Texas Instruments TL750L05QP, TL750L05QLP, TL750L05QKC, TL750L05CLPM, TL750L05CLP Datasheet

...

TL750L, TL751L SERIES

LOW-DROPOUT VOLTAGE REGULATORS

SLVS017I – SEPTEMBER 1987 – REVISED JULY 1999

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Very Low Dropout Voltage, Less Than 0.6 V at 150 mA

Very Low Quiescent Current

TTL- and CMOS-Compatible Enable on TL751L Series

60-V Load-Dump Protection

Reverse Transient Protection Down to –50 V

Internal Thermal-Overload Protection

Overvoltage Protection

Internal Overcurrent-Limiting Circuitry

Less Than 500-µA Disable (TL751L Series)

DEVICE

COMPONENT

COUNT

Transistors 20 JFETs 2 Diodes 5 Resistors 16

description

The TL750L and TL751L series are low-dropout positive-voltage regulators specifically designed for battery-powered systems. These devices incorporate overvoltage and current-limiting protection circuitry, along with internal reverse-battery protection circuitry to protect the devices and the regulated system. The series is fully protected against 60-V load-dump and reverse-battery conditions. Extremely low quiescent current during full-load conditions makes these devices ideal for standby power systems.

The TL750L and TL751L series of fixed-output voltage regulators offers 5-V, 8-V , 10-V, and 12-V options. The TL751L series has the addition of an enable (ENABLE

) input. When ENABLE is high, the regulator output is placed in the high-impedance state. This gives the designer complete control over power up, power down, or emergency shutdown.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

OUTPUT

NC NC NC

INPUT NC COMMON NC

8 7 6 5

OUTPUT COMMON COMMON

INPUT COMMON COMMON NC

TL750L ...D PACKAGE

(TOP VIEW)

The common terminal is in electrical contact with the mounting base.

TO-226AA

TL750L . . . KC PACKAGE

(TOP VIEW)

TL750L . . . LP PACKAGE

(TOP VIEW)

OUTPUT COMMON COMMON

INPUT COMMON COMMON ENABLE

OUTPUT

NC NC NC

INPUT NC COMMON ENABLE

TL750L ...P PACKAGE

(TOP VIEW)

TL751L ...D PACKAGE

(TOP VIEW)

TL751L ...P PACKAGE

(TOP VIEW)

TO-220AB

1 2 3 4

8 7 6 5

1 2 3 4

8 7 6 5

1 2 3 4

8 7 6 5

1 2 3 4

OUTPUT COMMON INPUT

INPUT COMMON OUTPUT

NC – No internal connection

TL750L, TL751L SERIES LOW-DROPOUT VOLTAGE REGULATORS

SLVS017I – SEPTEMBER 1987 – REVISED JULY 1999

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

description (continued)

The TL750LxxC and the TL751LxxC series are characterized for operation over the virtual junction temperature range of 0°C to 125°C . The TL750L05Q and TL751L05Q are characterized for operation over the virtual junction temperature range of –40°C to 125°C.

AVAILABLE OPTIONS

PACKAGED DEVICES

TYP

25°C

SMALL

OUTLINE

(D)

HEAT-SINK

MOUNTED

(KC)

PLASTIC

CYLINDRICAL

(LP)

PLASTIC

DIP

(P)

CHIP

FORM

(Y)

5 V

TL750L05CD TL751L05CD

TL750L05CKC TL750L05CLP

TL750L05CP TL751L05CP

TL750L05Y

8 V

TL750L08CD TL751L08CD

TL750L08CKC TL750L08CLP

TL750L08CP TL751L08CP

TL750L08Y

0°C to 125°C

10 V

TL750L10CD TL751L10CD

TL750L10CKC TL750L10CLP

TL750L10CP TL751L10CP

TL750L10Y

12 V

TL750L12CD TL751L12CD

TL750L12CKC TL750L12CLP

TL750L12CP TL751L12CP

TL750L12Y

–40°C to 125°C 5 V

TL750L05QD TL751L05QD

– – – –

The D, KTE, and LP packages are available taped and reeled. The KTP is only available taped and reeled. Add R suffix to device type (e.g., TL750L05CDR). Chip forms are tested at 25°C.

absolute maximum ratings over operating junction temperature range (unless otherwise noted)

†

TL750Lxx TL751Lxx

UNIT

Continuous input voltage 26 V Transient input voltage, TA = 25°C (see Note 1) 60 V Continuous reverse input voltage –15 V Transient reverse input voltage: t ≤ 100 ms –50 V

D package 97

KC package 22

Package thermal impedance, θ

(see Notes 2 and 3)

LP package 156

°C

P package 127

Virtual junction temperature range, T

–40 to 150 °C Lead temperature 1,6 mm (1/16 inch) for 10 seconds 260 °C Storage temperature range, T

stg

–65 to 150 °C

†

Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. The transient input voltage rating applies to the waveform shown in Figure 1.

2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can impact reliability.

3. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace length of zero.

TL750L, TL751L SERIES

LOW-DROPOUT VOLTAGE REGULATORS

SLVS017I – SEPTEMBER 1987 – REVISED JULY 1999

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

recommended operating conditions over recommended operating junction temperature range (unless otherwise noted)

MIN MAX UNITS

TL75xL05 6 26

TL75xL08 9 26

Input voltage, V

TL75xL10 11 26

TL75xL12 13 26

High-level ENABLE input voltage, V

TL751Lxx 2 15 V

TA = 25°C TL751Lxx –0.3 0.8

ow-level

ENABLE i

nput voltage,

†

TA = full range‡TL751Lxx –0.15 0.8

Output current range, I

TL75xLxx 0 150 mA

TL75xLxxC 0 125

Operating virtual junction temperature, T

TL75xL05Q –40 125

°C

†

The algebraic convention, in which the least positive (most negative) value is designated minimum, is used in this data sheet for ENABLE voltage levels and temperature only.

‡

Full range is 0°C to 125°C for the TL75xLxxC devices, and –40°C to 125°C for the TL75L05Q devices.

electrical characteristics, V

= 14 V, I

= 10 mA, TJ = 25°C (unless otherwise noted) (see Note 4)

PARAMETER

TEST CONDITIONS

TL750L05 TL751L05

UNIT

MIN TYP MAX

4.80 5 5.2

Output voltage

TJ = TJ(min) to 125°C

4.75 5.25

VI = 9 V to 16 V 5 10

Input regulation voltage

VI = 6 V to 26 V 6 30

Ripple rejection VI = 8 V to 18 V, f = 120 Hz 60 65 dB Output regulation voltage IO = 5 mA to 150 mA 20 50 mV

IO = 10 mA 0.2

Dropout voltage

IO = 150 mA 0.6

Output noise voltage f = 10 Hz to 100 kHz 500 µV

IO = 150 mA 10 12

Input bias current

VI = 6 V to 26 V, IO = 10 mA, TJ = TJ(min) to 125°C

1 2

ENABLE > 2 V

0.5

Pulse-testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.1-µF capacitor across the input and a 10-µF capacitor , with equivalent series resistance of less than 0.4 Ω, across the output.

TJ(min) is 0°C for the TL75xLxxC devices, and –40°C for the TL75xLxxQ devices.

NOTE 4: For TL750L05Q/TL751L05Q, all characteristics are measured with a 0.1-µF tantalum capacitor on the output with equivalent series

resistance within the guidelines shown in Figure 4.

+ 6 hidden pages