17. CS (Chip Select) 18. Cont1(RF In / Out Select)
1.5 19. Cont2(RF In / Out Select) 20. Cont3(RF Amp Switch))
2
20
1
19
TOPCON CORPORATION
RF-10 User Manual Rev. 1
Page 4 of 8
1.5 Outline View
1.6 Package Dimensions
10-JUNE-2011
Pattern Antenna
Interface connector
38.7
Left Side View Top View
Side View
Weight 6g
19.0
5.9
Right Side View
TOPCON CORPORATION
RF-10 User Manual Rev. 1
Page 5 of 8
2. Characteristics
2.1 Electrical Characteristics
Absolute Maximum Rating
Rating
Minimum
10-JUNE-2011
Typical
Maximum
Unit
Supply Voltage
Operating Temperature
Range
RX Current consumption
TX Current consumption
3.2
-20
3.5
25
6.5
55
36
40
V
C
mA
mA
2.2 RF Characteristics
Transmitter
Specification Condition Min. Typ. Max.
Output Transmit Power Normal -1dBm
Frequency Range Normal GHz2.401 2.47975
20dB Bandwidth Normal MHz0.1
Modulation Characteristics Normal MHz0.05
Carrier Frequency Drift -20 ~ +50 C2.5ppm
Receiver
Specification Condition Min. Typ. Max.
Sensitivity BER 0.1%
Maximum Input Level Normal -20dBm
Adjacent Channel rejection Normal 18dB
-90dBm
TOPCON CORPORATION
RF-10 User Manual Rev. 1
Page 6 of 8
10-JUNE-2011
3. Notes
FCC Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
MANUFACTURER FOR COMPLIANCE COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT
CAUTION: This device and its antenna(s) must not be co-located or operating
in conjunction with any other antenna or transmitter. End user
cannot modify this transmitter device. Any unauthorized
modification made on the device could avoid the user's authority
to operate this device.
CAUTION: To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20cm must be maintained between
the antenna of this device and all persons.
The following sentence has to be displayed on the outside of the device in
which the transmitter module is installed:
“Contains FCC ID:H5P-RF10
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TOPCON CORPORATION
RF-10 User Manual Rev. 1
Page 7 of 8
10-JUNE-2011
IC Statements:
The term “IC:” before the radio certification number only signifies that Industry
Canada technical specifications were met.
This device complies with RSS 210 of Industry Canada “IC”.
“Operation is subject to the following two conditions: (1) this device may not
cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.”
"The installer of this radio equipment must ensure that the antenna is located or
pointed such that it does not emit RF field in excess of Health
Canada limits for the general population; consult Safety Code 6,
obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb"
L’ utililisation de ce dispositif est autorisée seulement aux conditions
suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt
à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif.
"The installer of this radio equipment must ensure that the antenna is located or
pointed such that it does not emit RF field in excess of Health
Canada limits for the general population; consult Safety Code 6,
obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb"
“To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that permitted for successful communication.”
The following sentence has to be displayed on the outside of the device in
which the transmitter module is installed:
“Contains IC:6050A-RF10
TOPCON CORPORATION
RF-10 User Manual Rev. 1
Page 8 of 8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.