Europe, Middle East
ENGLISH
FRANÇAIS
DEUTSCH
NEDERLANDS
ITALIANO
ESPAÑOL
PORTUGUÊS
РУССКИЙ
ΕΛΛΗΝΙΚΑ
TÜRKÇE
POLSKI
ﺔﻴﺑﺮﻌﻟا
North America/
Norteamérica
ENGLISH
FRANÇAIS
ESPAÑOL
Latin America/
América Latina
ENGLISH
ESPAÑOL
PORTUGUÊS
Asia Pacic
日本語
繁體中文
한국어
1/22
For Xbox One and Windows
User Manual
2/22
TECHNICAL FEATURES
5 Xbox Guide button + white indicator light
9 Metal fastening screw
1 Base
2 Wheel
3 2 sequential paddle shifters (up & down)
4 D-pad with push button
6 MODE button + red/green indicator light
7 Large threaded hole (for attachment system
and fastening screw)
8 Attachment system
3/22
15 Thrustmaster Quick Release
18 Connector for pedal set
19 Connector for TH8A shifter (shifter sold
22 Removable USB cable
16 Connector for TURBO POWER power
supply
17 Connector for removable USB cable
PLUGGING THE WHEEL INTO AN ELECTRICAL OUTLET:
Never plug the TURBO POWER power supply into an electrical outlet with a different
voltage! The TURBO POWER power supply’s voltage is indicated on the label located above the female
connector for the power supply cable.
Never connect a power supply other than the TURBO POWER power supply to the TS-XW
RACER base, even if the connector is compatible! For example, never connect the power adapter for
the T500 RS wheel to the TS-XW RACER base.
separately)
20 TURBO POWER power supply
21 Power supply cable
PLEASE READ CAREFULLY!
4/22
WARNING
Before using this product, please read this manual carefully and save it for later reference.
Warning – Electrical shock
* Keep the product in a dry location and do not expose it to dust or sunlight.
* Do not twist or pull on the connectors and cables.
* Do not spill any liquid on the product or its connectors.
* Do not short-circuit the product.
* Never dismantle the product; do not throw it onto a fire and do not expose it to high temperatures.
* Do not use a power supply cable other than the one provided with your racing wheel.
* Do not use the power supply cable if the cable or its connectors are damaged, split or broken.
* Make sure that the power supply cable is properly plugged into an electrical outlet, and properly
connected to the connector at the rear of the racing wheel’s base.
* Do not open up the racing wheel: there are no user-serviceable parts inside. Any repairs must be
carried out by the manufacturer, its authorized representative or a qualified technician.
* Only use attachment systems/accessories specified by the manufacturer.
* If the racing wheel is operating abnormally (if it is emitting any abnormal sounds, heat or odors), stop
using it immediately, unplug the power supply cable from the electrical outlet and disconnect the other
cables.
* If you will not be using the racing wheel for an extended period of time, unplug its power supply cable
from the electrical outl et.
* The electrical outlet must be located near the equipment and must be easily accessible.
Air vents
Make sure not to block any of the air vents on the racing wheel’s base. For optimal ventilation, make sure
to do the following:
* Position the wheel’s base at least 10 cm away from any wall surfaces.
* Do not place the base in any tight spaces.
* Do not cover the base.
* Do not let any dust build up on the air vents.
For safety reasons, never use the pedal set with bare feet
THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF
INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.
Warning – Injuries due to Force Feedback and repeated movements
Playing with a Force Feedback racing wheel may cause muscle or joint pain. To avoid any problems:
* Avoid lengthy gaming periods.
* Take 10 to 15 minute breaks after each hour of play.
* If you feel any fatigue or pain in your hands, wrists, arms, feet or legs, stop playing and rest for a few
hours before you start playing again.
or while wearing only socks on your feet.
5/22
16 years of age or older
Warning – Injuries due to Force Feedback and repeated movements (continued)
* If the symptoms or pain indicated persist when you start playing again, stop playing and consult your
doctor.
* Keep out of children’s reach.
* During gameplay, always leave both hands correctly positioned on the wheel without completely
letting go.
