- Data Brochure
0 – 135 Ω Converter 005
The tekmar 0 – 135 Ω Converter 005 allows for the signal conversion of a 4 – 20 mA input signal from a control to a
0 – 135 Ω output signal. The 005 allows for conduit to directly attach to the enclosure. The 005 enclosure is flameretardant and can withstand high temperatures.
Installation
D 005
04/09
STEP ONE
—
GETTING READY
———
• Check the contents of this package. If any of the contents listed are missing or damaged, please contact your wholesaler or
tekmar sales representative for assistance.
• Type 005 includes: One 0 – 135 Ω Converter 005 and Data Brochure D 005.
STEP TWO
—
MOUNTING THE CONVERTER BASE
———
• Remove the screw and pull the front cover off the converter
enclosure.
• The 005 can either be mounted directly on a wall or on a 2” x 4”
electrical box. When the 005 is wall mounted, the wiring should enter
through the knockout on the bottom of the enclosure.
• The 005 should be located in a position such that it will not be
accidentally damaged.
STEP THREE
—
———
WIRING
• All electrical wiring terminates in the 005 enclosure. The back and
bottom have standard 7/8” (22 mm) knockouts that accept common
wiring hardware and conduit fittings.
• The 005 has two separate converter circuits. One is for Modutrol IV™
gas valve actuating motors and the other is for V9055™ gas valve
Modutrol IV™
0 - 135 Ω
Actuating
Motor
005 bottom
entry wiring
6
Mod 1 mA
+
B
R
W
7
–
Modutrol IV
tekmar
B
R
W
+
-
005 mounted
onto 2" x 4"
electrical box
V9055
B
R
W
+
-
tekmar
actuating motors.
• Select the appropriate conversion circuit for the installation.
• Use 18 AWG or similar wire to connect the positive (+) and negative (-)
terminals to the modulating output on the control. The wire should be
run through a grounded metal conduit.
• Use 18 AWG or similar wire to connect the W, R, and B terminals to the
W, R, and B terminals on the gas valve actuator wiring terminals. The
wire should be run through a grounded metal conduit.
• Replace the front cover of the enclosure.
Modutrol IV
tekmar
V9055
B
R
W
+
-
B
R
W
+
-
tekmar
B
R
W
6
Mod 1 mA
+
V9055™
0 - 135 Ω
Actuating
Motor
7
–
Modutrol IV™ and V9055™ are trademarks of Honeywell, Inc.
1 of 2 © 2009 D 005 - 04/09
Technic al Da ta
0 – 135 Ω Converter 005
Literature — D 005
Packaged weight —
0.4 lb. (175 g), Enclosure E, glass reinforced modified PET
Dimensions — 4-1/2” H x 2-7/8” W x 1-1/2” D (73 x 114 x 38 mm)
Modutrol IV
B
R
W
Approvals — CSA C US, CSA/UL 61010-1, meets Class B:
ICES & FCC Part 15
Ambient conditions — 32 to 122°F (0 to 50°C)
tekmar
+
-
Caution The nonmetallic enclosure does not provide grounding between conduit connections. Use grounding type bushings and
jumper wires.
Attention Un boîtier nonmétallique n´assure pas la continuité électrique des conduits. Utiliser des manchons ou des fils de accord
spécialement conçus pour la mise á la terre.
V9055
B
R
W
+
-
tekmar
Limited Warranty and Product Return Procedure
Limited Warranty The liability of tekmar under this warranty is limited. The
Purchaser, by taking receipt of any tekmar product (“Product”), acknowledges the terms of the Limited Warranty in effect at the tim e of such Product
sale and acknowledges that it has read and understands same.
The tekmar Limited Warranty to the Purchaser on the Products sold hereunder
is a manufacturer’s pass-through warranty which the Purchaser is authorized
to pass through to its customers. Under the Limited Warranty, each tekmar
Product is warranted against defects in workmanship and materials if the Product is installed and used in compliance with tekmar’s instructions, ordinary
wear and tear excepted. The pass-through warranty period is for a period of
twenty-four (24) months from the production date if the Product is not installed
during that period, or twelve (12) months from the documented date of installation if installed within twenty-four (24) months from the production date.
