Sony XBR-75X900H Users guide [en, fr]

Wall-Mount
Bracket

Installation Information

Informations d’installation

Información para la instalación

US

FR

ES

SU-WL855

Lea este manual antes de usar
el producto

E-624-100-11(1)

Installation Information for
Using Sony Wall-Mount Bracket (SU-WL855)

Supported models*:
XBR-75X9xxH / 65X9xxH / 55X9xxH
XBR-75X90CH / 65X90CH / 55X90CH
FW-75BZ40H / 65BZ40H / 55BZ40H

*

In the actual model names, the “xx“ indicates numbers and/or characters specific to each model.

To Customers
For product protection and safety reasons, Sony strongly recommends that installation of your TV or
LCD Display be performed by Sony dealers or licensed contractors. Do not attempt to install it
yourself.

To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.

Sufficient expertise is required for installing this product, especially to determine the
strength of the wall for withstanding the TV’s or LCD Display’s weight. Be sure to
entrust the attachment of this product to the wall to Sony dealers or licensed
contractors and pay adequate attention to safety during the installation. Sony is not
liable for any damage or injury caused by mishandling or improper installation.

For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV or LCD
Display Setup Guide and the directions in this manual.

− 2 (US) −

Wall-Mount Bracket

On Safety

Thank you for purchasing this product.

To Customers

Installing the TV or LCD Display to the
Wall

WARNING

PROFESSIONAL INSTALLATION REQUIRED

This product should only be installed by
a professional installer who is trained to
determine the strength of the wall for
withstanding the TV’s or LCD Display’s
weight. If it is not properly secured
during installation, the TV or LCD Display
may fall and cause serious injury. Sony is
not liable for any damage or injury
caused by mishandling or improper
installation, or installing any other than
the specified product. Your Statutory
Rights (if any) are not affected.

To Sony dealers

Sufficient expertise is required for
installing this product. Be sure to read
this instruction manual thoroughly to do
the installation work safely. Sony is not
liable for any damages or injury caused
by mishandling or improper installation.
Please give this manual to the customer
after installation.

This instruction manual shows the correct
handling of the product and important
precautions necessary to prevent accidents.
It is your responsibility to read, thoroughly
understand, and follow all instructions in this
instruction manual. Failure to do so may
result in serious personal injury or property
damage, and may void the warranty. Keep
this manual available for future reference.

Products by Sony are designed with safety in
mind. If the products are used incorrectly,
however, it may result in a serious injury
through fire, electric shock, the product
toppling over, or the product dropping. Be
sure to observe the precautions for safety to
prevent such accidents.

CAUTION

Specified products

This Wall-Mount Bracket is designed for use
with the products specified TVs or LCD
Displays. For TVs or LCD Displays or LCD
Displays, refer to their “Reference Guide” to
verify that the Wall-Mount Bracket can be
used.

To Customers

WARNING

If the following precautions are not
observed, serious injury or death
through fire, electric shock, or the
product dropping can result.

Be sure to subcontract
the installation to
licensed contractors and
keep small children away
during the installation.

If the Wall-Mount Bracket or the TV or LCD
Display is not installed correctly, the
following accidents may occur. Be sure
licensed contractors carry out installation.

The TV or LCD Display may fall and cause a



serious injury such as a bruise or a fracture.
If the wall on which the Wall-Mount



Bracket is installed is unstable, uneven, or
not perpendicular to the floor, the unit
may fall and cause injury or property
damage. The wall should be capable of
supporting a weight of at least six times
the TV or LCD Display weight.
(Refer to your TV’s or LCD Display’s
“Reference Guide” for its weight.)
If the installation of the Wall-Mount



Bracket on the wall is not sufficiently
sturdy, the unit may fall and cause injury or
property damage.

Be sure to subcontract
moving or dismounting
of the TV or LCD Display
to licensed contractors.

If persons other than licensed contractors
transport or dismount the TV or LCD Display,
it may fall and cause injury or property
damage. Be sure that two or more persons
carry or dismount the TV or LCD Display.

Do not remove screws,
etc., after mounting the
TV or LCD Display.

If you do so, the TV or LCD Display may fall
and cause injury or property damage.