* During gameplay, never place your hands or your fingers under the pedals or anywhere near the
pedal set.
* During calibration and gameplay, never place your hand or your arm through the openings in the
racing wheel.
* Make sure that the racing wheel’s base is properly secured, as per this manual’s instructions.
HEAVY PRODUCT
Product to be handled only by users
Be careful not to drop the product on
yourself or on anyone else!
ALWAYS
6/22
COMPATIBILITY WITH THE THRUSTMASTER ECOSYSTEM
Pedal sets
The TS-XW RACER base is compatible:
- On Xbox One and Windows, with the Thrustmaster T3PA and T3PA-PRO pedal sets that connect
directly to the connector for pedal set (18).
- On Windows, with the Thrustmaster DB9 PEDALS T.RJ12 ADAPTER that enables the nonThrustmaster pedal sets equipped with a DB9 connector to connect to the connector for pedal set (18).
- On Windows (only), with all the USB pedal sets on the market (in games supporting MULTI-USB and
USB pedal sets).
Wheels
The TS-XW RACER base is compatible, on Xbox One and Windows, with all Thrustmaster detachable
wheels, including:
- Ferrari 599XX EVO 30 Wheel Add-On Alcantara Edition
- Ferrari F1 Wheel Add-On
- Ferrari GTE Wheel Add-On Ferrari 458 Challenge Edition
- TM Leather 28 GT Wheel Add-On
- TM Open Wheel Add-On
- TM Competition Wheel Sparco® P310 Mod
- TM Rally Wheel Add-On Sparco® R383 Mod
- etc.
Shifters
The TS-XW RACER base is compatible:
- On Xbox One, with the Thrustmaster TH8A Shifter Add-On shifter: connect it directly to the connector
for TH8A shifter (19) for the “Sequential (+/-)” and “H-pattern (7+1)” modes.
- On Windows, with the Thrustmaster TH8A Shifter Add-On shifter: connect it directly to the connector
for TH8A shifter (19) for the “Sequential (+/-)”mode.
- On Windows, with the Thrustmaster TH8A Shifter Add-On shifter: connect it to a USB port for the
“Sequential (+/-)”, “H-pattern (7+1)” and ANALOG / HANDBRAKE modes.
- On Windows, with all the USB shifters on the market (in games supporting MULTI-USB and USB
shifters).
HELP FILES AND FAQS (not included in this manual)
Please visit http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, and then
select Manual or FAQ.
7/22
INSTALLING THE WHEEL ON ITS BASE
Align the connector positions using the arrows:
Base (1) connector: Arrow pointing upwards
Racing wheel (2) connector: Arrow pointing upwards
Once the connectors are correctly positioned, simply rotate the Thrustmaster Quick Release (15) device’s
ring anticlockwise, while holding the racing wheel (2) in position.
Then, tighten the ring as much as you can: to do so, hold the ring in position and rotate the racing wheel
clockwise.
Once you have installed the wheel, rotate it 180° (when facing the wheel, the Sparco logo should be
upside down) to access the small attachment screw located on the ring of the Thrustmaster Quick
Release (15) device. Use a large Phillips screwdriver to tighten the small attachment screw (do not use
excessive force), turning it clockwise.
When using a Philips screwdriver, ensure NOT to use excessive force
when tightening the small attachment screw!
Stop turning the screw as soon as you feel some resistance.
8/22
ATTACHING THE RACING WHEEL
WARNING:
damage the racing wheel).
Attaching the racing wheel’s base to a cockpit
1. Place the racing wheel’s base on the cockpit shelf.
2. Drive two M6 screws (not included) through the cockpit shelf, then feed them into the two small
screw threads located on the underside of the racing wheel.
Important: The length of the two M6 screws must not exceed the thickness of the shelf + 12 mm;
longer screws could cause damage to internal components located in the racing wheel’s base.
3. If required, tighten the standard attachment system by inserting the fastening screw in the large
threaded hole.
Attaching the racing wheel to a table or a desktop
1. Place the racing wheel on a table or any other horizontal, flat and stable surface.
2. Insert the fastening screw (9) in the attachment system (8), then tighten the device by turning the
screw anticlockwise, so that it feeds into the large threaded hole (7) located beneath the racing
wheel, until the wheel is perfectly stable.
