Toyota TY-71-00-G3 User Manual

TOYOTA TUNDRA 2000-2006
TOYOTA SEQUOIA 2001-2007
(MANUAL CLIMATE CONTROL ONLY)
PART NUMBER: TY-71-00-G3
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling
wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
#2 Phillips screwdriver, hook tools, 5/64” drill bit and drill, marking pen. VSM G3, A Plate, J Stem, two (2) #8 1/2” screws Right of air vent
TOOLS REQUIRED:
PARTS INCLUDED:
LOCATION:
STEP 1. Locate the two air vents that are on the right and left sides of the radio. Remove both of these air vents by inserting the hook tool between the vents and the bezel and carefully prying outward on the vents to remove. Set the vents aside. Inside the vent cavities locate and remove two (2) Phillips screws using the Phillips screwdriver. Set the screws aside. STEP 2. Locate the three knobs that are on the climate control. Grasp the knobs and carefully pull toward you to remove. Set the knobs aside. Locate and remove the three(3) Phillips screws that are behind the knobs. Set the screws aside. Grasp the top middle section of the bezel just above the radio and carefully pull towards you releasing the top clip. Insert both your hands into the air vent cavities. Grasp the bezel and pull toward you to release a series of six clips that are behind and attached to the back of the climate control. These clips hold the lower section of the bezel in place. When the bezel is loose do not disconnect any wiring. Let the bezel hang. STEP 3. Locate the flat section of plastic to the right of the right air vent. Place the VSM G3 over this section of plastic, making sure that the bottom of the G3 is level. Once the G3 is in position, mark two (2) spots for drilling pilot holes using the two (2) holes in the G3 as a guide. Set the mount aside. Carefully drill two (2) pilot holes using the 5/64” drill bit and drill, making sure to not drill too deep. Place the VSM G3 over the two pilot holes. Insert the two (2) #8 x 1/2” provided screws and tighten. STEP 4. Re-assemble the dash in reverse order. This completes the installation of your VSM G3.
Note: See the Assembly Instructions for G3 Components for additional information.
Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this VSM
G3. Pro.Fit International may not be held liable for any personal injury resulting from accident or improper installation. Pro.Fit International,
Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876
© Pro.Fit International, Eagan, MN 2008
1
2
3
See page 2 for Automatic Climate Control
Page 1 of 3
When properly installed, the metal between the ball and 2 small holes is all that is exposed.
(Some exceptions apply).
View Instruction & Updates
Online at
www.pro-fit-intl.com
TOYOTA TUNDRA 2000-2006
TOYOTA SEQUOIA 2001-2007
(AUTOMATIC CLIMATE CONTROL ONLY)
PART NUMBER: TY-71-00-G3
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling
wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
#2 Phillips screwdriver, hook tools, 5/64” drill bit and drill, Dash Trim Removal Tool (DTRT), marking pen. VSM G3, A Plate, J Stem, two (2) #8 1/2” screws Right of air vent
TOOLS REQUIRED:
PARTS INCLUDED:
LOCATION:
STEP 1. Push the top of the left and right air vents into the dash, exposing two (2) Phillips screws, (See top picture). Remove the screws. There are five (5) retainer clips that hold the radio bezel in place. They are located at top center, left and right middle and the remaining two (2) on the bottom of the bezel. Using a DTRT, gently twist to release the clips and remove the bezel. Set the bezel aside.
STEP 2. Locate the flat section of plastic to the right of the right air vent, (See middle picture). Place the VSM G3 over this section of plastic, making sure that the bottom of the VSM G3 is level. Once the G3 is in position, mark two (2) spots for drilling pilot holes using the two (2) holes in the G3 as a guide. Set the mount aside. Carefully drill two (2) pilot holes using the 5/64” drill bit and drill, making sure not to drill too deep. Place the VSM G3 over the two pilot holes. Insert the two (2) provided screws and tighten.
STEP 3. Re-assemble the dash in reverse order. This completes the installation of your VSM G3.
Note: See the Assembly Instructions for G3 Components for additional information.
1
2
3
Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this VSM
G3. Pro.Fit International may not be held liable for any personal injury resulting from accident or improper installation. Pro.Fit International,
Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876
© Pro.Fit International, Eagan, MN 2008
Page 2 of 3
View Instruction & Updates
Online at
www.pro-fit-intl.com
When properly installed, the metal between the ball and 2 small holes is all that is exposed.
(Some exceptions apply).
Loading...
+ 1 hidden pages