Sony VPL-EX295, VPL-EX290, VPL-EX255, VPL-EX250, VPL-EX235 User Manual

...

Data Projector

4-540-680-12 (1)

Operating Instructions

Before operating the unit, please read this manual and supplied Quick Reference Manual thoroughly and retain it for future reference.

VPL-EW295/EW255/EW235 VPL-EX295/EX290/EX255/EX250/EX235/EX230

Not all models are available in all countries and area. Please check with your local Sony Authorized Dealer.

Table of Contents

Overview

Location and Function of Controls .... 4

Main Unit .....................................4

Connector Panel ...........................5

Remote Commander and Control

Panel Keys .................................6

Preparation

Connecting the Projector ................... 9

Connecting a Computer ................9

Connecting a Video

equipment ................................ 11

Connecting a microphone .......... 13

Connecting a USB memory

device ......................................13

Connecting an External Monitor and

Audio Equipment .................... 14

Projecting/Adjusting an Image

The Information Menu .....................31

Network

Using Network Features ...................32

Displaying the Control Window of

the Projector with a Web

Browser ...................................32

Confirming the Information

regarding the Projector ............33

Operating the Projector from a

Computer .................................34

Using the e-mail report

Function ...................................34

Setting the LAN Network of the

projector ..................................35

Setting the WLAN Network of the

projector ..................................35

Setting the Custom Labels for the

Input Connectors of the

Projector ..................................38

Setting the Control Protocol of the

Projector ..................................38

Projecting an Image .........................15

Adjusting the Projected image ... 16

Turning Off the Power ................19

Adjustments and Settings Using a Menu

Using a MENU ................................20

The Picture Menu .............................21

The Screen Menu ............................. 22

The Function Menu .......................... 26

The Operation Menu ........................ 27

The Connection/Power Menu ..........28

The Installation Menu ...................... 30

Table of Contents

Presentation Function via Network

Using Presentation Function via

Network .........................................42

Installing Projector Station for

Network Presentation ..............42

Starting Projector Station for

Network Presentation ..............42

Projecting an Image ....................43

Connection Settings ....................43

Using the Controller ...................44

Displaying Images or Files Sent

from a Tablet PC/

Smartphone .............................44

Playing Video and Audio using USB Connection

Playing Video and Audio using USB

Connection ....................................46

Starting USB Display .................46

Playing Video and Audio ...........46

Using the Controller ................... 46

USB Media Viewer

Using USB Media Viewer ................48

Thumbnail Mode ........................49

Option Menu ...............................49

Display Mode .............................50

Option Menu ...............................50

Slideshow Mode .........................50

Option Menu ...............................51

Others

Indicators ..........................................52

Messages List ...................................53

Troubleshooting ...............................54

Replacing the Lamp .........................56

Cleaning the Air Filter .....................58

Specifications ...................................59

Projection Distance ..........................66

Dimensions .......................................80

END USER LICENSE

AGREEMENT ..............................86

Index .................................................92

Table of Contents

B Overview

Location and Function of Controls

Main Unit

5 4

7 8

qs qa

a Focus ring (page 16)

b Zoom ring (page 16)

c Lens

d Remote control detector

e ON/STANDBY indicator

(page 52)

f LAMP/COVER indicator

(page 52)

g Front feet (adjustable) (page 17)

7 8

Caution

Do not place anything near the ventilation holes as this may cause internal heat buildup. Do not place your hand near the ventilation holes and the circumference as this may cause injury.

l Speaker (VPL-EW295/EW255/

EW235/EX295/EX255/EX235 only)

m Connector panel (page 5)

n Security bar

Connects to a commercially available security chain or wire.

o Security lock

Connects to an optional security cable manufactured by Kensington. For details, visit Kensington’s web site. http://www.kensington.com/

p Control panel keys (page 6)

h Foot adjust button (page 17)

i Air filter cover/Ventilation holes

(intake) (page 58)

j Lamp cover (page 56)

k Ventilation holes (exhaust)

Location and Function of Controls

Connector Panel

VPL-EW295/EW255/EW235/EX295/EX255/EX235

4 5 6

VPL-EX290/EX250/EX230

6 7

Input (pages 9, 11)

a INPUT A

Video: RGB/YPBPR input connector

(RGB/YP

Audio: Audio input connector (AUDIO)

b INPUT B

Video: RGB input connector (RGB) Audio: Audio input connector (AUDIO)

c INPUT C

Video: HDMI input connector (HDMI) Audio: HDMI input connector (HDMI)

d S VIDEO (S VIDEO IN)

Video: S video input connector (S

VIDEO IN)

Audio: Audio input connector (L

(MONO) AUDIO/R)

BPR)

8q;3

e VIDEO (VIDEO IN)

Notes

• The audio inputs of S VIDEO and VIDEO

• The audio input connector and audio output

Output (page 14)

f OUTPUT

8q;3qa

Video: Video input connector (VIDEO) Audio: Audio input connector (L

(MONO) AUDIO/R)

are shared.

from the HDMI connector are available only on VPL-EW295/EW255/EW235/EX295/ EX255/EX235.