ALWAYS NEVER
- Never tighten the screw alone, without the attachment system in place (this could
9/22
ATTACHMENT /
REMOVAL
To tighten:
Turn the screw
anticlockwise
DIRECTION
To release:
Turn the screw
clockwise
10/22
INSTALLATION ON XBOX ONE
1. Connect the pedal set to the connector (18) located at the back of the racing wheel's base.
2. Connect the TURBO POWER power supply cable (20) to the connector (16) located at the back of
the racing wheel's base.
3. Connect the removable power supply cable (21) to the TURBO POWER power supply (20).
4. Connect the removable power supply cable (21) to a mains outlet with proper voltage
specifications.
5. Connect the removable racing wheel's USB connector (22) to the racing wheel's connector (17) and
to one of the console's USB ports.
6. When you turn on your console, the racing wheel automatically self-calibrates.
You are now ready to race!
The list of Xbox One games compatible with the TS-XW RACER is availab le here:
http://support.thrustmaster.com (in the Racing Wheels / TS-XW RACER section).
This list is updated regularly.
XBOX ONE MAPPING
11/22
INSTALLATION ON PC
1. Go to http://support.thrustmaster.com, then select Racing Wheels / TS-XW RACER to
download the drivers and the force feedback software for PC.
2. Once the download is complete, launch the installation, and follow the on-screen instructions to
connect the wheel’s USB plug to your computer and complete the installation.
3. Once the installation is complete, click Finish and restart your computer.
4. Select Start / All Programs / Thrustmaster / FFB Racing Wheel / Control Panel to open the Game
Controllers window.
The Game Controllers window displays the racing wheel’s name Thrustmaster TS-XW RACER with
the status OK.
5. Click Properties to configure your wheel in the TS- XW RACER control panel:
• Test Input tab: allows to test and view the action buttons, directional buttons, wheel and pedals
axes, and to adjust the wheel’s rotation angle in your PC games.
• Test Forces tab: allows to test 12 force feedback effects.
• Gain Settings tab: allows to adjust the power of the force feedback effects in your PC games.
You are now ready to play!
General notes:
- On PC, click OK to close the Game Controllers window before launching the game.
- Your wheel’s firmware version is displayed in the upper right-hand corner of the control panel tabs.
PC MAPPING
12/22
UPDATING YOUR RACING WHEEL’S FIRMWARE
GAS AND CLUTCH PEDALS
Color of the MODE indicator light (6)
NORMAL
RED
SWAPPED AROUND
GREEN
The firmware included in your racing wheel’s base can be updated to a more recent version featuring
product enhancements.
To display the firmware version that your racing wheel is currently using and update it if required: on
PC, visit http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, then select
Firmware and follow the instructions describing the download and installation procedure.
AUTOMATIC RACING WHEEL CALIBRATION
The wheel automatically self-calibrates when you plug the racing wheel into an electrical outlet and
connect the racing wheel’s USB connector.
During this phase, the racing wheel will rotate quickly towards the left and the right, covering a 1080
degree angle, before stopping at the center.
Never touch the racing wheel during the self-calibration phase!
If your racing wheel does not function correctly, or if it seems to be improperly calibrated:
Power off your PC or your console and completely disconnect the racing wheel. Then reconnect all
cables (including the power supply cable and the pedal set), and restart your PC and your game.
(This could result in improper calibration and/or personal injuries.)
WARNING:
INTERNAL COOLING SYSTEM FOR THE WHEEL’S BASE
The internal cooling system for the wheel’s base
- starts working when the wheel is powered on.
- switches off after a few minutes of inactivity when the internal temperature cools down to a low level.
- switches on again when you use the wheel.
MODE BUTTON AND INDICATOR LIGHT (6)
MODE button for the pedal set
You can electronically swap the accelerator and clutch pedals if you are using a Thrustmaster T3PA or
T3PA-PRO pedal set connected to the connector for pedal set (18).
To do so, simply press the MODE button (6) for 2 seconds.
