TL-WR741N
TL-WR741ND
150Mbps Wireless Lite-N Router
Rev: 1.0.0
1910010159
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)This device may not cause harmful interference.
2)This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- I -
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
National restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country |
Restriction |
Reason/remark |
|
|
|
|
|
Bulgaria |
None |
General authorization required for outdoor use and |
|
public service |
|||
|
|
||
|
|
|
Outdoor use limited to 10 France mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012
Italy |
None |
If used outside of own premises, general authorization is |
|
required |
|||
|
|
||
|
|
|
|
Luxembourg |
None |
General authorization required for network and service |
|
supply(not for spectrum) |
|||
|
|
||
|
|
|
|
Norway |
Implemented |
This subsection does not apply for the geographical area |
|
within a radius of 20 km from the centre of Ny-Ålesund |
|||
|
|
||
|
|
|
|
Russian Federation |
None |
Only for indoor applications |
|
|
|
|
Note: Please don’t use the product outdoors in France.
- II -
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150 Mbps Wireless Lite-N Router
Model No.: TL-WR741N/TL-WR741ND
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC
The above product is in conformity with the following standards or other normative documents
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.8.1:2008 & ETSI EN 301 489-17 V1.3.2:2008 EN60950-1:2006
EN62311:2008
Directives 2004/108/EC
The above product is in conformity with the following standards or other normative documents
EN 55022:2006+A1:2007
EN 55024:1998+A1:2001+A2:2003 EN 61000-3-2:2006
EN 61000-3-3:1995+A1:2001+A2:2005
Directives 2006/95/EC
The above product is in conformity with the following standards or other normative documents
EN60950-1:2006
Person is responsible for marking this declaration:
Zhao Jianjun
Director of International Business
TP-LINK TECHNOLOGIES CO., LTD.
South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,
Shenzhen, P. R. China
|
|
CONTENTS |
|
Package Contents.................................................................................................................................. |
|
1 |
|
Chapter 1. |
Introduction....................................................................................................................... |
2 |
|
1.1 |
Overview of the Router ....................................................................................................... |
2 |
|
1.2 |
Conventions ........................................................................................................................ |
3 |
|
1.3 |
Main Features ..................................................................................................................... |
3 |
|
1.4 |
Panel Layout ....................................................................................................................... |
4 |
|
|
1.4.1 |
The Front Panel...................................................................................................... |
4 |
|
1.4.2 |
The Rear Panel ...................................................................................................... |
5 |
Chapter 2. Connecting the Router..................................................................................................... |
6 |
||
2.1 |
System Requirements......................................................................................................... |
6 |
|
2.2 |
Installation Environment Requirements .............................................................................. |
6 |
|
2.3 |
Connecting the Router ........................................................................................................ |
6 |
|
Chapter 3. Quick Installation Guide................................................................................................... |
8 |
||
3.1 |
TCP/IP Configuration .......................................................................................................... |
8 |
|
3.2 |
Quick Installation Guide ................................................................................................... |
10 |
|
Chapter 4. Configuring the Router ................................................................................................. |
15 |
||
4.1 |
Login ................................................................................................................................ |
|
15 |
4.2 |
Status ............................................................................................................................... |
|
15 |
4.3 |
Quick Setup...................................................................................................................... |
16 |
|
4.4 |
QSS.................................................................................................................................. |
|
16 |
4.5 |
Network ............................................................................................................................ |
23 |
|
|
4.5.1 |
LAN...................................................................................................................... |
23 |
|
4.5.2 |
WAN..................................................................................................................... |
24 |
|
4.5.3 |
MAC Clone .......................................................................................................... |
34 |
4.6 |
Wireless ........................................................................................................................... |
35 |
|
|
4.6.1 |
Wireless Settings................................................................................................. |
35 |
|
4.6.2 |
Wireless Security................................................................................................. |
37 |
|
4.6.3 |
Wireless MAC Filtering ........................................................................................ |
40 |
|
4.6.4 |
Wireless Advanced .............................................................................................. |
43 |
- I -
|
4.6.5 |
Wireless Statistics ................................................................................................ |
44 |
4.7 |
DHCP |
............................................................................................................................... |
45 |
|
4.7.1 |
DHCP Settings ..................................................................................................... |
45 |
|
4.7.2 ................................................................................................ |
DHCP Clients List |
46 |
|
4.7.3 ........................................................................................... |
Address Reservation |
47 |
4.8 |
Forwarding ....................................................................................................................... |
48 |
|
|
4.8.1 ..................................................................................................... |
Virtual Servers |
48 |
|
4.8.2 ..................................................................................................... |
