Toyota TVSS IV-S Settings Manual
TOYOTA MOTOR CORPORATION
Manual Ref. Nr. T4SLSET-2-0
ALARM
TOYOTA VEHICLE SECURITY SYSTEM
Setting Guide
(LHD)
TTVVSSSS IIVV--SS
TABLE OF CONTENTS
(LHD) - 3
Setting Guide TVSS IV-S
Connection and Function Test
..................................................................................................................................................................................... 4
Radar Sensor Sensitivity Check and Adjustment
............................................................................................................................ 8
Glass Breakage Sensor Sensitivity Check and Adjustment
............................................................................................. 10
Selectable Functions
..................................................................................................................................................................................................................
12
Changing the Functions
........................................................................................................................................................................................................
13
- Arming mode
.................................................................................................................................................................................................................... 13
- Status monitor LED flashing
......................................................................................................................................................................... 14
- Piezo buzzer defeat
................................................................................................................................................................................................. 15
- Answer back
...................................................................................................................................................................................................................... 16
- Ignition controlled door lock
........................................................................................................................................................................... 17
How to Verify the Latest Alarm Cause
.............................................................................................................................................................. 18
Temporary Override
...................................................................................................................................................................................................................... 19
(LHD) - 4
CONNECTION AND FUNCTION TEST
Setting Guide TVSS IV-S
TESTING MODE
n PREPARATION
1) Check that all connectors and terminals of the fitting kit wiring harnesses (main) and (engine)
are fitted correctly.
2) Reconnect the negative battery cable.
3) Close boot and bonnet completely.
4) Step in the vehicle and make sure that all doors are closed completely.
5) Open all windows and put the dome light switch into the “DOOR” position.
6) Remove the key from the ignition key cylinder and push the “unlock“ button of the remote control.
Ë Indicator lights will flash twice.
7) Insert the key into the ignition key cylinder.
8) Wait for more than 5 seconds.
9) After turning the key to the ACC position, turn the key from the ACC
to the ON position five times (Last position : ON).
Ë Status Monitor LED will illuminate for 30 seconds.
10) While the LED is illuminated :
• Open and close the driver’s door 7 times.
• Turn the key to the LOCK position.
Ë LED will flash for 15 seconds.
Ë Indicator lights will flash 7 times.
11) While the LED is flashing :
• Remove the key from the ignition key cylinder.
12) Step out of the vehicle and close the driver’s door again.
The system is now ready for testing.
n RADAR SENSOR TEST (if fitted)
13) Wait until the LED stops flashing.
Ë Status Monitor LED will illuminate for 30 seconds.
14) While the LED is illuminating :
• Put your hand through the opening of the window to trigger the radar sensor.
Ë Indicator lights will flash once.
(Refer to pages 8 & 9 for radar sensitivity adjustment).
n DOOR SWITCHES TEST
15) Wait till the LED starts flashing again then open and close the driver’s DOOR.
Ë Indicator lights will flash once.
16) Test each remaining door (repeating step 15).
n BOOT SWITCH TEST
17) Open and close the BOOT.
Ë Indicator lights will flash once.
Verify the connections and functions of TVSS before mounting the TVSS ECU and refitting the removed parts.
Follow all procedures below :
ACC
ON
START
LOCK
(LHD) - 5
Setting Guide TVSS IV-S
n BONNET SWITCH TEST (if fitted)
18) Open and close the BONNET.
Ë Indicator lights will flash once.
n REMOTE CONTROL TEST
19) Press the “LOCK”-button of the remote control.
Ë Indicator lights will flash once.
Ë Doors will lock.
20) Press the “UNLOCK”-button of the remote control.
Ë Indicator lights will flash once.
Ë Doors will unlock.
n KEY UNLOCK WARNING SWITCH TEST (key detection switch)
21) Step in the vehicle and close the door.
Ë Indicator lights will flash once.
22) Insert the key into the ignition key cylinder.
Ë Indicator lights will flash once.
n IGNITION SWITCH, DOME LIGHT, SIREN AND HORN TEST
23) Turn the key to the ignition-ON position.
Ë Indicator lights will illuminate for 1 second.
Ë Dome light will illuminate for 1 second.
Ë The horn will sound for 1 second.
n GLASS BREAKAGE SENSOR TEST (If fitted)
24) Close the driver’s door window.
25) Step out of the vehicle and close all doors.
Ë Indicator lights will flash once.
26) Tap the driver’s door window with moderate force, by using a coin.
Ë Indicator lights will flash once.
(Refer to pages 10 and 11 for Glass Breakage Sensitivity Adjustment.)
n PIEZO BUZZER TEST (if selected see page 12) AND TEST FINISH
27) Step in the vehicle and close all doors.
Ë Indicator lights will flash once.
28) Turn the key to the LOCK-position.
Ë The piezo buzzer of the siren will shortly sound.
Ë Indicator lights will flash TWICE.
Ë Status monitor LED will stop flashing.
(LHD) - 6
Setting Guide TVSS IV-S
STANDARD MODE
n REMOTE OPERATION
1) Remove the key from the ignition key cylinder and make sure that all doors, boot and bonnet are completely closed.
2) Press the "LOCK"-button of the remote control once.
Ë Indicator lights will flash once.
Ë Status Monitor LED will start flashing.
Ë Doors will lock.
3) Push the "UNLOCK" button of the remote control.
Ë Indicator lights will flash twice.
Ë Status Monitor LED will stop flashing.
Ë Dome light will illuminate for 5 seconds.
