Sony STR-DA80ES, STR-TA-V88ES, STR-TA-VA80ES Service Manual

STR-DA80ES/TA-V88ES/TA-VA80ES
SERVICE MANUAL
Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby,” the double-D symbol a, “AC-3” and “Pro Logic” are trademarks of Dolby Laboratories Licensing Corporation.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
With 8-ohm load, both channels driven, from 20-20,000 Hz, rated 100 watts per channel, minimum RMS power, with no more than
0.09 % total harmonic distorition from 250 milliwatts to rated output (US model).
Amplifier section
POWER OUTPUT Stereo mode STR-DA80ES:
Surround mode STR-DA80ES:
(8 ohms 20 Hz-20 kHz, THD 0.05 %) 100 W + 100 W TA-V88ES: (6 ohms at 1 kHz, THD 0.7%) 100 W + 100 W TA-VA80ES: (4 ohms at 1 kHz, THD 0.7%) 100 W + 100 W
(8 ohms at 1 kHz, THD 0.05 %) Front : 100 W + 100 W
1)
Center Rear T A-V88ES: (6 ohms at 1 kHz, THD 0.7%) Front : 100 W + 100 W Center Rear T A-VA80ES: (4 ohms at 1 kHz, THD 0.7%) Front : 100 W + 100 W Center Rear
1)
1)
1)
1)
1)
: 100 W : 100 W + 100 W
: 100 W : 100 W + 100 W
: 100 W : 100 W + 100 W
Dynamic power output
Harmonic distortion at rated output
Frequency response
Photo: STR-DA80ES
SPECIFICATIONS
1)
Depending on the sound field settings and the source, sound will not be output.
155 W + 155 W, 8 ohms 220 W + 220 W, 4 ohms (STR-DA80ES: US, Canadian)
PHONO:
RIAA equalization curve
±0.5 dB CD, T APE, D AT/MD, VIDEO 1, 2, 3, LD/DVD, TV (/DBS):
10 Hz-50 kHz dB (with
DIRECT PASS on)
US Model
Canadian Model
STR-DA80ES
AEP Model
UK Model
TA-VA80ES
E Model
STR-DA80ES/TA-VA80ES
Australian Model
PX Model
STR-DA80ES
Chinese Model
TA-V88ES
Inputs
S/N
network, input level)
50 75 dB
100 dB
100 dB
(A, 20 kHz, LPF)
100 dB
+0.5 –2
Sensitivity Impedance (weighting
PHONO 2.5 mV
200 mV
CD
TAPE, DAT/ MD, VIDEO 1, 2, 3 LD, TV/DBS
TUNER 150 mV (TA-V88ES/VA80ES)
LD DVD AC-3 RF IN (A, 20 kHz, LPF)
LD DVD COAXIAL 0.5 Vp-p 75 IN
LD DVD/TV (DBS)/CD/ DAT MD (A, 20 kHz, LPF) OPTICAL IN
(STR-DA80ES)
150 mV
(TA-V88ES/VA80ES)
200 mV 50 82 dB
(STR-DA80ES)
150 mV
(T A-V88ES/VA80ES)
kilohms (A, 2.5 mV)
kilohms (A, 150 mV)
75
——
STR-DA80ES
FM STEREO/FM-AM RECEIVER
TA-V88ES/TA-VA80ES
INTEGRATED AV AMPLIFIER
MICROFILM
Outputs REC OUT: DAT/MD, TAPE
Voltage: 200 mV
(STR-DA80ES) 150 mV (TA-V88ES/VA80ES)
Impedance: 1 kilohm
AUDIO OUT: VIDEO 1, 2
Voltage: 200 mV
(STR-DA80ES) 150 mV (TA-V88ES/VA80ES)
Inpedance: 1 kilohm
PRE OUT:
Voltage: 2 Vrms Impedance: 1 kilohm
PHONES:
Accepts low and high impedance headphones
BASS BOOST +6 dB at 70 Hz
(STR-DA80ES)
+10 dB at 70 Hz
(TA-V88ES/VA80ES)
Digital signal processor section
Modulation (A/D conversion)
High Density Linear
Converter
Demodulation (D/A conversion)
High Density Linear
Converter (Advanced pulse D/A converter)
Sampling frequency
48 kHz
Surround LFE MIX:
MUTE, –20 - 0 dB, 0.5 dB step
D.RANGE COMP:
OFF, 0.1 - 0.9, STD, MAX
REAR level:
–20 - +10 dB, 0.5 dB step
CENTER level:
–20 - +10 dB, 0.5 dB step
SUB WOOFER level:
–20 - +10 dB, 0.5 dB step
EFFECT:
21-step adjustable
WALL:
17-step adjustable
SEAT
F/R: 17-step adjustable L/R: 17-step adjustable
REBERB time:
17-step adjustable
Equalizer BAND: BASS/TREBLE
Turnover frequency:
Bass: 99 Hz-992 Hz Treble: 1.0 kHz-8.6 kHz
Level: ±10 dB, 0.5 dB step
FM tuner section (STR-DA80ES)
Tuning range 87.5-108.0 MHz
Antenna terminals
75 ohms, unbalanced
Sensitivity Mono: 18.3 dBf, 4.5 µV
Stereo: 38.3 dBf, 45 µV
Usable sensitivity
11.2 dBf, 2 µV (IHF)
S/N Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3 % Stereo: 0.5 %
Separation 45 dB at 1 kHz
