7 to 10-inch multi-touch capacitive touchscreen controller
Features
■ True multi-touch:
– Independent XY tracking with 10
simultaneous touches in real time
– Up to 23 force and 32 sense channels
■ Single chip solution:
– Up to 10 inches screen size
– Supports multiple touchscreen
configurations including touch keys with no
external components on touch channels
– Separate touch key support
■ High SNR:
– Common mode charger noise rejection up
to 40 Vpp
– Advanced filtering techniques for strong
noise immunity
■ Fast report rate: > 150 Hz
■ High response time: < 2x report rate
■ Power consumption:
– 13 mW in active mode (multi-touch)
– 5 µW in sleep mode
■ 32-bit RISC processor
– Flexibility for customer code
implementation
– Allows customization of proprietary touch
pattern and gestures
■ Multiple input types: finger and stylus pen
– Up to 2 mm stylus
– Simultaneous finger and stylus
– Stylus recognition with palm rejection
Table 1. Device summary
STMT07
S-Touch® FingerTip
Data brief
LGA84
(5.5 x 5.5 mm)
■ Large area recognition and rejection
■ Advanced signal processing and calibration:
– Water recovery, self-calibration with auto-
drift compensation and fast start-up
– Hardware coordinate scalar to match
touchscreen and display resolution
– Supports axis flipping and axis switch-over
for portrait and landscape modes
■ Sensor types:
– Works with plastic or glass sensors, with
different types of sensor patterns with or
without ground shield
– Supports on-cell, laminated and touch-on-
lens touch display
■ Power supply scheme:
– 2.8 V to 5 V A
■
Serial interface:
– Supports high speed I
– 3.3 V tolerant interface for I
■ I/Os: RESETB, INTB hardware pins to host
interface and 11 GPIOs with full
programmability
■ High ESD protection:
– ±8 KV HBM ESD protection on all the force
and sense pins including self sense keys
and 1.8 V D
VDD
2
C and SPI
2
C and SPI
VDD
Order code Package Packing
STMT07N1LTR
June 2011 Doc ID 018915 Rev 1 1/4
For further information contact your local STMicroelectronics sales office.
LGA84 (5.5 x 5.5 mm);
0.5 mm pitch and 0.55 mm thick
Tape and reel
www.st.com
4
Description STMT07
1 Description
The STMT07 device represents a marked improvement over competing technologies by
providing an optimal mix of low power, small size, feature flexibility with unmatched true
multi-touch performance in a single-chip touchscreen controller.
The FingerTip STMT07 uses a unique capacitance to voltage conversion acquisition engine
to implement the S-Touch
®
capacitive sensing method. Coupled with the flexibility offered by
the internal processor engine, the entire touchscreen sensing solution can measure, classify
and track a single finger touch with fast report rate and response times on 736 nodes. Builtin movement tracking engine tracks greater than 10 independent touch movements.
The acquisition engine uses an optimal measurement approach to ensure almost complete
immunity from parasitic capacitance on the receiver inputs (sense lines). The engine
includes sufficient dynamic range to cope with touchscreens of different size and
configuration. This offers great flexibility to use with multiple touchscreens with different ITO
designs and overlay materials. One and two layer ITO sensors are possible using glass or
PET substrates.
The STMT07's capacitive analog front-end provides enhanced noise suppression
capabilities for various noise sources such as display, human body captured noise, system
generated noise and severe common mode noise introduced by battery chargers. ST’s
advanced capacitive sensing technology coupled with a powerful digital 32-bit DSP engine
is able to address common mode noise to provide high level of noise immunity without
reducing the overall touch performance in terms of response time, frame rate and power
consumption.
The device has an external SYNC pin for LCD noise filtering for an "on-cell" display
touchscreen technology. The synchronization of the signal acquisition with the LCD SYNC
signal helps in removal of LCD noise. This benefits the touch module maker to employ glass
screens with ITO to be used without any GND shield that can significantly reduce the cost of
the touch module.
The STMT07 supports multiple input types including stylus detection (up to 2 mm) for
smooth handwriting capability on touchscreens while detecting and rejecting large area
such as palm or hand. The device also supports touchkeys using the same ITO.
The main processor engine offers flexibility with required performance by an efficient preprocessing, post-processing and house-keeping. This gives ample scope for sensing
algorithm, touch tracking or advanced shape based filtering, area definition and event
reporting. Built-in associated processor memory (ROM, RAM) is optimized to run the
desired fixed program codes in the ROM and to maintain the data, event stack and system
variables in a RAM. An additional patch RAM can be used for implementing customized
codes or algorithms.
Besides I
2
I
C bus and providing more flexibility.
2/4 Doc ID 018915 Rev 1
2
C serial interface, the device supports a SPI interface freeing up the overloaded
STMT07 Revision history
2 Revision history
Table 2. Document revision history
Date Revision Changes
10-Jun-2011 1 Initial release.
Doc ID 018915 Rev 1 3/4
STMT07
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4 Doc ID 018915 Rev 1
Loading...