Video: Monitor output connector

(MONITOR)

Audio: Audio output connector

(AUDIO)

Overview

Location and Function of Controls

Notes

• This connector outputs the projected image or audio only when INPUT A or INPUT B is used.

• The audio output connector is available only on VPL-EW295/EW255/EW235/EX295/ EX255/EX235.

h LAN connector (page 32)

i AC IN (∼) socket

Connects the supplied AC power cord.

j USB connector (Type A) ( )

(pages 13, 48)

k USB connector (Type B) ( )

Others

g RS-232C connector (RS-232C)

RS-232C compatible control connector. Connects the computer’s RS-232C connector and th e RS-232C cross cables.

(page 46)

l Microphone input ( )

Note

Microphone input is available only on VPLEW295/EW255/EW235/EX295/EX255/ EX235.

Remote Commander and Control Panel Keys

Remote Commander

INPUT

APA ECO MODE

Control Panel Keys

RETURN

ASPECT

D ZOOM

ENTER

KEYSTONE

VOLUME

PATTERN

FREEZE

RESET

BLANK

MUTING

1 6

a Turning on the power/Going to

standby mode

?/1 (On/Standby) key

b Selecting an input signal

(page 15)

INPUT key

c Operating a menu (page 20)

MENU key RESET key ENTER /V/v/B/b (arrow) keys RETURN key

d Adjusting the image (page 16)

ASPECT key (page 22) KEYSTONE key (page 18) PATTERN key (page 18) APA (Auto Pixel Alignment) key

(page 18)

Note

Use this key when inputting a computer

signal via the RGB input connector (INPUT A or INPUT B).

Location and Function of Controls

e Using various functions during

projecting

D ZOOM (Digital Zoom) +/– key

Enlarges a portion of the image while projecting.

1 Press the D ZOOM + key to display

the digital zoom icon on the projected image.

2 Press the V/v/B/b keys to move the

digital zoom icon to the point on the image you want to enlarge.

3 Press the D ZOOM + key or the D

ZOOM – key repeatedly to change the enlargement ratio. The image can be

enlarged up to 4 times. Press the RESET key to restore the previous image.

BLANK key

Cuts off the projected image temporarily. Press again to restore the previous image. Picture muting helps reduce power consumption.

MUTING key (VPL-EW295/EW255/ EW235/EX295/EX255/EX235 only)

Mutes the audio output temporarily. Press again to restore the previous volume.

VOLUME +/– key (VPL-EW295/ EW255/EW235/EX295/EX255/ EX235 only)

Adjusts the volume output.

FREEZE key

Pauses a projected image. Press again to restore the image.

Notes

*1: Use this key when inputting a

computer signal. But it may not be used depending on the resolution of the input signal.

*2: Use this key when inputting a

computer signal.You cannot use this key when USB

“Type A USB”, “Type B

” or “Network” is selected as the

input.

f Setting the energy–saving mode

easily

ECO MODE key

Energy-saving mode can be set easily. Energy-saving mode consists of “Lamp Mode,” “With No Input,” “With Static Signal” and “Standby Mode.”

1 Press the ECO MODE key to display

the ECO Mode menu.

ECO Mode

ECO

User

RETURN

:Sel

:Back

2 Press the V/v key or ECO MODE key

to select “ECO” or “User” mode. ECO: Sets each mode to the optimum

energy-saving value. Lamp Mode: Low With No Input: Standby With Static Signal: Lamp Dimming Standby Mode: Low

User: Sets each item of the ECO

Mode menu as you desire (go to step 3).

3 Select “User” then press the b key.

The setting items appear.

User

Lamp Mode High

Constant Brightness Auto Power Saving

With No Input With Static Signal

Standby Mode

:S el

:S et

Off Lamp Dimming Standard

RETURN

:Back

4 Press the V/v key to select the item

then press the ENTER key.