Ë Doors will unlock.
n AUTO-REARMING (AUTO-RELOCK)
4) Press the "UNLOCK"-button of the remote control.
Ë Indicator lights will flash twice.
Ë Status Monitor LED will stop flashing.
Ë Dome light will illuminate for 5 seconds.
Ë Doors will unlock.
5) Wait for 30 seconds.
Ë Indicator lights will flash once.
Ë Status Monitor LED will start flashing.
Ë Doors will lock.
Important notes : a) The system will NOT Auto-rearm (NOT relock) if any of the 4 doors or bonnet
are opened after disarming the system.
b) Sedan models WILL Auto-rearm (relock) after 30 seconds if the boot has been
opened after disarming the system.
n AUTOMATIC (PASSIVE) ARMING
(if selected see page 12)
6) Open the driver’s door window.
7) Close all doors, boot and bonnet completely.
8) Wait for 45 seconds, then ;
Ë Indicator lights will illuminate for 2 seconds.
Ë Status Monitor LED will flash continuously.
n ARMING WITHOUT RADAR SENSOR DETECTION
Note : Confirm first that the radar sensor triggers the alarm.
Refer to page 8 & 9 for radar sensor sensitivity adjustment.
9) Open a window.
10) Press the "UNLOCK"-button of the remote control.
Ë Indicator lights will flash twice.
Ë Status Monitor LED will stop flashing.
Ë Dome light will illuminate for 5 seconds.
Ë Doors will unlock.
11) Press the “LOCK”-button of the remote control once.
Ë Indicator lights will flash once (1 second).
Ë Status Monitor LED will start flashing.
Ë Doors will lock.
12) Press the “LOCK”-button of the remote control again within 15 seconds from step 7.
Ë Indicator lights will flash once, but this is a longer flash (3 seconds).
(LHD) - 7
Setting Guide TVSS IV-S
13) Wait for 15 seconds.
14) Insert your hand into the vehicle by the open window and wave it widely.
Ë No response.
n ALARM AND ALARM MEMORY
15) Press the “LOCK”-button of the remote control once.
Ë Indicator lights will flash once.
Ë Status Monitor LED will start flashing.
Ë Doors will lock.
16) Open a door by the key method.
Ë The siren (if fitted) will sound for 30 seconds.
Ë The horn will sound for 30 seconds.
Ë Indicator lights will flash rapidly for 30 seconds.
Ë Status Monitor LED will illuminate for 30 seconds.
Ë Dome light illuminates for 30 seconds.
17) After step 13) has finished completely, press the “UNLOCK”-button of the remote control.
Ë Indicator lights will flash three times.
Ë Status Monitor LED will stop flashing.
Ë Dome light will illuminate for 5 seconds.
Ë Doors will unlock.
Ë The siren (if fitted) will stop sounding.
Ë The horn will stop sounding.
n DOOR AJAR WARNING (if fitted, see page 12)
Note : This function is a default setting but can be deleted. Refer to page 15 “Piezo defeat”.
18) Open a door.
19) Press the “LOCK”-button of the remote control.
Ë The piezo buzzer of the siren will sound for 15 seconds.
Ë Doors will remain unlocked.
n IGNITION CONTROLLED DOOR LOCK (if selected, see page 12)
Note : This function is default ON but can be deleted. Refer to page 17 “Ignition controlled door lock”.
20) Step in the vehicle and close all doors.
21) Insert the key into the ignition key cylinder.
22) Turn the key to the “ON” position.
Ë Doors will lock.
Overrule : The door lock will be overruled by operating the “central lock button” or manual door knob operation.
23) Turn the ignition OFF.
Ë Doors will unlock.
Remark : If the Ignition is turned ON a second
time the “ignition controlled door lock” will NOT operate again.
n Warning for siren disconnection
When the siren is disconnected from the power supply :
(for example vehicle battery disconnection)
a) in armed condition : The siren will start sounding (tampermode) 100 dB.
b) in disarmed condition : The siren will bleep discretely for about 7 seconds.
RADAR SENSOR SENSITIVITY CHECK AND ADJUSTMENT
(from next page)
Yes
Fig. 6
(LHD) - 8
Setting Guide TVSS IV-S
Verify and adjust the radar sensor sensitivity before completing the installation of the TVSS and the refitting of
the removed parts. Follow the procedures below:
PREPARATION
1) Check that all connectors and terminals of the fitting kit wiring harnesses (main) and (engine) are fitted correctly.
2) Reconnect the negative battery cable.
3) Open all the windows and remove the ignition key.
4) Verify that the trimmer of the radar sensor is at the correct position (see Installation Instructions manual for
the vehicle).
VERIFICATION AND
ADJUSTMENT
1) Push the “LOCK” button
of the remote to arm the
system.
2) Wait for 15 seconds to
get ready for the radar
sensor test.
3) Place your hand very close to the driver’s window
area. Then wave your
hand sideways across
about 30 cm span several times. (The purpose
of this is to simulate a
person’s movement passing close to the vehicle).
(See figure 6).
4) Is the alarm triggered ?
• Status monitor LED will
illuminate for 30 seconds.
• Dome light will illuminate.
• Indicator lights will flash.
• Siren (if fitted) will sound.
• Horn will sound.
Yes The sensor is too sensitive
and must be adjusted.
No The sensor is not too sen-
sitive.
8) Push the “UNLOCK” button of the remote once to
stop alarming and disarm
the system.
9) Decrease the sensitivity
of the radar sensor by turning the trimmer slightly
counterclockwise.
(see figure 7)
Loading...