Frequency response
30 Hz-15 kHz dB
+0.5 –2
Selectivity 60 dB at 400 kHz
AM tuner section (STR-DA80ES)
Tuning range With 10 kHz interval:
530-1710 kHz (US and Canadian models3)) 530-1610 kHz (models for all other countries except for Australia)
With 9 kHz interval:
531-1710 kHz (US and Canadian models) 531-1602 kHz (Australian model and models for all other countries3))
Antenna Loop antenna
Usable sensitivity
50 dB/m (at 1,000 kHz or 999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion
0.5 % (50 mV/m, 400 kHz)
Selectivity At 9 kHz: 35 dB
At 10 kHz: 40 db
3)
You can change the AM tuning interval to 9 kHz (US and Canadian models) or to 10 kHz (models for all other countries except for Australia). After tuning in any AM station, turn off the receiver. Hold down the PRE­SET TUNING + button and press the POWER button. All preset stations will be erased when you change the interval. To re­set the interval to 10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-; 75 ohms C: 0.286 Vp-p 75 ohms
Outputs VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms
General
System Tuner section:
PLL quartz-locked digital synthesizer system (STR-DA80ES)
Preamplifier section:
Low-noise NF type equalizer
Power amplifier section:
Pure-complementary parallel P.P.
Power requirements
US and Canadian models:
120 V AC, 60 Hz
Australian model:
240 V AC, 50 Hz
European models:
230 V AC, 50 Hz
Other models:
120/220/240 V AC selectable, 50/60 Hz
Power consumption
STR-DA80ES:
US model: 340 W Canadian model: 500 VA Australian model: 380 W
Other models: 380 W TA-V88ES: 370 W TA-VA80ES: 380 W
AC outlets STR-DA80ES:
US and Canadian models:
2 switched, total
120 W Australian model:
1 switched, maximum
100 W Other models:
2 switched, total
100 W T A-V88ES/VA80ES:
1 switched, maximum 100 W
Dimensions 430 × 160 × 435 (4404)) mm
(17 × 63/8 × 17 1/4 (17 3/8) inches) including projecting parts and controls
4)
When the front cover is open
Mass (Approx.) 15.9 kg (35 Ib 1 oz)
(STR-DA80ES)
15.6 kg (TA-V88ES/VA80ES)
Supplied accessories
FM wire antenna (1) (STR-DA80ES) AM loop antenna (1) (STR-DA80ES) Remote commander RM-P501 (remote) (1) Size AA (R6) batteries (2)
Design and specifications are sbuject to change without notice.
– 2 –
TABLE OF CONTENTS
1. GENERAL ................................................................... 4
2. DISASSEMBLY.......................................................... 7
3. ELECTRICAL ADJUSTMENTS......................... 9
4. DIAGRAMS
4-1. IC Pin Function Description............................................ 10
4-2. Schematic Diagram – DISPLAY Section – .................... 24
4-3. Printed Wiring Boards – DISPLAY Section –................ 29
4-4. Schematic Diagram – VIDEO Section – ......................... 33
4-5. Printed Wiring Boards – VIDEO Section – .................... 37
4-6. Schematic Diagram
– INPUT/TUNER/POWER Section –............................. 41
4-7. Printed Wir ing Boards
– INPUT/TUNER/POWER Section –............................. 45
4-8. Schematic Diagram – DIGITAL Section –...................... 50
4-9. Printed Wiring Boards – DIGITAL Section – ................ 55
4-10. Schematic Diagram – AMP/OUTPUT Section – ............ 59
4-11. Printed Wiring Boards – AMP/OUTPUT Section –....... 63
5. EXPLODED VIEWS ................................................ 69
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow­ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT -540A. Follo w the manufacturers’ instructions to use these instruments.
