Page 1
‰ 322 Quick Start guide
This Quick Start Guide is intended to help you use some of the functions of the
322 which may be unfamiliar to you.
Dubbing between decks 1 and 2
The 322 allows you to copy material between its two decks at either normal or high
speed (double speed).
1
2
1
Load the source cassette into Deck 1 and the target into
deck 2. Locate to the appropriate position on both tapes.
Use the
appropriate to help you.
PHONES control, switching between 1 and 2 as
4
3
7
5
6
2 Set the 322 to dub either on one side (Ä) or both (ä)
side of the tape, using the
REV MODE switch.
3 Select either HI SPEED (double-speed) dubbing or NORM
(normal speed) dubbing, using the
standby) buttons. Pressing either of these buttons also puts
both decks into ready mode (Deck 1 is in play ready, and
Deck 2 is in record ready).
DUB STDBY (dubbing
4 If double-sided copying is already selected, select SYNC
REVERSE
time, even if the tapes are different lengths.
to start the second side of each tape at the same
5 Press the (forward) PLAY button on Deck 2 to start the
dubbing (Deck 1 plays and Deck 2 records).
6 In normal-speed mode, pause both decks by pressing
PAU SE on Deck 2; pressing PAU SE , STOP, F FWD or
REW on Deck 1 puts Deck 2 into record pause.
7 Stop dubbing by pressing Deck 2 STOP (normal and high-
speed) or Deck 1
STOP (high-speed only).
9101440800
Page 2
‰ 322 Quick Start guide
Continuous playback using both decks
One of the useful features of the 322 is the ability to play back continuously, using
both decks, allowing long programs of background music to be played back using
only one unit.
3
1
4
Both decks can share one set of outputs, or each deck can
1
use separate outputs. For separate outputs, make separate
connections to different amplifier/speaker systems. For
shared outputs, use Deck 1’s outputs.
Set the
put) or
2
5
INPUT/OUTPUT switch to COMMON (shared out-
SEPARATE (separate outputs).
2 Ensure that the REV MODE switch is set to CONT (contin-
uous playback).
6
3 Load a tape into both decks. Select the appropriate Dolby
setting for each deck.
4 Press PLAY on Deck 1.
Playback starts at the start of Deck 1’s tape and goes on to
the end.
Reverse playback then continues from the end of Deck 1’s
tape, to the start of the tape.
Playback then starts at the start of Deck 2’s tape and goes
on to the end.
Reverse playback continues from the end of Deck 2’s tape,
to the start of the tape.
This sequence is repeated.
5 Press STOP (either Deck 1 or Deck 2) to stop the continu-
ous playback.
Page 3
‰ 322 Quick Start guide
Recording on both decks at the same time
Another useful feature of the 322 is ability of both decks to record at the same time
from a single source or sequential recording from a single source. The instructions
below tell you how to record the same program on two tapes at the same time.
1
5
3
8
Connect the source to the DECK 1 INPUT connectors.
1
Insert the tapes into the decks.
Make the appropriate Dolby settings.
6
2 Press the RESET buttons to record the “zero” start time.
3 Select recording on either one side (Ä) or both (ä)
side of the tapes, using the
2
4
8
7
REV MODE switch.
4 Set the INPUT/OUTPUT switch to COMMON.
5 Press the DUAL REC button to light the indicator.
6 Adjust the recording levels and balance on both decks.
7 Press PLAY on either deck.
8 Stop recording with the STOP key of either deck.
Page 4
‰ 322 Quick Start guide
Dubbing using two 322 units
This example shows how to “cascade” two 322 units and produce copies from the
master 322 in the chain.
MASTER
SLAVE
1
2
4
3
Connect the 322 units as shown. The master unit in this
1
picture is on top, and the master’s
should be connected to the slave’s
CASCADE OUTPUTs
DECK 1 INPUTs.
6
5
2 Connect the EXT CONTROL OUT of each machine to the
EXT CONTROL IN of the other.
3 Set the OFF/SLV/MSTR switch of the master to MSTR,
and the
Insert the master tape into Deck 1 of the master and the
slave tapes into Deck 2 of the master, and Decks 1 and 2 of
the slave.
Locate the tapes to the appropriate positions.
OFF/SLV/MSTR of the slave to SLV.
4 The Ó indicator should not be blinking on any deck. If it
is blinking on the master Deck 1, press
Deck 1. If it is blinking on any of the slave decks (including Deck 2 of the master, press
Select high-speed or normal speed dubbing with the master
DUB STDBY NORM or HIGH SPEED buttons.
unit’s
Á on the master’s Deck 2.
Á on the master’s
5 Press PLAY on Deck 2 of the master unit. Playback starts
on the master’s Deck 1 and recording starts on all other
decks.
6 Press the master Deck 2 STOP to stop the dubbing.
TEAC CORPORATION
Phone: (0422) 52-50823-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan
Loading...