5 Press the V/v key to select the setting

value.

6 Press the ENTER key.

The screen returns to the User screen. For details on ECO Mode settings, see “Lamp Mode,” “With No Input,” “With Static Signal” and “Standby Mode” on the Connection/Power menu (page 28).

Overview

Location and Function of Controls

Others

g Infrared transmitter

About remote commander operation

• Direct the remote commander toward the remote control detector.

• The shorter the distance between the remote commander and the projector is, the wider the angle within which the remote commander can control the projector becomes.

• Make sure that nothing obstructs the infrared beam between the remote commander and the remote control detector on the projector.

Location and Function of Controls

B Preparation

Connecting the Projector

Notes

• Make sure all the equipment is powered off when connecting the projector.

• Use the proper cables for each connection.

• Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or cause a malfunction. When pulling out a cable, be sure to grip it by the plug, not the cable itself.

• For more information, refer also to the instruction manuals of the equipment you are connecting.

• Use a no-resistance audio cable.

Connecting a Computer

Connection with a computer is explained for each input signal.

INPUT A/INPUT B

For connecting a computer with an RGB output connector.

Mini D-sub 15-pin cable (supplied)

RGB output

connector

Audio output

Computer

connector

Preparation

Audio cable (Stereo mini plug) (not supplied)

Notes

• The audio input connector is available only on VPL-EW295/EW255/EW235/EX295/EX255/ EX235.

• It is recommended that you set the resolution of your computer to 1280 × 800 pixels (VPL-EW295/ EW255/EW235) or 1024 × 768 pixels (VPL-EX295/EX290/EX255/EX250/EX235/EX230) for the external monitor.

INPUT C

For connecting a computer with an HDMI output connector.

HDMI cable (not supplied)

HDMI output

connector

Computer

Connecting the Projector

Notes

• Audio output from the HDMI connector is available only on VPL-EW295/EW255/EW235/ EX295/EX255/EX235.

• Use HDMI-compatible equipment which has the HDMI Logo.

• Use a high speed HDMI cable(s) on which the cable type logo is specified. (Sony products are recommended.)

• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal or CEC (Consumer Electronics Control) Signal.

USB connector (Type B) ( )

For connecting to a computer with a USB connector (“Projecting an Image using USB Connection” (page 46)).

USB connector

(Type A)

Computer

USB A-B cable (not supplied)

LAN connector

For connecting to a computer, tablet PC, or smartphone via a hub or router (“Presentation Function via Network” (page 42)).

LAN

connector

LAN cable (straight type)

Computer

Wired connection

Tablet PC/Smartphone

Computer

Wireless connection

Hub, router (wireless), etc.

(not supplied)

Connecting the Projector

USB connector (Type A) ( )

For connecting a USB wireless LAN module IFU-WLM3 (not supplied) (“Presentation Function via Network” (page 42)).

Wireless router, access point

USB wireless LAN module

Tablet PC/Smartphone

Computer

Notes

IFU-WLM3 (not supplied)

• Undesignated USB wireless LAN modules do not work.

• When connecting/disconnecting the USB wireless LAN module, make sure that the projector is in Standby mode (Standby Mode: “Low”), or the AC power cord is unplugged from the wall outlet.

• When wirelessly connecting a tablet PC/smartphone to the projector via USB wireless LAN Module IFU-WLM3 (not supplied), set “WLAN Network” to “Access Pt. (Manual)” in the projector’s “WLAN Settings” (page 28).

• For connecting to the access point, access to the Web browser, and input the settings for the access point to connect. For details, see “Setting the WLAN Network of the projector” (page 35).

Preparation

Connecting a Video equipment

Connections with a VHS video deck, DVD player, or BD player are explained for each input signal.

S VIDEO IN

For connecting video equipment with an S-video output connector.

S video cable (not supplied)

S video output

connector

Audio output

Computer

Note

The audio input connector is available only on VPL-EW295/EW255/EW235/EX295/EX255/ EX235.

connector

Audio cable (Phono plug × 2) (not supplied)

Connecting the Projector

VIDEO IN

For connecting video equipment with a video output connector.

Video cable (not supplied)

Video output

connector

Audio output

Video equipment

Note

connector

Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)

The audio input connector is available only on VPL-EW295/EW255/EW235/EX295/EX255/ EX235.

INPUT A

For connecting video equipment with a YPBPR output connector.

