STIHL FS 130 Owner's Manual

STIHL FS 130
STIH)
Instruction Manual Manual de instrucciones
Warning!
Read and follow all safety precautions in Instruction Manual – improper use can cause serious or fatal injury.
Advertencia!
Lea y siga todas las precauciones de seguridad dadas en el manual de instrucciones – el uso incorrecto puede causar lesiones graves o mortales.
Contents
English / USA
Guide to Using this Manual .............. 2
Safety Precautions and Working
Techniques ....................................... 3
Approved Combinations of Cutting Tool, Deflector,
Handle and Harness ....................... 20
Approved Power Tool
BA_SE_159_004_01_06.fmPrinted on chlorine-free paper.
Attachments .................................... 22
Mounting the Bike Handle .............. 22
Mounting the Loop Handle ............. 24
Adjusting the Throttle Cable ........... 26
Fitting the Carrying Eye .................. 26
Mounting the Deflector ................... 27
Mounting the Cutting Tools ............. 28
4-MIX Engine .................................. 32
Fuel ................................................ 32
Fueling ............................................ 33
Fitting the Harness ......................... 34
Balancing the Brushcutter .............. 35
Starting / Stopping the Engine ........ 36
Operating Instructions .................... 39
Cleaning the Air Filter ..................... 39
Motor Management ........................ 40
Adjusting the Carburetor ................ 40
Spark Arresting Screen in
Muffler ............................................. 42
Printing inks contain vegetable oils; paper can be recycled.
Checking the Spark Plug ................ 42
Lubricating the Gearbox ................. 43
Replacing Starter Rope
and Rewind Spring ......................... 44
Storing the Machine ........................ 47
Sharpening Metal Cutting Tools ...... 47
Inspections and Maintenance
by Dealer ........................................ 48
Maintenance Chart ......................... 49
Parts and Controls .......................... 51
Specifications ................................. 54
Special Accessories ....................... 54
Maintenance and Repairs .............. 55
STIHL Incorporated Federal Emission Control Warranty
Statement ....................................... 56
STIHL Incorporated California Exhaust and Evaporative Emissions Control Warranty’
Statement ....................................... 58
Trademarks .................................... 60
Allow only persons who understand this manual to operate your trimmer/ brushcutter.
To receive maximum performance and satisfaction from your STIHL trimmer/ brushcutter, it is important that you read and understand the maintenance and safety precautions, starting on page 3, before using your trimmer/brushcutter.
Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in this manual.
!Warning!
Because a trimmer/brushcutter is a high­speed cutting tool some special safety precautions must be observed to reduce the risk of personal injury. Careless or improper use may cause serious or even fatal injury. Make sure your unit is equipped with the proper deflector, handle and harness for the type of cutting attachment being used. Always wear proper eye protection. STIHL's philosophy is to continually improve all of its products. As a result, engineering changes and improve­ments are made from time to time. If the operating characteristics or the appear­ance of your trimmer/brushcutter differs from those described in this manual, please contact your STIHL dealer for information and assistance.
STIHl
© ANDREAS STIHL AG & Co. KG, 2007
0458 258 8621 B. M3. L7. CP. Printed in USA
1FS 130, FS 130 R
English / USA
Guide to Using this Manual
Pictograms
All the pictograms attached to the machine are shown and explained in this manual.
The operating and handling instructions are supported by illustrations.
Symbols in text
The individual steps or procedures described in the manual may be marked in different ways:
: A bullet marks a step or procedure
without direct reference to an illustration.
A description of a step or procedure that refers directly to an illustration may contain item numbers that appear in the illustration. Example:
Loosen the screw (1)
Lever (2) ...
In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the symbols described below:
Warning where there is a risk of an accident or personal injury or serious damage to property.
Caution where there is a risk of damaging the machine or its individual components.
Note or hint which is not essential for using the machine, but may improve the operator’s under­standing of the situation and result in better use of the machine.
Note or hint on correct procedure in order to avoid damage to the environment.
Equipment and features
This instruction manual may refer to several models with different features. Components that are not installed on all models and related applications are marked with an asterisk (*). Such components may be available as special accessories from your STIHL dealer.
Engineering improvements
STIHL’s philosophy is to continually improve all of its products. As a result, engineering changes and improvements are made from time to time. If the operating characteristics or the appearance of your machine differ from those described in this manual, please contact your STIHL dealer for assistance.
Therefore some changes, modifications and improvements may not be covered in this manual.
2
FS 130, FS 130 R
English / USA
Safety Precautions and Working Techniques
Because a trimmer/ brushcutter is a high­speed, fast-cutting power tool sometimes equipped with sharp cutting blades,
special safety precautions must be observed to reduce the risk of personal injury.
It is important that you
read, fully understand and
observe the following
safety precautions and
warnings. Read the
instruction manual and the safety precautions periodically. Careless or improper use may cause serious or fatal injury.
The terminology utilized in this manual when referring to the power tool reflects the fact that different types of cutting attachments may be mounted on it. The term "trimmer" is used to designate an FS unit that is equipped with a nylon line head or a head with flexible plastic blades (i.e., the PolyCut head). A "brushcutter" designates a unit equipped with a rigid metal blade. Many FS models may be used as either a trimmer or a brushcutter - therefore, the power tool is referred in this manual as a "trimmer/brushcutter." Some smaller and/or lightweight FS models may only be used as a trimmer, i.e., they may not be used with metal blades.
The term "clearing saw" indicates a high-powered trimmer/brushcutter that is particularly suited for use with a circular saw blade to clear saplings or small trees. FS models with an "R" on the nameplate were originally configured (at the time of distribution) as a trimmer with a loop handle.
!Warning
As more fully explained later in these Safety Precautions, to reduce the risk of personal injury, make sure your unit is equipped with the proper handle, harness and deflector for the type of cutting attachment you are using. Use only cutting attachments that are specifically authorized by STIHL for use on your FS model.