The racing wheel’s internal memory stores whether the pedals have been swapped around or not.
Other information regarding the MODE button
To learn more about the MODE button and indicator light, please visit
http://support.thrustmaster.com. Click Racing Wheels / TS-XW RACER, and then select Manual or
FAQ.
13/22
1 Metal support for conical stop
3 Attachment screw for metal support
4 2.5 mm Allen key (included)
6 Pedal arm
8 Metal pedal head
TECHNICAL FEATURES
(not installed by default)
2 Conical stop
5 Position adjustment nut for conical stop
7 Plastic head support
14/22
WARNING
NEVER
NEVER
NEVER
Before using this product, be sure to read these instructions carefully and save them for future reference.
For safety reasons, never use the pedal set with bare feet or while wearing
THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF
INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES.
Warning – Pedal set pinching hazard during gaming sessions
* Keep the pedal set out of the reach of children.
* During gaming sessions, never place your fingers or thumbs on or near the sides of the pedals.
* During gaming sessions, never place your fingers or thumbs on or near the rear base of the pedals.
* During gaming sessions, never place your fingers or thumbs on or near the front base of the pedals.
only socks on your feet.
15/22
AUTOMATIC CALIBRATION OF PEDALS
- Never connect or disconnect the pedal set from the base of the wheel when the wheel is
connected to the system or PC, or during gaming sessions, to avoid calibration problems.
= Always connect the pedal set to the wheel before connecting the wheel to the system or PC.
- Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate
themselves after being pressed a few times.
- Never press on the pedals when the wheel is self-calibrating or when your game is starting up, to
avoid calibration problems.
- If the pedals are not functioning correctly or appear to be improperly calibrated, power off your
system, completely disconnect your wheel, then reconnect all of the cables (including the power
supply cable and the pedal set cable), power the system back on and restart your game.
IMPORTANT:
ATTACHING THE PEDAL SET TO A COCKPIT
- Attach the pedal set using the small screw threads located on the underside of the pedal set.
- Screw two M6 screws (not included) into the cockpit’s pedal support plate and into the two small
screw threads located on the underside of the pedal set.
Important: The length of the two M6 screws must not exceed the thickness of the cockpit’s pedal
support plate plus an additional 10 mm, to avoid damaging the pedal set’s internal components.
16/22
ADJUSTING THE PEDAL SET
Low position (default)
High position
Each of the three pedals includes:
- A metal head (8) with multiple perforations (nine for the accelerator – six for the brake – six for the
clutch).
- A plastic head support (7) (placed between the head and the arm) with four perforations.
- A pedal arm (6) with two perforations.
ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s
USB cable from the system or PC before making any adjustments to your pedal set.
Adjusting the HEIGHT of the accelerator pedal
- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and
its support ( 7) in place.
- Select your preferred height position, then replace and re-tighten the screws so that the metal
head (8) and its support (7) are held firmly in place.
17/22
Adjusting the SPACING of the three pedals
- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and
its support ( 7) in place.
- Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the
screws so that the metal head (8) and its support (7) are held firmly in place.
Examples illustrating the brake pedal:
Left position Centered position (default) Right position
Number of possible spacing positions per pedal:
- Three for accelerator pedal
- Three for brake pedal
- Three for clutch pedal
Adjusting the INCLINATION of the pedals
- Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and
its support ( 7) in place.
- Turn the plastic head support ( 7) 180°, then replace and re-tighten the screws so that the metal
head (8) and its support (7) are held firmly in place.
Examples illustrating the accelerator pedal:
Less inclined position More inclined position (default)
Number of possible inclination positions per pedal:
- Two for accelerator pedal
- Two for brake pedal
- Two for clutch pedal
18/22
Installing the conical stop (“CONICAL RUBBER BRAKE” mod)
This modification (or “mod”) is not essential, and is not installed by default. This means that the
brake pedal functions perfectly even if the m od is not installed.
This mod lets you experience a different feeling and resistance when braking.
It’s up to you whether or not to install it, depending on your own preferences.
- Screw the conical stop (2) onto its metal support (1).
- Screw the position adjustment nut (5) onto the bottom (onto the conical stop’s screw thread).
