Teka CNL 1001, CNL 2002 Instruction Manual

Download

Page 1

Instrucciones para el montaje

y recomendaciones para el mantenimiento

Campanas CNL 1001 / CNL 2002

Einbauanleitung und Pflegehinweise

Dunstabzugshauben CNL 1001 / CNL 2002

Instruction Manual

Cooker Hood CNL 1001 / CNL 2002

Instructions pour le montage

et Recommandations pour l´entretien

Hottes CNL 1001 / CNL 2002

Manual de Instruções

Exaustores CNL 1001 / CNL 2002

(Turco)

Turco CNL 1001 / CNL 2002

(Griego)

Griego CNL 1001 / CNL 2002

Page 2

Page 3

Dear customer, We congratulate you on your choice. We are

sure that this modern, functional and practical article, constructed from highest quality materials, will fully meet your requirements.

Please read all the sections of this INSTRUCTION MANUAL before using the extractor for the first time to be able to obtain its full performance and to avoid any breakdowns that could arise from its misuse, also allowing small problems to be overcome.

Keep this manual. It will always provide useful information on the extractor and will help other people to use it.

Safety Instructions

* Before using the extractor for the first time, you must observe the installation and connection instructions.

* Never pull the cable to unplug the extractor. Always pull the plug.

* Do not switch on the extractor if the electricity cable is worn or has cuts or if there are signs of deterioration around the control panel.

* If the extractor stops working or functions abnormally, unplug it from the mains and advise the technical service.

* Do not leave gas burning without a pan above it under the hood.

* Do not allow grease to accumulate in any part of the extractor, especially in the filter as this COULD PRODUCE A FIRE RISK

* Do not flambé food under the hood. * Before installing the extractor consult local

rules and regulations in force with respect to current standards on air and fumes.

* Before connecting the extractor to the mains, check that both the voltage and the frequency conform to that shown on the characteristics label of the extractor located inside it.

* Switching on and off must be by means of an omnipolar switch with minimum separation between contacts of 3 mm incorporated into the fixed installation.

* The electrical connection must be made by means of a flexible cable. It is not allowed to connect it by means of a rigid conduit.

* The expelled air must not reach a duct that is used to expel food processor fumes using energy other than electricity.

* The room must be provided with appropriate ventilation if the extractor is going to be used at the same time as other food processing equipment not using electrical power.

* We recommend the use of gloves and caution when cleaning the inside of the extractor.

* Your extractor is designed for domestic use and only for expelling and purifying gases arising from food preparation. Its use for any other purpose must be at your own responsibility and may be dangerous.

* You should contact the nearest Qualified Technical Assistance Service for any repairs always using original spare parts. Repairs and modifications carried out by others could damage the apparatus or cause it to malfunction, and risking your safety. The manufacturer cannot be held liable for inappropriate use of the apparatus.

Page 4

Index

Description of apparatus Page 3 Instructions for use 3 Cleaning and maintenance 4 Technical Information 4 Installation 5 If something does not work 5

Description of the apparatus

A Motor controls that allow three

positions to be selected

B Light switch independent of the motors C Lighting by means of lamps D Filters located over cooking area, easily

withdrawn for cleaning

E Extractable group that allows a greater

gas capture area

F Possibility of incorporating activated

charcoal filter

G Anti return tabs to be located in the

outlet mouth, locating their ends in the holes provided.

Instructions for use

By pressing the button shown in the figure, you will be able to control the functions of the extractor

Speed Light I Low switch on/off

II High + Intensive

Two achieve better extraction, we recommend switching on the extractor a few minutes before starting to cook (3 - 5 minutes) so that the air flow is continuous and stable when extracting the fumes.

Likewise,keep the extractor switched on for a few minutes when cooking is complete to allow all fumes and odours to be expelled.

F I I F

Page 5

Cleaning and maintenance

Before carrying out any cleaning or maintenance activities, ensure that the extractor is disconnected from the mains.

To carry out cleaning and maintenance, follow the safety instructions indicated on Page 3.

Filter cleaning

To withdraw the filters from their locations release the anchoring points. Clean the filter, either by putting it in the dishwasher (see notes) or leaving it standing in hot water to simplify the removal of grease or, if wished, by means of special sprays (protecting the non metallic parts). Once clean, leave it to dry.

Notes: cleaning in the dishwasher with aggressive detergents may blacken the surface of metallic parts, without this affecting its gas retaining properties.