Have your STIHL dealer show you how to operate your power tool. Observe all applicable local safety regulations, standards and ordinances.
!Warning!
Do not lend or rent your power tool without the instruction manual. Be sure that anyone using it understands the information contained in this manual.
!Warning!
The use of this machine may be hazardous. If the rotating line or blade comes in contact with your body, it will cut you. When it comes in contact with solid foreign objects such as rocks or bits of metal, it may fling them directly or by ricochet in the direction of bystanders or the operator. Striking such objects could damage the cutting attachment and may cause blades to crack, chip or break. Thrown objects, including broken heads or blades, may result in serious or fatal injury to the operator or bystanders. STIHL does not recommend the use of rigid blades when cutting in stony areas.
Use your trimmer/brushcutter equipped with the appropriate cutting attachment only for cutting grass, brush, wood and similar material. It must not be used for any other purposes, since such misuse may result in an accident or damage to the machine.
!Warning!
Minors should never be allowed to use this power tool. Bystanders, especially children, and animals should not be allowed in the area where it is in use.
3FS 130, FS 130 R
English / USA
!Warning!
To reduce the risk of injury to bystanders and damage to property, never let your power tool run unattended. When it is not in use (e.g. during a work break), shut it off and make sure that unauthorized persons do not use it.
Most of these safety precautions and warnings apply to the use of all STIHL trimmer/brushcutters. Different models may have different parts and controls. See the appropriate section of your instruction manual for a description of the controls and the function of the parts of your model.
Safe use of a trimmer/brushcutter involves
1. the operator
2. the power tool
3. the use of the power tool.
THE OPERATOR
Physical Condition
You must be in good physical condition and mental health and not under the influence of any substance (drugs, alcohol, etc.) which might impair vision, dexterity or judgment. Do not operate this machine when you are fatigued.
!Warning!
Be alert – if you get tired, take a break. Tiredness may result in loss of control. Working with any power tool can be strenuous. If you have any condition that might be aggravated by strenuous work, check with your doctor before operating this machine.
!Warning!
Prolonged use of a power tool (or other machines) exposing the operator to vibrations may produce whitefinger disease (Raynaud's phenomenon) or carpal tunnel syndrome.
These conditions reduce the hand's ability to feel and regulate temperature, produce numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis.
All factors which contribute to white­finger disease are not known, but cold weather, smoking and diseases or physical conditions that affect blood vessels and blood transport, as well as high vibration levels and long periods of exposure to vibration are mentioned as factors in the development of whitefinger disease. In order to reduce the risk of whitefinger disease and carpal tunnel syndrome, please note the following:
Most STIHL power tools are available with an anti-vibration (“AV”) system designed to reduce the transmission of vibrations created by the machine to the operator's hands. An AV system is recommended for those persons using power tools on a regular or sustained basis.
4
FS 130, FS 130 R
English / USA
Keep the AV system well maintained. A power tool with loose components or with damaged or worn AV buffers will tend to have higher vibration levels.
Maintain a firm grip at all times, but do not squeeze the handles with constant, excessive pressure. Wear gloves and keep your hands warm. Take frequent breaks.
All the above-mentioned precautions do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome. Therefore, continual and regular users should closely monitor the condition of their hands and fingers. If any of the above symptoms appear, seek medical advice immediately.
!Warning!
The ignition system of the STIHL unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with a pacemaker should consult their physician and the pacemaker manufacturer before operating this tool.
Proper Clothing
!Warning!
To reduce the risk of injury, the operator should wear proper protective apparel. The deflector provided with your power tool will not protect the operator from all foreign objects (gravel, glass, wire, etc.) thrown back by the rotating cutting attachment. Thrown objects may also ricochet and strike the operator.
!Warning!
To reduce the risk of injury to your eyes never operate your power tool unless wearing goggles or properly fitted protective
glasses with adequate top and side protection complying with ANSI Z 87.1 (or your applicable national standard). To reduce the risk of injury to your face STIHL recommends that you also wear a face shield or face screen over your goggles or protective glasses.
!Warning!
Power tool noise may damage your hearing. Wear sound barriers (ear plugs or ear mufflers) to protect your hearing.
Continual and regular users should have their hearing checked regularly.
Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings (shouts, alarms, etc.) is restricted.
Always wear gloves when
handling the machine and
metal blades. Heavy-duty,
nonslip gloves improve
your grip and help to
protect your hands.
Clothing must be sturdy
and snug-fitting, but allow
complete freedom of
movement. Wear long
pants made of heavy
material to help protect
your legs. Do not wear
shorts, sandals or go
barefoot.
5FS 130, FS 130 R
English / USA
389BA019 KN
Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, unconfined long hair or anything that could
become caught on branches, brush or the moving parts of the unit. Secure hair so it is above shoulder level.
Good footing is very
important. Wear sturdy
boots with nonslip soles.
Steel-toed safety boots
are recommended.
Wear an approved safety
hard hat to reduce the risk
of injury to your head
when there is a danger of
head injuries.
THE POWER TOOL
For illustrations and definitions of the power tool parts see the chapter on “Main Parts and Controls.”
!Warning!
Never modify this power tool in any way. Only attachments supplied by STIHL and expressly approved by STIHL for use with the specific STIHL model are authorized. Although certain unauthorized attachments are useable with STIHL power tools, their use may, in fact, be extremely dangerous. For the cutting attachments authorized by STIHL for your unit, see the chapter “Approved Combinations of Cutting Attachment, Deflector, Handle and Harness“ in the instruction manual or the STIHL “Power Tools and Accessories“ catalog.
If this tool is subjected to unusually high loads for which it was not designed (e.g. heavy impact or a fall), always check that it is in good condition before continuing work. Check in particular that the fuel system is tight (no leaks) and that the controls and safety devices are working properly. Do not continue operating this machine if it is damaged. In case of doubt, have it checked by your STIHL servicing dealer.