Component – Mini D-sub 15-pin cable (not supplied)

BPR output

connector

Audio output

Video equipment

connector

Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)

Note

The audio input connector is available only on VPL-EW295/EW255/EW235/EX295/EX255/ EX235.

Connecting the Projector

INPUT C

For connecting video equipment with an HDMI output connector.

HDMI cable (not supplied)

HDMI output

connector

Video equipment

Notes

• Audio output from the HDMI connector is available only on VPL-EW295/EW255/EW235/ EX295/EX255/EX235.

• Use HDMI-compatible equipment which has the HDMI Logo.

• Use a high speed HDMI cable(s) on which the cable type logo is specified. (Sony products are recommended.)

• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal or CEC (Consumer Electronics Control) Signal.

Connecting a microphone

Microphone ( )

For connecting a microphone.

Preparation

Microphone (not supplied)

Notes

• The microphone input is available only on VPL-EW295/EW255/EW235/EX295/EX255/EX235.

• Only dynamic microphones are supported.

Connecting a USB memory device

USB connector (Type A) ( )

For connecting a USB memory device (“Using USB Media Viewer” (page 48)).

USB memory device (not supplied)

Connecting the Projector

Connecting an External Monitor and Audio Equipment

OUTPUT

Projected images or input audio can be output to display equipment such as a monitor or audio equipment such as speakers with a built-in amplifier.

Audio equipment

Audio input

connector

Audio cable (stereo mini plug) (not supplied)

Display equipment

Notes

RGB input

connector

Mini D-sub 15-pin cable (supplied)

• The audio input connector is available only on VPL-EW295/EW255/EW235/EX295/EX255/ EX235.

• Projected images and audio can be output.

Connecting the Projector

B Projecting/Adjusting an Image

Projecting an Image

The size of a projected image depends on the distance between the projector and screen. Install the projector so that the projected image fits the screen size. For details on projection distances and projected image sizes, see

“Projection Distance” (page 66).

Projector

1 Plug the AC power cord into the wall

outlet.

2 Connect all equipment to the projector

(page 9).

3 Press the ?/1 key to turn on the unit.

4 Turn on the connected equipment.

5 Select the input source.

Press the INPUT key on the projector to display the menu for switching input signal on the screen. Press the INPUT key repeatedly, or press the select an image to be projected.

V/v key to

Video equipment

Wall outlet

Computer

6 When projecting a computer image,

switch your computer’s output to external display.

The method to switch the output varies depending on the type of computer.

(Example)

To project image files stored in a USB memory device, see “USB Media Viewer” (page 48). To play video and audio using USB Connection, see “Playing Video and Audio using USB Connection” (page 46). To use Presentation Function via Network, see “Presentation Function via Network” (page 42).

Projecting/Adjusting an Image

Projecting an Image

7 Adjust the focus, size and position of

the projected image (page 16).

Adjusting the Projected image

Focus Size (Zoom) Position

Focus ring

Zoom ring

Foot adjust button

Front feet (adjustable)

Projecting an Image

Adjusting the tilt of the projector with the front feet (adjustable)

By changing the tilt of the projector with the foot adjust buttons/front feet (adjustable), you can adjust the position of the projected image.

How to adjust the angle

1 Press and hold the foot adjust buttons.

2 Lift up the front of the projector to

adjust the angle.

3 Release the foot adjust buttons.

4 Turn the front feet (adjustable) to set

the angle of the projector precisely.

Notes

• Be careful not to let the projector down on your fingers.

• Do not push hard on the top of the projector with the front feet (adjustable) extended.

Changing the aspect ratio of the projected image

Press the ASPECT key on the remote commander to change the aspect ratio of the projected image. You can also change the setting in Aspect of the Screen menu (pages 22, 24).

Projecting/Adjusting an Image

Projecting an Image

Correcting trapezoidal distortion of the projected image (Keystone feature)

Normally the Keystone feature automatically adjusts the projected image. The Keystone feature may not work automatically if the screen is tilted. In this case, set Keystone manually.

1 Press the KEYSTONE key on the remote

commander or select V Keystone in the Installation menu.

2 Use the V/v/B/b keys to set the value. The

higher the value, narrower the top of the projected image. The lower the value, the narrower the bottom.

Note

Since the Keystone adjustment is an electronic correction, the image may be deteriorated.

Increase the number towards plus

Increase the number towards minus

Displaying a pattern

You can display a pattern for adjusting the projected image or a grid pattern with the PATTERN key on the remote commander. Press the PATTERN key again to restore the previous image. You can use a grid pattern as a guide to write text or to draw lines and shapes on the whiteboard or blackboard without using a computer.

