This receiver incorporates Dolby* Digital and Pro Logic Surround
and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
SPECIFICATIONS
STR-DA3ES/DA5ES
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09 % total harmonic distortion from
250 milliwatts to rated output.
AMPLIFIER SECTION
POWER OUTPUT
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.05 %)
STR-DA5ES:110 W + 110 W
STR-DA3ES:100 W + 100 W
(4 ohms 20 Hz – 20 kHz, THD 0.09 %)
STR-DA5ES:90 W + 90 W
STR-DA3ES:80 W + 80 W
US Model
Canadian Model
STR-DA3ES/DA5ES
AEP Model
E Model
Chinese Model
STR-VA555ES
** “DTS”, “ES”, “DTS Digital Surround”, “DTS-ES Extended
Surround”, and “Neo: 6” are trademarks of Digital Theater
Systems, Inc.
FRONT L/R,Voltage: 2 V
CENTER,Impedance: 1 kilohms
SURROUND L/R,
SURROUND BACK,
SUB WOOFER
EQ
BASS:99 Hz~1.0 kHz
(21 steps)
MID:198 Hz~10 kHz
(37 steps)
TREBLE:1.0 kHz~10 kHz
(23 steps)
Gain levels:±10 dB, 1 dB step
Usable sensitivity50 dB/m (at 1,000 kHz or
999 kHz)
S/N54 dB (at 50 mV/m)
Harmonic distortion0.5 % (50 mV/m,
400 kHz)
Selectivity
At 9 kHz:35 dB
At 10 kHz:40 dB
4) You can change the AM tuning scale to 9 kHz or 10 kHz. After
tuning in any AM station, turn off the receiver. Hold down
TUNING + and press ?/1 . All preset stations will be erased
when you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Mono:0.3%
Stereo:0.5%
Separation45 dB at 1 kHz
Frequency response30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity60 dB at 400 kHz
AM TUNER SECTION
Tuning range
Models of area code E
With 10-kHz tuning scale:530 – 1610 kHz
With 9-kHz tuning scale:531 – 1602 kHz
Models of area code CH, AEP
With 9-kHz tuning scale:531 – 1602 kHz
AntennaLoop antenna
Usable sensitivity50 dB/m (at 1,000 kHz or
999 kHz)
S/N54 dB (at 50 mV/m)
Harmonic distortion0.5 % (50 mV/m,
400 Hz)
Selectivity
At 9 kHz:35 dB
At 10 kHz:40 dB
6) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down TUNING + and press
X/1 . All preset stations will be erased when you
change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
6)
6)
VIDEO SECTION
Inputs
Video:1 Vp-p, 75 ohms
S-video:Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Outputs
Video:1 Vp-p, 75 ohms
S-video:Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
REMOTE CONTROL
Remote control system
Infrared control
Power requirements4.5 V DC with three LR6
(size-AA) alkaline
batteries
Dimensions175 x 62 x 33 mm
Mass (approx.)135 g excluding batteries
4
STR-DA3ES/DA5ES/VA555ES
P AR T NO .
GENERAL
Power requirements
Area codePower requirements
AEP230 V AC, 50/60 Hz
CH, KR220 – 230 V AC, 50/60 Hz
E120/220/240 V AC, 50/60 Hz
Power consumption
Area codePower consumption
CH, AEP , KR390 W
E400 W
Power consumption (during standby mode)
1 W
AC outlets
Area codeAC outlets
AEP1 switched, 100 W MAX
MODEL IDENTIFICATION
– BACK PANEL –
MODELP ARTS No.
DA5ES: US model4-234-163-0s
DA5ES: CND model4-234-163-1s
DA3ES: US model4-234-163-2s
DA3ES: CND model
• Abbreviation
CND : Canadian model
CH: Chinese model
KR: Korea model
AREA CODE
E2 switched, 100 W MAX
Dimensions430 x 175 x 465 mm
including projecting parts
and controls
Mass (Approx.)17.0 kg
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-LJ305 (1)
LR6 (size-AA) batteries (3)
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY P ARTS WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS MANU AL OR IN SUPPLEMENTS PUBLISHED BY SONY .
About area codes
The area code of the receiver you purchased is
shown on the lower portion of the rear panel (see
the illustration below).
