USER MANUAL
WARRANTY INFORMATION INSIDE. PLEASE READ
www.teac.com.au
IMPORTANT !
LCDV2655HD
LCD TV
WARRANTY REGISTRATION
Please read this warranty card.
Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty Service.
Warranty Terms & Conditions
1. TEAC warrants to the original retail purchaser only, that this product is free from defects in material and
workmanship under normal domestic use and authorises free service during the warranty period at any TEAC
Authorised Service Centre only. TEAC warranty only applies to products purchased, used and serviced in Australia.
2. Subject to the terms herein, this warranty effectively covers the equipment as specified in the Warranty Periods
Table below from the date of purchase.
TEAC PRODUCT
WARRANTY PERIOD
Plasma TV 106 cm and above 1 Year (In-Home Service/ Pick up Available)*
LCD Televisions 80 cm and above 1 Year (In-Home Service/Pick up Available)*
Televisions – 59cm and above 1 Year (In-Home Service/ Pick up Available)*
All Televisions under 59 cm 1 Year (No In-Home Service)
Digital Set Top Boxes & Module 1 Year (No In-Home Service)
VCR 1 Year (No In-Home Service)
DVD & Module 1 Year (No In-Home Service)
DVD Recorder & PVR Module 1 Year (No In-Home Service)
Audio Systems 1 Year (No In-Home Service)
3. In Home Service/Pick up* will only be provided as part of this warranty if all the following conditions are met;
a) The product as indicated in the Warranty Period Table.
b) The product is within the warranty period.
c) The product is located within the normal service area of the local TEAC Authorised Service Centre.
In any other situation or circumstance, where an In Home Service/Pick up* call is made, a service fee will be
charged by the Service Provider including a travel fee if outside normal service area.
If TEAC determines that the product is not repairable on site, TEAC can complete the repair by taking the product
to a TEAC Authorised Service Centre.
Where In-Home service/Pick up* is not available, the purchaser is required to send the product to the nearest TEAC
Authorised Service Centre for repair. In this event, a copy of this warranty card and a copy of your receipt of
purchase must be enclosed to be a valid warranty. Such equipment or part must be sent freight prepaid to your
nearest TEAC Authorised Service Centre. After the repair, the product will be available for collection by or return to
the purchaser at purchaser’s cost. The warranty does not cover freight or insurance. In all cases of transit damage or
lost, a claim must be filed against the carrier by the purchaser, even if shipment is arranged by TEAC. TEAC inhome service may also be available at a fee upon request.
4. Accessories, Remote, including power adaptors, AV box, TV tuners, etc, are warranted to be defect free for 1 year.
5. Replacement of spare parts under normal usage; except cabinet, front panel, knob, removable accessories, battery,
consumable, AC cord, connecting cord and other accessories, are warranted as specified in Warranty Periods Table,
and will be repaired or replaced at the sole judgement of TEAC.
6. The warranties hereby conferred do not extend to, and exclude, any cost associated with the installation, de-
installation or re-installation of a product (be it in-home or otherwise), including costs related to the mounting,
demounting or remounting of any screen, (and any other ancillary activities), delivery, handling, freighting,
transportation or insurance of the product or any part thereof or replacement of and do not extend to, and exclude,
any damage or loss occurring by reason of, during, associated with, or related to such installation, de-installation,
re-installation or transit.
7. Normal customer maintenance as described in the owner’s manual is not covered by this warranty (such as cleaning
VCR heads etc.)
8. Service will be provided only during normal business hours and under safety conditions and circumstances.
9. This warranty does not apply to equipment showing abuse, damage or that it may have been tampered with, altered
or repaired outside any TEAC Authorised Service Centre. If so, the warranty will be void.
*Your nearest Authorised TEAC Service Centre is listed in your Owner’s Manual, please refer to TEAC
website for up to date list.
10. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with
the sale of any equipment other than as stated in this warranty and outlined above.
11. In no event will TEAC be responsible or liable for indirect or consequential damages from interrupted operations or
other causes.
12. Warranty is not transferable to any subsequent purchaser if the product is sold during the warranty period.
13. LCD dead pixel policy, please contact TEAC Customer Care Centre on 1800 656 700 for assistance.
* Extended promotional warranty may apply to certain products (for more info please contact: service@teac.com.au)
In home service administration fee is applied after 1
st
year of warranty.
WARRANTY PROCEDURES
Please keep this information for your own records.
Please refer to the owner’s manual to ensure that you have followed the correct installation and operating procedures.
1. Read owner’s manual carefully
2. If you require Warranty Service, please contact the TEAC Authorised Service Centre
3. Please have your purchase receipt as your proof of purchase and the following details completed for a valid
Warranty.
Owner’s Name
Owner’s Address
Postcode
Model Name/No. Serial No.
Dealer’s Name
Dealer’s Address
Postcode
4. Please ensure that your product is packed appropriately upon return to the service centre.
If you have any other queries regarding service or warranty please contact the TEAC Customer Care Centre below:
service@teac.com.au
www.teac.com.au
1800 656 700
Table Of Contents
Important Safety Instructions......................................................................................................... 1
View of Unit ......................................................................................................................................3
Special Feature of DVD Module .....................................................................................................6
Disc Information ..............................................................................................................................7
Remote Control................................................................................................................................8
System Connections ..................................................................................................................... 12
Connecting to the Power Supply .....................................................................................................12
Connecting to an External AV Signal Source (AV2/S-Video)...........................................................12
Connecting to an External AV Signal Source (AV1) ........................................................................13
Connecting to an External AV Signal Source(YPbPr) ..................................................................... 14
Connecting to an External AV Signal Source(HDMI).......................................................................15
Connecting to an External AV Signal Source(AV Output)................................................................15
Connecting to Coaxial Digital Output............................................................................................... 16
Connecting to a USB Device for Upgrading ....................................................................................16
Connecting to a PC.......................................................................................................................... 17
Connecting to a TV Antenna............................................................................................................ 17
Input Source Selecting.................................................................................................................. 18
TV Function .................................................................................................................................... 19
Installation Guide ............................................................................................................................. 19
Channel Setting ...............................................................................................................................20
Picture Setting .................................................................................................................................22
Sound Setting ..................................................................................................................................25
Time Setting..................................................................................................................................... 26
Option Setting .................................................................................................................................. 27
EPG Function ................................................................................................................................. 29
NICAM Function.............................................................................................................................30
DVD Playback Operation...............................................................................................................31
USB and SD/MS/MMC Card Function .......................................................................................... 36
DVD System Setup ........................................................................................................................37
Troubleshooting ............................................................................................................................43
Specifications ................................................................................................................................44
- 1 -
Important Safety Instructions
Caution: use of any controls, adjustments, or procedures other than those specified herein may
result in hazardous radiation exposure.
Caution
1. The product contains a low-power device. In order to ensure the safety of the laser device, do
not remove any cover and attempt to repair the unit. If any service is needed, please contact
the distributor or its authorised service centre.
2. To reduce the risk of electric shock, do not remove the cover (back). No user-serviceable parts
inside. Refer servicing to qualified service personnel. Unplug the product from the wall outlet
before servicing or when it is unused for a long period of time.
3. The manufacturer will not be held responsible for the damage caused by any substitutions and
modification of the product without authorisation from the manufacturer’s or authorised service
agent.
WARNING
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
NON ANALOG OUTPUT MANUFACTURER LICENSE AGREEMENT
This product incorporates copy protection technology that is protected by U.S. and foreign patents,
including patent numbers 5,315,448 and 6,836,549, and other intellectual property rights. The use
of Macrovision's copy protection technology in the product must be authorized by Macrovision.
Reserve engineering or disassembly is prohibited.
The images in this manual are for reference only and may differ from your model.
This symbol indicates that dangerous voltage instituting a risk of electric shock is
present within this unit.
This symbol indicates that there are important operation and maintenance
instructions in the literature accompanying the appliance.
Caution: Laser radiation when open. Do not stare into beam.
- 2 -
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Maintain well
ventilated conditions around
the product. Do not put product on a bed, sofa or anything that blocks ventilation. Install
according to the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Read, heed and follow all instructions to ensure correct and safe installation and
interconnection of the apparatus;
10. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
11. The mains socket-outlet shall be installed near the apparatus and the mains plug shall remain
readily operable.
12. Protect the power cord from being walked on or pinched particularly at plugs, power sockets,
and the point where they exit from the apparatus.
13. Only use attachments/accessories specified by the manufacturer.
14. Use only with the stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus.
15. Unplug the apparatus during lightning storms or when unused for long periods of time.
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
17. The apparatus shall be connected to a mains socket outlet with a protective earthing
connection.
Note: Do not touch the color TFT LCD screen directly by hand.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to
beam.
3. CAUTION: Do not open the back cover. There are
no user serviceable parts inside the unit. Leave all
servicing to qualified service personnel.
- -
- 3 -
View of Unit
Left Side Panel
1. EJECT button
Press to eject the disc from the unit.
2. ■ STOP button
Press to stop disc playback in DVD mode.
3.
PLAY/PAUSE button
Press to start disc playback and press it
again to pause playback in DVD mode .
4. Disc Tray Slot
Insert disc into this slot.
5. SD/MS/MMC Card Port
Insert SD/MS/MMC card into this slot.
6. USB Port
Connect the USB device.