- Position the unit at the back of the brake pedal’s arm.
19/22
- Using the included 2.5 mm Allen key (4), attach the unit using the attachment screw (3) and the
small central screw thread located on the underside of the pedal set.
The “CONICAL RUBBER BRAKE” mod is now installed!
Adjusting the brake pedal’s RANGE of travel and STRENGTH of resistance
By slightly unscrewing the nut (5), you can further strengthen the resistance of the brake pedal by
moving the conical stop (2) closer to the back of the pedal’s arm (if necessary, use a 14 mm wrench
or pliers to re-tighten the nut and maintain the selected position). The closer the conical stop is
positioned to the back of the pedal’s arm, the greater the strength of resistance will be.
Note: When the conical stop is very close to the back of the brake pedal’s arm, you may experience
difficulties in reaching the maximum calibration value. Should that be the case:
* Slowly, press very hard on the brake pedal so as to reach the maximum value (if necessary, stand
very briefly on the pedal – just for a second), then release the pressure; or else
* Move the conical stop a bit farther away from the back of the brake pedal’s arm.
20/22
CONSUMER WARRANTY INFORMATION
Worldwide, Guillemot Corporation S.A., whose registered office is located at Place du Granier, B.P. 97143, 35571
Chantepie, France (hereinafter “Guillemot”) warrants to the consumer that this Thrustmaster product shall be free
from defects in materials and workmanship, for a warranty period which corresponds to the time limit to bring an
action for conformity with respect to this product. In the countries of the European Union, this corresponds to a
period of two (2) years from delivery of the Thrustmaster product. In other countries, the warranty period
corresponds to the time limit to bring an action for conformity with respect to the Thrustmaster product according to
applicable laws of the country in which the consumer was domiciled on the date of purchase of the Thrustmaster
product (if no such action exists in the corresponding country, then the warranty period shall be one (1) year from the
original date of purchase of the Thrustmaster product).
Notwithstanding the above, rechargeable batteries are covered by a warranty period of six (6) months from the date
of original purchase.
Should the product appear to be defective during the warranty period, immediately contact Technical Support, who
will indicate the procedure to follow. If the defect is confirmed, the product must be returned to its place of purchase
(or any other location indicated by Technical Support).
Within the context of this warranty, the consumer’s defective product shall, at Technical Support’s option, be either
replaced or returned to working order. If, during the warranty period, the Thrustmaster product is subject to such
reconditioning, any period of at least seven (7) days during which the product is out of use shall be added to the
remaining warranty period (this period runs from the date of the consumer’s request for intervention or from the date
on which the product in question is made available for reconditioning, if the date on which the product is made
available for reconditioning is subsequent to the date of the request for intervention). If permitted under applicable
law, the full liability of Guillemot and its subsidiaries (including for consequential damages) is limited to the return to
working order or the replacement of the Thrustmaster product. If permitted under applicable law, Guillemot disclaims
all warranties of merchantability or fitness for a particular purpose.
This warranty shall not apply: (1) if the product has been modified, opened, altered, or has suffered damage as a
result of inappropriate or abusive use, negligence, an accident, normal wear, or any other cause unrelated to a
material or manufacturing defect (including, but not limited to, combining the Thrustmaster product with any
unsuitable element, including in particular power supplies, rechargeable batteries, chargers, or any other elements
not supplied by Guillemot for this product); (2) if the product has been used for any use other than home use,
including for professional or commercial purposes (game rooms, training, competitions, for example); (3) in the event
of failure to comply with the instructions provided by Technical Support; (4) to software, said software being subject
to a specific warranty; (5) to consumables (elements to be replaced over the product’s lifespan: disposable batteries,
audio headset or headphone ear pads, for example); (6) to accessories (cables, cases, pouches, bags, wrist-strap s,
for example); (7) if the product was sold at public auction.
This warranty is nontransferable.
The consumer’s legal rights with respect to laws applicable to the sale of consumer goods in his or her country are
not affected by this warranty.