SPEAKERS
LR
SURROUND
LR
SURROUND
IMPEDANCE SELECTOR
4 8
AC OUTLET
CENTER
SURR BACK
+
SURR
SURR
BACK
BACK
R
L
–
CENTER
SURR BACK
4-XXX-XXX-XX AA
Area code
Any differences in operation, according to the
area code, are clearly indicated in the text, for
example, “Models of area code AA only”.
Fig. 1
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
5
STR-DA3ES/DA5ES/VA555ES
SAFETY CHECK-OUT
(US model only)
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
T o Exposed Metal
Parts on Set
AC
0.15 µF
Fig. A. Using an A C v oltmeter to check A C leakage.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
7.ELECTRICAL PARTS LIST ··································· 58
6
SECTION 1
S
)
SERVICE NOTE
DTS Decode Test
• Required Instrument
CD player (equipped with optical digital output)
Optical cable
DTS test CD (J-2501-154-A)
Connection:
1
CD player
3
Optical input
2
Optical
digital output
5
DTS test CD (Music Demonstration and Set Up Disc)
Procedure:
1. Set the FUNCTION of the receiver to the CD position and confirm that " [OPTICAL] " and "CD" appear on the display .
2. Insert the DTS test CD into the CD player and play the CD.
3. About three seconds later, confirm that the receiver recognizes
the optical signal and that the "DTS" and "dts [3/2]" are appear
on the display. Confirm also that MULTI CHANNEL DECODING (blue lamp) flashes on the front panel.
Music Demonstration
Track No.
1
2
3
4
5
Seal : "Prayer for the Dying"
Contents
Andrew Litton conducting
The Dallas Symphony Orchestra & Chorus:
Excerpt from Tchaikovsky: "1812 Overture"
Alan Parsons with Christopher Cross: "So Far Away"
Shoelss Joe: "The Bet"
TELARC: "A Touch of Surround Madness"
Time
5'40"
4'16"
4'08"
3'29"
6'42"
STR-DA3ES/DA5ES/VA555ES
4
Receiver STR-DA3ES/DA5ES/VA555E
Set-Up
Track No.
6
1 kHz sine (All channels)
Level Adjustment and Harmonic Distortion Analysis
7
100 Hz sine (All channels)
Verification of Signal and Subwoofer Testing
8
C-Weighted Pink Noise-Left Front Channel
9
C-Weighted Pink Noise-Center Channel
10
C-Weighted Pink Noise-Right Front Channel
11
C-Weighted Pink Noise-Right Rear Channel
12
C-Weighted Pink Noise-Left Rear Channel
13
C-Weighted Pink Noise-Subwoofer (LEE)
14
C-Weighted Pink Noise-All Channels
15
10 Hz to 20 kHz Sine Sweep
An "All Channel" Frequency Response Test
16
20 Hz to 160 Hz sine sweep
A "Subwoofer" Low Frequency Response Test
* Track numbers from 8 to 14 are for Room Equalization and Channel Iden-
tification.
Contents
Time
1'00"
1'00"
1'00"
2'00"
2'00"
2'00"
2'00"
2'00"
2'00"
2'00"
2'00"
Note: Be careful about an electrical shock caused by remains of electrical potential.
The following parts on DC board have the +B or -B electrical potential.
Heat sink for rectifier diodes D801, 802
Aluminium case of smoothing capacitor C803, 804
The 40-60V electrical voltage remains in C803, 804 when the power turns off.
Be sure to discharge in the following manner before servicing.
Discharging
1. Pull out the power cord from the wall outlet.
2. Connect 330 ohm 2W resistors between the heat
sinks for D801 and 802 and chassis individually.
3. Check the electrical potential drops fully, then start
servicing.
D801
C803
DC BOARD (COMPONENT SIDE)
330Ω 2W
(CHASSIS
D802
C804
7
STR-DA3ES/DA5ES/VA555ES
FRONT PANEL
SECTION 2
GENERAL
This section is extracted from
instruction manual.