2. A battery-operated A C milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica­tion is 0.75 V, so analog meters must have an accurate low­voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex­amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V A C range are suit­able. (See Fig. A)
6. ELECTRICAL PARTS LIST................................ 74
MODEL IDENTIFICATION
– BACK PANEL –
4-991-
STR-DA80ES US Model : 373-3 STR-DA80ES Canadian Model : 373-4 STR-DA80ES Australian Model : 373-5 STR-DA80ES E, PX Model : 373-6 TA-V88ES Chinese Model : 374-4 TA-VA80ES AEP, UK, German,
EE, CIS Model : 374-0
TA-VA80ES E, Malaysia,
Singapore Model : 374-3
π π π π π
π
π
To Exposed Metal Parts on Set
1.5 k
0.15 µF
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE P AR DES PIÈCES SONY DONT LES NUMÉR OS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Earth Ground
AC voltmeter (0.75 V)
– 3 –
– 4 –
Front Panel Description
• STR-DA80ES
instruction manual.
GENERAL
This section is extracted from
SECTION 1
– 5 –
Front Panel Description
• T A-V88ES
– 6 –
Front Panel Description
• T A-V A80ES
SECTION 2
1
connector
(CNE910)
1
connector
(CNV903)
1
connector
(CNV902)
3
two screws
(BVTP 3 × 6)
4
back panel section
2
seven screws
(BVTP 3
×
8)
1
connector
(CNE807)
2
two screws
(BVTP 3
×
8)
(STR-DA80ES)
2
eight screws
(BVTP 3
×
8)
2
seven screws
(BVTP 3
×
8)
1
connector
(CND3503)
2
four screws
(BVTP 3
×
8)
2
screw
(BVTP 3
×
8)
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
CASE
1
two screws
(M 3
1
1
three screws
×
8)
(M 3
×
8)
2
2
three screws
×
8)
(M 3
3
case
1
two screws
(M 3
×
8)
REAR PANEL SECTION
– 7 –
TUNER/AUDIO/SPTM BOARD, FRONT PANEL SECTION
1
connector (CNE211)
8
front panel section
7
four screws
(BVTP 3
×
8)
1
connector (CNS210)
1
five connectors
CND621, CNE601, 602,
(
CNV615, 616
)
2
SPTM board
STR-DA80ES
1
connector
(CNS623)
7
three screws (BVTP 3
×
INPUT BOARD
3
claw
8)
3
AUDIO board
2
five screws (BVTP 3
4
flat wire (CNS3503)
5
connector
(CNS201)
×
8)
1
connector
(CNV613)
1
connector (CNE939)
6
TUNER board
2
two screws (BVTP 3
×
8)
1
five connectors
CNE601, 620, 622, 3501,
(
CNP202
4
INPUT board
)
– 8 –
r
h
SECTION 3
ELECTRICAL ADJUSTMENTS
DC BIAS CURRENT Adjustment (with no signal input)
Note:
1. DC BIAS CURRENT adjustments should be made 30 seconds after the POWER switch is turned on (POWER ON).
2. After replacing the power transistors, DC BIAS CURRENT adjustments should be perfomed.
Procedure:
1
2
3
Digital volt mete
+ –
AMP BOARD
R615 R665 R016 R715 R765
[AMP BOARD] (COMPONENT SIDE)
FRONT Rch
R665
RV651
Connecting Adjustment Reading on point part Digital volt meter
FRONT Lch R615 RV601 20 mV FRONT Rch R665 RV651 20 mV CENTER R016 RV001 20 mV REAR Lch R715 RV701 20 mV REAR Rch R765 RV751 20 mV
1 2
3
D973
C987
C988
D971 D972
R618
3
RV601
FRONT Lc
REAR Rch
R668
R765
RV751
1 2
3
R768
R017
C985
C986
RV001
CENTER
2 1
R615
R718
RV701
R715
R016
3211
REAR Lch
3 2
– 9 –
SECTION 4
DIAGRAMS
4-1. IC Pin Function Description
DISPLAY BOARD IC105 MB90673PF-G-206-BND
(FLUORESCENT INDICATOR TUBE DRIVE CONTROLLER, KEY CONTROL)
Pin No. Pin Name I/O Function
1 MBUS (VZ) I Not used (fixed at “L”) 2 MBUS (MON) I Not used (fixed at “L”) 3 MBUS (STU) O Not used (open) 4 LED-V3 O LED drive signal output terminal “H”: LED on (for function VIDEO 3 indicator) 5 LED-V2 O LED drive signal output terminal “H”: LED on (for function VIDEO 2 indicator) 6 LED-V1 O LED drive signal output terminal “H”: LED on (for function VIDEO 1 indicator) 7 STANDBY O LED drive signal output terminal “H”: LED on (for function STANDBY indicator) 8 DPC (SURR) O LED drive signal output terminal “H”: LED on (for function SUR indicator)
9 DPC (EQ) O LED drive signal output terminal “H”: LED on (for function EQ indicator) 10 DPC (INDEX) O LED drive signal output terminal “H”: LED on (for function INDEX indicator) 11 DVSS Ground terminal 12 LED-CE O LED drive signal output terminal “H”: LED on (for function CD indicator) 13 LED-DAT/MD O LED drive signal output terminal “H”: LED on (for function DAT/MD indicator) 14 LED-TAPE O LED drive signal output terminal “H”: LED on (for function TAPE indicator)
15 LED-TV O 16 LED-LD O LED drive signal output terminal “H”: LED on (for function LD/DVD indicator)
17 LED-V3 O LED drive signal output terminal “H”: LED on (for function VIDEO 3 indicator) 18 LED-V2 O LED drive signal output terminal “H”: LED on (for function VIDEO 2 indicator) 19 LED-V1 O LED drive signal output terminal “H”: LED on (for function VIDEO 1 indicator) 20 RX (SIN) I Receive data input from the on screen display controller Not used (fixed at “L”) 21 TX (SOUT) O Transmit data output to the on screen display controller Not used (open) 22 BUSY I Busy signal input from the on screen display controller Not used (fixed at “L”) 23 FL CLEAR O “Display clear signal output to the fluorescent indicator tube driver (IC101, 102)” 24 FL DATA O Serial data output to the fluorescent indicator tube driver (IC102) 25 FL CLK O “Serial data transfer clock signal output to the fluorescent indicator tube driver (IC101, 102)” 26 LAT (OSD) O “Serial data latch pulse signal output to the fluorescent indicator tube driver (IC101, 102)” 27 SIRCS1 I Sircs signal input from the remote control receiver (IC104) 28 AVCC Power supply terminal (+5V) 29 AVR+ I Reference voltage input terminal (+5V) 30 AVR– I Reference voltage input terminal (+0V) 31 GND Ground terminal
32 AD KEY IN 1 I
33 AD KEY IN 2 I S116 to 119 (FM/AM, SHIFT, PRESET TUNING +/– keys) (STR-DA80ES).
34 DVSS Ground terminal
35 AD KEY IN 3 I
36 AD KEY IN 4 I
37 AD KEY IN 5 I
38 AD VERSION I Setting terminal for the destination (A/D input) 39 VOL-UP I Motor drive signal input for the master volume 40 VOL-DOWN I Motor drive signal input for the master volume
LED drive signal output terminal “H”: LED on (for function TV/DBS (STR-DA80ES) or TV (TA-V88ES/VA80ES) indicator)
Key input terminal (A/D input) S132 to 134 (INPUT MODE, DIRECT PASS, BASS BOOST keys)
Key input terminal (A/D input)
Not used (open) (TA-V88ES/VA80ES)
Key input terminal (A/D input) S109 to 114 (STR-DA80ES: EQUALIZER BAND, TUNING +/–, FM MODE, MEMORY, DISPLA Y keys) (TA-V88ES/VA80ES: EQU ALIZER BAND, EQU ALIZER ON/OFF , SOUND FIELD STANDARD, SLEEP, DIMMER)