THE USE OF THE POWER TOOL
Transporting the Power Tool
!Warning!
To reduce the risk of injury from loss of control and blade or line contact, never carry or transport your power tool with the cutting attachment moving.
It may be carried only in a horizontal position. Grip the shaft in a manner that the machine is balanced horizontally. Keep the hot muffler away from your body and the cutting attachment behind you.
6
FS 130, FS 130 R
English / USA
!Warning!
Always shut off the engine and make sure the cutting attachment has stopped before putting a trimmer/brushcutter down. When transporting it in a vehicle, properly secure it to prevent turnover, fuel spillage and damage to the unit. STIHL recommends that you keep metal blades covered with the transport guard (optional accessory).
Fuel
Your STIHL power tool uses an oil­gasoline mixture for fuel (see the chap­ter on “Fuel” of your instruction manual).
!Warning!
Gasoline is an extremely
flammable fuel. If spilled
and ignited by a spark or
other ignition source, it
can cause fire and serious
burn injury or property damage. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape from the fuel system.
Fueling Instructions
!Warning!
Fuel your power tool in well-ventilated areas, outdoors. Always shut off the engine and allow it to cool before refueling. Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used, the weather conditions and the tank venting system.
In order to reduce the risk of burns and other personal injury from escaping gas vapor, remove the fuel filler cap on your power tool carefully so as to allow any pressure build-up in the tank to release slowly. Never remove the fuel filler cap while the engine is running.
Select bare ground for fueling and move at least 10 feet (3 m) from the fueling spot before starting the engine. Wipe off any spilled fuel before starting your machine.
!Warning!
Check for fuel leakage while refueling and during operation. If fuel leakage is found, do not start or run the engine until the leak is fixed and any spilled fuel has been wiped away. Take care not to get fuel on your clothing. If this happens, change your clothing immediately.
Different models may be equipped with different fuel caps.
Cap with grip
!Warning!
In order to reduce the risk of fuel spillage and fire from an improperly tightened fuel cap, correctly position and tighten the fuel cap in the fuel tank opening.
To do this with this STIHL cap, raise the grip on the top of the cap until it is upright at a 90° angle. Insert the cap in the fuel
tank opening with the triangular marks on the grip of the cap and on the fuel tank opening lining up. Using the grip, turn the cap firmly clockwise as far as it will go (approx. a quarter turn).
Fold the grip flush with the
top of the cap. If the grip
does not lie completely
flush with the cap and the
detent on the grip does
not fit in the corresponding recess in the filler neck, the cap is not properly seated and tightened and you must repeat the above steps.
7FS 130, FS 130 R
English / USA
Screw cap
!Warning!
Unit vibrations can cause an improperly tightened fuel filler cap to loosen or come off and spill quantities of fuel. In order
to reduce the risk of fuel spillage and fire, tighten the fuel filler cap by hand as securely as possible.
Before Starting
!Warning!
Always check your power tool for proper condition and operation before starting, particularly the throttle trigger, throttle trigger interlock, stop switch, cutting attachment, deflector and harness. The throttle trigger must move freely and always spring back to the idle position. Never attempt to modify the controls or safety devices. Never use a power tool that is damaged or not properly maintained.
!Warning!
The cutting attachment must be properly tightened and in safe operating condition. Inspect for loose parts (nuts, screws, etc.) and for cracked or damaged heads or cracked, bent, warped or damaged blades. Replace damaged heads or blades before using the power tool. Always keep blades sharp.
Keep the handles clean and dry at all times; it is particularly important to keep them free of moisture, pitch, oil, grease or resin in order for you to maintain a firm grip and properly control your power tool.
!Warning!
Check that the spark plug boot is securely mounted on the spark plug – a loose boot may cause arcing that could ignite combustible fumes and cause a fire.
! Warning!
To reduce the risk of personal injury to the operator from blade or line
contact and thrown objects, make sure your unit is equipped with the proper deflector, handle and harness for the type of cutting attachment being used (see chart in the chapter on "Approved Combinations of Cutting Attachment, Deflector, Handle and Harness").
As can be seen in that chart, some cutting attachments may require you to change your deflector, handle and/or harness.
Keep the deflector (and the attached skirt where appropriate) adjusted properly at all times (see chapters on "Mounting the Deflector" and "Mounting the Cutting Attachments" of your instruction manual).
!Warning!
Do not attach any cutting attachment to a unit without proper installation of all required parts. Failure to use the proper parts may cause the blade or head to fly off and seriously injure the operator or bystanders.
8
FS 130, FS 130 R
English / USA
A
000BA006 KN
B
000BA007 KN
.
Arrows on the deflector (A) and limit stop (B) (as seen from the underside) show the correct direction of rotation of the cutting attachment. When viewed from above, however, the cutting attachment rotates counterclockwise.
Adjust carrying harness and hand grip to suit your size before starting work. The machine should be properly balanced as specified in your instruction manual for proper control and less fatigue in operation. To be better prepared in case of an emergency, practice releasing the unit from the harness as quickly as possible.
Starting
Start the engine at least 10 feet (3 meters) from the fueling spot, outdoors only.
For specific starting instructions, see the appropriate section of your manual. Place the power tool on firm ground or other solid surface in an open area. Maintain good balance and secure footing.
!Warning!
To reduce the risk of injury from blade or line contact, be absolutely sure that the cutting attachment is clear of you and all other obstructions and objects, including the ground, because when the engine starts at starting-throttle, engine speed will be fast enough for the clutch to engage and move the cutting attachment.
Once the engine has started, immediately blip the throttle trigger, which should release the starting throttle and allow the engine to slow down to idle.
With the engine running only at idle, attach the power tool to the spring hook of your harness (see appropriate chapter of this manual).
!Warning!
Your power tool is a one-person machine. Do not allow other persons in the general work area, even when starting.
!Warning!
