Stanford Research Systems SR830 Data Sheet

· 1 mHz to 102.4 kHz frequency range

· >100 dB dynamic reserve

· 5 ppm/°C stability

· 0.01 degree phase resolution

· Time constants from 10

µµ

s to 30 ks

(up to 24 dB/oct rolloff)

· Auto gain, phase, reserve and offset

· Synthesized reference source

· GPIB and RS-232 interfaces

· SR810 ... $3650

(U.S. list)

· SR830 ... $3950

(U.S. list)

Stanford Research Systems phone: [phone]

www.thinkSRS.com

The SR810 and SR830 DSP Lock-In Amplifiers provide high
performance at a reasonable cost. The SR830 simultaneously
displays the magnitude and phase of a signal, while the SR810
displays the magnitude only. Both instruments use digital
signal processing (DSP) to replace the demodulators, output
filters and amplifiers found in conventional lock-ins. The
SR810 and SR830 provide uncompromised performance with
an operating range of 1 mHz to 102 kHz and 100 dB of drift­free dynamic reserve.

Input Channel

The SR810 and SR830 have differential inputs with 6 nV/√Hz
input noise. The input impedance is 10 MΩ and minimum
full-scale input voltage sensitivity is 2 nV. The inputs can also
be configured for current measurements with selectable
current gains of 10

6

and 108V/A. A line filter (50 Hz or

60 Hz) and a 2× line filter (100 Hz or 120 Hz) are provided to
eliminate line related interference. However, unlike
conventional lock-in amplifiers, no tracking band-pass filter is
needed at the input. This filter is used by conventional lock-ins
to increase dynamic reserve. Unfortunately, band pass filters
also introduce noise, amplitude and phase error, and drift. The
DSP design of these lock-ins has such inherently large
dynamic reserve that no band pass filter is needed.

Extended Dynamic Reserve

The dynamic reserve of a lock-in amplifier at a given full­scale input voltage is the ratio (in dB) of the largest interfering

SR810/SR830 DSP Lock-In Amplifiers

Digital Lock-In Amplifiers

SR810 and SR830  DSP lock-in amplifiers

www.thinkSRS.com

SR810 and SR830 DSP Lock-In Amplifiers

Stanford Research Systems phone: [phone]

www.thinkSRS.com

signal to the full-scale input voltage. The largest interfering
signal is defined as the amplitude of the largest signal at any
frequency that can be applied to the input before the lock-in
cannot measure a signal with its specified accuracy.

Conventional lock-in amplifiers use an analog demodulator to
mix an input signal with a reference signal. Dynamic reserve
is limited to about 60 dB, and these instruments suffer from
poor stability, output drift and excessive gain and phase error.
Demodulation in the SR810 and SR830 is accomplished by
sampling the input signal with a high-precision A/D converter,
and multiplying the digitized input by a synthesized reference
signal. This digital demodulation technique results in more
than 100 dB of true dynamic reserve (no prefiltering) and is
free of the errors associated with analog instruments.

Digital Filtering

The digital signal processor also handles the task of output
filtering, allowing time constants from 10 µs to 30,000 s with
a choice of 6, 12, 18 and 24 dB/oct rolloff. For low frequency
measurements (below 200 Hz), synchronous filters can be
engaged to notch out multiples of the reference frequency.
Since the harmonics of the reference have been eliminated
(notably 2F), effective output filtering can be achieved with
much shorter time constants.

Digital Phase Shifting

Analog phase shifting circuits have also been replaced with a
DSP calculation. Phase is measured with 0.01° resolution and
the X and Y outputs are orthogonal to 0.001°.

Frequency Synthesizer

The built-in direct digital synthesis (DDS) source generates a
very low distortion (−80 dBc) reference signal. Single
frequency sine waves can be generated from 1 mHz to 102 kHz
with 4½ digits of resolution. Both frequency and amplitude
can be set from the front panel or from a computer. When
using an external reference, the synthesized source is phase
locked to the reference signal.

Useful Features

Auto-functions allow parameters that are frequently adjusted
to automatically be set by the instrument. Gain, phase, offset
and dynamic reserve are quickly optimized with a single key
press. The offset and expand features are useful when
examining small fluctuations in a measurement. The input

signal is quickly nulled with the auto-offset function, and
resolution is increased by expanding around the relative value
by up to 100×. Harmonic detection isn’t limited to 2Fany
harmonic (2F, 3F, ... nF) up to 102 kHz can be measured.

Analog Inputs and Outputs

Both instruments have a user-defined output for measuring X,
R, X-noise, Aux 1, Aux 2 or the ratio of the input signal to an
external voltage. The SR830 has a second user-defined output
that measures Y, θ, Y-noise, Aux 3, Aux 4 or ratio. The SR810
and SR830 both have X and Y analog outputs (rear panel) that
are updated at 256 kHz. Four auxiliary inputs (16-bit ADCs)
are provided for general purpose use, like normalizing the
input to source intensity fluctuations. Four programmable
outputs (16-bit DACs) provide voltages from −10.5 V to
+10.5 V and are settable via the front panel or computer
interfaces.

Internal Memory

The SR810 has an 8,000 point memory buffer for recording
the time history of a measurement at rates up to 512 samples/s.
The SR830 has two, 16k point buffers to simultaneously
record two measurements. Data is transferred from the buffers
using the computer interfaces. A trigger input is also provided
to externally synchronize data recording.