7. INPUT button
Press to select enter the source selecting
menu, press the ▲▼ direction buttons to
select desired mode and press the ENTER
button to enter the selected mode.
In setup menu, use the ENTER button for
the same function.
8. MENU button
Press to enter the system setup menu.
9. CH+/- buttons
In TV or DTV mode, press to select
channels;
On system setup menu, the same function
as ▲/▼ direction buttons.
10. VOL+/- buttons
Press to decrease or increase the volume;
On system setup menu, the same function
as ◄/► direction buttons.
11. POWER button
Press to enter or exit standby mode.
- -
4
View of Unit
Front Panel
12. Color TFT Screen
13. Power Indicator
Lights blue while system is active and red while system is in standby mode.
14. Remote Sensor
15. Speaker
NOTE:
The “
PLAY/PAUSE”, “■ STOP”, “ EJECT” buttons are available when the DVD module is
connected.
- -
5
View of Unit
Rear Panel and Right Side Panel
1. AV2/S-VIDEO Input Jacks
Connect Composite/S-Video signal source
in Composite 2 or S-Video mode. AV2 and
S-Video share L/R audio jacks.
2. Power Supply Cord
3. upgrade port
Connect the USB device only for
upgrading the TV software.
4. HDMI 1 and HDMI 2 Input Jacks
Connect the HDMI signal source.
5. VGA Input Jack
Connect the VGA signal source in VGA
mode.
6. Y/Pb/Pr (Component) and L/R audio
Input Jacks
Connect the Y/Pb/Pr (Component) signal
source in Component mode.
7. COAXIAL Output Jack
Output the coaxial digital audio signal.
8. AV1 and L/R Audio Input Jacks
Connect AV1 signal source in Composite 1
mode.
9. AV Output Jacks
Connect to output the audio/video signals.
10. TV antenna Input Jack
Connect the external TV antenna signal
source.
- -
6
Special Feature of DVD Module
Your TV comes equipped with a removable DVD module. Please follow the procedures below to
remove or install the DVD module.
Note:
Before removing or installing the DVD module, ensure that the television is unplugged and turned
off.
DVD module removal:
Refer to the illustration below and follow the procedures below to remove the DVD module from the
unit:
1. Loosen the screw on the DVD module.
2. Carefully slide the DVD module along the rails and unplug the connecting cord from the LCD
TV.
3. Slide the DVD module along the rails to fully remove the DVD module.
DVD module installation:
1. Plug the connecting cord into the DVD module.
2. Carefully slide the module into the desired position and lock the function module with one
screw.
- -
7
Disc Information
Discs Supported
DISC LOGO CONTENTS SIZE MAXIMUM TIME
133min(SS-SL)
242min(SS-DL)
266min(DS-SL)
DVD
Audio+Video
(active picture)
12cm
484min(DS-DL)
CD
Audio 12cm 74min
JPEG
Still high resolution 12cm
DIVX
12cm
z The operating method of some DVD discs is specified by the software maker. Please refer to
the instruction manual of the disc.
z The unit will play most recordable (CD-R) or erasable (CD-RW) CDs, but playback of CD-R or
CD-RW discs created on a computer requires proper formatting and finalization of the disc for
audio playback. Some computers and/or software programs may not be capable of creating
compatible discs.
About Disc Terms
Title
Generally, pictures or music compressed on a DVD are divided into several sections, “title”.
Chapter
The smaller section unit of pictures or music in a DVD under the title, usually one title is comprised
of one or more chapters and each of them is numbered for easy searching. But some discs may not
have a recording by chapter facility.
Track
A segment of picture or music on a CD. Each track is numbered for searching.
- -
8
Remote Control
Remote Control Drawing
1. POWER button
Press to enter or exit standby mode.
2. DTV button
Press to enter DTV mode.
3. ATV button
Press to select ATV mode.
4. SOUND button
Press to select the screen picture mode:
choose from Standard, User, Sports,
Movie or Music.
5. TV.RADIO button
Press to select DTV program playback or
Radio program playback in DTV mode.
6. 0~9 Number buttons
Press to select numbers such as TV
channel.
7.
button
In TV or DTV mode, press to return to the
channel previously viewed.
8. STEREO button
Press to select sound track in TV mode.
9. VOL+/- button
Press to increase or decrease the volume.
10. MUTE button
Press to turn on or off the speaker output.
11. INPUT button
Press to select enter the source selecting
menu, press the ▲▼ direction buttons or
press the INPUT button repeatedly to
select desired mode and press the ENTER
button to enter the selected mode.
12. Direction buttons (▲▼◄►)
In the setup menu, press the ▲▼ button to
select a desired item and press the ◄►
button to adjust or set.
13. ENTER button
Press to confirm your operation in setup
menu.
14. DISPLAY button
Press to display the reference information
of the current mode.
15. PAUSE button
In DVD mode, press to pause playback
and again to resume.
- -
9
Remote Control
16. ► PLAY button
Press to play a disc in DVD mode.
17. / button
Press to search backward or forward in
DVD mode.
In Channel Edit menu, press the red button
to delete a channel and use the green
button to rename a channel (see P21 for
details).
In teletext mode, they are the teletext
colour buttons.
18. SETUP button
In DVD mode press to enter the DVD
setup menu.
In TV mode, press to display or close the
teletext.
19. MENU button (under DVD mode)
Press to enter disc menu in DVD mode.
In teletext mode, press to disable teletext
display for page updates and press again
to resume.
20. SUBTITLE button
In DTV/DVD mode, press to select
alternate subtitle languages during
view/playback of a DTV program or
multiple language DVD disc.
In teletext mode, press to display index
page.
Note: Subtite and teletext is only available
if the service is provided by broadcaster.
21. AUDIO button
In DVD mode, press to select the audio
language or audio track.
In teletext mode, press once to display the
concealed information, such as solution of
riddles or puzzles; press again to remove
the riddles answers from the display.
22. FAV.LIST button
Press to display the favorite channel list.
In Channel Edit menu, press this button to
set a favorite channel (see P21 for details).
23. CH.LIST button
Press to display the channel list.
24. ASPECT button
Press to shift the aspect ratio of the screen
among 16:9, Zoom1, Zoom2, Auto and
4:3.
25. EPG button
Press to display the CHANNEL GUIDE
menu in DTV mode.
26. +10 button
In DVD mode, press to select numbers
greater than 9.
27. PICTURE button
Press repeatedly to select the picture
mode: Standard, Dynamic, User or Mild.
28. CH ▲/▼ button
In TV or DTV mode, press to select analog
channel or digital channel.
29. SLEEP button
This feature allows you to set the sleep
time. Press the button repeatedly to select
the desired time to sleep or select Off to
close the function.
30. MENU button
Press to enter or exit the setup menu.
31. EXIT button
Press to exit all the OSD on the screen.
32. ■ STOP button
Press to stop disc playback in DVD mode.
33.
EJECT button
Press to eject the disc from the unit.
- -
10
Remote Control
Remote Control Drawing
34. / Next Skip button
Press to skip to the previous or next
chapter/track in DVD mode.
In Channel Edit menu, press the yellow
button to move a channel and use the blue
button to skip a channel (see P22 for
details).
In teletext mode, they are the teletext
colour buttons.
35. REPEAT button
Press to repeat a chapter, track, title or all
program content in DVD mode.
In teletext mode, press to hold the current
page and press again to resume.
36. TITLE button
During disc normal playback, press to go
to display the title menu.
In teletext mode, press the button first time
to double the size of teletext letters in the
upper half of the screen, second to double
the size of teletext letters in the lower half
of the screen and third to resume normal
status.
37. CARD button
Press to shift among disc playback, USB
playback and SD/MS/MMC playback.
In teletext mode, press to select four
groups of 3-digit numbers that are
displayed in different colours at the bottom
of the screen. Press the colour buttons on
the remote control to select, then use the
number buttons to input the corresponding
number to display the page.
Repeat the above procedures for each
page to be stored, using a different colour
button each time.
38. GOTO button
Press to select the desired disc starting
time, title or chapter in DVD mode.
In TV mode, press to display the real clock
and press the EXIT button to exit.
- -
11
Remote Control
Preparation of Remote Control
Softly push the back cover to open the battery
compartment.
Insert two batteries (1.5V, size AAA), please
make sure the polarity matches the marks
inside the compartment.
Softly press the back cover to close it.
z Under normal use the battery will last for
six months.
z Take out battery when the remote is not in
use for a long time.
Using of Remote control
Point the remote control unit from no more than
about 7 meters from the remote control sensor
and within about 60 degrees of the front of the
unit.
• The operating distance may vary
depending on the brightness in the room.
Notes:
• Do not point bright lights directly at the
remote control sensor.
• Do not place objects between the remote
control unit and the remote control sensor.
• Do not use this remote control unit while
simultaneously operating the remote
control unit of any other equipment.
- -
12
System Connections
• Open the back cover on the right side of the unit’s rear panel.
• Do not connect the power cord until all other connections have been made.
• Ensure that you observe the color code when connecting audio and video cables.
Connecting to the Power Supply
Connect the power supply cord to the wall AC outlet, see the figure below.
Connecting to an External AV Signal Source (AV2/S-Video)
Use the AV cables to connect the external AV signal source to the AV input jacks on the rear panel
of the unit. Use a S-VIDEO cable (not supplied) to connect the external AV signal source to the
S-VIDEO input jack on the rear panel of the unit.
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select Composite 2 or S-Video mode, and then press the ENTER button to
confirm.