To reduce the risk of injury from loss of control, do not attempt to “drop start” your power tool.
!Warning!
When you pull the starter grip, do not wrap the starter rope around your hand. Do not let the grip snap back, but guide the starter rope to rewind it properly. Failure to follow this procedure may result in injury to your hand or fingers and may damage the starter mechanism.
Important Adjustments
!Warning!
To reduce the risk of personal injury from loss of control or contact with the running cutting attachment, do not use your unit with incorrect idle adjustment. At correct idle speed, the cutting attachment should not move. For directions on how to adjust idle speed, see the appropriate section of your instruction manual.
If you cannot set the correct idle speed, have your STIHL dealer check your power tool and make proper adjustments and repairs.
9FS 130, FS 130 R
English / USA
002BA055 KN
002BA054 KN
During Operation
Holding and controlling the power tool
Always hold the unit firmly with both hands on the handles while you are working. Wrap your fingers and thumbs around the handles.
!Warning!
Never attempt to operate your power tool with one hand. Loss of control of the power tool resulting in serious or fatal injury may
result. To reduce the risk of cut injuries, keep hands and feet away from the cutting attachment. Never touch a moving cutting attachment with your hand or any other part of your body.
!Warning!
Do not overreach. Keep proper footing and balance at all times. Special care must be taken in slippery conditions (wet ground, snow) and in difficult, overgrown terrain. Watch for hidden obstacles such as tree stumps, roots and ditches to avoid stumbling. For better footing, clear away scrub and cuttings. Be extremely cautious when working on slopes or uneven ground.
!Warning
To reduce the risk of injury from loss of control, never work on a ladder or on any other insecure support. Never hold the cutting attachment above waist height.
Working conditions
Operate and start your power tool only outdoors in a well ventilated area. Operate it under good visibility and daylight conditions only. Work carefully.
!Warning!
As soon as the engine is running, this product generates toxic exhaust fumes containing chemicals such as
unburned hydrocarbons (including benzene) and carbon monoxide that are known to cause respiratory problems, cancer, birth defects, or other reproductive harm. Some of the gases (e.g. carbon monoxide) may be colorless and odorless. To reduce the risk of serious or fatal injury/illness from inhaling toxic fumes, never run the machine indoors or in poorly ventilated locations.
!Warning!
If the vegetation being cut or the surrounding ground is coated with a chemical substance (such as an active pesticide or herbicide), read and follow the instructions and warnings that accompanied the substance at issue.
10
FS 130, FS 130 R
English / USA
15m (50ft)
!Warning!
Inhalation of certain dusts, especially organic dusts such as mold or pollen, can cause susceptible persons to have an allergic or asthmatic reaction. Substantial or repeated inhalation of dust and other airborne contaminants, in particular those with a smaller particle size, may cause respiratory or other illnesses. Control dust at the source where possible. Use good work practices, such as operating the unit so that the wind or operating process directs any dust raised by the power tool away from the operator. Follow the recommendations of EPA/OSHA/ NIOSH and occupational and trade associations with respect to dust (“particulate matter”). When the inhalation of dust cannot be substantially controlled, i.e., kept at or near the ambient (background) level, the operator and any bystanders should wear a respirator approved by NIOSH/ MSHA for the type of dust encountered.
Operating instructions
!Warning!
Do not operate your power tool using the starting throttle lock, as you do not have control of the engine speed.
In the event of an emergency, shut off the engine immediately – move the slide control / stop switch to 0 or STOP.
!Warning!
The cutting attachment continues to rotate for a short period after the throttle trigger is released (flywheel effect).
!Warning!
The rotating cutting attachment may fling foreign objects directly or by ricochet a great distance.
To reduce the risk of eye and other injury always wear proper eye protection (see the chapter on “Proper Clothing“) and ensure that bystanders are at least 50 feet (15 m) away. To reduce the risk of damage to property, also maintain this distance from such objects as vehicles or windows. Any coworkers who must be in the restricted area should also wear goggles or protective glasses. Stop the engine immediately if you are approached.
11FS 130, FS 130 R
English / USA
!Warning!
Before you start work, examine the area for stones, glass, fence wire, metal, trash or other solid objects. The cutting attachment could throw objects of this kind.
!Warning!
This trimmer/brushcutter is normally to be used at ground level with the cutting attachment parallel to the ground. Use of a trimmer/brushcutter above ground level or with the cutting attachment perpendicular to the ground may increase the risk of injury, since the cutting attachment is more fully exposed and the power tool may be more difficult to control.
!Warning!
During cutting, check the tightness and the condition of the cutting attachment at regular short intervals with the engine and attachment stopped. If the behavior of the attachment changes during use, stop the engine immediately, wait until the cutting attachment stops, and check the nut securing the attachment for tightness and the blade or head for cracks, wear and damage.
!Warning!
A loose blade or head may vibrate, crack, break or come off the trimmer/ brushcutter, which may result in serious or fatal injury. Make sure that the cutting attachment is properly tightened. Use the wrench supplied or one of sufficient length to obtain the proper torque. If the blade or head loosens after being properly tightened, stop work immediately. The retaining nut may be worn or damaged and should be replaced. If the blade or head continues to loosen, see your STIHL dealer. Never use a trimmer/brushcutter with a loose cutting attachment.
!Warning!
Replace a cracked, damaged or worn­out head or a cracked, bent, warped, damaged, dull or worn out blade immediately, even if damage is limited to superficial cracks. Such attachments may shatter at high speed and cause serious or fatal injury.
!Warning!
When using rigid blades, avoid cutting close to fences, sides of buildings, tree trunks, stones or other such objects that could cause the power tool to kick out or could cause damage to the blade. STIHL recommends use of the nylon line heads for such jobs. In addition, be alert to an increased possibility of ricochets in such situations.
!Warning!
If the head, blade or deflector becomes clogged or stuck, always shut off the engine and make sure the cutting attachment has stopped before cleaning. Grass, weeds, etc. should be cleaned off the blade or from around the head at regular intervals.
