Toyota Hilux, UH9000S, UH9060S, UH9080S Fitting Instructions Manual
UHF CB Transceiver
UH9000S / UH9060S / UH9080S
Fitting Instructions
Hilux
Fitting Kit Part Number: UNIFK001
Fitting Instructions
UH9000S / UH9060S / UH9080S
Speaker
A
A
Microphone
UH9000S
UHF CB Transceiver
Front
Rear
ccessory
Power
+
Earth
Fuse
UH9060S / UH9080S
Remote LCD
Speaker
Microphone
Power
Lead Patch
Harness
Antenna
Connector
UHF CB Transceiver
Front
Rear
Extension
Cable
(Optional)
Antenna
Connector
Power
ccessory
Power
+
Earth
Fuse
Lead Patch
Harness
Page 2 of 14
Fitting Instructions
UH9000S / UH9060S / UH9080S
WARNING
This vehicle is equipped with Supplemental Restraint System (SRS) airbags and seatbelt pretensioners.
Before starting work, wait at least 90 seconds after the ignition switch is turned off and the negative (-) battery terminal
cable is disconnected.
SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off
and disconnecting the negative (-) battery terminal cable, SRS parts may deploy possibly causing serious injuries.
WARNING
Do not install any parts in a location that may interfere with the operation and deployment of the SRS airbags or seatbelt
pretensioners, including driver, front passenger and knee SRS airbags if tted. Doing so may result in serious injury or
death.
PREPARATION
• Follow all standard workshop and occupational health and safety practices during the installation process.
• Check and note any existing marks or damage to the vehicle.
• Before starting the installation thoroughly read through these installation instructions then follow the tting sequence as described.
• Check that the UHF CB transceiver kit is complete.
• Take all possible precautions to avoid damaging the vehicle’s interior and exterior during the installation. Use protective tape on
parts and tools where necessary.
• To avoid damage to the wiring harness and antenna cable, avoid contact with sharp edges. Cable tie securely every 200 mm.
• Ensure all removed parts are re-tted correctly.
SPECIAL TOOLS
• Trim removal tools
• Protective tape
• Lead wire
PARTS LIST - UHF CB TRANSCEIVER KITS
Model UHF CB Transceiver Kit Fitting Kit Part Number
HILUX
PARTS LIST - ANTENNA
Model Antenna Part Number Description
HILUX
UH9000S
UNIFK001UH9060S
UH9080S
AT970BKTWIN Antenna Dual Whip Black
AT970WTWIN Antenna Dual Whip White
AT970BK Antenna 1200mm Black
AT970W Antenna 1200mm White
AT890BK Antenna 1000mm Black
AT890W Antenna 1000mm White
AT880TWIN Antenna Dual Whip Stainless Steel
Page 3 of 14
Fitting Instructions
UH9000S / UH9060S / UH9080S
REMOVAL
Removal - Engine Bay
1. Open the bonnet.
2. Remove the radiator shroud (7 scrivets).
Push in the centre of the scrivets and pull up the shroud to
remove. Take care to retain all scrivets.
3. Disconnect the (-) negative battery terminal cable.
4. Cut the outer tang off the rewall grommet where
indicated.
Note: Refer to the Alternate antenna cable entry point
on page 8 if both grommet entry points are being used
Removal - Interior
1. Remove the front passenger’s side instrument panel under
cover sub-assembly.
Use a at blade screwdriver to release the (4) clips, lower
slightly and pull away.
Page 4 of 14
Fitting Instructions
UH9000S / UH9060S / UH9080S
2. Unclip (4 [ ]) and remove the front passenger’s side scuff
plate.
3. UH9060S / UH9080S only - Remove the glovebox.
Open the glovebox and remove the (2) stopper pins by
rotating 90º and pulling out. Unclip the damper rod. Open
the glovebox fully and pull away from the lower retaining
clips.
4. Remove the front passenger’s cowl side trim board
(1 screw and 2 clips [
Prise off carefully at retaining clip locations to avoid
damaging the clips and panel.
])
Page 5 of 14
Loading...