Do not make alterations
to the parts of the Wall­Mount Bracket.

If you do so, the Wall-Mount Bracket may fall
and cause injury or property damage.

Do not mount any
equipment other than
the specified product.

This Wall-Mount Bracket is designed for use
with the specified product only. If you mount
equipment other than specified, it may fall or
break, and cause injury or property damage.

Do not apply any load
other than the TV or LCD
Display on the Wall­Mount Bracket.
Do not shake the TV or
LCD Display left/right,
up/down.

If you do so, the TV or LCD Display may fall
and cause injury or property damage.

Do not lean on or hang
from the TV or LCD
Display.

Do not lean on or hang from the TV or LCD
Display as it may fall on you and cause
serious injury.

CAUTION

If the following precautions are not
observed, injury or property damage
may occur.

Be careful to not pinch your fingers while



handling the Wall-Mount Bracket or
swiveling the TV or LCD Display set.
While swiveling the TV or LCD Display set,



handle it with caution and take care not to
hit any people nearby.
Be sure to store the unused parts in a safe



place for future use.
Keep them away from children.

Do not handle the
product with excessive
force during cleaning or
maintenance.

Do not apply excessive force on the topside
of the TV or LCD Display. If you do so, the TV
or LCD Display may fall and cause injury or
property damage.

Notice

If you use the TV or LCD Display installed



on the Wall-Mount Bracket for a long time,
the wall behind or above the TV or LCD
Display may become discolored or the
wallpaper may come unstuck, depending
on the material of the wall.
If the Wall-Mount Bracket is removed after



installing it on the wall, the screw holes are
left.
Do not use the Wall-Mount Bracket in a



place where it is subjected to mechanical
vibrations.

US

− 3 (US) −

Installing the Wall­Mount Bracket

To Sony Dealers

WARNING

The following instructions are for Sony
dealers only. Be sure to read safety
precautions described above and pay
special attention to safety during the
installation, maintenance and checking
of this product.

Be sure to install the
Wall-Mount Bracket
securely to the wall
following the instructions
in this instruction
manual.

If any of the screws are loose or fall out, the
Wall-Mount Bracket may fall and cause injury
or property damage. Be sure to use the
appropriate screws for the material of the
wall and install the unit securely using
supplied screws and anchors.

Be sure to tighten the
screws securely in the
designated position.

If you fail to do so, the TV or LCD Display may
fall and cause bodily injury to someone or
damage to the TV or LCD Display.

Be careful not to subject
the TV or LCD Display to
shock during installation.

If the TV or LCD Display is exposed to shock,
it may fall or break apart. This may cause
injury.

Do not install the Wall­Mount Bracket on wall
surfaces where the
corners or the sides of
the TV or LCD Display
protrude away from the
wall surface.

Do not install the Wall-Mount Bracket on wall
surfaces such as a pillar, where the corners
or the sides of the TV or LCD Display
protrude away from the wall surface. If a
person or object happens to hit the
protruded corner or side of the TV or LCD
Display, it may cause injury or property
damage.

Do not install the TV or
LCD Display over or
under an air-conditioner.

If the TV or LCD Display is exposed to water
leaks or air current from an air conditioner
for a long time, it may cause a fire, an electric
shock or a malfunction of the TV or LCD
Display.

Be sure to use the
supplied screws and
attachment parts
properly following the
instructions given in
this instruction
manual. If you use
substitute items, the
TV or LCD Display may
fall and cause bodily
injury to someone or
damage to the TV or
LCD Display.

Be sure to install the TV
or LCD Display on a wall
that is both
perpendicular and flat.

If you fail to do so, the TV or LCD Display may
fall and cause injury.

After proper installation
of the TV or LCD Display,
secure the cables
properly.

If people or objects get tangled with cables,
this may result in injury or damage to the TV
or LCD Display.

Do not allow the AC
power cord or the
connecting cable to be
pinched.

If the AC power cord or the connecting cable
is pinched between the unit and the wall or
is bent or twisted by force, the internal
conductors may become exposed and cause
a short circuit or an electrical break. This may
cause a fire or an electric shock.

Be sure to assemble the
bracket properly
following the instructed
procedure explained in
this instruction manual.