!Warning!
To reduce the risk of unintentional rotation of the cutting attachment and injury, always shut off the engine and remove the spark plug boot before replacing the cutting attachment. To reduce the risk of injury, always shut off the engine before adjusting the length of the nylon line on manually adjustable mowing heads.
!Warning
The gearbox becomes hot during operation. To reduce the risk of burn injury, do not touch the gear housing when it is hot.
12
FS 130, FS 130 R
English / USA
!Warning!
The muffler and other parts of the engine (e.g. fins of the cylinder, spark plug) become hot during operation and remain hot for a while after stopping the engine. To reduce risk of burns do not touch the muffler and other parts while they are hot.
!Warning!
To reduce the risk of fire and burn injury, keep the area around the muffler clean. Remove excess lubricant and all debris such as pine needles, branches or leaves. Let the engine cool down sitting on concrete, metal, bare ground or solid wood away from any combustible substances.
!Warning!
Never modify your muffler. The muffler could be damaged and cause an increase in heat radiation or sparks, thereby increasing the risk of fire and burn injury. You may also permanently damage the engine. Have your muffler serviced and repaired by your STIHL servicing dealer only.
Catalytic converter
!Warning!
Some STIHL power tools are equipped with a catalytic converter, which is designed to reduce the exhaust emissions of the
engine by a chemical process in the muffler. Due to this process, the muffler does not cool down as rapidly as conventional mufflers when the engine returns to idle or is shut off. To reduce the risk of fire and burn injuries, the following specific safety precautions must be observed.
!Warning!
Since a muffler with a catalytic converter cools down less rapidly than conven­tional mufflers, always set your power tool down in the upright position and never locate it where the muffler is near dry brush, grass, wood chips or other combustible materials while it is still hot.
!Warning!
An improperly mounted or damaged cylinder housing or a damaged/ deformed muffler shell may interfere with the cooling process of the catalytic converter. To reduce the risk of fire or burn injury, do not continue work with a damaged or improperly mounted cylinder housing or a damaged/ deformed muffler shell.
Your catalytic converter is furnished with screens designed to reduce the risk of fire from the emission of hot particles. Due to the heat from the catalytic reaction, these screens will normally stay clean and need no service or maintenance. If you experience loss of performance and you suspect a clogged screen, have your muffler maintained by a STIHL servicing dealer.
13FS 130, FS 130 R
English / USA
000BA015 KN
USING THE CUTTING ATTACHMENTS
For an illustration of the various cutting attachments and instructions on proper mounting see the chapter on "Mounting the Cutting Attachments" in your instruction manual.
!Warning!
To reduce the risk of severe or fatal injury from blade contact and/or loss of control, never attempt to use a metal blade on an FS model for which it is not authorized.
Using the Mowing Heads
Do not use with mowing line longer than the intended length. With a properly mounted deflector, the built-in line­limiting blade will automatically adjust the line to its proper length.
Using the unit with an overly long nylon cutting line increases the load on the engine and reduces its operating speed. This causes the clutch to slip continuously and results in overheating and damage to important components (e.g. clutch, polymer housing components). Such damage could, among other things, cause the cutting attachment to rotate at idle.
Mowing heads are to be used only on trimmer/brushcutters equipped with a line-limiting blade in the deflector in order to keep the line at the proper length (see "Parts and Controls" chapter in your instruction manual).
If the lawn edges are planted with trees or bordered by a fence etc., it is best to use a nylon line head. It achieves a "softer" cut with less risk of damaging tree bark etc. than polymer blades.
However, the polymer-bladed STIHL PolyCut produces a better cut if there are no plants along the edge of the lawn. Sharpening is not necessary, and worn polymer blades are easily replaced.
!Warning!
To reduce the risk of serious injury, never use wire or metal-reinforced line or other material in place of the nylon cutting lines. Pieces of wire could break off and be thrown at high speed toward the operator or bystanders.
STIHL SuperCut mowing head
Fresh line is advanced automatically. Frayed line is replaced by a simple adjustment (see instruction sheet supplied with mowing head).
STIHL TrimCut mowing head
Frayed line is replaced by a simple adjustment (see instruction sheet supplied with mowing head).
STIHL AUTOCUT mowing head
Nylon cutting cord advances automatically when tapped against the ground (TapAction).
14
FS 130, FS 130 R
English / USA
002BA177 KN
002BA135 KN
STIHL PolyCut mowing head
Uses either nylon lines or nonrigid, pivoting polymer blades.
!Warning!
Three rectangular wear limit marks are applied to the base (periphery) of the PolyCut. To reduce the risk of serious injury from breakage of the head or blades, the PolyCut must not be used when it has worn as far as one of these marks. It is important to follow the maintenance instructions supplied with the head.
STIHL FixCut mowing head
Uses pre-cut lengths of nylon line.
Observe wear indicators.
Do not continue using the mowing head if the raised moldings (1) on the base are missing or worn – see right illustration above. The mowing head may otherwise shatter and flying objects could result in injury to the operator or bystanders. Install a new mowing head.
Risk of Kickout (Blade Thrust) with All Rigid Cutting Blades
!Warning!
Kickout (blade thrust) is the sudden and uncontrolled motion towards the operator's right or rear that can occur when the shaded area (especially the darkly shaded area) of a rotating blade comes in contact with a solid rigid object like a tree, rock, bush or wall. The rapid counterclockwise rotation of the blade may be stopped or slowed, and the cutting attachment may be thrown to the right or to the rear.
This kickout (blade thrust) may cause loss of control of the power tool and may result in serious or fatal injury to the operator or bystanders. To reduce the risk of injury, extreme caution should be used when cutting with the shaded area of any rigid blade.
