Sony UWP-C1-C2, UWP-X1-X2, UWP-S1-S2 User Manual
2-347-711-32(2)
Wireless
Microphone Package
Operating Instructions
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
UWP-C1/C2
UWP-S1/S2
UWP-X1/X2
2003 Sony Corporation
2
Table of Contents
Configuration of the
Packages ............................. 4
UWP-C1..................................... 4
UWP-C2..................................... 5
UWP-S1 ..................................... 6
UWP-S2 ..................................... 7
UWP-X1 .................................... 8
UWP-X2 .................................... 9
Features .................................. 10
Precautions............................. 12
Parts Identification ................. 13
Body-pack transmitter
(UTX-B1)................................. 13
Hand-held microphone
(UTX-H1) ................................ 14
Portable diversity tuner
(URX-P1) ................................. 15
Half-rack size diversity tuner
(URX-R1) ................................ 17
Diversity tuner module
(URX-M1) ............................... 18
Power Supply ......................... 20
Inserting the batteries ............... 20
Attachment and Installation
Procedures ........................ 23
Attaching the supplied
accessories to the body-pack
transmitter (UTX-B1) .............. 23
Attaching the supplied accessory
to the hand-held microphone
(UTX-H1) ................................ 24
Attaching the supplied accessories
to the portable diversity tuner
(URX-P1) ................................. 24
Installing the diversity tuner
module (URX-M1) .................. 25
Settings ................................... 28
Setting the transmission
channel ..................................... 28
Setting the reception channel ... 29
Detecting and selecting the
available channels
automatically (diversity tuner
module (URX-M1) only) ......... 30
Setting the attenuation level
of the audio input ..................... 31
Resetting the accumulated
battery use time indication ....... 32
Setting the RF output level ...... 32
Setting the monitor level
(portable diversity tuner
(URX-P1) only) ....................... 33
Operation ................................ 34
System Configurations .......... 35
Error Messages ...................... 38
Troubleshooting ..................... 39
Specifications ......................... 41
Appendix ................................. 45
Wireless microphone system
frequency list............................ 45
AC adapter for use with the
URX-R1 ................................... 47
3
Configuration of the Packages
Configuration of the Packages
This operation manual is for the UWP-C1/C2/S1/S2/X1/X2
wireless microphone packages. The contents of each package
are described below.
UWP-C1
The UWP-C1 consists of a body-pack transmitter (UTX-B1)
and a portable diversity tuner (URX-P1). When used in
conjunction with a compact camcorder, the UWP-C1 makes a
mobile system for ENG (Electronic News Gathering) or EFP
(Electronic Field Production) purposes.
Body-pack transmitter
(UTX-B1) (1)
Supplied accessories
• Omni-directional lavalier microphone
(1)
• XLR-BMP conversion cable (for use
with the URX-P1 only) (1)
• Stereo mini plug-BMP conversion
cable (for use with the URX-P1 only)
(1)
Portable diversity tuner
(URX-P1) (1)
• Wind screen (1)
• Shoe mount adapter (1) • Belt clip (2)
• Operation manual (1)• Microphone stand adapter (1)
• Holder clip (1)
4
UWP-C2
The UWP-C2 consists of a hand-held microphone (UTX-H1)
and a portable diversity tuner (URX-P1). When used in
conjunction with a compact camcorder, the UWP-C2 makes a
mobile system for ENG (Electronic News Gathering) or EFP
(Electronic Field Production) purposes.
Hand-held microphone
(UTX-H1) (1)
Portable diversity tuner
(URX-P1) (1)
Supplied accessories
• Microphone holder (1) • Belt clip (1)
• Shoe mount adapter (1) • XLR-BMP conversion cable (for use
with the URX-P1 only) (1)
• Stereo mini plug-BMP conversion
cable (for use with the URX-P1
only) (1)
• Microphone stand adapter (1) • Operation manual (1)
5
Configuration of the Packages
UWP-S1
The UWP-S1 consists of a body-pack transmitter (UTX-B1)
and a half-rack size diversity tuner (URX-R1). The UWP-S1 is
suitable for constructing a wireless system for AV
presentations.
Body-pack transmitter
(UTX-B1) (1)
Supplied accessories
• Unidirectional lavalier
microphone (1)
• AC adapter (1) (See
page 47.)
Half-rack size diversity tuner
(URX-R1) (1)
• Wind screen (1) • Holder clip (1)
• Belt clip (1) • Operation manual (1)
6
UWP-S2
The UWP-S2 consists of a hand-held microphone (UTX-H1)
and a half-rack size diversity tuner (URX-R1). The UWP-S2 is
suitable for constructing a wireless system for AV
presentations.