Note

You cannot use this key when “Type A USB”, “Type B USB” or “Network” is selected as the input.

Automatically adjusts Phase, Pitch and Shift of projected image while a signal is input from a computer (APA (Auto Pixel Alignment))

Press the APA key on the remote commander. Press again to cancel adjusting during the setting. You can also set APA in the Screen Menu (page 23). If Smart APA in the Function menu is set to “On”, executes APA automatically when a signal is input (page 26).

Projecting an Image

Turning Off the Power

1 Press the ?/1 key on the unit or the remote commander.

The projector starts shutdown and turns off. If you press the ?/1 key within 10 seconds again, shutdown is cancelled.

Note

Do not turn off the projector soon after the lamp lights. It may cause a malfunction of the lamp (does not light ,etc.).

2 Unplug the AC power cord from the wall outlet.

To turn off without displaying confirmation message

Press and hold the ?/1 key on the unit for a few seconds (page 53).

ECO gauge

This gauge indicates the current effectiveness of the projector’s ECO function. (For details on the ECO function, see “ECO MODE key” (page 7) and “ECO” (page 28).) The leaf icons are displayed when the projector is shut down. The number of displayed icons varies according to how much energy is saved as a result of using the ECO function.

ECO gauge

Projecting/Adjusting an Image

Projecting an Image

B Adjustments and Settings Using a Menu

Using a MENU

Note

The menu displays used for the explanation below may be different depending on the model you are using.

1 Press the MENU key to display the

menu.

2 Select the setting menu.

Use the V/v key to select the setting menu then press the b key or ENTER

key.

Setting menu

Picture

Picture Mode Standard Reset Contrast Brightness Color Hue Color Temp. Sharpness Expert Setting

:Sel :Set :Back

Low

3 Select the setting item.

Use the V/v key to select the setting menu then press the b key or ENTER

key.

To return to the selection screen of the setting menu, press the B or RETURN key.

Setting items

Picture

Picture Mode Standard

Reset Contrast Brightness Color Hue Color Temp. Sharpness Expert Setting

80 50 50 50

Low

operations in step 3 and then press the ENTER key to register the setting. To return to the selection screen of the setting items, press the B or RETURN key. You can press the RESET key to reset an item to its factory setting value to aid setting.

Using a pop-up menu

Press the V/v/B/b key to select an item. A selected item takes effect immediately, except “Language”, which will take effect after you press the ENTER key.

Picture Mode

Dynamic

Sta ndard

Presentation Blackbo ard Game Cinema

:Back

RETURN

:Sel

Using the setting menu

Press the V/v key to select the item. Press the ENTER key to register the setting and return to the previous screen.

Using the adjustment menu

To increase the value, press the V/b key and to decrease the number, press the v/B key. Press the ENTER key to register the setting and return to the previous screen.

Contrast

:Sel :Set :Back

4 Make the setting or adjustment for the

selected item.

The setting method varies, depending on the setting item. If the next menu window is displayed, select the item according to the

Using a MENU

Adjust

Back

5 Press the MENU key to clear the

menu.

The menu disappears automatically if no operation is performed.

The Picture Menu

The Picture is used to adjust the picture for each input signal.

Items Item descriptions

Picture Mode Dynamic: Emphasizes the contrast to produce a dynamic and vivid picture.

Reset

Contrast The higher the value, the greater the contrast. The lower the value, the lower

Brightness The higher the value, the brighter the picture. The lower the value, the darker

*3 *4

Color

*3 *4 *5

Hue

Color Temp.

Sharpness

Expert Setting

Gamma

*1 *8

Mode

Standard: Provides an image which is natural and well balanced. Presentation

: Provides a bright image, suitable for presentations. Blackboard: Provides an image suitable for displaying on a blackboard. Game: Provides an image suitable for viewing games. Cinema: Provides an image suitable for viewing movies.

Resets the factory setting.

the contrast.

the picture.

The higher the value, the greater the intensity. The lower the value, the lower the intensity.

The higher the value, the more greenish the picture becomes. The lower the value, the more reddish the picture becomes.

High/Middle/Low: The higher the value, the more bluish the picture. The lower the value, the more reddish the picture.

The higher the value, the sharper the picture. The lower the value, the softer the picture.