1234 56 7 89q;
rf rdrsrar;
2CH qg
2ND ROOM (STR-DA3ES, VA555ES only)
eh
2ND/3RD ROOM (STR-DA5ES
only) eh
6.1CH indicator ql
6.1CH DECODING qk
A.F.D. q;
AUDIO SPLIT wf
CINEMA STUDIO EX qa
Cursor buttons ( I/i ) wk
Digital Cinema Sound indicator
qh
DIGITAL CONCERT HALL qd
DIMMER rs
Display 9
DISPLAY4
DOOR OPEN wg
ENTER wj
EQ ea
EQUALIZER eg
FM/AM 7
FM MODE r;
FUNCTION wd
INPUT MODE ws
IR emitter (STR-DA5ES, VA555ES only) 3
IR receptor 2
Jog dial wl
LEVEL e;
MASTER VOLUME w;
MEMORY el
MODE +/– qf
MUL TI/2CH ANALOG DIRECT
qj
MULTI CHANNEL DECODING
indicator qs
MUTING qs
NAME wa
NIGHT MODE 6
qaqsqd qf qgqhqj qkqlw;
ek eh ef es e; wl wkwh wgwf wd qswa
eg ed eaej
el
NIGHT MODE indicator 5
ON SCREEN ef
PHONES jack rf
PRESET TUNING +/– 8
PTY SELECT +/– (Models of
area code AEP only) ek
RDS/PTY (Models of area code
AEP only) ej
SET UP wh
SLEEP ej
SPEAKERS switch rd
SURROUND es
TUNING +/– ek
VIDEO 3 INPUT jacks ra
CONTROL S IN (DA3ES, DA5ES model)
S2 VIDEO OUT
VIDEO OUT
5 TV/SAT jack
CONTROL S STATAS IN (DA3ES, DA5ES model)
S2 VIDEO IN
AUDIO IN
6 DVD/LD jack
CONTROL S OUT (DA3ES, DA5ES model)
S2 VIDEO IN
VIDEO IN
AUDIO IN
7 VIDEO 2 jack
S2 VIDEO IN/OUT
VIDEO IN/OUT
AUDIO IN OUT
8 VIDEO 1 jack
CONTROL S IN/OUT
S2 VIDEO IN/OUT
VIDEO IN/OUT
AUDIO IN/OUT
wa
qkqjqhqgqfqd
9 CONTROL A1II jack
0 2ND ROOM jack
VIDEO OUT
AUDIO OUT
qa SPEAKERS terminal
FRONT
SURROUND
CENTER
SURR BACK
qs AC OUTLET
qd AC power cord (DA3ES model)
qf AC INLET (DA5ES,VA555ES model)
qg VOLTAGE SELECTOR switch (VA555ES: E model)
qh IMPEDANCE SELECTOR switch
qj SPEAKERS 3RD ROOM terminal (DA3ES, DA5ES model)
qk PRE OUT jack
FRONT
SURROUND
SURR BACK
SUB WOOFER
CENTER
ql MULTI CHANNEL INPUT 1 jack
FRONT
SURROUND
SURR BACK
CENTER
w; TAPE jack
IN/OUT
wa MULTI CHANNEL INPUT 2 jack
FRONT
SURROUND
CENTER
SUB WOOFER
ws MD/DAT jack
IN/OUT
wd CD/SACD IN jack
wf SIGNAL GND
wg RS232C connector
wh PHONO IN jack
9
STR-DA3ES/DA5ES/VA555ES
Ver 1.1 2002.10
SECTION 3
TEST MODE
FLUORESCENT INDICATOR TUBE TEST MODE
All fluorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While depressing, the [DISPLAY] and the [ENTER] buttons
simultaneously, press the power `/1 button to turn on the
main power.
2. All segments turn on at the same time, then each segment turns
on press the [DIMMER] button.
FACTORY SET MODE
All preset contents are reset to the default setting.
Procedure:
Procedure:
1. While pressing [SET UP] and [DIMMER] buttons, press `/1
button, then “TUNER FACTORY PRESET” is displayed in
several seconds and PRESET is complete.
ALL CLEAR MODE
Procedure:
1. Turn power off by pressing `/1 button.
2. Hold down `/1 button for 5 seconds, then “ENTER to Clear
All” is displayed.
3. Press ENTER button.
4. After “MEMORY CLEARING…” is displayed for a while,
“MEMORY CLEARED!” is displayed.
AM CHANNEL STEP 9 KHZ/10 KHZ
SELECTION MODE
(DA3ES, DA5ES, VA555ES: E MODELS)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Set the FUNCTION to AM. Turn off the main power.
2. While depressing the [TUNING +] button press the power `/1
button to turn on the main power.
3. Either the message AM 9kHz Step or AM 10kHz Step appears.
Select the desired step.
VERSION MODE
Procedure:
1. Turn power on by pressing `/1 button.
2. Press the [ENTER] and [SURROUND} buttons simultaneously,
then“MENU EXPAND” is displayed.
