Telefunken TF-1549 User manual

Instruction manual

Руководство по эксплуатации

RADIO WITH ALARM / РАДИОПРИЁМНИК C БУДИЛЬНИКОМ

TF-1549

Instruction manual

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in future.

Description

Front panel

1. BAND button

2. TEMP/ button

3. Y-M-D/ button

4. AL.1 button

5. SNOOZE/SLEEP button

6. AL.2 button

7. AL.SET button

8. MODE button

9. button

10. Display

11. VOLUME regulator

12. TUNE regulator

Not indicated: power cord (back panel), FM antenna (back panel), temperature sensor (back panel), infrared sensor (top panel), line input (top panel), battery compartment (bottom), DIMMER switch (top panel), RESET button hole (back panel), LIGHT ON/OFF button (back panel).

Right panel

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

1 2 3 4 5 6 7 8 9 10

Instruction manual

Important safeguards

• The instruction manual contains important operating and maintenance instructions. For your safety, it is necessary to refer the manual. Keep the manual for use in future.

• Do not hit or drop the unit.

• Do not expose the unit to vibration, direct sunlight, too high or low temperature or humidity.

• If you are not going to use the unit within a long period of time, remove the batteries to avoid their leakage.

• Do not disassemble the unit yourselves. Refer servicing to qualified service personnel.

Power supply

Battery operation

• Insert 1 x 3 V lithium battery CR2032 (not included) to the terminal inside the battery compartment according to the polarity marks (+ and -). Your set will not work normally from the battery supply, but there is now the advantage that, in case there is a mains current failure, your clock will continue to work. The clock display will not light up, the clock time and alarm setting will be held in the clock memory by the battery back-up system.

This enables you to move the set from place to place without re-setting the clock every time. The battery back-up system is only meant to be used from short temporary power failures. For longer durations the battery may become exhausted or there may be some deviation in accuracy.

• When the battery is exhausted, it should be removed from the set to prevent leakage. If you do not wish to take advantage of the battery back-up system, your set will work normally without a battery. However, if disconnected from the mains, the clock figures will flash when the mains are reconnected and you must re-set the clock.

AС operation

• The appliance is for household use only.

• Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home.

• Insert the plug into the power supply.

• The set is now working as electronic clock.

General operations

Setting the clock and calendar

• Press and hold MODE button. Press it repeatedly to cycle through time and calendar settings in following order: Year => Month => Day => 12/24H mode => Current hours => Current minutes. The selected setting will blink.

• Press repeatedly TEMP/ button or press and hold it to decrease the setting; press repeatedly Y-M-D/ button or press and hold it to increase the setting.

• In normal mode, press repeatedly Y-M-D/

button to switch the display between current time, year and month and day. Each indication will be on for 5 seconds, then the display returns to initial mode.

Dimmer function

To adjust brightness of display, slide

DIMMER switch to HIGH or LOW position.

Reset

To reset all settings of the unit to default settings, press the RESET hole with a pointed object (e.g., a ballpoint pen). This measure is needed when you changed the batteries in the unit or if the unit does not function correctly.

Daylight saving time

Press and hold Y-M-D/ button to switch on or off the DST (Daylight Saving Time) mode. This enables to observe 1-hour difference between summer and winter time.

Thermometer

Press TEMP/ button to show the current

Instruction manual

activated. The radio will turn off automatically after the preset time period elapses.

• To cancel the sleep function, press

button.

Alarm operation

Setting the alarm

• Press and hold AL.SET button. Press it repeatedly to cycle through alarm settings in following order: Alarm 1 hours => Alarm 1 minutes => Alarm 1 weekend => Alarm 2 hours => Alarm 2 minutes => Alarm 2 weekend. The selected setting will blink.

• Press repeatedly TEMP/ button or press and hold it to decrease the setting; press repeatedly Y-M-D/ button or press and hold it to increase the setting.

• In normal mode, press repeatedly AL.SET button to show the alarm settings.

• Slide DIMMER switch to AUTO OFF position. After 15 seconds the display will switch off and it will resume when the preset alarm time comes.

Alarm signal selection

Press repeatedly AL.1 button (for Alarm 1) or AL.2 button (for Alarm 2) to select alarm sound. Press once to select buzzer ( will be on), press twice to select radio ( will be on), press thrice to disable alarm signal (no indication will be on).

Snooze control

• When the alarm time comes, the signal will sound for 30 minutes if no button is pressed. After that the sound will mute and start at the same time the following day.

• When the alarm is on, press SNOOZE/ SLEEP button to interrupt the alarm signal. After 9 minutes the alarm will be on again.

• If you want to stop the alarm, press button. The alarm will resume in 24 hours.

temperature. The temerature indicatoin will be on for 5 seconds, then the display returns to initial mode. Press and hold TEMP/ button to switch between Celsius and Fahrenheit temperature modes.

Bottom backlight

To switch on/off the backlight of the unit bottom, press LIGHT ON/OFF button.

Line input

• You can connect the audio output of an external device to this unit, to listen to the sound of that device through the amplifier of this unit.

• To connect an external audio device (eg. MP3 player), please use a standard stereo cable (not included) with 3.5 mm to 3.5 mm plugs to connect the headphone out or audio line-out of the external device to the Line input socket of this unit.

Radio operation

Tuner operations

• Press button to turn the radio on or off.

• Press BAND button to switch between AM and FM radio bands.

• Adjust the program by rotating TUNE regulator. Use VOLUME regulator to adjust volume level.

• To obtain better FM signal reception, extend the FM wire antenna to its full length.

• The AM signal is picked up through the built-in antenna. The unit should be placed to a position for the best reception.

Sleep to music

• In Radio mode, press SNOOZE/SLEEP button to turn on sleep mode. The default sleep time of 90 minutes will be set. Press this button repeatedly to select 60, 30 or 15 minutes of sleep time period. The figures will blink on the display for 5 seconds. “SLEEP” will be displayed meaning that the sleep function is

+ 7 hidden pages