Graphics1: Gamma correction to make halftones brighter. This setting is suitable when projecting highly colorful images, such as photos, in a bright place. Graphics2: Gamma correction to improve the reproduction of halftones. Highly colorful images, such as photos, can be reproduced in natural tones. Tex t: Improves black and white contrast. Suitable for images with lots of text content.

Adjustments and Settings Using a Menu

Notes

*1: When a computer signal is input, this option is available. *2: The settings in the Picture return to their factory defaults, except for Picture Mode. *3: When a video signal is input, this option is available. *4: When the signal without color burst signal is input after selecting “Video” or “S-Video”, this

option is unavailable. *5: When an analog TV signal is input, this option may not available, depending on the color system. *6: When “Picture Mode” is set to the item other than “Presentation” or “Blackboard,” this option

is available. *7: Not available if “Input” is set to “Type A USB.” *8: When “Picture Mode” is set to “Blackboard,” this option is unavailable.

The Picture Menu

The Screen Menu

The Screen menu is used to adjust the size, position and aspect ratio of the projected image for each input signal.

Items Item descriptions

Aspect

VPL-EW295/EW255/ EW235: When the computer signal is input

VPL-EW295/EW255/ EW235: When the video signal is input

VPL-EX295/EX290/ EX255/EX250/ EX235/EX230: When the computer signal is input

VPL-EX295/EX290/ EX255/EX250/ EX235/EX230: When the video signal is input

Changes the aspect ratio of the projected image (page 24).

4:3: Displays the image to fit the maximum projected image size with an aspect ratio fixed to 4:3. 16:9: Displays the image to fit the maximum projected image size with an aspect ratio fixed to 16:9. Full 1: Displays the image to fit the maximum projected image size without changing the aspect ratio of the input signal. Full 2: Displays the image to fit the maximum projected image size changing the aspect ratio of the input signal. Full 3: Displays the image to fit the maximum width or height, up to 1280 × 720 pixels, without changing the aspect ratio of the input signal. Normal: Displays the image on the center position of the projected screen without changing the resolution of the input signal or enlarging the image.

Zoom: Zooms the center area of a projected image.

4:3: Displays the image to fit the maximum projected image size

with an aspect ratio fixed to 4:3. 16:9: Displays the image to fit the maximum projected image size with an aspect ratio fixed to 16:9. Full 1: Displays the image to fit the maximum projected image size without changing the aspect ratio of the input signal. Normal: Displays the image on the center position of the projected screen without changing the resolution of the input signal or enlarging the image.

The Screen Menu

Items Item descriptions

Adjust Signal Adjusts the image of computer signal. Use this item if the edge of

the image is cut and reception is bad.

APA

*2 *3

Automatically adjusts the projected image to an optimum quality when you press the ENTER key (page 6).

Phase

Adjusts the dot phase of the display pixel and the input signal. Set to the value where looks clearest.

*2 *5

Pitch

The higher the value, the wider the horizontal image elements (pitch). The lower the value, the narrower the horizontal image elements (pitch).

Shift

H (Horizontal): The higher the value, the farther right the image is projected on the screen. The lower the value, the image farther left. V (Vertical): The higher the value, the farther up the image is projected on the screen. The lower the value, the image farther down.

Notes

*1: • Note that if the projector is used for profit or for public viewing, modifying the original picture

by switching to the aspect mode may constitute an infringement of the rights of authors or producers, which are legally protected.

• Depending on the input signal, setting items for aspect ratio or some other setting items cannot be set in some cases, or changing the aspect ratio setting may have no effect.

• A part of the image may be displayed in black, depending on the setting item.

*2: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B). *3: If the projected image includes large amount of black portion around it, the APA function will

not work properly and a part of the image may not be displayed on the screen and also optimum image cannot be obtained, depending on the type of input signal. In this case, adjust the “Phase,” “Pitch,” and “Shift” items manually.

*4: Available when a computer or a video signal is input from the RGB/YP

BPR input connector

(INPUT A).

*5: When “APA” (page 23) or “Smart APA” (page 26) is performed, the adjusted value for “Pitch”

will return to its factory default. If you want to continue using the adjusted value, set “Smart APA” to “Off.”

Adjustments and Settings Using a Menu

The Screen Menu

Aspect

VPL-EW295/EW255/EW235

Input signal Recommended

setting value and

projected image

4:3 Full1

16:9 Full1

Computer signal

16:10 Full1

4:3 4:3

16:9 16:9

Video signal

*1 *2 *3

*4 *5

*1: If you select “Normal,” the image is

projected in the same resolution as the input signal without changing the aspect ratio of the original image.