Port Triggering |
50 |
|
4.8.3 ..................................................................................................................... |
DMZ |
52 |
|
4.8.4 ................................................................................................................... |
UPnP |
52 |
4.9 |
Security ............................................................................................................................ |
53 |
|
|
4.9.1 ...................................................................................................... |
Basic Security |
53 |
|
4.9.2 ............................................................................................... |
Advanced Security |
55 |
|
4.9.3 .............................................................................................. |
Local Management |
56 |
|
4.9.4 .......................................................................................... |
Remote Management |
57 |
4.10 |
Parental ...............................................................................................................Control |
58 |
|
4.11 |
Access .................................................................................................................Control |
61 |
|
|
4.11.1 ..................................................................................................................... |
Rule |
61 |
|
4.11.2 ..................................................................................................................... |
Host |
64 |
|
4.11.3 ................................................................................................................... |
Target |
66 |
|
4.11.4 .............................................................................................................. |
Schedule |
68 |
4.12 |
Static Routing................................................................................................................... |
70 |
|
4.13 |
Bandwidth ............................................................................................................Control |
71 |
|
|
4.13.1 ................................................................................................... |
Control Settings |
71 |
|
4.13.2 ............................................................................................................. |
Rules List |
71 |
4.14 |
IP& MAC ......................................................................................................Bing Setting |
73 |
|
|
4.14.1 ................................................................................................... |
Binding Settings |
73 |
|
4.14.2 ............................................................................................................... |
ARP List |
75 |
4.15 |
Dynamic ...................................................................................................................DNS |
75 |
|
|
4.15.1 ............................................................................................... |
Dyndns.org DDNS |
76 |
- II -
4.15.2 |
No-ip.com DDNS ................................................................................................. |
76 |
4.16 System Tools.................................................................................................................... |
77 |
|
4.16.1 |
Time Settings....................................................................................................... |
78 |
4.16.2 |
Diagnostic............................................................................................................ |
79 |
4.16.3 |
Firmware Upgrade............................................................................................... |
80 |
4.16.4 |
Factory Defaults................................................................................................... |
81 |
4.16.5 |
Backup & Restore................................................................................................ |
82 |
4.16.6 |
Reboot ................................................................................................................. |
82 |
4.16.7 |
Password............................................................................................................. |
83 |
4.16.8 |
System log........................................................................................................... |
83 |
4.16.9 |
Statistics............................................................................................................... |
86 |
Appendix A: FAQ ................................................................................................................................ |
|
88 |
Appendix B: Configuring the PC ...................................................................................................... |
93 |
|
Appendix C: Specifications............................................................................................................... |
97 |
|
Appendix D: Glossary........................................................................................................................ |
98 |
- III -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
The following items should be found in your package:
¾TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router
¾DC Power Adapter for TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router
¾Quick Installation Guide
¾Resource CD for TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router, including:
•This Guide
•Other Helpful Information
) Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
- 1 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
Thank you for choosing the TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router.
The TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. Powered by 2x2 MIMO technology, the 150Mbps Wireless Lite-N Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.
Incredible Speed
The TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router provides up to 150Mbps wireless connection with other 802.11n wireless clients. The speed makes it ideal for handling multiple data streams at the same time, which ensures your network stable and smooth. It is compatible with all IEEE 802.11g and IEEE 802.11b products.
Multiple Security Protections
With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2PSK, WPAPSK), as well as advanced Firewall protections, the TL-WR741N/741ND 150Mbps Wireless Lite-N Router provides complete data privacy.
Flexible Access Control
The TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and monitor the network in real time with the remote management function.
Simple Installation
Since the Router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the Router, please look through this guide to know all the Router’s functions.
- 2 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
The Router or TL-WR741N/TL-WR741ND mentioned in this guide stands for TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router without any explanation.
) Note:
The two devices of TL-WR741N and TL-WR741ND are sharing this User Guide. For simplicity, we will take TL-WR741ND for example throughout this Guide.