3. Press the [>] button several times to display “@@@@ ####
V.X.XX
@:Model name
#:Destination
X:Version
: Sum value
”.
SOUND FIELD CLEAR MODE
The preset sound field is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While depressing the [MODE +] button, press the power `/1
button to turn on the main power. The message S.F Initialize
appears and initialization is performed.
10
STR-DA3ES/DA5ES/VA555ES
r
SECTION 4
ELECTRICAL ADJUSTMENT
[IDLING CURRENT ADJUSTMENT]
Measuring Instrument:Digital voltmeter
Adjustment Procedure:Adjust the respective adjustment elements so that the voltage (absolute value) across the corresponding
testpoints satisfies the specification.
Channel
FRONT L
FRONT R
CENTER
SURROUND
SURROUND
SURR BACK
Test point
TP501
TP551
TP601
TP701
TP751
TP651
Adjustment element
RV501
RV551
RV601
RV701
RV751
RV651
Specification
4.0mV±0.5mV
Adjustment Location:
[POWER AMP BOARD]
TP501
RV501
TP701
RV701
RV601
TP651
TP601
VR651
TP551
RV551
VR751
[OSD ADJUSTMENT]
Measuring Instrument:frequency counter
Procedure:
1. Connect the frequency counter to check connector (TP201) of
the S VIDEO board.
2. Connect between Pin 3 to Pin 4 of TP201 by lead wire.
3. Adjust the respective adjustment element so that the frequency
counter read specification.
TP751
S- VIDEO
BOARD
TP201
1
4
frequency counte
+
–
Shorting
Adj.
MODEL
NTSC
VA555ES
PAL
Adjustment
element
CT202
(CLOCK BOARD)
CT201
(CLOCK BOARD
I
DA3ES, DA5ES
II
All models
CT203
(S-VIDEO BOARD)
CT204
(S-VIDEO BOARD)
4. After check, remove the lead wire connected in step 2.
Adjustment Location:
[S-VIDEO BOARD]
CT204
CT203
1
4
TP201
measurement
point
TP201
Pin 1
TP201
Pin 2
Specification
3.579545MHz ±50Hz
4.433618MHz ±50Hz
3.57954MHz ±50Hz
7.20MHz ±0.01MHz
[CLOCK BOARD]
CT202
CT201
11
STR-DA3ES/DA5ES/VA555ES
d
5-1. CIRCUIT BOARDS LOCATION
AC board
4/8 board
VOL SEL board
(VA555ES: E)
DC board
SECTION 5
DIAGRAMS
SPTM board
3RD ROOM SPTM board (DA3ES, DA5ES)
E-VOL board
M-BUS board (DA3ES, DA5ES)
LED board
HP board
VIDEO 3 board
DISPLAY board
M-VOL board
FUNCTION board
CLOCK board (VA555ES)
S-VIDEO board
C-VIDEO board
INPUT board
DIGITAL INPUT boar
DIGITAL board
SUB DSP board (DA5ES, VA555ES)
AMP board
12
STR-DA3ES/DA5ES/VA555ES
2.6Vp-p
60nsec
16.5MHz
3.5Vp-p
74nsec
13.5MHz
3.5Vp-p
74nsec
12.5MHz
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(IN ADDITION TO THIS NECESSARY NOTE IS PRINTED
IN EACH BLOCK.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
•%: indicates tolerance.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Note:
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
W or less unless otherwise
4
For printed wiring boards.
Note:
• X : parts extracted from the component side.
•a: Through hole.
• b : Pattern from the side which enables seeing.
• There are few cases that the part isn't mounted in model is printed
on diagram.
C
Q
These are omitted
EB
E
CB
These are omitted
C
BE
These are omitted
There are a few cases that the part printed on
this diagram isn't mounted in the model.
• Waveform
• DIGITAL SECTION
1 IC1901 qh (X OUT)
137nsec
7.28MHz
2 IC2001 tk (XO)
3 IC1103 7
24.576MHz
4 IC1201 qs (MCLK2)
5.0Vp-p
3.2Vp-p
• S-VIDEO SECTION
1 IC209 9 (XS)
14.31818MHz
2 IC207 5
14.31MHz
3 IC207 7
17.34MHz
2.1Vp-p
5.0Vp-p
5.0Vp-p
• SUB DSC SECTION
1 IC9011 4
4.0Vp-p
20MHz
2 IC9012 2A1
3.3Vp-p
21µsec
3 IC9012 3A2
3.3Vp-p
330nsec
• U : B+ Line.