*2: If you select “Full2,” the image is projected

to fit the projected image size, regardless of the aspect ratio of the image.

*3: If you adjust the projected image position

using an image with 16:9 aspect ratio and then switch the input source to 4:3 image, the top and bottom edge of the image may be hidden. In this a case, select “Full3.”

*4: Depending on the input signal, the

projected image may be projected as illustrated below. In this a case, select “16:9.”

The Screen Menu

*5: Depending on the input signal, the image

may be projected as illustrated below. In this a case, select “Zoom.”

VPL-EX295/EX290/EX255/EX250/ EX235/EX230

Input signal Recommended

setting value and

projected image

4:3

16:9

Full1

Computer signal

16:10 Full1

*1 *2

*1: If you select “Normal,” the image is

projected in the same resolution as the input signal without changing the aspect ratio of the original image.

*2: If you select “4:3,” the image is projected

to fit the projected image size, regardless of the aspect ratio of the image.

*3: Depending on the input signal, the

projected image may be projected as illustrated below. In this a case, select “16:9.”

Adjustments and Settings Using a Menu

4:3 4:3*3

*4: Depending on the input signal, the

projected image may be projected as illustrated below. In this a case, select “Zoom.”

16:9 16:9

Video signal

The Screen Menu

The Function Menu

The Function menu is used for setting various functions of the projector.

Items Item descriptions

Vo l u m e

Mic Volume

Speaker

Smart APA On/Off: When set to “On,” APA functions automatically when a

CC Display CC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed

Lamp Timer Reset When replacing the lamp, resets the lamp timer (page 56).

Start Up Image On/Off: When set to “On,” the Start Up Image is displayed on the

Notes

*1: APA functions when a computer signal is input via the RGB input connector (INPUT A/INPUT

B). *2: The maximum available mic volume is set by the value of “Volume.” *3: VPL-EW295/EW255/EW235/EX295/EX255/EX235 only.

The higher the value, the louder an audio volume and the lower the value, the lower the audio volume.

Adjust the volume of the microphone.

On/Off: When set to “On,” speaker outputs sound. To not output sound from the speaker, select “Off.”

signal is input.

caption service (captions or text). Off: Closed caption does not appear.

screen when the projector is powered on.

The Function Menu

The Operation Menu

The Operation menu is used for setting for the operations by using the menu or the remote commander.

Items Item descriptions

Language Selects the language used in the menu and messages.

Status On: All on-screen statuses are enabled.

Security Lock

Control Key Lock

Off: Turns off the on-screen displays, except for menus, warning messages and messages from the message list.

On/Off: This function enables restriction of the projector to authorized users by password. The setting procedures for security locking are as follows:

1 Select “On” and press the ENTER key to display the setting menu. 2 Input the password with the MENU, V/v/B/b and ENTER keys. (The

default setting password is “ENTER, ENTER, ENTER, ENTER.”)

3 Input a new password with the MENU, V/v/B/b and ENTER keys. 4 Enter the password again to confirm.

Enter the password when you turn on the projector after disconnecting and reconnecting the AC power cord. When it is set to “Off,” you can cancel the security lock. You are required to input the password again. If you fail to enter the correct password after three consecutive times, the projector cannot be used. In this case, press the ?/1 key to go Standby mode then turn on the power again.

On/Off: When set to “On,” locks all the control panel keys of the projector. However, you can operate the following when set to “On”:

• Press and hold the ?/1 key for approximately 10 seconds during Standby

mode. c The projector turns on.

• Press and hold the MENU key for approximately 10 seconds during power on. c “Control Key Lock” is set to “Off” and enables operation of all keys on

the projector.

Adjustments and Settings Using a Menu

Note

*1: You will not be able to use the projector if you forget your password. If you call qualified Sony

personnel because you have forgotten the password, you will be asked to verify the projector’s serial number and your identity. (This process may differ in other countries/regions.) Once your identity has been confirmed, we will provide you with the password.

The Operation Menu

The Connection/Power Menu

The Connection/Power menu is used for setting for the connections and power.

Items Item descriptions

LAN Settings

IP Address

Setup

WLAN Settings

*10

WLAN Connection

WLAN

*14

Network

Input-A Signal Sel.