The differences between them are:
¾TL-WR741N Router with one fixed antennas.
¾TL-WR741ND Router with one detachable antenna.
¾Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to 150Mbps.
¾One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX.
¾Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
¾Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet access.
¾Supports Virtual Server, Special Application and DMZ host.
¾Supports UPnP, Dynamic DNS, Static Routing.
¾Provides Automatic-connection and Scheduled Connection on certain time to the Internet.
¾Connects Internet on demand and disconnects from the Internet when idle for PPPoE.
¾Built-in NAT and DHCP server supporting static IP address distributing.
¾Supports Stateful Packet Inspection
¾Supports VPN Passthrough
¾Supports Parental Control and Access Control.
¾Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control List).
¾Supports Flow Statistics.
¾Supports firmware upgrade and Web management.
-3 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
Figure 1-1 Front Panel sketch
The Router’s LEDs and the QSS button are located on the front panel (View from left to right).
|
Name |
|
Status |
|
|
Indication |
|
Power |
|
Off |
|
Power is off. |
|
|
|
On |
|
|
Power is on. |
|
|
|
|
|
|
||
|
|
|
On |
|
|
The Router is initializing. |
|
System |
|
Flashing |
|
The Router is working properly. |
|
|
|
|
Off |
|
The Router has a system error. |
|
|
WLAN |
|
Off |
|
The Wireless function is disabled. |
|
|
|
Flashing |
|
The Wireless function is enabled. |
||
|
|
|
|
|||
|
|
|
Off |
|
There is no device linked to the corresponding port. |
|
|
WAN, |
|
On |
|
|
There is a device linked to the corresponding port but |
|
LAN 1-4 |
|
|
|
there is no activity. |
|
|
|
|
|
|
||
|
|
|
Flashing |
|
There is an active device linked to the corresponding port. |
|
|
|
|
Slow Flash |
|
|
A wireless device is connecting to the network by QSS |
|
|
|
|
|
function. This process will last for about 2 minutes. |
|
|
|
|
|
|
|
|
|
QSS |
|
|
|
|
A wireless device has been successfully added to the |
|
|
On |
|
|
network by QSS function. The LED will keep on for about |
|
|
|
|
|
|
|
5 minutes. |
|
|
|
Quick Flash |
|
|
A wireless device failed to be added to the network by |
|
|
|
|
|
QSS function. |
|
|
|
|
|
|
|
|
|
|
|
|
Table 1-1 The LEDs Description |
) Note:
After a device is successfully added to the network by QSS function, the QSS LED will keep on for about 5 minutes and then turn off.
- 4 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
¾POWER: The Power socket is where you will connect the power adapter. Please use the power adapter provided with this TL-WR741N/TL-WR741ND 150Mbps Wireless Lite-N Router.
¾1,2,3,4 (LAN): These ports (1, 2, 3, 4) connect the Router to the local PC(s).
¾WAN: This WAN port is where you will connect the DSL/cable Modem, or Ethernet.
¾RESET
There are two ways to reset to the Router's factory defaults:
1)Use the Factory Defaults function on “System Tools → Factory Defaults” page in the Router's Web-based Utility.
2)Use the Factory Default Reset button: With the Router powered on, use a pin to press and hold the Reset button (about 5 seconds) until the SYS LED becomes quick-flash from slow-flash. And then release the button and wait the Router to reboot to its factory default settings.
¾Wireless antenna: To receive and transmit the wireless data.
- 5 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
¾Broadband Internet Access Service (DSL/Cable/Ethernet)
¾One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.)
¾PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
¾TCP/IP protocol on each PC
¾Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
¾Place the Router in a well ventilated place far from any heater or heating vent
¾Avoid direct irradiation of any strong light (such as sunlight)
¾Keep at least 2 inches (5 cm) of clear space around the Router
¾Operating Temperature: 0 ~40 (32 ~104 )
¾Operating Humidity: 10%~90%RH, Non-condensing
Before installing the Router, make sure your PC is connected to the Internet through the broadband service successfully. If there is any problem, please contact your ISP. After that, please install the Router according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
1.Power off your PC, Cable/DSL Modem, and the Router.
2.Locate an optimum location for the Router. The best place is usually at the center of your wireless network.
3.Adjust the direction of the antenna. Normally, upright is a good direction.
4.Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can skip this step.)