• V : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
No mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
F: FM
J: CD (ANALOG)
c : CD (DIGITAL)
• Abbreviation
CND : Canadian model
CH: Chinese model
KR: Korea model
5 IC1401 (MCLK2)
6 IC1501 (MCLK2)
139
139
3.6Vp-p
12.5MHz
1313
STR-DA3ES/DA5ES/VA555ES
5-2. BLOCK DIAGRAM – AUDIO SECTION –
VIDEO
2
VIDEO
1
ANTENNA
CD/SACD IN
MD/
DAT
TAPE
TV/
SAT
DVD
/LD
AUDIO
AUDIO
2ND
ROOM
FM 75Ω
COAXIAL
PHONO IN
OUT
OUT
AUDIO
IN
AUDIO
IN
OUT
OUT
AUDIO
OUT
AM
IC302
AUDIO SELECTOR
J301
L
L
J302
L
L
IN
J303
L
L
IN
L
J304
L
L
L
IN
J305
L
IN
L
L
TUNER UNIT
TU101
TUN-LCH
TUN-RCH
FMDETOUT
STEREO
TUNED
MUTE
SIGNAL
COMCLK
COM DAT
TUN LAT
DO
IC301
3
6
4
7
1
2
3
10
12
13
14
15
LCOM
1
R-CH
PHONO
2
PHONO
41
CD/SACD
3
CD/SACD
40
MD/DDATOUT
4
MD/DATIN
5
MD/DATIN
38
TAPE OUT
6
TAPEIN
7
TAPEIN
36
TV/SAT
8
TV/SAT
35
DVD/LD
9
DVD/LD
34
VIDEO2OUT
10
VIDEO2IN
11
VIDEO2IN
32
VIDEO1OUT
12
VIDEO1IN
13
VIDEO1IN
30
3RD AUDIO SELECTOR
PHONOTUNER
2
CD/SACD
3
MD/DATIN
4
TAPE IN
5
TV/SAT
6
DVD/LD
7
VIDEO2IN
8
VIDEO1IN
9
RY301
RDS CLK
RDS DATA
TUN-STEREO
TUN-TUNED
TU-MUTE
TUN-SIGNAL
TUN-DATAOUT
COM-CLK
COM -DATA
TUN -LAT
IC304
LCOM
LCOM
LCOM
TUNER
TUNER
VIDEO3
VIDEO3
DATA
VIDEO3
3RDAUDIO
DATA
IC305
75
Q304
RELAY
DRIVE
D
15
16
27
28
14
29
17
26
CLK
21
22
LAT
23
10
11
12
CLK
14
15
LAT
16
DIGITAL
SECTION
(2/2)
CLK
S.DATA
FUN-LAT
CLK
S.DATA
FUN-LAT
2NDAU-RY
IC306
31
4
2
16
IC2101
RDS
J102
L
VA555ES: AEP
13
14
X1201
ADLCH
VIDEO3
INPUT
AUDIO
IC307
31
B
DIGITAL
SECTION
(1/2)
MULTI
CHANNEL
INPUT
MULTI
CHANNEL
INPUT
1
2
C
DIGITAL
SECTION
(2/2)
FRONT
SURROUND
SURR BACK
FRONT
SURROUND
J407
RS232C
J402
J403
CENTER
SUB
WOOFER
CENTER
SUB
WOOFER
J401
9
8
7
6
D-SWCH
D-CCH
D-SLCH
D-LCH
D-SBLCH
L
L
L
L
L
5
4
3
2
1
IC402
SURROUND SELECTOR
COML IN
3
DSWIN
28
DCIN
15
DSLIN
7
DLIN
2
DSBLIN
11
M1LIN
4
M1SLIN
8
M1SBLIN
12
M1CIN
16
M1SWIN
27
M2LIN
5
M2SLIN
9
M2CIN
17
M2SWIN
26
2NDLIN
18
IC401
RS232C INTERFACE
R1IN
R1OUT1
16
T1OUT
17
LOUT
SL OUT
SBL OUT
C OUT
SW OUT
DATA
T1IN
6
10
14
19
24
CLK
21
22