If any of the screws are loose or fall out, the
TV or LCD Display may fall and cause bodily
injury to someone or damage to the TV or
LCD Display.

− 4 (US) −

Before getting started

Firstly, check the type of the wall to install the TV or LCD Display.
The Wall-Mount Bracket differs depending on the type of the wall.

What is your wall made of?

Dry wall with studs

Precautions

Maximum dry wall thickness:



16 mm (5/8 inch).
Ensure that the inner wood stud size is at



least 51 x 102 mm (2 x 4 inch) for common
or 38 x 89 mm (1 1/2 x 3 1/2 inch) for
nominal.
Keep minimum 406 mm (16 inch) horizontal



space between fasteners.

Use the Lateral Shift Bracket.

+

Solid Concrete or Concrete Block

Precautions

Mount the Wall-Mount Bracket directly



onto the solid concrete wall.
Ensure that the thickness of solid concrete



wall is at least 203 mm (8 inch).
Ensure that the size of each concrete block



is at least 203 x 203 x 406 mm
(8 x 8 x 16 inch).

Use the Wall-Mount Bracket.

US

− 5 (US) −

Preparing for installation

Have the TV’s or LCD Display’s Reference



Guide and Setup Guide at hand before
installation.
Confirm the installing position of your TV or



LCD Display.

Checking the parts

Supplied with SU-WL855

Verify that all the parts are included.



 WM1  WM2

 WM4  M6 (4)

 WS1 (4)  WS2 (6)

Supplied with the TV or LCD Display

VS

Wall-Mount

Attachment (4)

8 mm x 12 mm
(11/32 inch x 1/2 inch)

 WW1 (6)  WW2 (4)

 WA1 (4)  WT1 (6)

 WM3 (4)

8 mm x 60 mm
(11/32 inch x 2 3/8 inch)

− 6 (US) −

Tools needed

*1

*2

*1Only for dry wall with studs
*2Only for solid concrete or concrete block
*3Depending on models

5.5 mm

(7/32 inch)

1.5 N.m/1,5 N.m
{15 kgf.cm}

10 mm

(13/32 inch)

*3

1.5 N.m/1,5 N.m
{15 kgf.cm}

13 mm

(1/2 inch)

12.5 N.m/12,5 N.m
{130 kgf.cm}

US

− 7 (US) −

 Attaching TV or LCD Display to the Dry Wall with Studs

Dry wall with studs

WM4

WM1

+

Installing the Lateral Shift Bracket to the wall

1 Decide on the installation location.

Make sure that the wall has enough space for the TV or LCD Display and is capable of supporting
a weight of at least six times that of the TV or LCD Display.
Refer to the following table on installing the TV or LCD Display to the wall. Refer to your TV’s or
LCD Display’s Reference Guide for the TV’s or LCD Display’s weight.

*1

− 8 (US) −

(mm/inch)

g

f

g

*2

Model Name

XBR-75X9xxH
XBR-75X90CH

FW-75BZ40H

XBR-65X9xxH
XBR-65X90CH

FW-65BZ40H

XBR-55X9xxH
XBR-55X90CH

FW-55BZ40H

1,674 /

66

1,674 /

66

1,450 /

57 1/8

1,450 /

57 1/8

1,231 /
48 1/2

1,231 /
48 1/2

961 /

37 7/8

961 /

37 7/8

833 /

32 7/8

833 /

32 7/8

710 /

28

710 /

28

447 /

17 5/8

447 /

17 5/8

446 /

17 5/8

446 /

17 5/8

446 /

17 5/8

446 /

17 5/8

-38 /

-1 1/2*

-38 /

-1 1/2*

26 /

1 1/16

26 /

1 1/16

87 /

3 1/2

87 /

3 1/2

94 /

3 3/4

95 /

3 3/4

92 /

3 5/8

93 /

3 3/4

92 /

3 5/8

93 /

3 3/4

f

298 15

298 15

296 18

296 18

296 20

296 20

* Bracket positioning is below the screen center point.

TV or LCD Display installation dimensions table (mm/inch)
Figures in the table may differ slightly depending on the installation.

*1 (Screen center point)
*2 (Approx.)

