Toyota TVIP-RS3200 Programming Manual
TOYOTA TVIP SYSTEM PROGRAMMING Page 1
PROGRAMMING TABLE OF CONTENTS
RS3200 PROGRAMMING PAGE
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM 2, 3
REPROGRAM EXISTING REMOTE CONTROLS 4, 5
REMOTE CONTROL FUNCTION SELECT 6, 7
CLEAR ALL REMOTE CONTROL CODES 8
PASSIVE ARMING ON/ OFF SELECTION AND 9
ENTRY DELAY TIME SELECTION
IGNITION−CONTROLLED AUTOMATIC DOOR 10
LOCK/ UNLOCK
RS3200 PLUS PROGRAMMING
PASSIVE ARMING ON/ OFF SELECTION AND 11
ENTRY DELAY TIME SELECTION
Notes:
For factory remote keyless entry system programming information, refer to the
vehicle
s repair manual.
Refer to the RS3000 Owner
s guide for RS3000 feature programming.
Page 2 TOYOTA TVIP SYSTEM PROGRAMMING−RS3200
s
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM
Follow this procedure to add additional remote controls to a system. The RS3200 may be programmed to
operate with a maximum of four remote controls. When a new remote controls is programmed, it will work
in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button
function on 4 button remote controls); to change the operation mode, you must perform the separate
REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7.
1. Before you begin:
Open the driver s door and remove the key
from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into,
and remove it from
the ignition switch 2
times.
e. Insert the key into,
the ignition switch
and leave it in.
i. The tail and marker lights flash 1 time, the
buzzer chirps 1 time and the doors lock
and unlock 1 time.*
* If the system does not activate the lights, buzzer and door locks 1 time, start over.
b. Close, then open
the driver s door 2
times.
f. Close the driver
door.
c. Insert the key into,
and remove it from
the ignition switch 1
time.
g. Turn the key from
LOCK to ON, then
back to LOCK.
d. Close, then open
the driver s door 2
times.
h. Remove the key
from the ignition
switch.
TOYOTA TVIP SYSTEM PROGRAMMING Page 3
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM (continued)
3. Program (add) an additional remote control.
a. Press and release
both the LOCK and
UNLOCK buttons
on one remote
control at the same
time.
Note: Repeat the above steps to add additional remote controls.
4. Complete the programming steps.
b. Press and release
the LOCK button.
c. The tail and marker lights flash 1 time, the
buzzer chirps 1 time, and the doors lock
and unlock 1 time.*
a. Open the driver s door
* If the system activates the lights, buzzer and door locks 2 times, start over.
Page 4 TOYOTA TVIP SYSTEM PROGRAMMING−RS3200
s
REPROGRAM EXISTING REMOTE CONTROLS
Follow this procedure to clear all existing remote control codes and reprogram existing remote controls to
a system. When existing remote controls are reprogrammed, they will work in the default operation mode
(press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote
controls); to change the operation mode, you must perform the separate REMOTE CONTROL
FUNCTION SELECT procedure as shown on pages 6 and 7.
1. Before you begin:
Open the driver s door and remove the key
from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into,
and remove it from
the ignition switch 2
times.
e. Insert the key into,
the ignition switch
and leave it in.
i. The tail and marker lights flash 2 times,
the buzzer chirps 2 times and the doors
lock and unlock 2 times.*
*If the system does not activate the lights, buzzer and door locks 2 times, start over.
b. Close, then open
the driver s door 2
times.
f. Close the driver
door.
c. Insert the key into,
and remove it from
the ignition switch 1
time.
g. Turn the key from
LOCK to ON 2
times (ending at
LOCK).
d. Close, then open
h. Remove the key
the driver s door 2
times.
from the ignition
switch.
Loading...