Symmons 9601-PLR Installation Manual

	Origins™
9600-PLR, 9601-PLR, 9602-PLR
Operation & Maintenance Manual
Model Numbers			Specification
 9600-PLR			9600-PLR/9601-PLR
Origins Shower Valve			Shower system powered by the Temptrol® Pressure
 9601-PLR			Balancing valve. Features adjustable stop screw to limit
			handle turn, 1 mode showerhead with easy to clean
Origins Shower System
 9602-PLR			rubber nozzles and standard 2.5 gpm (9.5 L/min) flow
			restrictor. Components made from metal and nonmetallic
Origins Tub/Shower System
			materials plated in standard polished chrome finish.
Modifications			9602-PLR
 -1.5	1.5 gpm (5.7 L/min) flow restrictor		Tub/shower system powered by the Temptrol® Pressure
			Balancing valve. Features adjustable stop screw to limit
 -2.0	2.0 gpm (7.6 L/min) flow restrictor		handle turn, diverter tub spout, 1 mode showerhead with
 -231	Super showerhead in place of Clear-Flo		easy to clean rubber nozzles and standard 2.5 gpm
			(9.5 L/min) flow restrictor. Components made from metal
 -295	Institutional showerhead in place of		and nonmetallic materials plated in standard polished
	Clear-Flo		chrome finish.
 -SS	Slip spout on any tub/shower unit
 -X	Integral service stops
 -CHKS	Integral check stops
			Compliance
 -IPS	1/2” female IPS connections
 -REV	Reverse coring for back to back		-ASME A112.18.1/CSA B125.1
	installations		-WaterSense 1.5 gpm (5.7 L/min)
 -LP	Loop handle
			2.0 gpm (7.6 L/min)	Certi ed by
 -B	Chrome brass escutcheon
				CSA Group
 -D	Chrome brass dome cover		For California Residents
			WARNING: This product contains chemicals known to
 -VP	Vandal proof escutcheon screws		the State of California to cause cancer, birth defects, or
 -OP	13” oval plate		other reproductive harm.
 -L/HD	Less showerhead		Warranty
 -TRM	Trim only, valve not included
			Limited Lifetime - to the original end purchaser in
 -STN	Satin Nickel finish
			consumer/residential installations.
			5 Years - for industrial/commercial installations.
			Refer to www.symmons.com/warranty for complete
			warranty information.

Note: Append appropriate -suffix to model number.

Dimensions

A J

K

B
C		L
	E	M
D
F

H	G
	N
II	FLOOR

Notes:

1)All dimensions measured from nominal rough-in (see F as reference).

2)Dimensions subject to change without notice.

		Measurements
	A	6 3/8”, 162 mm
	B	3 1/2”, 89 mm
	C	3 5/8”, 92 mm
		Shower Valve Hole Size
	D	Min. Ø 3”, 76 mm
		Max. Ø 4”, 102 mm
	E	Ref. 77”, 1956 mm
	F	Rough-in
		2 3/8” ± 1/2”, 60 mm ± 13 mm
		Ref. 32”, 813 mm
	G	(9602-PLR)
		Ref. 42”, 1067 mm
		(9601-PLR, 9600-PLR)
	H	Male 1/2” NPT fitting must
		protrude 4” from
		finished wall
	I	5 1/4”, 133 mm
	J	Ø 2 1/2”, 64 mm
	K	Ø 2 3/4”, 70 mm
	L	Ø 5 3/4”, 146 mm
	M	3 3/8”, 86 mm
	N	Ø 2 1/2”, 64 mm

2

Parts Breakdown
	C		Replacement Parts
		Item	Description	Part Number
B		A	Showerhead	4-141*
		B	Shower Arm &	300S*
		C	Flange
A		D	Handle
G				RTS-063*
		H	Assembly
F		E	Dome Cover	T-19*
E		F	Shower
D				9600-PLR-ESC*
		G	Escutcheon Kit
	HOT
F	Water Supply
		I	Tub Spout	054*
		COLD
I		Water Supply
		*Note: Append -STN to part number for Satin Nickel
			finish.
H			Tools Required
		Adjustable wrench

	Notes:		Allen wrench (1/8”)
	1)	Apply a bead of silicone around the perimeter of all shower
		trim installed flush to the finished wall. Leave opening on
		bottom of escutcheon for weep hole.	Phillips head
	2)	Apply plumber tape to all threaded connections.	screwdriver
	3) Escutcheon artwork is dependent on handle style.
			Plumber tape
			Silicone

3

Installation

Note:

For valve body installation, please see valve body manual.

1)Install shower escutcheon (G) to shower valve. Secure with two screws (F).

G

F

2

2)Install dome cover (E) to valve by turning clockwise.

E

1

2

3)Install handle (D) to valve and secure with set screw (H).

D

1

H

Note:

Handle should be facing the 6 o’clock position.

4)Install tub spout (I) to pipe fitting. Turn clockwise to secure.

I	1
	2

5)Attach shower arm (B) and flange (C) to vertical shower pipe. Turn clockwise to tighten.

	1
	2
B	C

6)Install showerhead (A) to shower arm (B). Turn clockwise to tighten.

B

1

A

4

Operation (Temperature Control)

1)Turn shower handle counterclockwise approximately 1/4 turn to put valve in cold position.

2)Turn shower handle counterclockwise approximately 1/2 turn to put valve in warm position.

3)Turn shower handle counterclockwise approximately 3/4 turn to put valve in hot position.

Operation (Diverter Control)

1) Diverter lever in down position for tub spout operation.					2) Diverter lever in up position for shower operation.

Troubleshooting Chart

	Problem	Cause	Solution
			Clean finished trim area with a soft
	Finish is spotting.	Elements in water supply may cause	cloth using mild soap and water or a
		water staining on finish.	non-abrasive cleaner and then quickly
			rinse with water.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: [phone] ■ Fax: [phone] Copyright © 2015 Symmons Industries, Inc. ■ www.symmons.com ■ [e-mail] ■ ZV-3126 REV A ■ 110515