Note

When your TV or LCD Display is installed on the wall, the upper side of the TV or LCD Display slightly leans forward.



*2

(°)

US

− 9 (US) −

Note

We recommend you to check the



position of TV or LCD Display in the
viewing environment.

4 Drill upper pilot holes on the

marks.

75 mm
(3 inch)

5.5 mm
(7/32 inch)

Note

Pilot holes must be drilled to a depth of 75 mm



(3 inch), using a 5.5 mm (7/32 inch) diameter drill bit.

2

3 Align

make four marks aligned with
the studs.

WM4

WM4

to the wall and

5 Install

WM4

on the wall.

WW1

WS2

Note

Use a level to check whether



Precaution

Do not over-tighten the lag bolts



tightening could reduce the holding power of the lag
bolts

WS2

.

WM4

is level.

WS2

. Improper

6 Drill lower pilot holes on the

marks. (Refer step 4 for the drill
instruction.)

Note

Use a level to check whether



WM4

is level.

− 10 (US) −

7 Fit the screws and spacers to

the holes.

Note

Use a level to check whether the Wall-Mount Bracket



is level.

WW1

WS2

8

WM1

WW2

Preparing for the installation
of the TV or LCD Display

Make sure to attach the Table-Top stand
before installing the TV or LCD Display to the
wall by referring to the Setup Guide.

1 Remove the screws from the

rear of the TV or LCD Display.

US

WS1

9 Pull out the arm of the bracket

to the end.

Note

Be sure to store the removed screws and unused



parts in a safe place, keeping them away from
children.

2 Attach the Wall-Mount

Attachment (supplied with the
TV or LCD Display) to the rear of
the TV or LCD Display (to make
it parallel with the wall).

1.5 N·m
{15 kgf·cm}

VS

− 11 (US) −

3 Attach

WM3

.

WM3

5 Detach the Table-Top Stand

from the TV or LCD Display.

Remove one side of the Table-Top Stand



at a time. Firmly hold the Table-Top
Stand securely with both hands while
the other people lift up the TV or LCD
Display.

4 Attach the

WM2

LCD Display using

M6

to the TV or

M6

WM2

.

Repeat the previous step and remove



the other side of the Table-Top Stand.

Note

Three or more people are required to detach the



Table-Top Stand.
Be careful not to use excessive force while detaching



the Table-Top Stand from the TV or LCD Display as it
may cause the TV or LCD Display set to fall resulting
in personal injury or physical damage to the TV or
LCD Display.
Take care when handling the Table-Top Stand to



prevent damage to the TV or LCD Display.
Be careful when lifting the TV or LCD Display as the



Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
Take care when removing the Table-Top Stand from



the TV or LCD Display to prevent it from falling over
and damaging the surface that the TV or LCD Display
is sitting on.
Be sure to store the removed screws and unused



parts in a safe place, keeping them away from
children.

− 12 (US) −

Installing the TV or LCD
Display on the wall

1

3 Screw the left and right side of

the Wall-Mount Bracket.

2

M6

US

M6

− 13 (US) −

4

5 When moving the TV or LCD

Display, hold it firmly from the
bottom.

WARNING

Be sure that two or more persons (three or more



persons for 75 inches and above TV or LCD Display
set) hold the TV or LCD Display when carrying it.

Confirming the completion of
the installation

Check the following points.

The cord and the cable are not twisted or



pinched.

WARNING

Improper placement of the AC power cord, etc. may cause



fire or electric shock through a short circuit. Be sure to
confirm the completion of the installation for safety.

6

Other information

When removing the TV or LCD Display, reverse
the previous installation procedure.

WARNING

Be sure that two or more persons (three or more persons



for 75 inches and above TV or LCD Display set) hold the TV
or LCD Display when removing it.

− 14 (US) −

 Attaching the Wall-Mount Bracket to the Solid Concrete or

Concrete Block

Solid Concrete or Concrete Block

WM1

Installing the Wall-Mount Bracket to the wall

1 Decide on the installation location.

Make sure that the wall has enough space for the TV or LCD Display and is capable of supporting
a weight of at least six times that of the TV or LCD Display.
Refer to the following table on installing the TV or LCD Display to the wall. Refer to your TV’s or
LCD Display’s Reference Guide for the TV’s or LCD Display’s weight.

