Sta-Rite HMSD User Manual

HMS series
Horizontal Multi-Stage Jet/Centrifugal Pumps
FEATURES
Automatic Pressure Regulator –
Faster-acting and quieter, design eliminates “hunting” for correct drive pressure. New improved stem and guide are precisely molded to assure efficient, trouble-free performance on all deep wells. See ordering infor­mation (Deep well only).
Quality Construction – Close­grained cast iron pump body is rugged, one-piece unit, specially treated to resist corrosion. Drain port provided for easy winterizing.
Precision-machined Diffusers – Assure faster priming.
UL778/CSA108
HMS Series Multi-Stage Jet Pumps are the highest performing pumps available in its category.
APPLICATIONS
Water systems and sprinkling…
for homes, farms and cottages.
The HMS Series Convertible Jets utilize the built-in regulator, offering easier priming and better range of performance from a complete line of Shallow Well, 4" Double Pipe, 2" and 3" Single Pipe Jet Packages. Pump may also be operated as a self­priming centrifugal (to 25 ft.) to provide a wide range of high pressure applications.
SPECIFICATIONS
Body – One-piece rugged cast iron Pump and Motor Shaft – 416
stainless steel
Impeller – Polycarbonate Diffuser – Corrosion-resistant
cast iron
Pressure Switch Pre-Set – 30-50 PSI Suction Ports – Drive-over-Suction
ORDERING INFORMATION
Catalog
Number HP Description Suct. Drive Disch. Stages Voltage Wt. Lbs.
HMSD 3/4 Deep Well Jet 1-1/4" 1" 1" 2 115/230 50 HMSE 1 Deep Well Jet 1-1/4" 1" 1" 2 115/230 80 HMSF 1-1/2 Deep Well Jet 1-1/4" 1" 1" 2 115/230 85
AUTOMATIC PRESSURE REGULATOR – DEEP WELL
Catalog Approx. Number Description Application Wt. Lbs.
and compression fitting. installations.
Order pump and pressure regulator, if required, from ordering information tables above. A jet package and the automatic pressure regulator, described above, are required on
all deep well installations.
PRO-Source™ is a trademark of Pentair Water. In order to provide the best products possible, specifications are subject to change.
Regulator, tubing, pipe plug Required for ALL deep well
PKG 107
Pipe Tapping Sizes
Motor Approx.
4
Mechanical Shaft Seal – Precision lapped and highly polished carbon­ceramic, stainless steel construction. Internal design guarantees contin­uous water lubrication for maximum protection.
Polycarbonate Impellers – Precision molded for perfect balance, and ultra-smooth for highest performance and efficiency.
Motor Windings – Superior insulation materials protect against excessive moisture and contami­nants to ensure prolonged motor life.
Dustproof Cover – All electrical components are protected from dirt, dust and insects by a dust proof canopy. Ventilating air cannot contam inate vital switching compo­nents. This eliminates the most common cause of motor failure.
Balanced Rotor – Rotor is die cast under high pressures for uniform performance and greater efficiency; dynamically balanced.
Heavy-duty Ball Bearings – Shielded, permanently lubricated bearings are extensively tested to ensure extended life and smooth, quiet operation.
Pump and Motor Shaft – One piece threaded shaft for positive impeller drive and alignment. Shaft is stainless steel for maximum corrosion resistance.
Customer Service: (888) 782-7483
Fax Orders: (800) 426-9446 www.sta-rite.com
1
Pentair Water
Delavan, WI 53115 USA
S4511WS (5/11)
180
160
140
120
100
80
60
40
20
0102030405060
10'
10'
10'
15'
15'
15'
20'
20'
20'
25'
25'
25'
TOTAL HEAD IN FEET
CAPACITY GALLONS PER MINUTE
70
CAPACITY LITERS PER MINUTE
TOTAL HEAD IN METERS
100 250200500 150
50
40
30
20
10
0
HMSF
HMSE
HMSD
HMS series
Horizontal Multi-Stage Jet/Centrifugal Pumps
PUMP PERFORMANCE
SHALLOW WELL
Disch Catalog Jet* Uses Uses Press. Number HP Number Venturi Nozzle PSI 5' 10' 15' 20' 25'
20 9.6 8.2 7.0 5.8 3.9 30 9.1 7.9 6.5 5.6 3.9 40 8.8 7.7 6.3 5.6 3.9 HMSD 3/4 PKG 1 - 29SD N32P-66B J34P-41 50 8.5 7.6 6.2 5.6 3.9 60 7.7 7.3 6.2 5.6 3.9 70 5.5 5.1 4.7 4.2 3.6 80 3.5 3.1 2.8 2.3 1.9 Shut-Off 102 96 96 96 90 20 13.0 11.2 9.8 7.8 5.8 30 12.5 11.0 9.5 7.6 5.7 40 12.2 10.9 9.4 7.6 5.7 HMSE 1 PKG 1 - 10SD N32P-67B J34P-44 50 12.1 10.8 9.2 7.6 5.7 60 12.0 10.8 9.2 7.6 5.7 70 10.2 9.6 8.6 7.4 5.7 80 7.4 6.8 6.2 5.5 4.8 Shut-Off 108 108 108 102 102 20 15.9 13.3 12.2 9.6 7.0 30 15.6 13.2 12.2 9.5 7.0 40 15.3 13.1 12.1 9.4 6.9 50 14.9 13.0 11.9 9.3 6.8
HMSF 1-1/2 PKG 1 - 10SD N32P-67B J34P-44
70 13.7 12.7 11.5 9.0 6.6
60 14.4 12.9 11.7 9.2 6.7
80 12.6 12.1 10.8 8.7 6.4 90 9.5 8.5 7.8 7.2 5.7 100 5.9 5.0 4.4 3.8 3.2 Shut-Off 120 120 114 114 108
* Order Jet Package separately.
PUMP PERFORMANCE
Tested and rated in accordance with Water Systems Council standards.
NOTE: Pumps installed with a PRO-Source™ tank require
a 100 PSI relief valve. Pumps installed with a conventional tank require a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
Total Suction Lift Ft.
Customer Service: (888) 782-7483
Fax Orders: (800) 426-9446 www.sta-rite.com
2
NOTE: Dotted lines indicate performance reduction at high
suction lift.
Pentair Water
Delavan, WI 53115 USA
S4511WS (5/11)
Loading...
+ 2 hidden pages