Additional warranty provisions
During the warranty period, Guillemot shall not provide, in principle, any spare parts, as Technical Support is the only
party authorized to open and/or recondition any Thrustmaster product (with the exception of any reconditioning
procedures which Technical Support may request that the consumer carry out, by way of written instructions – for
example, due to the simplicity and the lack of confidentiality of the reconditioning process – and by providing the
consumer with the required spare part(s), where applicable).
Given its innovation cycles and in order to protect its know-how and trade secrets, Guillemot shall not provide, in principle,
any reconditioning notification or spare parts for any Thrustmaster product whose warranty period has expired.
In the United States of America and in Canada, this warranty is limited to the product’s internal mechanism and
external housing. In no event shall Guillemot or its affiliates be held liable to any third party for any consequential or
incidental damages resulting from the breach of any express or implied warranties. Some States/Provinces do not
allow limitation on how long an implied warranty lasts or exclusion or limitation of liability for consequential or
incidental damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from State to State or Province to Province.
21/22
TECHNICAL SUPPORT
http://support.thrustmaster.com
Liability
If permitted under applicable law, Guillemot Corporation S.A. (hereinafter “Guillemot”) and its subsidiaries disclaim all
liability for any damages caused by one or more of the following: (1) the product has been modified, opened or
altered; (2) failure to comply with assembly instructions; (3) inappropriate or abusive use, negligence, an accident (an
impact, for example); (4) normal wear; (5) the use of the product for any use other than home use, including for
professional or commercial purposes (game rooms, training, competitions, for example). If permitted under applicable
law, Guillemot and its subsidiaries disclaim all liability for any damages unrelated to a material or manufacturing
defect with respect to the product (including, but not limited to, any damages caused directly or indirectly by any
software, or by combining the Thrustmaster product with any unsuitable element, including in particular power
supplies, rechargeable batteries, chargers, or any other elements not supplied by Guillemot for this product).
DECLARATION OF CONFORMITY
CANADIAN COMPLIANCE NOTICE: this Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
USA COMPLIANCE NOTICE: this equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
22/22
COPYRIGHT
*
*
© 2017 Guillemot Corporation S.A. All rights reserved. Thrustmaster® is a registered trademark of
Guillemot Corporation S.A. All other trademarks are the property of their respective owners.
Illustrations not binding. Contents, designs and specifications are subject to change without notice and
may vary from one country to another. Made in China.
Manufactured and distributed by Guillemot Corporation S.A. under official licence from Sparco S.p.A.
Sparco is a registered trademark of Sparco S.p.A.
ENVIRONMENTAL PROTECTION RECOMMENDATION
In the European Union: At the end of its working life, this product should not be
disposed of with standard household waste, but rather dropped off at a collection
point for the disposal of Waste Electrical and Electronic Equipment (WEEE) for
recycling.
This is confirmed by the symbol found on the product, user manual or packaging.
Depending on their characteristics, the materials may be recycled. Through
recycling and other forms of processing Waste Electrical and Electronic
Equipment, you can make a significant contribution towards helping to protect the
environment.
Please contact your local authorities for information on the collection point nearest you.
For all other countries: Please adhere to local recycling laws for electrical and electronic equipment.
Retain this information. Colours and decorations may vary.
Plastic fasteners and adhesives should be removed from the product before it is used.
www.thrustmaster.com
*Applicable to EU and T urkey only
1/22
Pour Xbox One et Windows
Manuel de l’utilisateur
2/22
CARACTERISTIQUES TECHNIQUES
1 Base
5 Bouton Guide Xbox + voyant lumineux blanc
6 Bouton MODE + voyant lumineux rouge/vert
2 Roue
3 2 palettes séquentielles de changement de
vitesse (up & down)
4 Croix multidirectionnelle avec bouton
poussoir
7 Gros pas de vis (pour le système de fixation
et la vis de serrage)
8 Système de fixation
9 Vis de serrage métallique
3/22
15 Thrustmaster Quick Release
18 Connecteur de pédalier
19 Connecteur pour la boîte de vitesses TH8A
22 Câble USB amovible
16 Connecteur pour le bloc d’alimentation
TURBO POWER
17 Connecteur pour le câble USB amovible
RELIER LE VOLANT AU SECTEUR = A LIRE IMPERATIVEMENT!