*1

US

− 15 (US) −

(mm/inch)

g

f

g

*2

Model Name

XBR-75X9xxH
XBR-75X90CH

FW-75BZ40H

XBR-65X9xxH
XBR-65X90CH

FW-65BZ40H

XBR-55X9xxH
XBR-55X90CH

FW-55BZ40H

1,674 /

66

1,674 /

66

1,450 /

57 1/8

1,450 /

57 1/8

1,231 /
48 1/2

1,231 /
48 1/2

961 /

37 7/8

961 /

37 7/8

833 /

32 7/8

833 /

32 7/8

710 /

28

710 /

28

363 /

14 3/8

363 /

14 3/8

362 /

14 3/8

362 /

14 3/8

362 /

14 3/8

362 /

14 3/8

-122 /

-4 7/8*

-122 /

-4 7/8*

-59 /

-2 3/8*

-59 /

-2 3/8*

3 /

1/8

3 /

1/8

84 /

3 3/8

85 /

3 3/8

82 /

3 1/4

83 /

3 3/8

82 /

3 1/4

83 /

3 3/8

f

288 15

288 15

286 18

286 18

286 20

286 20

* Bracket positioning is below the screen center point.

TV or LCD Display installation dimensions table (mm/inch)
Figures in the table may differ slightly depending on the installation.

*1 (Screen center point)
*2 (Approx.)

Note

When your TV or LCD Display is installed on the wall, the upper side of the TV or LCD Display slightly leans forward.



*2

(°)

− 16 (US) −

Note

We recommend you to check the



position of TV or LCD Display in the
viewing environment.

4

WA1

2 Align

WM1

make four marks.

WM1

Note

Use a level to check whether



to the wall and

WM1

is level.

5 Install

WM1

on the wall.

WW1

WS2

Note

Use a level to check whether



Precaution

Do not over-tighten the lag bolts



tightening could reduce the holding power of the lag
bolts

WS2

.

WM1

is level.

WS2

. Improper

6 Pull out the arm of the bracket

to the end.

US

3 Drill pilot holes on the marks.

75 mm
(3 inch)

10 mm
(13/32 inch)

− 17 (US) −

Preparing for the installation
of the TV or LCD Display

Make sure to attach the Table-Top stand
before installing the TV or LCD Display to the
wall by referring to the Setup Guide.

3 Attach

WM3

.

WM3

1 Remove the screws from the

rear of the TV or LCD Display.

Note

Be sure to store the removed screws and unused



parts in a safe place, keeping them away from
children.

2 Attach the Wall-Mount

Attachment (supplied with the
TV or LCD Display) to the rear of
the TV or LCD Display (to make
it parallel with the wall).

4 Attach the

LCD Display using

M6

WM2

to the TV or

WM2

M6

.

1.5 N·m
{15 kgf·cm}

VS

− 18 (US) −

5 Detach the Table-Top Stand

from the TV or LCD Display.

Remove one side of the Table-Top Stand



at a time. Firmly hold the Table-Top
Stand securely with both hands while
the other people lift up the TV or LCD
Display.

Installing the TV or LCD
Display on the wall

1

US

Repeat the previous step and remove



the other side of the Table-Top Stand.

Note

Three or more people are required to detach the



Table-Top Stand.
Be careful not to use excessive force while detaching



the Table-Top Stand from the TV or LCD Display as it
may cause the TV or LCD Display set to fall resulting
in personal injury or physical damage to the TV or
LCD Display.
Take care when handling the Table-Top Stand to



prevent damage to the TV or LCD Display.
Be careful when lifting the TV or LCD Display as the



Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
Take care when removing the Table-Top Stand from



the TV or LCD Display to prevent it from falling over
and damaging the surface that the TV or LCD Display
is sitting on.
Be sure to store the removed screws and unused



parts in a safe place, keeping them away from
children.

2

− 19 (US) −

3 Screw the left and right side of

the Wall-Mount Bracket.

4

M6

5 When moving the TV or LCD

Display, hold it firmly from the
bottom.

6

M6

− 20 (US) −