15FS 130, FS 130 R
English / USA
000BA020 KN
002BA066 KN
Using the Grass Cutting Blade
All kinds of grass and weeds can be easily cut with the grass cutting blade. The power tool is swept in an arc similar to a scythe.
!Warning!
To reduce the risk of serious or fatal injury from blade breakage, never attempt to use this blade to cut woody materials.
The 4-tooth grass cutting blade is intended to cut grass and weeds. It has 4 cutting knives with cutting edges on both sides, i.e. front and rear. When the cutting edges on one side become dull, the blade can be turned over to utilize the cutting edges on the other side.
The 8-tooth grass cutting blade is recommended for cutting fern or reed.
Both types of grass cutting blade have to be resharpened when all cutting edges are dull.
Using the Brush Knife
When fitted to the power tool, the brush knife is suitable for applications ranging from cutting matted grass to clearing weeds, wild growth and scrub.
To cut wild growth and scrub, lower the rotating brush knife down onto the growth to achieve a chopping effect – but keep the tool below waist height at all times.
!Warning!
Exercise extreme caution when using this method of cutting. The higher the cutting attachment is off the ground, the greater the risk of loss of control and of cuttings being thrown sideways.
Use the power tool like a scythe to cut grass, i.e. sweep it to and fro in an arc.
!Warning!
When cutting woody materials, use the left side of the blade to avoid "kickout" (blade thrust) situations.
!Warning!
Improper use of a brush knife may cause it to crack, chip or shatter. Thrown blade fragments may seriously or fatally injure the operator or bystanders. To reduce the risk of injury, avoid contact with hard or solid foreign objects such as stones, rocks or pieces of metal.
!Warning!
When cutting young saplings or other woody materials up to 2 cm (3/4") in diameter, use the left side of the blade to avoid "kickout" situations (see section on “Risk of kickout (blade thrust) with all rigid cutting blades”). Do not attempt to cut woody material with a larger diameter, since the blade may catch or jerk the power tool forward. This may cause damage to the blade or power tool or loss of control of the power tool, resulting in personal injury. Use a circular saw blade for such work.
!Warning!
Inspect the brush knife at regular short intervals for signs of damage. Do not continue working with a damaged brush knife. Resharpen the brush knife regularly (when it has dulled noticeably).
16
FS 130, FS 130 R
English / USA
000BA016 KN
002BA214 ST
002BA068 KN
Using the Circular Saw Blade
Circular saw blades are suitable for thinning brush and cutting small trees up to a diameter of 4 cm (1 1/2”). Do not attempt to cut trees with larger diameters, since the blade may catch or jerk the trimmer/brushcutter forward. This may cause damage to the blade or loss of control of the power tool and result in serious injury. Use a chain saw for such work.
!Warning!
To reduce the risk that the blade will crack and/or break, avoid all contact with stones, rocks or the ground. Sharpen blades in a timely manner as specified – dull teeth may cause the blade to crack or shatter.
When a trimmer/brushcutter with a circular saw blade is used to cut down small trees, STIHL recommends that the standard deflector be removed and replaced by the special limit stop deflector (see chapter on “Mounting the Deflector”). This limit stop helps to keep the unit positioned against the tree during the cutting process. Inexperienced users should place the left side of the stop against the tree trunk before beginning to cut. This will keep the trimmer/brushcutter against the tree during the cutting operation and will reduce the risk of loss of control and possible kickout (described above and briefly again below).
Before starting the cut, accelerate the engine up to full throttle. Perform cut with uniform pressure. STIHL recommends that the circular saw blade be applied to the right of the tree, using the non-shaded area of the blade, as shown in the illustration above.
17FS 130, FS 130 R
English / USA
!Warning!
The risk of kickout is highest when cutting in the darker shaded area. To reduce the risk of kickout and resulting injury, do not use this area of the circular saw blade for cutting trees or shrubs. Special techniques using the lighter shaded areas of the blade to cut shrubs and trees should only be used by experienced operators with specialized training in the use and control of the trimmer/brushcutter.
!Warning!
To reduce the risk of loss of control and serious injury to the operator or bystanders by a kickout, never use a circular saw blade on a trimmer/ brushcutter with a loop handle, but rather only on one with a bicycle handle.
When felling small trees, maintain a distance of at least two tree lengths from the nearest coworker.
!Warning!
In order to reduce the risk of injury from thrown objects or operator contact with the blade or head, be sure to remount the standard deflector when no longer using a circular saw blade.
MAINTENANCE, REPAIR AND STORING
Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, if you make a warranty claim for a component which has not been serviced or maintained properly or if nonapproved replacement parts were used, STIHL may deny coverage.
!Warning!
Use only identical STIHL replacement parts for maintenance and repair. Use of non-STIHL parts may cause serious or fatal injury.
Strictly follow the maintenance and repair instructions in the appropriate sections of your instruction manual.
!Warning!
Always stop the engine and make sure that the cutting attachment is stopped before doing any maintenance or repair work or cleaning the power tool. Do not attempt any maintenance or repair work not described in your instruction manual. Have such work performed by your STIHL servicing dealer only.
Wear gloves when handling or performing maintenance on blades.
!Warning!
Use the specified spark plug, and make sure it and the ignition lead are always clean and in good condition. Always press spark plug boot snugly onto spark plug terminal of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be securely attached.) A loose connection between the spark plug and the ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire.
!Warning!
Never test the ignition system with the spark plug boot removed from the spark plug or with a removed spark plug, since uncontained sparking may cause a fire.
!Warning!
Do not operate your power tool if the muffler is damaged, missing or modified. An improperly maintained muffler will increase the risk of fire and hearing loss. If your muffler was equipped with a spark-arresting screen to reduce the risk of fire, never operate your power tool if the screen is missing or damaged. Remember that the risk of forest fires is greater in hot or dry weather.
18
FS 130, FS 130 R
!Warning!
Never repair damaged cutting attach­ments by welding, straightening or modifying the shape. This may cause parts of the cutting attachment to come off and result in serious or fatal injuries.