5.Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.
6.Connect the power adapter to the power socket on the Router, and the other end into an
-6 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
electrical outlet. The Router will start to work automatically.
7.Power on your PC and Cable/DSL Modem.
Figure 2-1 Hardware Installation of the TL-WR741ND 150Mbps Wireless Lite-N Router
- 7 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
This chapter will show you how to configure the basic functions of your TL-WR741ND 150Mbps Wireless Lite-N Router using Quick Setup Wizard within minutes.
The default IP address of the TL-WR741ND 150Mbps Wireless Lite-N Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for your PC in the following two ways.
¾Configure the IP address manually
1)Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC".
2)Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The Router's default IP address)
¾Obtain an IP address automatically
1)Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC”.
2)Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.1.1, and then press Enter.
¾If the result displayed is similar to the Figure 3-1, it means the connection between your PC and the Router has been established well.
- 8 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
Figure 3-1 Success result of Ping command
¾If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the Router is failed.
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1.Is the connection between your PC and the Router correct?
) Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should be lit.
- 9 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
2.Is the TCP/IP configuration for your PC correct?
) Note:
If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254.
With a Web-based utility, it is easy to configure and manage the TL-WR741ND 150Mbps Wireless Lite-N Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1.To access the configuration utility, open a web-browser and type in the default address http://192.168.1.1 in the address field of the browser.
Figure 3-3 Log in the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the
Enter key.
Figure 3-4 Login Windows
) Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
2.After successfully log in, you can click the Quick Setup menu to quickly configure your Router.
-10 -
|
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
|
|
|
|
|
|
|
|
|
Figure 3-5 Quick Setup
3.Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6.
Figure 3-6 WAN Connection Type
The Router provides Auto-Detect function and supports three popular ways PPPoE, Dynamic IP and Static IP to connect to the Internet. It’s recommended that you make use of the Auto-Detect function. If you are sure of what kind of connection type your ISP provides, you can select the very type and click Next to go on configuring.
4.If you select Auto-Detect, the Router will automatically detect the connection type your ISP provides. Make sure the cable is securely plugged into the WAN port before detection. The appropriate configuration page will be displayed when an active Internet service is successfully detected by the Router.
1)If the connection type detected is PPPoE, the next screen will appear as shown in Figure 3-7.
Figure 3-7 Quick Setup - PPPoE
- 11 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
2)If the connection type detected is Dynamic IP, the next screen will appear as shown in Figure 3-9. Then you can go on with the wireless configuration.
3)If the connection type detected is Static IP, the next screen will appear as shown in Figure 3-8.
Figure 3-8 Quick Setup - Static IP
¾IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field.
¾Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0.
¾Default Gateway - Enter the gateway IP address into the box if required.
¾Primary DNS - Enter the DNS Server IP address into the box if required.
¾Secondary DNS - If your ISP provides another DNS server, enter it into this field.
5.Click Next to continue, the Wireless settings page will appear as shown in Figure 3-9.
- 12 -
|
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
|
|
|
|
|
|
|
|
|
Figure 3-9 Quick Setup – Wireless
¾Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list.
¾SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_xxxxxx (xxxxxx indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive. For example, TP-LINK is NOT the same as tp-link.
¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
¾Channel - This field determines which operating frequency will be used. The default channel is set to 6. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
¾Mode - This field determines the wireless mode which the Router works on.
¾Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically.
¾Max Tx Rate - You can limit the maximum transmission rate of the Router through this field.
-13 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. It is recommended strongly that you choose one of following options to enable security.
¾WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase. z PSK Password - You can enter ASCII or Hexadecimal characters.
For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters.
For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
Please also note the key is case sensitive, this means that upper and lower case keys will affect the outcome. It would also be a good idea to write down the key and all related wireless security settings.
¾No Change - If you chose this option, wireless security configuration will not change!
These settings are only for basic wireless parameters. For advanced settings, please refer to Section 4.6: “Wireless”.
6.Click the Next button. You will then see the Finish page.
If you don’t make any changes on the Wireless page, you will see the Finish page as shown in Figure 3-10. Click the Finish button to finish the Quick Setup.
Figure 3-10 Quick Setup - Finish
If there are something changed on the Wireless page, you will see the Finish page as shown in Figure 3-11. Click the Reboot button to make your wireless configuration to take effect and finish the Quick Setup.