¾ The L/R audio input jacks can be used in both Composite 2 and S-VIDEO modes.
- -
13
System Connections
Connecting to an External AV Signal Source (AV1)
Use the AV cables to connect the external AV signal source to the AV input jacks on the rear panel
of the unit.
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select Composite 1 mode, and then press the ENTER button to confirm.
- -
14
System Connections
Connecting to an External AV Signal Source (YPbPr)
Use AV cables to connect an external AV signal source to the Y/Pb /Pr (Component) input jacks on
the rear panel of the unit.
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select Component mode, and then press the ENTER button to confirm.
- -
15
System Connections
Connecting to an External AV Signal Source (HDMI)
Follow the figure below to connect an HDMI signal source to one of the HDMI jacks on the rear
panel of the unit.
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select HDMI 1 or HDMI 2 mode, and then press the ENTER button to confirm.
¾ HDMI provides both audio and video signals and typically provides superior image
quality to component, S-Video or composite.
Connecting to an External Signal Source (AV Output)
Use the AV cables to connect the external AV input device to the AV output jacks on the rear panel
of the unit.
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select the corresponding mode, and then press the ENTER button to confirm.
- -
16
System Connections
Connecting a Coaxial Digital Output
This unit is designed with a coaxial digital audio jack, can be connected to the digital amplifier, see
the figure below:
Note:
¾ This feature is available only for amplifiers equipped with coaxial digital audio input
connectors.
¾ For TVs with a built-in DVD player (optional) and an amplifier with Dolby Digital decoding
function, set the digital audio signal output format in DVD setup menu to “RAW”.
Connecting a USB Device for Upgrading
This unit is designed with a USB upgrade port, can be connected to the USB device for upgrading
the software, see the figure below:
¾ Make sure that upgrading files are stored in the USB device before connection.
- -
17
System Connections
Connecting to a PC
Follow the steps and figure below to connect PC to the unit.
1. Connect one end of the VGA cable to the VGA input jack on the jack panel of the unit and the
other end to the PC VGA output.
2. Connect one end of the audio cables to the PC audio input jack on the jack panel of the
television and the other end to the PC audio output jack.
3. Set the PC video resolution to match that of the television (typically 1024 x 768@60Hz).
After connection, turn on the power of the unit and the external AV signal source. Press INPUT then
direction buttons to select VGA mode, and then press the ENTER button to confirm.
Connecting to a TV Antenna
Connect TV signal input source from the aerial to the TV jack on the rear panel of the unit.
After connection, turn on the power of the unit. Then press the INPUT button and the direction
buttons to select TV or DTV mode, press the ENTER button to confirm and conduct program
selection.
- -
18
Input Source Selecting
The unit incorporates multiple video modes which can be selected via the Input button on the
television or remote.
Press the INPUT button to enter Input menu. The screen will display as shown below:
Use the ST direction buttons and ENTER button
On the input menu, press the ST direction button to select the desired video mode. After
several seconds, you can enter the selected mode.
Or after you selected the desired mode press the ENTER button to enter the selected mode
immediately.
Use the INPUT button and ENTER button
On the input menu, press the INPUT button repeatedly to select the desired video mode. After
several seconds, you can enter the selected mode.
Or after you selected the desired mode press the ENTER button to enter the selected mode
immediately.
- -
19
TV Function
Preparations
1. After connection, press the POWER button to turn on the unit.
2. Press the INPUT button to select TV mode and you can then conduct the following
operations:
Note: In other mode, you can refer to the following instructions in TV mode to go on with
some settings.
Installation Guide
When you turn on the TV for the first time or after you reset all the settings to their original status,
the Installation Guide page appears automatically. Please follow the instructions to finish the
installation guide setup. It helps to quick set the language and get the channels.
The Installation Guide menu shown on the right will
be displayed on the screen after you press the
INPUT button to select TV mode.
The Language option is highlighted and the default
is English. You can select the desired OSD
language you want by pressing the ◄► button.
Press the ▼ button to highlight Auto Tuning option
and press the ENTER or ► button to prompt a
information box, as shown on the right:
Press the ◄► button to select a desired country.
Press the ▼ button to highlight Start and press the ENTER
button to start auto searching the available channels. The
menu on the right will be displayed on the screen to show the
progress of the search for TV, DTV and Radio programs.
During searching, press the MENU button to skip some
range of available channels. Press the EXIT button to exit.
- -
20
TV Function
If you use the unit for the first time or if your setup has changed, you can setup the unit from
Channel Setup menu. Please follow the instructions below:
Channel Setting
Press the MENU button once to enter CHANNEL
setup menu as shown on the right.
Press the ENTER or ► button to enter the menu.
In the CHANNEL setup menu, press the ▲▼
button to select the desired item. Press the MENU
button to return to the previous menu. Press the
EXIT button to exit.
Auto Tuning
Press the ▲▼ button to select Auto Tuning and
press the ENTER or ► button, the screen will
display as shown on the right:
Press the ◄► button to select desired country and
press the ▼ button to highlight “Start”. To cancel
auto tuning, press the ENTER button after highlight
“Cancel” by pressing the ◄► button.
To start auto tuning, press the ENTER button after highlighting
“Start”. The screen will display as shown:
When auto tuning is over, all searched channels will be stored
automatically and it will return to the first searched channel.
During searching, press the MENU button to skip some range
of available channels. Press the EXIT button to exit.
Notes:
Channel Tuning scans the analog channels, digital
channels and Radio programs.
Please allow a few minutes for this feature to scan the
entire range of available channels to ensure accurate
programming of available channels.
- -
21
TV Function
DTV Manual Tuning
Press the ▲▼ button to select DTV Manual Tuning and
press the ENTER or ►button, the screen will display as
shown on the right:
Press the ◄► button to select desired channel number and
press the ENTER button to start tuning.
ATV Manual Tuning
Press the ▲▼ button to select ATV Manual Tuning and press
the ENTER or ► button, the screen will display as shown on
the right:
Within this menu, press the ▲▼ button to select desired item
and press the ◄► button to set or activate. Press the red
button to save the settings.
Channel Edit
Press the ▲▼ button to select Channel Edit and press the
ENTER or ► button, the screen will display as shown:
Set a favorite channel:
Within the menu, press the ▲▼ button to select a channel
and press the FAV.LIST button to set it as your favorite
channel, press the FAV.LIST button again to cancel.
Delete a channel:
Press the ▲▼ button to select a channel you want to
delete and press the red button to set a symbol “ ” on
the channel. Press the red button again to delete the
selected channel, press the MENU button to return.
- -
22
TV Function
Rename a channel: (this function is only available for ATV channels)
Press the ▲▼ button to select a channel you want to rename and press the green button to set
a symbol “ ” on the channel. Press the ◄► button to highlight the character position of
channel name and press the ▲▼ button to select desired character, press the MENU button to
confirm and return.
Move a channel: (this function is only available for ATV channels)
Press the ▲▼ button to select a channel you want to move and press the yellow button to set a
symbol “ ” on the channel. Press the ▲▼ button to select the desired position and press
the MENU button to move the selected channel to the position you select.
Skip a channel:
Press the ▲▼ button to select a channel you want to skip and press the blue button to set the
channel skipped. A symbol “ ” is appear on the skipped channel. Press the blue button
again to cancel, press the MENU button to return.
Note:
A skipped channel is skipped when using the CH▲/▼ button to browse the channels but can
be watched by selecting in the channel list or using the number buttons.
Picture Setting
Press the MENU button once to enter CHANNEL
setup menu and press the ▲▼ button to select
PICTURE, the screen will display as shown.
Press the ENTER or ► button to enter the menu.
In the PICTURE setup menu, press the ▲▼ button
to select the desired item. Press the MENU button
to return to the previous menu. Press the EXIT
button to exit.
Picture Mode
Press the ▲▼ button to select Picture Mode and press the ◄► button to select Standard, Mild,
User or Dynamic.
Contrast
Press the ▲▼ button to select Contrast and press the
◄► or ENTER button to enter the contrast adjusting bar.
Press the ◄► button to adjust the difference between the
brightest and darkest regions of the picture.
- -
23
TV Function
Brightness
Press the ▲▼ button to select Brightness and press the
◄► or ENTER button to enter the brightness adjusting
bar. Press the ◄► button to darken or brighten the picture.
Color
Press the ▲▼ button to select Color and press the ◄►
or ENTER button to enter the color adjusting bar. Press
the ◄► button to adjust the level.
Sharpness
Press the ▲▼ button to select Sharpness and press the
◄► or ENTER button to enter the sharpness adjusting
bar. Press the ◄► button to adjust the level.
Tint
Press the ▲▼ button to select Tint and press the ◄► or
ENTER button to enter the adjusting bar. Press the ◄►
button to adjust the level.
Notes:
This item is only available under NTSC signal mode.
The items Contrast, Brightness, Color, Sharpness and Tint are only available when Picture
Mode is set to User.
Within the adjusting bar, you can select Contrast, Brightness, Color, Sharpness and Tint by
pressing the ▲▼ button.
Color Temperature
Press the ▲▼ button to select Color Temperature and press the ◄► button to select User, Warm,
Medium or Cool.
Red
Press the ▲▼ button to select Red and press the ◄► or
ENTER button to enter the adjusting bar. Press the ◄►
button to select adjust the level.