The liability of tekmar under the Limited Warranty shall be limited to, at tekmar’s
sole discretion: the cost of parts and labor provided by tekmar to repair defects in
materials and/or workmanship of the defective product; or to the exchange of the
defective product for a warranty replacement product; or to the granting of credit
limited to the original cost of the defective product, and such repair, exchange or
credit shall be the sole remedy available from tekmar, and, without limiting the
foregoing in any way, tekmar is not responsible, in contract, tort or strict product liability, for any other losses, costs, expenses, inconveniences, or damages,
whether direct, indirect, special, secondary, incidental or consequential, arising
fro m owne rs hip or use of t he p ro du ct, or fro m defe ct s in workman ship o r ma teria ls,
including any liability for fundamental breach of contract.
The pass-through Limited Warrant y applies only to those defective Products
returned to tekmar during the warranty period. This Limited Warranty does not
cover the cost of the parts or labor to remove or transport the defective Product, or
to reinstall the repaired or replacement Product, all such c osts and expenses being
subject to Purchaser’s agreement and warranty with its customers.
Any representations or warranties about the Products made by Purchaser to its
customers which are dif ferent from or in excess of the tekmar Limited Warranty are
the Purchaser’s sole responsibility and obligation. Purchaser shall indemnify and
hold tekmar harmless from and against any and all claims, liabilities and damages
of any kind or nature which arise out of or are related to any such representations
or warranties by Purchaser to its customers.
The pass-through Limited Warrant y does not apply if the returned Product has
been damaged by negligence by persons other than tekmar, accident, fire, Act
of God, abuse or misuse; or has been damaged by modifications, alterations or
attachments made subsequent to purchase which have not been authorized by
tekmar; or if the Product was not installed in compliance with tekmar’s instructions
and/or the local codes and ordinances; or if due to defe ctive installation of the
Product; or if the Product was not used in compliance with tekmar’s instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, WHICH THE GOVERNING LAW ALLOWS PARTIES TO CONTRACTUALLY EXCLUDE, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, DURABILITY OR DESCRIPTION OF THE PRODUCT, ITS NON-INFRINGEMENT OF
ANY RELEVANT PATENTS OR TRADEMARKS, AND ITS COMPLIANCE WITH
OR NON-VIOLATION OF ANY APPLICABLE ENVIRONMENTAL, HEALTH OR
SAFETY LEGISL ATION; THE TERM OF ANY OTHER WARRANTY NOT HEREBY
CONTRACTUALLY EXCLUDED IS LIMITED SUCH THAT IT SHALL NOT EXTEND
BEYOND TWENTY-FOUR (24) MONTHS FROM THE PRODUCTION DATE, TO
THE EXTENT THAT SUCH LIMITATION IS ALLOWED BY THE GOVERNING
LAW.
Product Warranty Return Procedure All Products that are believed to have
defects in workmanship or materials must b e returned, together with a written
description of the defect, to the tekmar Representative assigned to the territory in
which such Product is located. If tekmar receives an inquir y from someone other
than a tekmar Representative, including an inquiry from Purchaser (if not a tekmar
Representative) or Purchaser’s customers, regarding a potential warranty claim,
tekmar’s sole obligation shall be to provide the address and other contact information regarding the appropriate Representative.
tekmar Control Systems Ltd., Canada
Control Systems
tekmar Control Systems, Inc., U.S.A.
Head Office: 5100 Silver Star Road
Vernon, B.C. Canada V1B 3K4
(250) 545 -7749 Fax. (250) 545-0650
Web Site: www.tekmarcontrols.com
Product design, software and literature are Copyright © 2009 by:
2 of 2
tekmar Control Systems Ltd. and tekmar Control Systems, Inc.
All specifications are subject to change without notice.
Printed in Canada. D 005 - 04/09.