ECO

Lamp Mode High/Standard/Low/Auto

Constant Brightness

Auto Power Saving

With No Input Lamp Cutoff: The lamp turns off automatically and power

With Static Signal

Standby Mode*

Auto (DHCP): The IP address is assigned automatically from the DHCP server such as a router.

Manual: To specify the IP Address manually.

On/Off: Set the wireless output of the USB wireless LAN module (not

supplied) to On/Off.

Access Pt. (Auto)/Access Pt. (Manual)/Client

*12

WLAN.

Auto/Computer/Video GBR/Component:

*11

: Changes modes for

When set to “Auto,” selects

the type of video signal input automatically when “Input-A” is selected.

*5 *7

: When set to “High,” the image becomes brighter, and power consumption becomes higher. When set to “Low,” power consumption is minimized; however, the image will be darker. When set to “Auto,” brightness is adjusted automatically according to image content. Dark images are projected with brightness adjusted, leading to energy-saving. Bright images are projected brightly, without adjusting brightness.

On/Off: Available when the lamp mode is set to High. Outputs light at a certain brightness.

*13

consumption is reduced if no signal is input for more than 10 minutes. The lamp lights again when a signal is input or any key is pressed. In Lamp Cutoff, the ON/STANDBY indicator lights in orange. (page 52) Standby*

: If no signal is input to the unit for more than 10 minutes,

the power turns off automatically, and the unit enters standby mode.

Off: You can deactivate the With No Input.

Lamp Dimming

seconds, lamp output is gradually reduced (approximately 10% to

15%*

) from that set in the Lamp Mode. Automatically the lamp slowly

*4 *5 *7

: If an image does not change for about 10

darkens to approximately 30% of its lamp output according to the selected time (with no change to input signal) “5,” “10,” “ 15,” “20” minutes or “Demo.,” While dimming the lamp, the message “Lamp Dimming” appears. If you select “Demo.,” the image will start to darken about 40 seconds later. When any change in signal is detected, or an operation (remote control or control panel) is performed, normal brightness is restored. Off: You can deactivate the With Static Signal.

Standard/Low: When set to “Low,” lowers power consumption in Standby mode.

The Connection/Power Menu

Items Item descriptions

Direct Power On On/Off: When set to “On,” you can turn the power on without going to

Standby mode when the AC power cord is connected to a wall outlet. With the projector turned off, you can also unplug the AC power cord without going to Standby mode, regardless of the Direct Power On setting.

Notes

*1: This may not be optimum depending on the input signal. In this case set manually according

to the connected equipment.

*2: When “Standby Mode” is set to “Low,” the network and network control function cannot be

operated while the projector is in standby mode. *3: This varies depending on the “Lamp Mode” setting. *4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only

notice that the lamp has dimmed when its brightness is restored after there is a change in input

signal. *5: This mode does not work for about three minutes after the lamp lights. A change in signal may

not be detected depending on the input image. The lamp may become brighter at intervals

during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes

priority. *6: Select “Off” to avoid entering standby mode when there is no input signal. *7: Does not function when “Type A USB”, “Type B USB” or “Network” is selected as the input.

In this case, it becomes equivalent to “Standard.” *8: Reflecting changes in WLAN settings may take a few moments. *9: To set the IP address manually, select “Manual”, press “Apply”, then enter the IP address. *10: When you send images or files from a tablet PC/smartphone and display them (page 44), set

“WLAN Network” to “Access Pt. (Auto)” or “Access Pt. (Manual),” to use USB wireless LAN

module IFU-WLM3 (not supplied) as a wireless access point. *11: The factory default settings for “Access Pt. (Manual)” are as follows.

SSID: VPL + MAC address for LAN

Security Method: WEP(64bit)

Password: sony1

To change the settings for “Access Pt. (Manual)”, use a Web browser.

For details, see “Setting the WLAN Network of the projector” (page 35).

If “Access Pt. (Manual)” is set, when you use Presentation Function via Network (page 42),

select “Manual Connect” to connect to the network. *12: For changing the settings for “Client,” use the Web browser for change. For details, see

“Setting the WLAN Network of the projector” (page 35). *13: Constant Brightness mode will be enabled for about 2,000 hours after it is activated at early

usage. After this period, it will be disabled automatically. Activated time and brightness may

vary depending on the usage conditions. *14: If the projector cannot connect wirelessly, click [Apply] once again to make sure the

connection is established. For details, see “Setting the WLAN Network of the projector”

(page 35).

Adjustments and Settings Using a Menu

The Connection/Power Menu

+ 65 hidden pages