Hand-held microphone
(UTX-H1) (1)
Supplied accessories
• Microphone holder (1) • AC adapter (1) (See page 47.)
• Operation manual (1)
Half-rack size diversity tuner
(URX-R1) (1)
7
Configuration of the Packages
UWP-X1
The UWP-X1 consists of a body-pack transmitter (UTX-B1)
and a diversity tuner module (URX-M1). By installing the tuner
module into a tuner base unit or a powered mixer, the system
construction to meet the desired purpose of use and required
system scale becomes possible.
Body-pack transmitter
(UTX-B1) (1)
Diversity tuner module
(URX-M1) (1)
Supplied accessories
• Unidirectional lavalier
microphone (1)
• Belt clip (1) • Operation manual (1)
• Wind screen (1) • Holder clip (1)
8
UWP-X2
The UWP-X2 consists of a hand-held microphone (UTX-H1)
and a diversity tuner module (URX-M1) . By installing the
tuner module into a tuner base unit or a powered mixer, the
system construction to meet the desired purpose of use and
required system scale becomes possible.
Hand-held microphone
(UTX-H1) (1)
Supplied accessories
• Microphone holder (1)
Diversity tuner module
(URX-M1) (1)
• Operation manual (1)
9
Features
Features
Each of the UWP-C1/C2/S1/S2/X1/
X2 wireless microphone packages
(referred to as the UWP series
hereafter) combines a transmitter
(body-pack transmitter (UTX-B1) or
hand-held microphone (UTX-H1)) and
a receiver (portable diversity tuner
(URX-P1), half-rack size diversity
tuner (URX-R1), or diversity tuner
module (URX-M1)). The UWP series
can be used with a compact camcorder
for ENG (Electronic News Gathering)
purposes, and with a powered mixer
for AV presentations or as a PA
(public address) system.
Note
The UWP series is not compatible
with conventional WRT series
transmitters, WRR series tuners, or
WRU series tuner units.
The features of each package are
described below.
UWP-C1
Body-pack transmitter (UTX-B1)
This is a small and lightweight
transmitter with a crystal-controlled
PLL (phase lock loop) synthesized
system and a BMP-type microphone
input connector. The RF power output
can be set at 10 mW or at 2 mW.
Portable diversity tuner
(URX-P1)
This tuner employs a space diversity
system with little signal dropout and
two angle-adjustable antennas. It
comes with an adapter for mounting
the tuner on the compact camcorder
(DSR-PDX10/PDX10P/PD150/
PD150P, etc.).
UWP-C2
Hand-held microphone (UTX-H1)
This microphone is equipped with a
built-in antenna and a unidirectional
dynamic microphone unit. The RF
power output can be set at 10 mW or
at 2 mW.
Portable diversity tuner
(URX-P1)
This tuner employs a space diversity
system with little signal dropout and
two angle-adjustable antennas. It
comes with an adapter for mounting
the tuner on the compact camcorder
(DSR-PDX10/PDX10P/PD150/
PD150P, etc.).
UWP-S1
Body-pack transmitter (UTX-B1)
This is a small and lightweight
transmitter with a crystal-controlled
PLL (phase lock loop) synthesized
system and a BMP-type microphone
input connector. The RF power output
can be set at 10 mW or at 2 mW.
10
Half-rack size diversity tuner
(URX-R1)
This tuner employs a space diversity
system with little signal dropout and
two angle-adjustable antennas. It
comes with two types of audio
connectors (1/4-inch jack and XLR
type) on the rear panel.
UWP-S2
Hand-held microphone (UTX-H1)
This microphone is equipped with a
built-in antenna and a unidirectional
dynamic microphone unit. The RF
power output can be set at 10 mW or
at 2 mW.
Half-rack size diversity tuner
(URX-R1)
This tuner employs a space diversity
system with little signal dropout and
two angle-adjustable antennas. It
comes with two types of audio
connectors (1/4-inch jack and XLR
type) on the rear panel.
UWP-X2
Hand-held microphone (UTX-H1)
This microphone is equipped with a
built-in antenna and a unidirectional
dynamic microphone unit. The RF
power output can be set at 10 mW or
at 2 mW.
Diversity tuner module
(URX-M1)
This tuner module can be incorporated
into the MB-806A Tuner Base Unit or
SRP-X700P Powered Mixer.
UWP-X1
Body-pack transmitter (UTX-B1)
This is a small and lightweight
transmitter with a crystal-controlled
PLL (phase lock loop) synthesized
system and a BMP-type microphone
input connector. The RF power output
can be set at 10 mW or at 2 mW.
Diversity tuner module
(URX-M1)
This tuner module can be incorporated
into the MB-806A Tuner Base Unit or
SRP-X700P Powered Mixer.