Ne reliez jamais le bloc d’alimentation TURBO POWER à une prise de courant dont le
voltage est différent ! Le voltage du TURBO POWER est indiqué sur l’étiquette située au-dessus du
connecteur femelle du câble d’alimentation.
Ne branchez jamais un bloc d’alimentation autre que le TURBO POWER sur la base du TS-
XW RACER, même si le connecteur est compatible ! Par exemple, ne branchez jamais l’adaptateur
secteur du volant T500 RS sur la base du TS- XW RACER.
(boîte de vitesses vendue séparément)
20 Bloc d’alimentation TURBO POWER
21 Câble d’alimentation secteur
4/22
AVERTISSEMENTS
Avant d’utiliser ce produit, lisez attentivement cette documentation et conservez-la pour pouvoir la
consulter ultérieurement.
Avertissement – Choc électrique
* Conservez le produit dans un endroit sec et ne l’exposez ni à la poussière ni au soleil.
* Ne tordez pas et ne tirez pas sur les connecteurs et câbles.
* Ne renversez pas de liquide sur le produit et ses connecteurs.
* Ne mettez pas le produit en court-circuit.
* Ne démontez jamais le produit, ne le jetez pas au feu et ne l’exposez pas à des températures élevées.
* N’utilisez pas de câble d’alimentation autre que celui fourni avec votre volant.
* N’utilisez pas le câble d’alimentation secteur si celui-ci où ses connecteurs sont endommagés, fendus
ou cassés.
* Assurez-vous que le câble d’alimentation secteur est parfaitement inséré dans la prise murale et dans
son connecteur situé à l’arrière de la base du volant.
* N’ouvrez pas l’appareil. L’appareil ne contient pas de pièces réparables par l'utilisateur. Confiez toute
réparation au fabricant, à une agence spécifiée ou un technicien qualifié.
* Utilisez uniquement les systèmes de fixation /accessoires spécifiés par le fabricant.
* Si le volant fonctionne de manière anormale (s’il émet des sons, de la chaleur ou des odeurs
anormales), arrêtez immédiatement de l’utiliser, débranchez le câble d’alimentation de la prise
électrique et déconnectez les autres câbles.
* Lorsque vous n’utilisez pas le volant pendant une période prolongée, débranchez le câble
d’alimentation secteur de la prise électrique.
* La prise électrique doit être située à proximité de l’équipement et doit être facilement accessible.
Grilles d’aération
Veillez à n’obstruer aucune grille d’aération de la base du volant. Pour assurer une ventilation optimale,
respectez les points ci-après :
* Placez la base à 10 cm au moins d’une surface murale.
* Ne placez pas la base dans un endroit exigu.
* Ne couvrez pas la base.
* Ne laissez pas la poussière s’accumuler sur les grilles d’aération.
Pour des raisons de sécurité, ne jouez pas pieds nus ou en chaussettes
THRUSTMASTER® DECLINE TOUTE RESPONSABILITE EN CAS DE
BLESSURE SUITE A UNE UTILISATION DU PEDALIER SANS CHAUSSURES.
Avertissement – Blessures dues au retour de force et aux mouvements répétitifs
Jouer avec un volant à retour de force peut causer des douleurs aux muscles et aux articulations. Afin
d’éviter tout problème :
* Evitez les périodes trop longues de jeu.
* Faites une pause de 10 à 15 minutes après chaque heure de jeu.
* Si vous éprouvez fatigue ou douleur au niveau des mains, des poignets, des bras, des pieds ou des
jambes, cessez de jouer et reposez-vous pendant quelques heures avant de recommencer à jouer.
lorsque vous utilisez le pédalier.
5/22
personnes âgées de 16 ans ou plus
une autre personne
Avertissement – Blessures dues au retour de force et aux mouvements répétitifs (suite)
* Si les symptômes ou les douleurs indiqués ci-dessus persistent lorsque vous reprenez le jeu, arrêtez
de jouer et consultez votre médecin.
* Laissez hors de portée des enfants.
* Lors des phases de jeu, laissez toujours vos deux mains correctement positionnées sur le volant
sans jamais le lâcher complètement.
