Sta-Rite HP10C User Manual
High-Pressure Booster Pumps
®
The HP/HPS Booster Pumps
are the most durable booster
pump available. The proven
SignaSeal™ floating impeller
design minimizes thrust loads
allowing for continuous operation without damage to motor
bearings, mechanical seal or
pump hydraulic components.
APPLICATIONS
■
Car wash
■
Filtration and reverse osmosis
■
Residential, commercial or
agricultural pressure washing
■
Booster and spray systems
■
HVAC
■
General purpose pumping
SPECIFICATIONS
Max. Inlet Pressure – 80 PSI
Max. Working Pressure – 315 PSI
Max. Suction Lift – 15 feet
Maximum Limits – Prolonged use
with liquids above 140
recommended.
Discharge –
HP Series: cast iron
HPS Series: stainless steel
Motor Adapter and Base –
HP Series: cast iron
HPS Series: stainless steel
Shell – Stainless steel 304 grade
Impeller – Acetal
Diffuser – Polycarbonate
Shaft – Stainless steel 304 grade
O-Rings – Buna-N
Mechanical Seal – Carbon/ceramic,
Buna-N
F is not
°
HP/HPS series
FEATURES
SignaSeal Staging System – The
proven SignaSeal staging system
utilizes a ceramic wear surface that,
when incorporated with Sta-Rite’s
“true” independent floating impellers,
dominates with 1st-in-class performance, superior sand handling and
thrust management staging system.
Acetal Impellers – Precisionmolded for perfect balance… ultrasmooth for highest performance
and efficiency.
Precision Molded Diffusers –
Superior performance with high
resistance to corrosion and abrasion
®
Mechanical Shaft Seal – Precision
lapped and highly polished carbonceramic, stainless steel construction.
Internal design guarantees continuous water lubrication.
Motor Windings – Superior
insu la tion materials protect against
excessive moisture and contaminants… assure prolonged motor life
Balanced Rotor – Die cast under
high pressures for uniform
performance and greater efficiency;
dynamically balanced
Heavy-duty Ball Bearings –
Shielded, permanently lubricated
bearings, extensively tested to
ensure extended life and smooth,
quiet operation.
Pump and Motor Shaft – Stainless
steel for maximum corrosion resistance; one-piece threaded shaft for
positive impeller drive
Dustproof Cover – All electrical
components are protected from dirt,
dust and insects by a dustproof
canopy; ventilating air cannot
contaminate.
Signature 2000® is a registered trademark of Pentair Water.
SignaSeal™ is a trademark of Pentair Water.
In order to provide the best products possible, specifications are subject to change.
Customer Service: (888) 782-7483
Fax Orders: (800) 426-9446 www.sta-rite.com
•
1
Pentair Water
•
Delavan, WI 53115 USA
•
S5609WS (5/11)
•
HP/HPS series
®
High-Pressure Booster Pumps
ORDERING INFORMATION
Catalog Number
Cast Iron Stainless Steel GPM HP Phase Stages Inlet Outlet Voltage Wt. (lbs.)