Green
Press the ▲▼ button to select Green and press the ◄►
or ENTER button to enter the adjusting bar. Press the
◄► button to select adjust the level.
- -
24
TV Function
Blue
Press the ▲▼ button to select Blue and press the ◄►
or ENTER button to enter the adjusting bar. Press the
◄► button to select adjust the level.
Note:
The items Red, Green and Blue are only available when Color Temperature is set to User.
Within the adjusting bar, you can select Red, Green and Blue by pressing the ▲▼ button.
Aspect Ratio
Press the ▲▼ button to select Aspect Ratio and press the ◄► button to select Auto, 4:3, 16:9,
Zoom1 or Zoom2.
Noise Reduction
Press the ▲▼ button to select Noise Reduction and press the ◄► button to select Off, Auto,
High, Standard or Low.
Screen
This item is only available in VGA mode.
Press the ▲▼ button to select Screen and press
the ► or ENTER button to enter its sub menu, as
shown on the right:
Within this menu, press the ▲▼ button to select
desired item and press the MENU button to return.
Press the EXIT button to exit.
Auto Adjust
Press the ▲▼ button to select Auto Adjust and press the ► or ENTER button to start auto
adjusting the screen.
Horizontal Pos.
Press the ▲▼ button to select Horizontal Pos. and press the ◄► button to adjust the level.
Vertical Pos.
Press the ▲▼ button to select Vertical Pos. and press the ◄► button to adjust the level.
Size
Press the ▲▼ button to select Size and press the ◄► button to adjust the level.
Phase
Press the ▲▼ button to select Phase and press the ◄► button to adjust the level.
- -
25
TV Function
Sound Setting
Press the MENU button once to enter CHANNEL
setup menu and press the ▲▼ button to select
SOUND, the screen will display as shown.
Press the ENTER or ► button to enter the menu.
In the SOUND setup menu, press the ▲▼ button
to select the desired item. Press the MENU button
to return to the previous menu. Press the EXIT
button to exit.
Sound Mode
Press the ▲▼ button to select Sound Mode and press the ◄► button to select Standard, Music,
Movie, Sports or User.
Note:
The items Treble and Bass are only available when Sound Mode is set to User.
Treble
Press the ▲▼ button to select Treble and press the ◄► button to adjust the level.
Bass
Press the ▲▼ button to select Bass and press the ◄► button to adjust the level.
Balance
Press the ▲▼ button to select Balance and press the ◄► button to adjust the level.
Auto Volume
Occasionally, different TV stations volume level may be different from each other, this function will
mornalise audio level form all channels.
Press the ▲▼ button to select Auto Volume and press the ◄► button to select On or Off.
Surround Sound
Press the ▲▼ button to select Surround Sound and press the ◄► button to select Surround or
Off.
Spdif
Press the ▲▼ button to select Spdif and press the ◄► button to select Off, RAW or PCM.
- -
26
TV Function
Time Setting
Press the MENU button once to enter CHANNEL
setup menu and press the ▲▼ button to select
TIME, the screen will display as shown.
Press the ENTER or ► button to enter the menu.
In the TIME setup menu, press the ▲▼ button to
select the desired item. Press the MENU button to
return to the previous menu. Press the EXIT button
to exit.
Clock
Press the ▲▼ button to select Clock and press the
► button or ENTER button to prompt a information
box, as shown:
Press the ▲▼ button to select Date, Month, Year,
Hour or Minute, press the ◄► button to set.
Press the ENTER button to confirm after selecting
Close.
NOTE: in DTV mode, the Clock function is not available when there is DTV signal input.
Off Time
Press the ▲▼ button to select Off Time and press
the ENTER or ► button to prompt a information
box, as shown:
Press the ▲▼ button to select Repeat, Hour or
Minute, press the ◄► button to set.
Press the ENTER button to confirm after selecting
Close.
Sleep Timer
Press the ▲▼ button to select Sleep Timer and press the ◄► button to select the time to turn off
the TV.
Auto Sleep
Press the ▲▼ button to select Auto Sleep and press the ◄► button to select On or Off.
Time Zone
Press the ▲▼ button to select Time Zone and press the ◄► button to select desired time zone.
- -
27
TV Function
Option Setting
Press the MENU button once to enter CHANNEL
setup menu and press the ▲▼ button to select
OPTION, the screen will display as shown.
Press the ENTER or ► button to enter the menu.
In the OPTION setup menu, press the ▲▼ button
to select the desired item. Press the MENU button
to return to the previous menu. Press the EXIT
button to exit.
Language
Press the ▲▼ button to select Language and press the ◄► button to select desired language.
Audio Languages
Press the ▲▼ button to select Audio Languages
and press the ENTER or ► button to prompt a
information box, as shown:
Press the ▲▼ button to select Primary or
Secondary, press the ◄► button to select desired
language.
Press the ENTER button to confirm before
selecting Close.
Subtitle Language
Press the ▲▼ button to select Subtitle Language
and press the ENTER or ► button to prompt a
information box, as shown:
Press the ▲▼ button to select Primary or
Secondary, press the ◄► button to select desired
language.
Press the ENTER button to confirm after selecting
Close.
Hearing Impaired
Press the ▲▼ button to select Hearing Impaired and press the ◄► button to select On or Off.
- -
28
TV Function
Country
This item is used to shown the current country.
Restore Factory Default
Press the ▲▼ button to select Restore Factory
Default and press the ENTER or ► button to
prompt a confirmation information box, as shown:
Press the ◄► button to highlight Yes or No, press
the ENTER button to reset the settings to their
default status or cancel.
Note: this will delete all changes and user setting.
- -
29
EPG Function
In DTV mode, press the EPG button to display the CHANNEL GUIDE menu as shown below:
Within this menu, press the ▲▼ button to select a desired channel.
Press the DISPLAY button to display the detail information of the selected channel.
Press the yellow button to check the date information.
Press the green button to display the Schedule List as shown below:
Within the SCHEDULE LIST menu, press the ▲▼ button to select desired item and press the red
button to delete it. Press the EXIT button to exit.
Press the blue button in the CHANNEL GUIDE menu
to enter the Reminder menu, as shown on the right:
Within this menu, press the ▲▼ button to select
desired item and press the ◄► button to set.
Press the green button to display the Schedule List.
Press the ENTER button to save your settings.
Press the EXIT button to exit.
- -
30
NICAM Function
The unit supports NICAM function when in TV mode.
Under NICAM TV broadcast:
1. When receiving stereo audio signals, press the STEREO button on the remote control
repeatedly to select the sound tracks between NICAM STEREO and Mono and the screen will
show the corresponding display as shown below:
2. When receiving bilingual audio signals, press the STEREO button on the remote control
repeatedly to shift the sound tracks between NICAM DUAL I, NICAM DUAL II, NICAM DUAL
I+II and Mono and the screen will show the corresponding display as shown below:
3. When receiving mono audio signals, press the STEREO button on the remote control
repeatedly to shift the sound tracks between NICAM Mono and Mono and the screen will show
the corresponding display as shown below:
Under A2 TV broadcast:
1. When receiving stereo audio signals, press the STEREO button on the remote control
repeatedly to shift the sound tracks between Stereo and Mono and the screen will show the
corresponding display as shown below:
2. When receiving bilingual audio signals, press the STEREO button on the remote control
repeatedly to shift the sound tracks between DUAL I, DUAL II and DUAL I+II and the screen
will show the corresponding display as shown below:
3. When receiving mono audio signals, press the STEREO button on the remote control to display
sound track Mono on the screen.
- -
31
DVD Playback Operation
Preparation
1. Connect the unit to the power supply and press the POWER button to turn on the unit.
2. Repeatedly press the INPUT button on the remote control to select DVD mode and press the
ENTER button to enter.
3. Gently insert the disc, with the label side toward the front of the television, into the disc tray slot
until about half of the disc is in the tray and then the disc will be drawn into the disc tray and
loaded automatically.
note: must select DVD mode before insert disc.
4. Press the
EJECT button to eject the disc, but the disc can not be drawn into the disc tray by
pressing the
EJECT button again. You must push the disc until it is drawn into the disc tray
automatically.
Warning: Use of poor quality discs could result in damage to the television.
DVD Playback
Region Code
DVD players and discs are coded by region. These regional codes must match the played discs. If
the codes don’t match, the disc cannot be played. This player’s default code is 4.
Play
Press the PLAY button to start playback.
Stop
During playback, press the ■ STOP button once to stop playback and press the ► PLAY button to
resume normal playback. Press the ■ STOP button twice to stop playback completely.
Pause
During playback, press the PAUSE button once to pause the playback; press it repeatedly to start
step-by-step playback. Press the ► PLAY button to resume normal playback.
- -
32
DVD Playback Operation
Previous and Next
Press the button to go to the next chapter. Press the button once to return to the beginning of
the current chapter or track; press it twice to go to the previous chapter.
Fast Playback
During playback, press the button to activate fast backward or forward playback. During fast
playback, press the ► PLAY button to resume normal playback.
Repeat
Press the REPEAT button repeatedly to repeat a chapter, title or all.
• Some discs do not support the repeat function.
Menu
Normally there is a selecting menu for DVD discs. You can press the MENU button (under DVD
mode) to enter the menu, and use the direction buttons to highlight an item. Then press the ENTER
button to confirm.
Title & Chapter
Normally there are several titles in a DVD disc, and several chapters (sections) in a title. Press the
TITLE button to enter the title menu, and you can select any title or chapter quickly by entering the
relevant number.