Easy Operation

The SR810 and SR830 are simple to use. All functions are set
from the front-panel keypad, and a spin knob is provided to
quickly adjust parameters. Up to nine different instrument
configurations can be stored in non-volatile RAM for fast and
easy instrument setup. Standard RS-232 and GPIB (IEEE-488.2)
interfaces allow communication with computers.

Ordering Information

SR830 DSP dual phase lock-in $3950

amplifier (w/ rack mount)

SR810 DSP single phase lock-in $3650

amplifier (w/ rack mount)

SR550 Voltage preamplifier $595

(100 MΩ, 3.6 nV/√Hz)

SR552 Voltage preamplifier $595

(100 kΩ, 1.4 nV/√Hz)

SR554 Transformer preamplifier $995

(0.091 nV/√Hz)

SR540 Optical chopper $1095

SR810 DSP Single Phase Lock-In Amplifier

SR810/830 rear panel

SR810 and SR830 Specifications

Signal Channel

Voltage inputs Single-ended or differential
Sensitivity 2 nV to 1 V
Current input 10

6

or 108V/A

Input impedance

Voltage 10 MΩ + 25 pF, AC or DC coupled
Current 1 kΩ to virtual ground

Gain accuracy ±1 % (±0.2 % typ.)
Noise (typ.) 6 nV/√Hz at 1 kHz

0.13 pA/√Hz at 1 kHz (10

6

V/A)

0.013 pA/√Hz at 100 Hz (10

8

V/A)
Line filters 50/60 Hz and 100/120 Hz (Q=4 )
CMRR 100 dB to 10 kHz, decreasing by

6 dB/oct above 10 kHz
Dynamic reserve >100 dB (without prefilters)
Stability <5 ppm/°C

Reference Channel

Frequency range 0.001 Hz to 102.4 kHz
Reference input TTL or sine (400 mVpp min.)
Input impedance 1 MΩ, 25 pF
Phase resolution 0.01° front panel, 0.008° through

computer interfaces
Absolute phase error <1°
Relative phase error <0.001°
Orthogonality 90° ± 0.001°
Phase noise

Internal ref. Synthesized, <0.0001° rms at 1 kHz
External ref. 0.005° rms at 1 kHz (100 ms time

constant, 12 dB/oct)
Phase drift <0.01°/°C below 10 kHz,

<0.1°/°C above 10 kHz
Harmonic detection 2F, 3F, ... nF to 102 kHz (n<19,999)
Acquisition time (2 cycles + 5 ms) or 40 ms,

whichever is larger

Demodulator

Stability Digital outputs and display: no drift.

Analog outputs: <5 ppm/°C for all

dynamic reserve settings.
Harmonic rejection −90 dB
Time constants 10 µs to 30 ks (6, 12, 18, 24 dB/oct

rolloff). Synchronous filters

available below 200 Hz.

Internal Oscillator

Range 1 mHz to 102 kHz
Frequency accuracy 25 ppm + 30 µHz
Frequency resolution 4½ digits or 0.1 mHz, whichever

is greater.
Distortion −80 dBc (f <10 kHz), −70 dBc

(f >10 kHz) @ 1 Vrms amplitude
Amplitude 0.004 to 5 Vrms into 10 kΩ (2 mV

resolution). 50 Ω output impedance.

50 mA maximum current into 50 Ω.
Amplitude accuracy 1 %
Amplitude stability 50 ppm/°C

Outputs Sine, TTL. (When using an external

reference, both outputs are phase
locked to the external reference)

Displays

Channel 1 4½-digit LED display with

40-segment LED bar graph. X, R,
X-noise, Aux 1 or Aux 2. The
display can also be any of these
quantities divided by Aux 1 or Aux 2.

Channel 2 (SR830) 4½-digit LED display with

40-segment LED bar graph. Y, θ,
Y-noise, Aux 3 or Aux 4. The display
can also be any of these quantities
divided by Aux 3 or Aux 4.

Offset X, Y, R can be offset up to ±105 %

of full scale.

Expand X, Y, R can be expanded by 10×

or 100×.

Reference 4½-digit LED display

Inputs and Outputs

CH1 output ±10 V output of X, R, X-noise,

Aux 1 or Aux 2. Updated at 512 Hz.

CH2 output (SR830) ±10 V output of Y, θ, Y-noise,

Aux 3 or Aux 4. Updated at 512 Hz.

X, Y outputs In-phase and quadrature components

(rear panel) (±10 V). Updated at 256 kHz.

Aux. A/D inputs 4 BNC inputs, 16-bit, ±10 V,

1 mV resolution, sampled at 512 Hz

Aux. D/A outputs 4 BNC outputs, 16-bit, ±10 V,

1 mV resolution
Sine out Internal oscillator analog output
TTL out Internal oscillator TTL output
Data buffer The SR810 has an 8k point buffer.

The SR830 has two 16k point

buffers. Data is recorded at rates to

512 Hz and read through the

computer interfaces.
Trigger in (TTL) Trigger synchronizes data recording
Remote preamp Provides power to the optional

SR550, SR552 and SR554 preamps.

General

Interfaces IEEE-488.2 and RS-232 interfaces

standard. All instrument functions

can be controlled and read through

IEEE-488.2 or RS-232 interfaces.
Power 40 W, 100/120/220/240 VAC,

50/60 Hz
Dimensions 17" × 5.25" × 19.5" (WHD)
Weight 23 lbs.
Warranty One year parts and labor on defects

in materials and workmanship

Stanford Research Systems phone: [phone]

www.thinkSRS.com