HP7C HPS7C 1/2 1 9 3/4" 3/4" 115/230 48
HP7C3 HPS7C3 1/2 3 9 3/4" 3/4" 208-230/460 45
HP7D HPS7D
HP7D3 HPS7D3 3/4 3 12 3/4" 3/4" 208-230/460 45
HP7E HPS7E 1 1 16 3/4" 3/4" 115/230 51
HP7E3 HPS7E3 1 3 16 3/4" 3/4" 208-230/460 48
HP10C HPS10C 1/2 1 6 3/4" 3/4" 115/230 45
HP10C3 HPS10C3 1/2 3 6 3/4" 3/4" 208-230/460 42
HP10D HPS10D 3/4 1 8 3/4" 3/4" 115/230 46
HP10D3 HPS10D3 3/4 3 8 3/4" 3/4" 208-230/460 43
HP10E HPS10E
HP10E3 HPS10E3 1 3 10 3/4" 3/4" 208-230/460 47
HP10F HPS10F 1-1/2 1 14 3/4" 3/4" 115/230* 58
HP10F3 HPS10F3 1-1/2 3 14 3/4" 3/4" 208-230/460 53
HP10G HPS10G 2 1 16 3/4" 3/4" 115/230* 63
HP10G3 HPS10G3 2 3 16 3/4" 3/4" 208-230/460 59
HP20E HPS20E 1 1 7 1" 1" 115/230 49
HP20E3 HPS20E3 1 3 7 1" 1" 208-230/460 46
HP20F HPS20F 1-1/2 1 9 1" 1" 115/230* 57
HP20F3 HPS20F3
HP20G HPS20G 2 1 11 1" 1" 115/230* 62
HP20G3 HPS20G3 2 3 11 1" 1" 208-230/460 58
HP20HG HPS20HG 2-1/2 1 13 1" 1" 115/230* 58
HP20HG3 HPS20HG3 2-1/2 3 13 1" 1" 208-230/460 54
HP20H HPS20H 3 1 15 1" 1" 208-230 59
HP20H3 HPS20H3 3 3 15 1" 1" 200-230/460 55
HP30E HPS30E 1 1 5 1-1/4" 1-1/4" 115/230 47
HP30E3 HPS30E3 1 3 5 1-1/4" 1-1/4" 208-230/460 44
HP30F HPS30F 1-1/2 1 6 1-1/4" 1-1/4" 115/230* 54
HP30F3 HPS30F3
HP30G HPS30G 2 1 7 1-1/4" 1-1/4" 115/230* 57
HP30G3 HPS30G3 2 3 7 1-1/4" 1-1/4" 208-230/460 53
HP30HG HPS30HG 2-1/2 1 9 1" 1" 115/230* 69
HP30HG3 HPS30HG3 2-1/2 3 9 1" 1" 208-230/460 54
HP30H HPS30H 3 1 11 1-1/4" 1-1/4" 208-230 59
HP30H3 HPS30H3 3 3 11 1-1/4" 1-1/4" 200-230/460 55
NOTE: ODP motor is standard, for TEFC motors, contact Customer Service. *HPS models 230V only.
3/4 1 12 3/4" 3/4" 115/230 48
7
1 1 10 3/4" 3/4" 115/230 50
10
1-1/2 3 9 1" 1" 208-230/460 52
20
1-1/2 3 6 1-1/4" 1-1/4" 208-230/460 49
30
Pipe Tapping Sizes
Motor Shipping
ORDERING INFORMATION
ACCESSORIES
Pkg. No. Description Approx. Wt. Lbs.
SUCTION
83 Suction hose – 3/4" 150 PSI hose, 6 ft. section with two (2) female hose fittings 3
85 Two (2) garden hose/NPT adapters – 3/4" NPT male to 3/4" garden hose male 3
96 Vacuum relief valve – 1/2" NPT 2
150 PSI RATED* DISCHARGE
84 Discharge hose – 3/4" 150 PSI hose, 25 ft. section with male and female garden hose fittings 10
86 High pressure pistol grip nozzle with three (3) nozzles (No. 56, 50 and 49) 2
315 PSI RATED* DISCHARGE
162 25' of 1" ID hose with 3/4" male and female hose fittings 315 PSI rating 15
194 High pressure pistol grip nozzle with three (3) nozzles (No. 56, 50 and 49) rated for 500 PSI 2
* To select proper discharge accessories for your
pump, add incoming pressure to pump output
pressure, to determine total discharge pressure.
Customer Service: (888) 782-7483
Fax Orders: (800) 426-9446 www.sta-rite.com
•
Example: Incoming pressure 20 PSI + pump output pressure (HP7C at 0 GPM, 300')
87 PSI = Total 150 PSI at discharge = 150 PSI rated discharge accessories
2
Pentair Water
•
Delavan, WI 53115 USA
•
S5609WS (5/11)
•
Loading...