• Some discs do not support the function by inputting the number button but the ▲▼◄►
direction buttons.
Language (Audio)
There can be up to 8 audio languages on a DVD disc. When you play a multi-language DVD disc
you can use the AUDIO button on the remote control to select a desired language.
GOTO
During DVD disc playback, press the GOTO button on the remote control once, there will be a
menu displayed on the screen. You can set or select items for your preference. Use the ▲▼
direction buttons to select items and press the ENTER button to enter and use the ▲▼ direction
buttons to select the desired item. Press the ◄ direction button to return. When selecting the
Title/Chapter, TT Time/CH Time, use the number buttons to input the desired title/chapter, time.
• Some DVD discs do not support the search function.
Subtitle
The DVD player can support multiple kinds of subtitles. When you play a multi-subtitle disc you can
press the SUBTITLE button on the remote control to select different subtitles.
• Some discs do not support the shifting subtitle function.
- -
33
DVD Playback Operation
CD Playback
The player will play all tracks on a CD disc by default. You can use the buttons, or number
buttons to select a track.
Stop
Press the ■ STOP button once to stop playback and press the ► PLAY button to resume normal
playback. Press the ■ STOP button twice to stop playback completely.
Pause
Press the PAUSE button to pause the playback and then press the PAUSE button again or ►PLAY
button to resume normal playback.
Previous and Next
Press the button to go the beginning of the current track. Press twice repeatedly to go the
previous track.
Press the button to play from the beginning of the next track.
Fast Playback
Press the button on the remote control to activate fast backward or forward playback.
Repeat
Press the Repeat button repeatedly to repeat a single track, all tracks, or to exit repeat mode.
• Some discs do not support the repeat function.
Audio
During playback, press the Audio button to toggle audio output between Mono Left, Mono Right,
Mix-Mono or Stereo.
GOTO
Press the GOTO button to access the time-selected state. You can select Disc Go To, Track Go To
or Select Track respectively by pressing this button repeatedly. Use the 0-9 buttons to enter the
desired time and then the player will play according to the selected time. Use the 0~9 number
buttons and the +10 button to enter the desired track number, then the player will play the selected
track.
- -
34
DVD Playback Operation
JPEG Playback
JPEG is a common picture format that requires small amounts of storage per image and has low
loss in resolution. Hundreds of pictures can be stored on a disc in this format. In order to view JPEG
photo albums, you can ask your film development company to make a ”PICTURE CD” when they
develop your film.
Normal Playback
Load a JPEG disc in. For JPEG disc, there will be a root menu displayed on the screen. Use the
ENTER button and the direction button to select a submenu, and then use the ▲▼◄► direction
button to select the contents. Many discs have other contents besides pictures.
For Picture CD disc, it will display the pictures automatically.
During playback, press the button to select the picture.
• Many discs have other contents besides pictures.
Stop
Press the ■ STOP button to preview the pictures behind currently playing picture in the way of small
pictures. Press the ► PLAY button to resume normal playback.
Pause
Press the PAUSE button to pause playback, press the PAUS E button again or ► PLAY button to
resume playback.
Repeat
During playback, press the REPEAT button repeatedly, and the repeat modes are Shuffle, Random,
Single, Repeat One, Repeat All and Repeat Off.
Menu
Press the MENU button once to stop playback and return to the root menu.
GOTO
During playback, press the GOTO button on the remote control once, use the number buttons to
input the file number.
Picture Rotation
During playback, press the ◄► button to rotate the currently displayed picture. This function only
activates for the current picture; once another picture is displayed, rotation will be cancelled
automatically.
• Note: Some JPEG discs may not support the rotation function.
- -
35
DVD Playback Operation
DIVX Playback
DIVX is the name of a revolutionary new video code, which is based on the new DIVX compression
standard for video.
1. Load a DIVX disc in the disc tray, the player will enter the reading mode.
2. The screen displays the root menu. Use the ▲▼ buttons to select desired item and press the
ENTER button to play.
Stop
During playback, press the ■ STOP button to stop playback and return to root menu and press the
► PLAY button to play the file from the beginning.
Pause
During playback, press the PAUSE button once to pause the playback and press it again or press
the ► PLAY button to resume normal playback.
Previous and Next
Press the button to go the previous file; press the button to play the next file
Fast Playback
During playback, press the button to activate fast backward or forward playback. During fast
playback, press the ►PLAY button to resume normal playback.
REPEAT
During playback, press the REPEAT button repeatedly to select repeat mode.
GOTO
Press the GOTO button repeatedly to select Select:--- or Go To:-:--:--. Use the 0-9 buttons to enter
the desired time or and then the player will play according to the selected time. Use the 0~9 number
buttons and the +10 button to enter the desired track number, then the player will play the selected
track.
- -
36
USB and SD/MS/MMC Card Function
Preparation
In DVD mode, connect USB device to the USB port or insert SD/MS/MMC card into the
SD/MS/MMC card slot on the right side of the unit.
¾ Make sure that files are stored in the USB and SD/MS/MMC card before connection.
1. Press the CARD button to shift between Disc playback, USB playback and SD/MS/MMC
playback. The default state is disc playback. Please see the figure below:
2. Press the ▲▼ buttons to select the folder. Press the ENTER button to enter.
3. Press the ▲▼ buttons to select the desired track. Then press the PLAY ► button to start
playback.
4. Press the STOP button to stop playback. Press the ◄ button to return to the folder menu.
Note:
1. The screen display will vary from disc to disc.
2. Pull out the USB or SD/MS/MMC card directly after finished playback. The unit will now return
to disc playback mode.
00:00 00:00
001/002
BAK
JPEG
- -
37
DVD System Setup
Preparation
1. In DVD mode, press the SETUP button to enter DVD system setup menu.
2. Press the ◄► button to select setup menu.
3. Press the SETUP button again to exit DVD system setup menu.
General Setup Page
Press the SETUP button to enter the General Setup Page. The screen will display as below:
TV Display
Angle Mark
On the menu, use the ▲▼ direction buttons to
select the desired item. Press the ENTER button to
enter the item. Press the ◄ button to return.
1. Press the ▲▼ direction buttons to select TV
Display.
2. Press the ENTER button to enter the setup.
3.
Use the ▲▼ direction buttons to select items.
4.
Press the ENTER button again to confirm
selection and return.
1. Press the ▲▼ direction buttons to select
Angle Mark.
2. Press the ENTER button to enter the setup.
3. Use the ▲▼ direction buttons to select On or
Off.
4. Press the ENTER button again to confirm
selection and return.
- -
38
DVD System Setup
OSD Lang
Captions
Screen Saver
Last Memory
1. Press the ▲▼ direction buttons to select OSD
Lang.
2. Press the ENTER button to enter the setup.
3.
Use the ▲▼ direction buttons to select desired
OSD language.
4.
Press the ENTER button again to confirm
selection and return.
1. Press the ▲▼ direction buttons to select
Screen Saver.
2. Press the ENTER button to enter the setup.
3.
Use the ▲▼ direction buttons to select On or
Off.
4.
Press the ENTER button again to confirm
selection and to return.
1. Press the ▲▼ direction buttons to select Last
Memory.
2. Press the ENTER button to enter the setup.
3. Use the ▲▼ direction buttons to select On or
Off.
4. Press the ENTER button again to confirm
selection and return.
1. Press the ▲▼ direction buttons to select
Captions.
2. Press the ENTER button to enter the setup.
3.
Use the ▲▼ direction buttons to select On or
Off.
4.
Press the ENTER button again to confirm
selection and return.
- -
39
DVD System Setup
Audio Setup Page
Press the SETUP button to enter the General setup menu, then use the ◄► direction buttons to
select Audio Setup Page, the screen will display as the below:
Dolby Digital Setup
Press the ▲▼ direction buttons to select Dolby Digital in the Audio Setup Page and press the
ENTER button to enter the setup.
Dual Mono
Dynamic
On the menu, Use the ▲▼ direction buttons to
select the desired item. Press the ENTER button to
enter the item. Press the ◄ button to return.
1. Press the ▲▼ direction buttons to select Dual
Mono.
2. Press the ENTER button to enter the setup.
3.
Use the ▲▼ direction buttons to select items.
4.
Press the ENTER button again to confirm
selection and return.
1. Press the ▲▼ direction buttons to select
Dynamic.
2. Press the ENTER button to enter.
3. Use the ▲▼ direction buttons to adjust.
4.
Press the ENTER button again to confirm
setting and return.
5.
Press the ◄ button to return.
- -
40
DVD System Setup
HDCD Setup
In the Audio Setup Page, use the ▲▼ direction buttons to select HDCD Setup. Press the ENTER
button to enter the menu as shown below:
Video Setup
Press the SETUP button to enter the General setup menu, then use the ◄► direction buttons to
select Video Setup Page, the screen will display as the below:
Video Quality Setup
Select Quality in the Video Setup Page and press the ENTER button to enter the menu. Within this
menu, press the ▲▼ direction buttons to select desired item.
Sharpness
1. On the menu, press the ENTER button to enter
the setup.
2. Use the ▲▼ direction buttons to select items.
3.
Press the ENTER button again to confirm
selection and return.
4.
Press the ◄ button to return.
On the menu, Use the ▲▼ direction buttons to
select the desired item. Press the ENTER button to
enter the item. Press the ◄ button to return.
