctionnement

efficace et sûr de ce produit. Veuillez lire attentivement ce manuel pour vous assurer de tirer pleinement avantage des caractéristiques

uniques de votre nouvel équipement. Gardez ce manuel à portée de main et assurez-vous que tous les utilisateurs l’aient lu et bien compris

avant toute utilisation.

Table des matières

Caractéristiques techniques 10
Nomenclature 11
Symboles 11
Consignes générales de sécurité 11
Consignes de sécurité relatives aux visseuses à choc 12
Consignes de sécurité relatives au

chargeur et aux batteries 12
Usage conforme 13

Déballage 13
Avant utilisation 13
Instructions d’utilisation 14
Accessoires 14
Entretien 14
Recyclage 15
Garantie 15

Caractéristiques techniques

Numéro du modèle T20ID

Visseuse à choc

Tension : 20 V CC

Vitesse à vide : 0 – 2400 min

Fréquences des
impacts :

Contrôle de la
vitesse :

Couple maximum : 160 Nm

Mandrin : à emmanchement 6 pans de 6 mm/ 1/4”

Poids : 1,59 kg (3,51 lbs)

Informations sur le niveau d’intensité sonore et vibratoire

Pression acoustique
Lpa :

Puissance acoustique
Lwa

Incertitude K : 3 dB

Vibration pondérée ah
(polissage) :

Incertitude K : 1,5 m/s²

L’intensité sonore peut dépasser 85 dB(A) et il est nécessaire que
l’utilisateur porte des protections auditives.

3300 min

par pression de la gâchette

93,8 dB(A)

104,8 dB(A)

17,564 m/s

-1

-1

2

Batterie

Technologie : Li-ion à cellules Samsung

Tension : 20 V CC

Modèle et capacité : T20HCB 4,0 Ah

T20B 2,0 Ah

Chargeur

Modèle de chargeur : T20BC

Temps de charge : 1 heure (T20HCB)

Tension d’entrée : Europe : 220-240 V CA 50/60Hz 80 W

Tension de sortie : 20 V CC 3,0 A

Longueur du câble
d’alimentation :

Du fait de l’évolution constante de nos produits, les caractéristiques des
produits Triton peuvent changer sans notification préalable.

30 min (T20B)

Afrique du Sud : 220-240 V CA 50/60Hz 80 W
Australie : 220-240 V CA 50/60Hz 80 W
Japon : 100 V CA 50/60Hz 1,3A
USA/Canada : 120 V CA 60 Hz, 1,3A

(pas pour le modèle US/CAN)

2 m

Attention : Toujours porter des protections sonores lorsque le niveau d’intensité est supérieur à 85 dB(A) et limiter le temps d’exposition si nécessaire. Si l’intensité
sonore devient inconfortable, même avec les protections, arrêter immédiatement d’utiliser l’appareil, vérifier que les protections soient bien mises et qu’elles soient
adéquates avec le niveau sonore produit par l’appareil.

Attention : L’exposition de l’utilisateur aux vibrations peut engendrer une perte du toucher, des engourdissements, des picotements et ainsi réduire la capacité de
préhension. De longues expositions peuvent également provoquer ces symptômes de façon chronique. Si nécessaire, limiter le temps d’exposition aux vibrations,
et porter des gants anti-vibrations. Ne pas utilisez cet appareil avec vos mains sous des conditions en dessous de températures normales, car l’effet vibratoire en
est accentué. Se référer au cas de figures des caractéristiques relatives aux vibrations pour calculer le temps et fréquence d’utilisation de l’appareil.

Les niveaux sonores et vibratoires des caractéristiques techniques sont déterminés en fonction de la norme EN60745 ou autres normes internationales. . Ces
données correspondent à un usage normale de l’appareil, et ce dans des conditions de travail normales. Un appareil mal entretenu, mal assemblé ou mal utilisé
peut augmenter les niveaux sonores et vibratoires. Pour plus d’informations sur la directive des émissions sonores et vibratoires, visitez le site http://osha.europa.
eu/fr.

10

869029_Z1MANPRO1.indd 10 26/09/2014 09:00