* Lors des phases de jeu, ne placez jamais vos mains ou vos doigts sous les pédales ou à proximité
du pédalier.
* Lors des phases de calibration et de jeu, ne jamais introduire une main ou un bras à l’intérieur de la
roue du volant.
* Vérifiez que la base du volant est correctement fixée, conformément aux instructions du manuel .
PRODUIT LOURD
Produit à manipuler uniquement par des
Ne pas laisser tomber le produit sur vous ou
TOUJOURS
6/22
COMPATIBILITÉ AVEC L’ÉCOSYSTÈME THRUSTMASTER
Pédaliers
La base du TS-XW RACER est compatible :
- Sur Xbox One et Windows, avec les pédaliers Thrustmaster T3PA et T3PA-PRO qui se branchent
directement sur le connecteur de pédalier (18) de la base.
- Sous Windows, avec l’adaptateur Thrustmaster DB9 PEDALS T.RJ12 ADAPTER qui permet aux
pédaliers non-Thrustmaster équipés d’un connecteur DB9 de se brancher directement sur le connecteur
de pédalier (18) de la base.
- Sous Windows (uniquement) avec tous les pédaliers USB du marché (dans les jeux acceptant le
multi-USB et les pédaliers USB).
Roues
La base du TS-XW RACER est compatible sur Xbox One et Windows avec toutes les roues détachables
Thrustmaster, par exemple :
- Ferrari 599XX EVO 30 Wheel Add-On Alcantara Edition
- Ferrari F1 Wheel Add-On
- Ferrari GTE Wheel Add-On Ferrari 458 Challenge Edition
- TM Leather 28 GT Wheel Add-On
- TM Open Wheel Add-On
- TM Competition Wheel Sparco® P310 Mod
- TM Rally Wheel Add-On Sparco® R383 Mod
- etc.
Boîtes de vitesses
La base du TS-XW RACER est compatible :
- sur Xbox One, avec la boîte de vitesses Thrustmaster TH8A Shifter Add-On en la branchant
directement sur le connecteur de boîte de vitesses (19) de la base pour les modes « Séquentiel (+/-) » et
« H (7+1) »
- sous Windows, avec la boîte de vitesses Thrustmaster TH8A Shifter Add-On en la branchant
directement sur le connecteur de boîte de vitesses (19) de la base pour le mode « Séquentiel (+/-) »
- sous Windows avec la boîte de vitesses Thrustmaster TH8A Shifter Add-On en la branchant en USB
pour les modes « Séquentiel (+/-) », « H (7+1) » et ANALOG / FREIN A MAIN
- sous Windows, avec toutes les boîtes de vitesses USB du marché (dans les jeux acceptant le multiUSB et les boîtes de vitesses USB).
AIDES & FAQ DIVERSES (non notifiées dans ce manuel)
Allez sur http://support.thrustmaster.com. Cliquez sur Volants / TS-XW RACER puis Manuel
utilisateur ou FAQ.
7/22
INSTALLATION DE LA ROUE SUR SA BASE
Alignez la position des connecteurs en vous aidant des flèches :
Connecteur de la base (1): Flèche vers le haut
Connecteur de la roue (2): Flèche vers le haut
Une fois les connecteurs mis en place, il vous suffit de tourner la bague du Thrustmaster Quick Release
(15) dans le sens inverse des aiguilles d’une montre tout en maintenant la roue (2) fixe.
Puis serrez fortement (et au maximum) la bague en la maintenant fixe et en tournant le volant dans le
sens des aiguilles d’une montre.
Lorsque la roue est installée, tournez-la de 180° (vu de face, le Logo Sparco doit être à l’envers) afin
d’accéder à la petite vis de fixation située sur la bague du Thrustmaster Quick Release (15). A l’aide d’un
gros tournevis cruciforme, vissez sans forcer la petite vis de fixation dans le sens des aiguilles d’une
montre.
Lorsque vous revissez la petite vis de fixation à l’aide d’un tournevis cruciforme,
NE FORCEZ PAS.
Arrêtez de visser dès que vous sentez une résistance.
Loading...