1. Press the ▲▼ direction buttons to select
Sharpness.
2. Press the ENTER button to enter the setup.
3. Use the ▲▼ direction buttons to select High,
Medium or Low.
4. Press the ENTER button again to confirm
selection and return.
- -
41
DVD System Setup
Brightness
Contrast
DivX VOD Setup
Select DivX VOD, press the ENTER button to enter the menu as shown:
Preference Setup
Press the SETUP button to enter the General setup menu, then use the ◄► direction buttons to
select Preference Page, the screen will display as the below:
1. Press the ▲▼ direction buttons to select
Brightness.
2. Press the ENTER button to enter the setup
3. Use the ◄► direction buttons to adjust the
level.
4. Press the ENTER button again to confirm
setting and return.
1. Press the ▲▼ direction buttons to select
Contrast.
2. Press the ENTER button to enter the setup.
3. Use the ◄► direction buttons to adjust the
level.
4. Press the ENTER button again to confirm
setting and return.
Note:
Your registration code is: XXXXXX.
Please use this code to register this player with the
DivX(R) video On Demand Service.
This will allow you to rent and purchase videos
using the DivX(R) video On Demand format. To
learn more go to www.divx.com/vod.
On the menu, Use the ▲▼ direction buttons to
select the desired item. Press the ENTER button to
enter the item. Press the ◄ button to return.
- -
42
DVD System Setup
Audio
Subtitle
Disc Menu
Default
1. Press the ▲▼ direction buttons to select
Audio.
2. Press the ENTER button to enter the setup.
3. Press the ▲▼ direction buttons to select audio
language.
4. Press the ENTER button again to confirm
setting and return.
1. Press the ▲▼ direction buttons to select
Subtitle.
2. Press the ENTER button to enter the setup.
3. Press the ▲▼ direction buttons to select
Subtitle language.
4. Press the ENTER button again to confirm
setting and return.
1. Press the ▲▼ direction buttons to select Disc
Menu.
2. Press the ENTER button to enter the setup
3. Press the ▲▼ direction buttons to select Menu
language.
4. Press the ENTER button again to confirm
setting and return.
1. Press the ▲▼ direction buttons to select
Default.
2. Press the ENTER button to select Reset.
3. Press the ENTER button, all the settings will
return to the default status.
- -
43
Troubleshooting
SYMPTOM CHECK ITEM
The player cannot play.
Make sure the disc is loaded in.
Make sure the disc is not dirty or warped.
Make sure the player’s region code is the same as the region
code of the DVD disc.
Make sure water condensation has not occurred. If it occurs,
take out the disc and leave the player on for at least one
hour.
There is no sound.
Make sure the system connection is correct.
Make sure the sound setup of the DVD disc is correct.
Make sure the disc is not dirty or warped.
Clean or replace the disc.
Make sure the speakers are not muted.
In the TV mode, set the correct sound mode.
LCD has no display
Make sure the unit is turned on and the connections are
correct.
Make sure the power adapter is correctly connected.
Cannot continue to play and
play a section repeatedly.
Make sure it is not in repeat status.
Make sure the disc is not dirty or damaged.
There is no picture or picture
jitters up and down Unsteady.
Check if the connections with the external AV signal source
are correct.
Correctly set the items in the picture menu.
Check if the video type input signal is not corresponding to
the unit.
Make sure the unit is turned on and in the correct video type.
The remote control does not
work.
Make sure there are no obstructions between the remote
control and the player.
Make sure the remote control is pointing at the player.
Make sure the batteries are inserted and the polarity is
correct.
Make sure the battery is not weak.
Other Notes:
Static or other external interference may cause the player to behave abnormally. If this occurs,
unplug the power-supply cord from the outlet and plug it in again to reset the player. If the problems
persist, then please disconnect the power and consult a qualified technician.
- -
44
Specifications
Model LCDV2655HD
Screen Size 26-inch TFT LCD TV
Native Resolution 1366×768 Pixels
Brightness 400cd/m2
Contrast Ratio 800 :1
Response time (ms) 8ms
Color System PAL
Sound System BG/I/DK
Tuner VHF/UHF: 48.25~863.25MHz
Antenna 75Ω VHF/UHF input
Stereo NICAM/A2
VIDEO INPUT
CVBS input PAL/SECAM/NTSC
S-VIDEO input
Y/C separate video signal Y...1 Vp-p/negative sync/75Ωinput C...0.283
Vp-p/75Ωinput(NTSC) 0.3 Vp-p/75Ωinput(PAL)
COMPONENT
RCA,0.7Vp-p/75Ω input
(480I/60Hz,480P/60Hz,576I/50Hz,576P/50Hz,720P/50Hz,720P/60Hz,1
080I/50Hz,1080I/60Hz, 1080P/50Hz, 1080P/60Hz)
HDMI 1080i, 720p, 1080p
Audio in RCA audio input
OTHERS
DVD Player DVD+/-RW, DVD-R, CD, CD-R, CD-RW, JPEG, DivX 3.11/4.x/5.x/6.x
Multi Media USB Card Reader
MS, SD, MMC 3 in 1 Card reader and USB compatible
Max Volume up to 2GB
VGA
15 Pin, Analog RGB signal, 0.7Vp-p, 75Ωinput(VGA, SVGA, XGA,
WXGA computer signal compatibility),
1440*900@60Hz
, 1024*768@60Hz, 800*600@60Hz, 640*480@ 60Hz
Teletext 1000 pages
TV SET OUT
AV output monitor
Speaker Output 8W+8W
Power Requirement AC100 to 240V, 50/60Hz
Power Consumption < 120W
Standby Power < 1W
Dimension(with stand) 667mm × 235mm × 500mm（W × D × H）
Dimension(without stand) 667mm ×100mm × 454mm（W × D × H）
Net Weight About 13.5 Kg
Ambient Temperature 10~45℃
Note: Specifications subject to change without pre-notice. Weight and dimensions are approximate.
TEAC AUSTRALIA PTY.,LTD.
A.B.N.: 11 113 998 048
Service Providers in Australia
please contact one of the following service providers in your area if you require service for your product.
Name Address Phone Fax
Associated Electronics 7 Molonglo Mall FYSHWICK 2609 (02)62 80 4698 (02)62 80 5437
TEAC Perth Service Centre 273 Great Eastern Highway BELMONT 6104 (08)94 79 6499 (08)94 79 6544
Inpulse Electronics 3 Sloane Street MARIBYRNONG 3032 (03)93 17 4000 (03)39 17 4040
Jav Electronics 65 Mackie Road BENTLEIGH EAST 3165 (03)95 70 4911 (03)95 63 8722
Watpace Electronics 62 Wingara Avenue KEILOR EAST 3033 (03)93 36 4042 (03)93 36 3768
QQ Electronics Pty Ltd Unit 5, 14-38 Bellona Avenue REGENTS PARK 2143 1300 883 229 (02)97 38 1311
Maxwell Electronics 106 Bath Road KIRRAWEE 2232 (02)95 42 3000 (02)95 42 3377
TCS (Total Care Services) 62 Leader Street FORESTVILLE 5035 (08)83 51 1044 (08)83 51 1043
NSW
Name Address Phone Fax
B & H Electronics 466 David Street ALBURY 2640 (02)60 41 3911 (02)60 21 7455
Border Video & TV Service Shop 3, 339 Urana Road LAVINGTON 2641 (02)60 40 2229 (02)60 40 2184
Bourkes Video & Tv Service 111 Danger Street ARIMDALE 2350 (02)67 71 1513 (02)67 71 1696
Nichols Electronics Shop 4/70 River Street BALLINA 2478 (02)66 86 9422 (02)66 81 4999
Baytech Electronics Shop 3, 270 Beach Road BATEHAVEN 2536 (02)44 72 7023 (02)44 72 7354
Sapphire Electronics U5B/85 Bega Street BEGA 2550 (02)64 92 2522 (02)64 93 2062