N.B. The filter must be cleaned at least once a month depending on how often the extractor is used. It must be remembered that grease is deposited in the extractor when cooking, whether it is switched on or not.

Cleaning of the extractor body

The use of warm (40ºC approx.) soapy water is recommended. A cloth moistened in this water is used for cleaning the extractor, paying special attention to the grids. Afterwards, dry using a lint-free cloth.

Note: Never use metallic scouring pads or abrasive products that could damage the surface.

Do not use scrapers with metallic surfaces such as knives, scissors etc.

Activated charcoal filter

To install the charcoal filter, the motor anchorage is made to coincide with the anchor points of the activated charcoal filter and turn it clockwise. The carbon filter lasts from three to six months depending on the particular conditions of use. The activated carbon filter can neither be washed nor regenerated. Once it is exhausted, it must be changed. To replace exhausted filters with new ones, withdraw the old one in the reverse order to that of installation.

Chaging Bulbs

Remove the filter support to acces the bulbs. Take care to disconnect the mains beforehand and that the bulbs to be replaced are not hot. The maximum bulbs power is 40W.

Technical information

Dimensions Width = 600 mm

Depth = 300 mm Height = 185 mm

Electrical characteristics REFER TO CHARACTERISTICS LABEL

300

475

600

559

184

142

Mod. Typ.

POTENCIA NOM. LAMPARAS NENNLEISTUNG GLÜHLAMPEN LAMPS RATE PUISSANCE LAMPES POTENCIA NOM. DAS LAMPADAS

2x40 W

XXX – ZZ Z-000000

N.º de fábric. Fabrik.-Nr. Serial No.

Made in European Community - C.I.F.: A-39004932

AA-000000

ELECT.

000…000 V. ~

00 Hz

000 W.

Page 6

Installation

To fix the extractor to the kitchen unit the pattern on page 6 is used. The lower part of the extractor must be located at a minimum height of 60 cm above the hob for electric cookers and 65 cm for gas cookers. If the instructions of a gas cooker indicate a greater distance these must be observed. The extractor must be connected to a wall socket with an effective earth. When the extractor is working at the same time as other non-electrical cooking equipment, the outlet air pressure must not exceed 4 Pa (4 x 10

-5

bar). To achieve optimum performance the length of the outlet hose should not exceed 4 meters, or include more than two 90º angles (elbows) Although venting to the outside is recommended, activated carbon filters may be used, which allow the gas to be returned to the kitchen through the outlet pipe. If you wish to exchange the front for one matching the kitchen units, follow the following instructions:

- Withdraw the movable group.

- Remove the screws (T) that support

the front

- Install the new front fixing it with the same

screws that held the old one.

If something does not work

Before seeking technical assistance carr y out the following checks first

Defect Possible cause Solution The extractor does The cable is not connected Connect the mains cable not work No current is reaching the plug Revise/repair the

electricity circuit

The extractor does not Filter saturated with grease Clean or substitute filter blow enough or vibrates

Outlet obstructed Eliminate obstructions

Inadequate air conduit Contact the installer and follow

instructions of this manual

The lamps do not light Lamp broken Exchange the bulb

Lamp loose Tighten bulb

320

340

Page 7

Special U.K. Requirements

Height above gas hob: 75 mm minimum NEVER PLACE THE COOKER HOOD OVER AN EYE-LEVEL GRILL This appliance must be connectec by a competent person, using fixed wiring via a DOUBLE POLE SWITCHED FUSED SPUR OUTLET

Electical connection

We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. Should the colour of the wires in the manis lead for the appliance not correspond with the coloured markings identifying the

terminal in your spur box proceed as follows:

• The wire which is coloured blur must be connected to the marked N (Neutral) or coloured Black.

• The wire which is coloured brown must be connected to the marked L (Live) or couloured Red.

• Where avialable (see installation), the wire which is coloured yellow/green must be connected to the market or coloured Yellow/Green.

If the cooker hood is installed for use above a gas appliance then the provision vor ventilation must be in accordance with the Gas Safety (Installation & Use) Regulations 1984 and the relevant Building Regulations. Detailed recommendations are contained in the following British Standard Codes of Practice BS6172, BS5440 and BS6891 Current Edition.

Page 8

4 x Ø8

Ø132

559

151

458

598

214 300

Outlet for two motors Outlet for single motor Front of extractor

B C

Drilling pattern for installation in the kitchen unit