Figure 3-11 Quick Setup - Finish
- 14 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
This chapter will show each Web page's key functions and the configuration way.
After your successful login, you will see the fifteen main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions.
Figure 4-1 the main menu
The detailed explanations for each Web page’s key function are listed below.
The Status page provides the current status information about the Router. All information is read-only.
- 15 -
|
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
|
|
|
|
|
|
|
|
|
Figure 4-2 Router Status
Please refer to Section 3.2: "Quick Installation Guide."
4.4 QSS
This section will guide you to add a new wireless device to an existing network quickly by QSS (Quick Secure Setup) function.
- 16 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
a). Choose menu “QSS”, you will see the next screen (shown in Figure 4-3 ).
Figure 4-3 QSS
¾QSS Status - Enable or disable the QSS function here.
¾Current PIN - The current value of the Router's PIN is displayed here. The default PIN of the Router can be found in the label or User Guide.
¾Restore PIN - Restore the PIN of the Router to its default.
¾Gen New PIN - Click this button, and then you can get a new random value for the Router's PIN. You can ensure the network security by generating a new PIN.
¾Add device - You can add a new device to the existing network manually by clicking this button.
b). To add a new device:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration (PBC) method or PIN method.
) Note:
To build a successful connection by QSS, you should also do the corresponding configuration of the new device for QSS function meanwhile.
For the configuration of the new device, here takes the Wireless Adapter of our company for example.
I.By PBC
If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods.
Method One:
Step 1: Press the QSS button on the front panel of the Router.
- 17 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
Step 2: Press and hold the QSS button of the adapter directly for 2 or 3 seconds.
Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration.
The QSS Configuration Screen of Wireless Adapter
Method Two:
Step 1: Press the QSS button on the front panel of the Router.
Step 2: For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the QSS as below, and click Next.
- 18 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
The QSS Configuration Screen of Wireless Adapter
Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration.
The QSS Configuration Screen of Wireless Adapter
Method Three:
Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-3, then the following screen will appear.
- 19 -
|
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
|
|
|
|
|
|
|
|
|
Figure 4-4 Add A New Device
Step 2: Choose “Press the button of the new device in two minutes” and click Connect.
Step 3: For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the QSS as below, and click Next.
The QSS Configuration Screen of Wireless Adapter
Step 4: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration.
- 20 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
The QSS Configuration Screen of Wireless Adapter
II. By PIN
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.
Method One: Enter the PIN into my Router
Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-3, then the following screen will appear.
Step 2: Choose “Enter the new device's PIN” and enter the PIN code of the wireless adapter in the field after PIN as shown in the figure above. Then click Connect.
) Note:
The PIN code of the adapter is always displayed on the QSS configuration screen
Step 3: For the configuration of the wireless adapter, please choose “Enter a PIN into my access point or a registrar” in the configuration utility of the QSS as below, and click
Next.
- 21 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
The QSS Configuration Screen of Wireless Adapter
) Note:
In this example, the default PIN code of this adapter is 16952898 as the above figure shown.
Method Two: Enter the PIN from my Router
Step 1: Get the Current PIN code of the Router in Figure 4-3 (each Router has its unique PIN code. Here takes the PIN code 12345670 of this Router for example).
Step 2: For the configuration of the wireless adapter, please choose “Enter a PIN from my access point” in the configuration utility of the QSS as below, and enter the PIN code of the Router into the field after “Access Point PIN”. Then click Next.
The QSS Configuration Screen of Wireless Adapter
- 22 -
TL-WR741N/TL-WR741ND |
150Mbps Wireless Lite-N Router |
) Note:
The default PIN code of the Router can be found in its label or the QSS configuration screen as Figure 4-3.
c). You will see the following screen when the new device successfully connected to the network.
) Note:
a.The QSS LED on the Router will light green for five minutes if the device has been successfully added to the network.
b.The QSS function cannot be configured if the Wireless Function of the Router is disabled. Please make sure the Wireless Function is enabled before configuring the QSS.
Figure 4-5 the Network menu
There are three submenus under the Network menu (shown in Figure 4-5): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function.
4.5.1 LAN
Choose menu “Network → LAN”, you can configure the IP parameters of the LAN on the screen as below.
Figure 4-6 LAN
- 23 -