Lawson Radio & TV 298 Great Western Highway LAWSON 2783 (02)47 59 1254 (02)47 59 2312
Iwac Repairs Pty Ltd Shop 8, 12 Statham Street BENNETTS GREEN 2290 (02)49 48 1067 (02)49 48 1069
Visual Audio Services 510 Chapple Street - PO BOX 76 BROKEN HILL 2880 (08)80 87 4055 (08)80 87 4055
T K Electronics Unit 2 10 O’Hart Close CHARMHAVEN 2263 (02) 43 92 0828 (02)43 93 1018
TV Technologies 20 Marcia Street COFFS HARBOUR 2450 (02)66 51 7366 (02)66 50 0152
Coogee Electronic Service 261 Arden Street COOGEE 2034 (02)93 15 8566 (02)66 50 0152
Electronics 2000 Shop 3/190 Sharp Street COOMA 2630 (02)64 52 4179 (02)64 52 4179
Lachlan Valley TV 49 Vaux Street COWRA 2794 (02)63 42 2189 (02)63 42 2189
Greg’s TV 2 Bingalong Street DALMENY 2546 (02)44 76 7544 (02)44 76 7544
Deniliquin Hi-Tech 44 Hardinge Street DENILIQUIN 2710 (03)58 81 1444 (03)58 81 1444
Western Electronic Service 437 Hopkins Parade DUBBO 2830 (02)68 82 3905 (02)68 82 3870
Con Carr Retravision 126-128 Murray Street FINLEY 2713 (03)58 83 1611 (03)58 83 2114
Forbes TV & Video Repairs 132 Rankin Street FORBES 2871 (02)68 52 2921 (02)68 52 2921
Forster Electronic Services Shop 15, Forster Tower, Wallis Street FORSTER 2428 (02)65 54 5352 (02)65 54 5352
V.J. & C.M. Davey TV & 137 Meade Street GLEN INNES 2370 (02)67 32 2260 (02)67 32 2260
Ray White Television Repairs 2 Taylor Street GOULBURN 2580 (02)48 22 4050
Repairs & Spares 140 Fitzroy Street GRAFTON 2460 (02)66 42 1911 (02)66 43 3961
Griffith Home Appliance 94-98 Yambil Street GRIFFITH 2680 (02)69 62 1826
S & K Electronics 111 Banna Avenue GRIFFITH 2680 (02)69 62 2847 (02)69 64 7774
Ron Burns Electrical 8 Hillcrest Road GUNNEDAH 2380 (02)67 42 3299
Tele – Fridge Electronics 82 Conadilly Street GUNNEDAH 2380 (02)67 42 0022 (02)67 42 3878
R
Inverlec Electronics Shop 1,20 Glen Innes Road INVERELL 2360 (02)67 22 4522 (02)67 22 4522
Maxwell Electronics 106 Bath Road KIRRAWEE 2232 (02)95 42 3000 (02)95 42 3377
Jag Electronics 59 Tambourine Bay Road LANE COVE 2066 (02)94 27 5478 (02)94 28 2634
AVL Electronics 2/87 Bold Street LAURIETON 2443 (02)65 59 6330 (02)65 59 6330
Leeton Appliances 99 Grevillia Street LEETON 2705 (02)69 53 4151 (02)69 53 4151
Hans Electronic Services 147 Magellan Street LISMORE 2480 (02)66 21 9311 (02)66 21 9711
Robert Peatfield 2 West Street MACKSVILLE 2447 (02)65 68 2867 (02)65 68 2867
Mullumbimby TV Service Shop 3 97-99 Stuart Street MULLUMBIMBY 2482 (02)66 84 2335 (02)66 84 3554
John Rice TV Service 13 Park Avenue MURWILLUMBAH 2484 (02)66 72 3292 (02)66 72 3292
Spencer Electronics Unit 2, 26 Somerset Avenue NARELLAN 2567 (02)46 47 2046 (02)46 47 2046
Newcastle Quickfix/ J P Electronics Shop 5, 468 Pacific Hwy BELMONT 2280 (02)49 45 4699 (02)49 45 5696
NSW
Name Address Phone Fax
Videotel Unit 1/17 Quinns Lane SOUTH NOWRA 2541 (02)44 21 5250 (02)44 23 3280
Ideal Electronics 145 Woodward Street ORANGE 2800 (02)63 62 8270 (02)63 62 8270
Parkes Sight 'n' Sound 67 Clarinda Street PARKES 2870 (02)68 62 4475 (02)68 63 4209
Vickery Sound 171 Brisbane Water Drive POINT CLARE 2250 (02)43 23 3623 (02)43 23 1581
Quickfix Repairs 118 Stafford Street PENRITH 2750 (02)47 22 8550 (02)47 22 9949
BJRAE Electronics 2/199 Adelaide Street RAYMOND TERRACE 2324 (02)49 87 7032 (02)49 87 6194
QQ Electronics Pty Ltd Unit 5, 14-38 Bellona Avenue REGENTS PARK 2143 1300 883 229 (02)97 38 1311
Quickfix Repairs Shop 17 West Market Street RICHMOND 2754 (02)45 78 2111 (02)45 78 2021
Tech 1 Electronic Repairs Shop1/12 Sunset Ave WARILLA 2528 (02)42 97 5397 (02)42 97 5398
Cherries Electronics Unit 3, 8 Walter Street SINGLETON 2330 (02)65 71 2488 (02)65 71 2488
Videtel Video, TV & Monitor 232 Marius Street EAST TAMWORTH 2340 (02)67 61 3788 (02)67 61 3388
Peel Television Service 1 Macquarie Street TAMWORTH 2340 (02)67 66 3928 (02)67 66 9932
Colour Fix TV & Video Service 172 Bridge Street TAMWORTH WEST 2340 (02)67 65 5539 (02)65 62 0561
Hawkins Electronic Service 94 Manning Street TAREE 2430 (02)65 52 2288 (02)65 52 4059
Household Electronics 3/39 Shearwater Drive TAYLORS BEACH 2316 (02)49 19 0344 (02)49 19 0355
That Repair Shop 122 Fitzmaurice Street WAGGA WAGGA 2650 (02)69 21 5200 (02)69 25 9491
Schuberts Electronics 53 Hastings Street WAUCHOPE 2446 (02)65 85 1533 (02)65 85 3816
ILLAWARRA Electronics Solution Shop 3, 60 Lakeside Drive KANAHOOKA 2530 (02)42 61 9234 (02)42 61 9227
United Television Service Pty Ltd 390 Keira Street WOLLONGONG 2500 (02)42 28 4555 (02)42 26 3453
Vac Shak Pty Ltd 16 Lovell Street YOUNG 2594 (02)63 82 5700 (02)63 82 7366
QLD
Name Address Phone Fax
McMahon Electrical Traders 23 Mabel Street ATHERTON 4883 (07)40 91 1788 (07)40 91 1741
Beerwah Electronics Peachester Road BEERWAH 4519 (07)54 94 0466 (07)54 94 0416
Bremer Television Service 36 Station Road BOOVAL 4304 (07)32 82 3593 (07)32 82 1214
Bowen Retravision (Northern Elect) 40 George Street BOWEN 4805 (07)47 86 1633 (07)47 86 2257
TV Doctor Unit 2, 11 Breene Place MORNINGSIDE 4170 (07)38 99 9644 (07)33 99 9019
Telefix Unit 9, 19 Lensworth Street COOPERS PLAINS 4108 (07)33 23 2700 (07)33 23 2730
Nielsons Radio & TV Service 68 Gavin Street BUNDABERG 4670 (07)41 53 1377 (07)41 53 1534
A1 Sound & TV Service 14 Gloucester Road BUDERIM 4556 (07)54 45 4777 (07)54 45 1311
Caboolture Video & Microwave 4/125 Morayfield Road CABOOLTURE 4510 (07)54 95 3477 (07)54 95 3477
Digital TV Service 197 Lyons Street WESTCOURT 4870 (07)40 51 1711 (07)40 51 1771
Garrows Video & TV Service 4/74 Omrah Avenue CALOUNDRA 4551 (07)54 91 3238 (07)54 91 7457
Charleville Radio & TV 14 Wills Street CHARLEVILLE 4470 (07)46 54 1633 (07)46 54 2266
Moss Electronics (form Caboolture Video) Unit 2, 25 Redcliffe Gardens Dr CLONTARF 4019 (07)3283 6749 (07)3283 6750
Precise Electronics 1 / 4 Northview Street MERMAID BEACH 4218 (07)55 75 1377 (07)55 72 4689
Ready Electronics Shop 3/1 Tibbing Street NERANG 4211 (07)55 96 6359 (07)55 02 2734
Tweed Television Shop 3/12 Machinery Drive SOUTH TWEED HEADS 2486 (07)55 24 4483
Bakers TV & Electronics Pty Ltd Unit 15, 388 Newman Road GEEBUNG 4185 (07)32 16 5495 (07)32 16 5598
Harbour City TV & Video Shop 3/1 Mellefont Street GLADSTONE 4680 (07)49 72 9495 (07)49 72 9495
Lloyd Lawrence Electronics Shop 8-9, 5 Torquay Road HERVEY BAY 4655 (07)41 24 3787 (07)41 24 3787
Professional VCR Sales Service 90 Mourilyan Road INNISFAIL 4860 (07)40 61 4720 (07)40 61 4720
Dunstans SBTV 37 Kingaroy Street KINGAROY 4619 (07)41 62 1547 (07)41 62 2343
Nev Robert Electronics 31 Hart Street MACKAY 4740 (07)49 57 6498 (07)49 51 3737
Sunland TV Service Unit 5 Centre One, Norval Court MAROOCHYDORE 4558 (07)54 43 6444 (07)54 43 6464
Telefix Unit 1, 96 Aerodrome Road MAROOCHYDORE 4558 (07)33 23 2700 (07)33 23 2730
Noosa TV & Video Repairs Shop 2, 9 Commerce Court NOOSAVILLE 4566 (07)54 47 1752 (07)54 47 1753
Sunland TV Service Shop 4, 54 Rene Street NOOSAVILLE 4566 (07)54 74 2101