Keep blades sharp. Tighten all nuts, bolts and screws, except the carburetor adjustment screws, after each use.
Store the power tool in a dry and high or locked location out of reach of children.
Before storing for longer than a few days, always empty the fuel tank. See chapter "Storing the Machine" in the instruction manual.
English / USA
19FS 130, FS 130 R
English / USA
Approved Combinations of Cutting Tool, Deflector, Handle and Harness
Cutting Tools
1 STIHL SuperCut 20-2
2 STIHL AutoCut 25-2
3 STIHL AutoCut 30-2
4 STIHL TrimCut 30-2
5 STIHL PolyCut 20-3
6 STIHL FixCut 25-2
7 Grass cutting blade 230-4
8 Grass cutting blade230-8
9 Brush knife 250
10 Scratcher tooth
circular saw blade 200
11 Chisel tooth
circular saw blade 200
Grass cutting blades, brush knifes and circular saw blades made of any other non-metal material are not permitted.
Deflectors
12 Deflector for mowing heads only
13 Deflector with 14 Skirt and blade for all mowing heads
(see ’Mounting the Deflector’)
15 Deflector without skirt and blade
for all metal mowing tools and brush knife
16 Limit stop for circular saw blades
Handles
17 Loop handle
18 Loop handle with 19 Barrier bar
20 Bike handle
Harnesses
21 Shoulder strap may be used
22 Shoulder strap must be used
23 Full harnesss may be used
24 Full harnesss must be used
Equipment
Among other parts, the complete unit includes:
Cutting tool
Deflector
Handle
Harness (bike handle unit only)
Select the correct combination from the table according to the cutting tool you intend to use. Read the table horizontally from left to right. Other combinations, e.g. reading the table diagonally, are not permitted.
!!!! Warning!
To reduce the risk of injury from thrown objects and blade contact, never operate your unit without the proper deflector for the cutting attachment being used. To reduce the risk of injury from loss of control and / or contact with the cutting tool, make sure your unit is equipped with a proper handle and harness for the type of cutting attachment being used.
!!!! Warning!
STIHL brushcutters with a loop handle without barrier bar may be used only with the above mentioned mowing head with nylon line or plastic blades. Other plastic or metal cutting tools, but not circular saw blades, may be used only on brushcutters with a bike handle or loop handle with barrier bar in order to reduce the risk of personal injury through contact with the cutting tool.To reduce the risk of serious injury to the operator or bystanders by kickout, never use a circular saw blade on a brushcutter with a loop handle. Circular saw blades may be used only on brushcutters with a bike handle.
20
FS 130, FS 130 R
Cutting tool Deflector Handle Harness / Shoulder Strap
681FK111 KN
681FK003
681FK006
681FK011
5
3
1
4
6
681FK006
2
681FK023
12
681BA002 KN
13
14
17
002BA002 K
002BA003 K
18
19
002BA125 KN
21
002BA001 K
20
002BA005 K
22
681FK014
8
9
7
681FK021
15
002BA003 K
18
19
002BA001 K
20
002BA127 KN
002BA126 KN
23
002BA005 K
22
23
681FK016
11
10
681FK024
16
002BA001 K
20
002BA026 KN
002BA006 K
24
24
English / USA
21FS 130, FS 130 R
English / USA
Approved Power Tool Attachments
228BA037 KN
BF
FH
FCS
KB
KW
HT
Mounting the Bike Handle
The following STIHL attachments may be mounted to the basic power tool:
STIHL power tool attachments are available for converting the single purpose FS unit into other power tool combinations.
Attachment Application
BF 1) Cultivator
2)3)
FCS
Power Edger FH 1) Power Scythe HL 0° 2) Hedge Trimmer HL 135°
1)2)
Hedge Trimmer
(adjustable) HT 2) Pole Pruner KB (4601) 2) Bristle Brush KW (4601) 2) PowerSweep KW (4602) 2) PowerSweep
1)
Barrier bar must be fitted on the
loop handle
2)
Not approved for use with bike-
handled units
3)
It is not necessary to use a shoulder strap
Removing Clamp Moldings
: Hold the lower clamp (1) and upper
clamp (2) firmly.
: Release the wing screw (3).
The clamps are loose once the wing screw has been released. They are pushed apart by the two springs (4 and 5).
: Pull out the wing screw.
Washer (6) remain at the tommy screw .
: Separate the clamps.
Springs (4) and (5) remain in the lower clamp.
22
FS 130, FS 130 R
Mounting the Handlebar
1
7
A
250BA046 KN
002BA234 KN
8
: Place the handlebar (7) in the lower
clamp (1) so that distance A is no more than 6 in (15 cm).
: Place the upper clamp in position
and hold both clamps together.
: Push the wing screw, with washer,
through the two clamps as far as stop – hold all parts together and secure them.
: Place the secured assembly on the
handle support (8) with the wing screw at the engine side.
: Push the wing screw into the handle
support as far as stop and then screw it down – but do not finally tighten yet.
: Line up the handlebar at a right
angle to the drive tube – check dimension A again.
: Tighten down the wing screw firmly
English / USA
Mounting the Control Handle
: Loosen the screw (9). The nut (10)
remains in the control handle (11).
: Push the control handle – throttle
trigger (12) must point toward the gearbox – onto the handlebar (7) so that the holes (13) line up.
: Insert screw and tighten down
firmly.
23FS 130, FS 130 R
English / USA
15
14
15
14
15
250BA002 KN
Mounting the Loop Handle
2
002BA098 KN
1
1
Fitting the Throttle Cable
Do not kink the throttle cable or lay it in tight radii – make sure the throttle trigger moves freely.
: Press the throttle cable (14) into the
retainers (15).
Throttle Cable Adjustment
: Go to chapter "Adjusting the
Throttle Cable".