11
Precautions
Precautions
• The UWP series product must be
used within a temperature range of
0°C to 40°C (32°F to 104°F).
• Operating the UWP series product
near electrical equipment (motors,
transformers, or dimmers) may cause
it to be affected by electromagnetic
induction. Keep the UWP series
product as far from such equipment
as possible.
• The presence of the lighting
equipment may produce electrical
interference over the entire
frequency range. Position the UWP
series product so that interference is
minimized.
• To avoid degradation of the signalto-noise ratio, do not use the UWP
series product in noisy places or in
locations subject to vibration, such as
the following:
— near electrical equipment, such as
motors, transformers or dimmers
— near air conditioning equipment
or places subject to direct air
flow from an air conditioner
— near public address loudspeakers
— where adjacent equipment might
knock against the tuner
Keep the UWP series product as far
from such equipment as possible or
use buffering material.
• Clean the surface and the connectors
of the UWP series product with a
dry, soft cloth. Never use thinner,
benzene, alcohol or any other
chemicals, since these may mar the
finish.
To prevent electromagnetic
interference from portable
communication devices
The use of portable telephones and
other communication devices near
the UWP series product may result
in malfunction and interference with
audio signals. It is recommended
that portable communication
devices near the UWP series
product be turned off.
12
Parts Identification
Body-pack transmitter (UTX-B1)
1 Antenna
2 Audio input connector
Connect the supplied lavalier
microphone here.
A AF (audio frequency) indication
Appears whenever the input audio
signal is stronger than the reference
level.
B RF (antenna output) indication
Appears during signal transmission
from the antenna.
C RF (antenna output) level
indication
Shows the RF output level setting.
For details, see “Setting the RF output
level” on page 32.
D BATT (battery) indication
Shows the battery condition.
For details, see “Power Supply” on
page 20.
E CH (channel) indication
Shows the transmission channel. Each
time you press the SET button in
transmission mode, the channel
indication changes as follows.
For details, see “Settings” on page
28.
3 Power indicator
Lights up red when the transmitter is
tuned on.
4 Display section
C
D
B
A
AF RFCHBATT
E
H
L
Transmission
channel
Transmission
frequency
Attenuation
level of the
input signal
Accumulated
battery use
time
Press
the
SET
button.
13
Parts Identification
5 + (+ selection) / – (– selection/
reset) buttons
Press these buttons to set the
transmission channel, frequency, or
attenuation level of the input signal.
The “–” button resets the accumulated
battery use time to “00:00”.
6 Battery compartment
Accommodates two LR6 (size AA)
alkaline batteries.
For details on how to insert the
batteries, see “Power Supply” on
page 20.
7 SET button
Press to change and enter display
parameters.
For details, see “Settings” on page
28.
8 POWER switch
Turns the power of the transmitter ON
or OFF.
1 Power indicator
Lights up red when the microphone is
turned on.
2 POWER switch
Turns the power of the microphone
ON or OFF.
3 Battery compartment
Accommodates two LR6 (size AA)
alkaline batteries.
For details on how to insert the
batteries, see “Power Supply” on
page 20.
4 Display section
C
D
B
A
H
L
E
Hand-held microphone (UTX-H1)
The rear
side of the
battery
compartment
14
A AF (audio frequency) indication
Appears whenever the input audio
signal is stronger than the reference
level.
B RF (antenna output) indication
Appears during signal transmission
from the antenna.
C RF (antenna output) level
indication
Shows the RF output level setting.
For details, see “Setting the RF output
level” on page 32.
D BATT (battery) indication
Shows the battery condition.
For details, see “Power Supply” on
page 20.
E CH (channel) indication
Shows the transmission channel. Each
time you press the SET button, the
channel indication changes as follows.
For details, see “Settings” on page
28.
Transmission
channel
Portable diversity tuner (URX-P1)
Transmission
frequency
Attenuation
level of the
input signal
Accumulated
battery use
time
Press
the
SET
button.
1 Antennas a/b
The angle of the antennas can be
5 + (+ selection) / – (– selection/
reset) buttons
Press these buttons to set the
transmission channel, frequency, or
attenuation level of the input signal.
The “–” button resets the accumulated
battery use time to “00:00”.
6 SET button
Press to change display parameters.
For details, see “Settings” on page
28.
......................................................................................................................................................................
adjusted manually.
2 MONITOR connector (3.5-mm
diameter stereo mini jack)
To monitor the tuner output, connect
the headphones to this connector.
3 RF (radio frequency) indicator
Indicates the strength of the RF input
signal.
On in green: RF input is 15 dBµ*
or more.
Off: RF input is less than 15 dBµ*.
* 0 dBµ = 1 µVEMF
15
Loading...