Cumners Electronics Shop 4, 131 Old Pacific Highway OXENFORD 4210 (07)55 73 5250 (07)55 73 5403
N & M TV & Video Service 47a Yandilla Street PITTSWORTH 4356 (07)46 93 2886 (07)46 93 2886
C.Q. Video & TV Service 227 Berserker Street ROCKHAMPTON 4701 (07)49 28 8811 (07)49 28 2698
Matthew's TV & Video Service 176 Main Street ROCKHAMPTON 4701 (07)49 28 5377 (07)49 28 5608
WSR Electronics 542 Sherwood Road SHERWOOD 4075 (07)33 79 5400 (07)32 78 5655
Top Beat Entertainment & Elec 97A Folkestone Street STANTHORPE 4380 (07)46 81 0681 (07)46 81 0682
T.I. TV Repairs 11 Summer Street THURSDAY ISLAND 4875 (07)40 90 2139 (07)40 69 2577
Clark & Webb TV & Radio 14 Grange Street TOOWOOMBA 4350 (07)46 32 7290 (07)46 32 9244
Downs Radio & TV Service (DR TV) 35 Dent Street TOOWOOMBA 4350 (07)46 32 1044 (07)46 32 1224
Townsville Electronics 197 Ingham Road WEST END 4810 (07)47 75 7774 (07)47 79 6867
Top Beat Entertainment & Electrical 46 Wood Street WARWICK 4370 (07)46 61 2690
NT
Name Address Phone Fax
The Television Workshop Shop 4 Elder St Centre ALICE SPRINGS 0870 (08)89 52 8555 (08)89 52 5557
New Age Electronics Unit 1/21 Delatour Street COCONUT GROVE 0810 (08)89 48 1755 (08)89 48 1766
Eletech Service 13 Sandalwood Ave NHULUNBUY 0880 (08)89 87 3828 (08)89 87 3828
SA
Name Address Phone Fax
TCS (Total Care Services) 62 Leader Street FORESTVILLE 5035 (08)83 51 1044 (08)83 51 1043
Haynes Electronic Service Shop 3, 7 Verrall Cresent BERRI 5343 (08)85 82 4677 (08)85 82 5294
E.K. Dunstan & Co 255 Main Street CLARE 5453 (08)88 42 2144 (08)88 42 3942
Peter's Electronics 25 Lorna Street LOXTON 5333 (08)85 84 6920 (08)85 84 6920
Gambier Sound& Vision Repairs 16-18 Watson Tce MT GAMBIER 5290 (08)87 23 3955 (08)87 23 3855
Portside Technologies 28 Hallet Place PORT LINCOLN 5606 (08)86 82 1500
Pirie Antenna & TV 283B Senate Road PORT PIRIE 5540 (08)86 32 2565 (08)86 33 0091
Riverland Electronics Services 113 Renmark Avenue RENMARK 5341 (08)85 86 5600 (08)85 86 5533
Victor Electronic Service 44 Torrens Street VICTOR HARBOR 5211 (08)85 52 1471 (08)85 52 1098
Eyre Electronics 15B Forsyth Street WHYALLA 5600 (08)86 45 4764 (08)86 45 5576
TAS
Name Address Phone Fax
R.M Electronics 32 Strahan Street BURNIE SOUTH 7320 (03)64 31 8922 (03)64 31 89 22
Somerset Electronics 16 Douglas Street EAST DEVONPORT 7310 (03)64 27 0016
D.J. Hingston 95 James Road SPREIGHTON 7310 (03)64 27 2145 (03)64 27 2145
Integrated Components 54A Albert Road MOONAH 7009 (03)62 78 1932 (03)62 78 8387
K.T. National Electronics 1 Hobart Road SANDHILL 7249 (03)63 44 5665 (03)63 43 0466
VIC
Name Address Phone Fax
Border Video & TV Service 362 Griffith Road LAVINGTON 2641 (02)60 40 2229 (02)60 40 2184
Greene's Television Services 149 Hummfray Street BALLARAT 3350 (03)53 32 6256 (03)53 32 7597
Ted Rivett Services 145 Creswick Road BALLARAT 3550 (03)53 32 6371 (03)53 33 4002
Proud’s Hi Fi 78- 80 Pall Mall BENDIGO 3550 (03)54 42 2722 (03)54 42 2522
Jav Electronics 65 Mackie Road BENTLEIGH EAST 3165 (03)95 70 4911 (03)95 63 8722
B M Tronics 197 Murray Street COLAC 3250 (03)52 32 1504 (03)52 32 1935
Unitech Services 72 Maroondah Highway CROYDON 3136 (03)97 25 2222 (03)97 25 2804
T & C Electronics Service 31 Pegleg Road EAGLEHAWK 3556 (03)54 46 3000 (03)54 46 3022
Echuca TV & Video Service 1/7 Mitchell Street ECHUCA 3564 (03)54 80 7874
Fawkner TV Service 123 Jukes Road FAWKNER 3060 (03)93 59 5836 (03)93 59 5048
Central Appliance Service 222 Moorabool Street GEELONG 3200 (03)52 22 1418 (03)52 22 1418
RTD Services Pty Ltd 25-29 Fairlie Street GEELONG NORTH 3215 (03)52 78 9766 (03)52 78 3545
Linke Electrical Repairs 82 Londsdale Street HAMILTON 3300 (03)55 72 5788 (03)55 72 4090
Frank Ritchie Electrical P/L 9 Victoria Street KERANG 3579 (03)54 52 2908 (03)54 52 2908
Watpace Electronics 62 Wingara Avenue KEILOR EAST 3033 (03)93 36 4042 (03)93 36 3768
Harold Hurren 26 Fitzroy Street KILMORE 3764 (03)57 82 1327 (03)57 82 1487
Soundwave Electronics 2B Holt Street LEONGATHA 3953 (03)56 62 3665 (03)56 62 3665
Inpulse Electronics 3 Sloane Street MARIBYRNONG 3032 (03)93 17 4000 (03)39 17 4040
Sunshine Electronics Aust Shop 2, 17 Moore Street MOE 3825 (03)51 26 1110 (03)51 26 1275
Peninsula VCR Repairs
1/8 Virginia Street MORNINGTON 3931 (03)59 75 0800 (03)59 76 2300
Ferguson Electronics 116 Orange Avenue MILDURA 3500 (03)50 23 5846 (03)50 21 2690
Bensi TV Electrical Pty. Ltd. 128 Nicholson Street ORBOST 3888 (03)51 54 1454 (03)51 54 1344
G & R Video & TV Services Pty. 24 Dunkirk Avenue SHEPPARTON 3630 (03)58 21 0258 (03)58 21 8187
Inpulse Electronics 496 Whitehorse Road SURREY HILLS 3027 (03)93 17 4000 (03)98 36 5922
Swantronics 45 Campbell Street SWAN HILL 3585 (03)50 33 1633 (03)50 33 1287
Earl & Becker 4-26 Shakespeare Street TRARALGON 3844 (03)51 74 8454 (03)51 74 8454
Tellycare (Nugents) 105 Queen Street WARRAGUL 3820 (03)56 22 1102 (03)56 22 1102
John B. Electronics Shop 94 High Street WODONGA 3690 (02)60 56 1066 (03)57 28 7299
WA
Name Address Phone Fax
Albany TV Service Shop 8 35-37 Campbell Road ALBANY 6330 (08)98 41 1573 (08)98 42 5958
Excel Electronics 3 Newman Court NICKOL 6725 (08)91 44 1266 (08)91 44 1266
North West Electronics 42 Fredrick Street BROOME 6725 (08)91 92 5003 (08)91 92 6003
Elricks TV Service 62 Spencer Street BUNBURY 6230 (08)97 21 4047 (08)97 21 1161
Busselton TV & Video 65B Strelley Street BUSSELTON 6280 (08)97 54 4457 (08)97 54 4824
Electronic Plus Unit 3/11 Egan Street CARNARVON 6701 (08)99 41 3690 (08)99 41 3660
Esperance Communications 33 Norseman Road ESPERANCE 6450 (08)90 71 3344 (08)90 71 4545
Bird Electronics 14 Abraham Street GERALDTON 6530 (08)99 64 1631 (08)99 21 7584
Geraldton Radio & TV Service 26 Anzac Terrace GERALDTON 6530 (08)99 64 2777 (08)99 64 2776
Oz West Electronics 6/200 Winton Road JOONDALUP 6027 (08)93 00 1066
Printek Electronics 1 Lesueur Drive JURIEN BAY 6516 (08)96 52 1664 (08)96 52 1664
Kalgoorlie Electronics 395 Hannan Street KALGOORLIE 6430 (08)90 21 1420 (08)90 21 1420
J & P Electronics 3/88 Albany Hwy KOJONUP 6395 (08)98 31 1991 (08)98 31 1991
Tuckerbox Retravision White Gum Street/P.O. BOX 941 KUNUNNURRA 6743 (08)91 68 1100 (08)91 68 2491
Waytec Electronics Unit 3, 10 Thornborough Road MANDURAH 6210 (08)95 82 0882 (08)95 82 0352
Manjimup TV Service 88 Giblett Street / P.O. BOX 370 MANJUMUP 6258 (08)97 71 1598 (08)97 72 4025
Chris's TV & Satelite 66 Barrack Street MERREDIN 6415 (08)90 41 1484 (08)90 41 1484
G & J Suckling Radio & TV 1 Hale Street NARROGIN 6312 (08)98 81 2148 (08)98 81 3129
Proton 21A Charles Street NORTHAM 6401 (08)96 22 3168 (08)96 22 3168
TEAC Perth Service Centre 273 Great Eastern Highway BELMONT 6104 (08)94 79 6499 (08)94 79 6544
Charles Hunt Electronics 25 Brodie Court BALDIVIS 6171 (08)63 63 5593 (08)95 24 2890
Please find a more up to date list on our website www.teac.com.au
TEAC CUSTOMER CARE CENTRE (TCCC)
Free call: 1800 656 700
Between Monday to Friday – EST 9AM to 5PM
Loading...