LAT
23
DIGITAL
SECTION
(1/2)
15
13
RY401
E
VIDEO
SECTION
Q401
RELAY
DRIVE
SSM MODC
F
DIR-RY
CLK
S.DATA
FUN-LAT
XTAL SELECTOR
VIDEOG
CLK
S.DATA
VOL-LAT
CLK
S.DATA
VOL-LAT
PREOUT-RY
CLK
S.DATA
VOL-LAT
3RD-RY
PREOUT-RY
CLK
S.DATA
VOL-LAT
SBR-RY
PREOUT-RY
2NDAU-RY
SBR-RY
DIR-RY
PREOUT-RY
3RD-RY
IC403
ELECTRONIC VOLUME
MIN5M-OUT
7
CLK1
T-OUT
10
DATA
11
12
ELECTRONIC VOLUME
10
11
12
ELECTRONIC VOLUME
10
11
12
ELECTRONIC VOLUME
14
10
11
12
LAT
IC404
7
MIN M-OUT
CLK1
DATA
LAT
IC406
MIN M-OUT
7
CLK1
DATA
LAT
IC405
MIN
7
MIN
CLK
DATA
LAAT
T-IN
T-OUT
T-IN
T-OUT
T-IN
M-OUT
T-OUT
T-IN
M-OUT
T-OUT
T-IN
IC2103(1/2)
DATA DECODER
2AU-RY
11
SBR-RY
10
DIR-RY
9
PRE-RY
8
5
3RD-RY
21
SSMMODC
22
OSDXSEL
VIDEOG
23
16
17
18
IC407
3
1
2
4
3
IC408
3
5
4
3
5
4
3
5
4
3
2
Q404
RELAY
DRIVE
Q425
RELAY
DRIVE
IC410
3
2
Q403
RELAY
DRIVE
Q406
RELAY
DRIVE
IC409
(1/2)
3
2
IC409
(2/2)
5
6
Q402
RELAY
DRIVE
RELAY
DRIVE
Q407
DATA
CLK
STB
CLR
1
RY404
RY405
RY403
1
(1/2)
RY403
(1/2)
1
RY402
7
13
14
15
89
16
10 11
IC2104
BUFFER
RY406
RY407
FL
SL
SB
CENTER
J404
J405
CLK
S.DATA
VOL-LAT
FUN-LAT
COM DATA
COM CLK
RY-STB
RY-CLR
RXD232
TXD232
POWER AMP
SECTION
L
FRONT
L
SURROUND
L
SURR BACK
L
SUB WOOFER
R
CENTER
A
G
H
I
PRE
OUT
DIGITAL
SECTION
(2/2)
DIGITAL
SECTION
(2/2)
DIGITAL
SECTION
(2/2)
•R-ch is omitted due to same as L-ch
•Signal Path
: CD (ANALOG)
: FM
1414
– VIDEO SECTION –
STR-DA3ES/DA5ES/VA555ES
COMPONENT
VIDEO
S2 VIDEO
S2 VIDEO
TV/SAT
IN
DVD/LD
IN
IN
VIDEO2
VIDEO 1
DVD/LD
VIDEO 1
VIDEO 2
VIDEO 3
INPUT
S2 VIDEO
VIDEO IN
DVD/LD
VIDEO IN
VIDEO 3
INPUT
VIDEO
2ND ROOM
VIDEO
J207
CTRL
A1
PB/B-Y
PR/R-Y
PB/B-Y
PR/R-Y
TV/SAT
OUT
OUT
TV/SAT
OUT
OUT
OUT
J212
(1/2)
Y
Y
J210
C
Y
C
Y
J208
C
Y
J209
J102(1/3)
J200(1/2)
J201
J202(1/2)
J102(2/3)
J202
(2/2)
C
Y
C
Y
C
Y
C
Y
IN
IN
IN
IN
-5V
-5V
22
1
8
14
5
16
19
8
16
+5V
3
5
15
13
11
9
7
8
16
+5V
3
5
11
9
15
13
7
3
5
9
13
7
1
IC214
SELECTOR
13
12
3
5
1
2
INH
6
IC203
VIDEO SELECT SW
VIN5
VIN4
VIN2
VIN1
VOUT3
VIN2
VIN3
VEE
VDD
VIDEO SELECT SW
TV INSW1
LD IN
V1 OUT
V1 IN
V2 OUT
V2 IN
V3 IN
VEE
VDD