24
Swiveling the Handlebar
Transport position:
: Release the wing screw (3) and
unscrew it until the handlebar (7) can be turned clockwise.
: Turn the handlebar 90° and then
swing the handles down.
: Tighten down the wing screw firmly.
Working position:
: Reverse the sequence described
above to swing the handles up and turn the handlebar counter­clockwise.
Loop handle with barrier bar
: Insert square nuts (1) in the
barrier bar (2).
: Line up the holes.
FS 130, FS 130 R
English / USA
5
4
002BA099 KN
2
3
6
7
4
5
002BA136 KN
1
6
1
3
8 7
8 7
10
9
4
002BA147 KN
A
: Place the clamp (3) in the loop
handle (4) and position them both against the drive tube (5).
: Fit the clamp (6) and place the
barrier bar (2) in position.
Note correct position.
: Line up the holes. : Insert screws (7) in holes and screw
them into the barrier bar as far as stop.
: Go to “Securing the loop handle”.
Loop handle without barrier bar
: Place the clamp (3) in the loop
handle (4) and position them both against the drive tube (5).
: Fit the clamp (6) and line up the
holes.
: Fit washers (7) on screws (8). : Insert screws (8) in holes and screw
on the square nuts (1) as far as stop.
: Go to “Securing the loop handle”.
Securing the loop handle
: Secure the loop handle (4)
approx. 8”/20cm (A) forward of the control handle (9).
: Line up the loop handle. : Tighten down the screws firmly –
lock the nuts if necessary.
10= Sleeve*
* see “Guide to Using this Manual”
25FS 130, FS 130 R
English / USA
Adjusting the Throttle Cable
002BA163 KN
STOP
249BA017 KN
1
2
Fitting the Carrying Eye
002BA142 KN
1
2
1
A properly adjusted throttle cable is the precondition for correct operation in the full throttle, starting throttle and idle positions.
Adjust the throttle cable only after the unit is fully assembled – the control handle must be in the normal operating position.
: Press down the trigger interlock (1)
and squeeze the throttle trigger (2) (full throttle) – this sets the throttle cable correctly.
: Use a suitable tool to push the slide
to the bottom of the slot (see illustration).
26
: For position of carrying eye1) see
"Parts and Controls"
: Place the clamp (1) with the
tapped hole on the left-hand side
of the drive tube.
: Squeeze the two ends of the clamp
together and hold in that position.
: Insert M 6 x 14 screw (2). : Line up the carrying eye. : Tighten down the screw firmly.
1) Included as standard or available as special accessory
FS 130, FS 130 R
English / USA
Mounting the Deflector
002BA102 KN
1
3
2
3
4
1
5
4
002BA103 KN
7 7
7
6
002BA028 KN
Mounting the deflector
1 = Deflector approved for all cutting
tools
2 = Deflector approved for use with
mowing heads only
: Place the deflector on the
gearhead.
: Fit the plate (3) and line it up. : Insert M 5 x 18 screws and tighten
down firmly.
Fitting skirt and blade
These parts must be fitted to the deflector (1) when you use a mowing head:
: Slide the lower guide slot of the
skirt (4) onto the deflector (1) – it must snap into position.
: Push the blade (5) into the upper
guide slot on the skirt and line it up with the first hole.
: Fit the screw and tighten it down
firmly.
Mounting the stop
: Always fit stop (6) when you use a
circular saw blade.
: Place the stop on the gearhead
flange.
: Fit the three M 5 x 18 screws (7) and
tighten down securely.
27FS 130, FS 130 R
English / USA
Mounting the Cutting Tools
002BA104 KN
2
002BA164 KN
1
3
4
5
Preparations
: Lay your brushcutter on its back
with the gearhead facing upward.
Mounting Hardware for Cutting Tools
The mounting hardware supplied depends on the cutting tool that comes as original equipment with the new brushcutter.
Mounting hardware is not packed with the machine
Only mowing heads may be mounted.
: Pull the hose (1) (protector for
shipping) off the shaft (2).
: Go to "Mounting the Mowing Head".
If you want to mount a metal cutting tool in place of a mowing head, you will need the following additional parts: Nut (3), rider plate (4) and thrust washer (5) (special accessories).
Mounting hardware is packed with the machine
Mowing heads and metal cutting tools may be mounted.
Mounting hardware is loose
: Pull the hose (1) (protector for
shipping) off the shaft (2).
The nut (3), rider plate (4) and thrust washer (5) are in the parts kit supplied with the machine.
: Go to "Mounting the Mowing Head"
or "Mounting Metal Cutting Tools".
Mounting hardware is secured to gearhead
: Go to "Removing Mounting
Hardware"
28
FS 130, FS 130 R
Removing Mounting Hardware
7
8
2
002BA166 KN
7
1
002BA081 KN
: Block the shaft – see next section
on "Blocking the Output Shaft".
: Use the combination wrench (6)
(supplied with machine or available as special accessory) to unscrew the nut (3) clockwise (left-hand thread) from the shaft (2).
: Pull the thrust washer (5) off the
shaft (2).
The rider plate (4) is in the parts kit supplied with the machine.
: Go to "Mounting the Mowing Head"
or "Mounting Metal Cutting Tools".
Blocking the Output Shaft
: Insert the stop pin or screwdriver (7)
(supplied with machine or available as special accessories) in the hole (8) in the gearhead as far as stop – apply slight pressure.
: Rotate nut or cutting tool on the
shaft (2) until the stop pin slips into position and blocks the shaft.
English / USA
Mounting the mowing head
Keep instruction sheet for mowing head in a safe place
: Screw the
STIHL SuperCut 20-2, STIHL AutoCut 25-2, 30-2 STIHL TrimCut 30-2 or STIHL PolyCut 20-3 counterclockwise onto the shaft (1) as far as stop.
: Block the output shaft. : Tighten down the mowing head.
Remove the stop pin.
29FS 130, FS 130 R
Loading...
+ 96 hidden pages