Key input terminal (A/D input) S101 to 108 (EQUALIZER CH, DPC MODE, cursor ///, SET UP, OPEN/CLOSE keys)
Key input terminal (A/D input) S129 to 131 (MODE, SOUND FIELD ON/OFF, GENRE keys)
– 10 –
Pin No. Pin Name I/O Function
41 MODE0 I Mode selection terminal (fixed at “H”) 42 MODE1 I Mode selection terminal (fixed at “H”) 43 MODE2 I Mode selection terminal (fixed at “L”) 44 STANDBY I Hardware standby signal input terminal (fixed at “H”) 45 STOP I Stop signal input terminal 46 U-RESET I System reset signal input from the master controller (IC3413) “L”: reset 47 U-SREQ O Communication request signal output to the master controller (IC3413) 48 U-MREQ I Communication request signal input from the master controller (IC3413) 49 U- DATA I/O Serial data in/out with the master controller (IC3413) 50 U-CLOCK I Serial data reading clock signal input from the master controller (IC3413) 51 HIFI/ES I Setting terminal for the destination (fixed at “H”) 52 AUBUS-IN I Audio bus signal input terminal 53 AUBUS-OUT O Audio bus signal output terminal 54 FUNCTION-B I Jog dial pulse input of the rotary encoder (RV101 FUNCTION) 55 FUNCTION-A I Jog dial pulse input of the rotary encoder (RV101 FUNCTION) 56 OUT-OPEN O Motor drive signal output to the door open/close motor drive (IC107) 57 OUT-CLOSE O Motor drive signal output to the door open/close motor drive (IC107) 58 SW-OPEN I Door open detect sensor (PH102) input terminal 59 SW-CLOSE I Door close detect sensor (PH103) input terminal 60 Not used (open) 61 SWBAL I Balance volume on/off detect signal input terminal 62 RESET I Reset signal input terminal “L”: reset 63 GND Ground terminal 64 XO O System clock signal output terminal (4MHz) 65 XI I System clock signal input terminal (4MHz) 66 VCC Power supply terminal (+5V) 67 LED-TUNER O LED drive signal output terminal “H”: LED on (for function TUNER indicator) 68 LED-PHONO O LED drive signal output terminal “H”: LED on (for function PHONO indicator) 69 LED MUTE O LED drive signal output terminal “H”: LED on (for MUTING indicator) 70
LED-LEARNING 71 LED D.PASS O LED drive signal output terminal “H”: LED on (for DIRECT PASS indicator) 72 LED-INPUT O LED drive signal output terminal “H”: LED on Not used (open) 73 LED VOL O LED drive signal output terminal “H”: LED on (for MASTER VOLUME illumination) 74 LED BASS.B O LED drive signal output terminal “H”: LED on (for BASS BOOST indicator) 75 SP-A I Speaker select switch (S135) input terminal “H”: speaker A on 76 SP-B I Speaker select switch (S135) input terminal “H”: speaker B on 77 PW-SW I Power switch (S137) input terminal 78 LED-TV O LED drive signal output terminal “H”: LED on (for function TV/DBS (STR-DA80ES) or
79 LED-LD O LED drive signal output terminal “H”: LED on (for function LD/DVD indicator) 80 I Not used (fixed at “L”)
O LED drive signal output terminal “H”: LED on Not used (open)
TV (TA-V88ES/VA80ES) indicator)
– 11 –
DIGITAL BOARD IC3308 SN-PM4007A (DOLBY (AC-3) DEMODULATOR)
Pin No. Pin Name I/O Function
1 GND — 2 VDD — 3 RESET I 4 OSCON I 5 DATA I 6 MCK I 7 MLTB I 8 IDST O
9 IDCK O 10 IDO O 11 TM0 I 12 ECCK O 13 DEY O 14 DRY O 15 DRY O 16 TM1 I 17 A0 O 18 A1 O 19 A2 O 20 A3 O 21 A4 O 22 A5 O 23 TM2 I 24 TM3 I 25 XOUT O 26 XIN I 27 NEXT I 28 GND — 29 VDD — 30 A6 O 31 A7 O 32 GND — 33 VDD — 34 A12 O 35 A14 O 36 WE O 37 A13 O 38 A8 O 39 A9 O 40 GND — 41 A11 O 42 OE O 43 A10 O 44 D7 I/O 45 D6 I/O
Ground terminal Power supply terminal (+5V) Reset signal input from the master controller (IC3413) “L”: reset Oscillation on/off control signal input terminal “H”: on (fixed at “H”) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (fixed at “L”) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (fixed at “L”)
Address signal output to the S-RAM (IC3309)
Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) System clock output terminal Not used (open) System clock input terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Ground terminal Power supply terminal (+5V) Address signal output to the S-RAM (IC3309) Address signal output to the S-RAM (IC3309) Ground terminal Power supply terminal (+5V) Address signal output to the S-RAM (IC3309) Address signal output to the S-RAM (IC3309) Write enable signal output to the S-RAM (IC3309) “L” active
Address signal output to the S-RAM (IC3309)
Ground terminal Address signal output to the S-RAM (IC3309) Output enable signal output to the S-RAM (IC3309) “L” active Address signal output to the S-RAM (IC3309)
Two-way data bus with the S-RAM (IC3309)
– 12 –
Pin No. Pin Name I/O Function
46 D5 I/O 47 D4 I/O 48 D3 I/O 49 D2 I/O 50 D1 I/O 51 D0 I/O 52 VDD — 53 GND — 54 55 VIN I 56 VOUT O 57 TI2 I 58 TI3 I 59 TLD8 I 60 TCK I 61 TRP O 62 TD0 O 63 PD0 O 64 TI4 I 65 PDD15 I 66 MUT0 O 67 TI5 I 68 VLDY O 69 DASYO O 70 DAOUT O
71 DAIN I
72 DASEL I 73 TI8 I
74 C2F1 O
TI1
Two-way data bus with the S-RAM (IC3309)
Power supply terminal (+5V) Ground terminal
I
Test terminal Not used (fixed at “H”) VCXO input terminal (18.432 MHz) VCXO output terminal (18.432 MHz) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Test terminal Not used (open) Test terminal Not used (open) Internal phase comparator output terminal Test terminal Not used (fixed at “L”) PDO out control signal input terminal “L”: on Mute control signal output terminal “H”: mute on Test terminal Not used (fixed at “L”) Test terminal Not used (open) Test terminal Not used (open) Digital out signal output terminal (serial data stream output)
Digital external input terminal Through out to DAOUT (pin ) when DASEL (pin &™)is “H” Not used (open)
Digital out selection terminal Fixed at “L” Test terminal Not used (fixed at “L”)
C2 error correction state monitor output terminal Outputs if corrected properly Not used (open)
75 C2F0 O
76 C1F1 O
77 C1F0 O
78 MUT1 I 79 VDD — 80 GND — 81 AVDD — 82 CPIN I 83 CMIN I 84 AGND — 85 TM4 I 86 VDD — 87 DIN I
C2 error correction state monitor output terminal Outputs number of errors at C2 Not used (open)
C1 error correction state monitor output terminal Outputs whether error is present at C1 Not used (open)
C1 error correction state monitor output terminal Outputs number of errors at C1 Not used (open)
Mute signal input terminal “H”: mute Power supply terminal (+5V) Ground terminal Power supply terminal (+5V) (for analog system) Comparator input (+) terminal Comparator input (–) terminal Ground terminal (for analog system) Test terminal Not used (fixed at “L”) Power supply terminal (+5V) Test terminal Not used (fixed at “L”)
– 13 –
Pin No. Pin Name I/O Function
88 DOUT O 89 DOUTB O 90 CSM O 91 GND — 92 WINGT O 93 SYST0 O 94 SYST1 O 95 ADST0 O 96 ADST1 O 97 TMS I 98 BUNR1 I 99 AGND
100 AVDD
Comparator output terminal Comparator inverted output terminal Clock (9.216 MHz) output terminal Not used (open) Ground terminal Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (open) Test terminal Not used (fixed at “L”) Test terminal Not used (fixed at “L”) Ground terminal (for analog system) Power supply terminal (+5V) (for analog system)
– 14 –
DIGITAL BOARD IC3410 DSP56009FJ88F (DIGITAL SIGNAL PROCESSOR)
Pin No. Pin Name I/O Function
1 AGND
Ground terminal (for address bus buffer)
2 MCS0 O
Chip select signal output to the external RAM device Not used (open)
3 MCS3 O
Chip select signal output to the external RAM device Not used (open)
4 MA14 O
Address signal output to the external RAM device Not used (open)
5 MA13 O
Address signal output to the external RAM device Not used (open)
6 AVCC
Power supply terminal (+5V) (for address bus buffer)
7 MA12 O
Address signal output to the external RAM device Not used (open)
8 AGND
Ground terminal (for address bus buffer)
9 QVCC
Power supply terminal (+5V) (for internal logic)
10 QGND
Ground terminal (for internal logic)
11 MA11 O 12 MA10 O 13 MA9 O 14 MA8 O 15 AGND
Ground terminal (for address bus buffer)
16 MA7 O
Address signal output to the external RAM device Not used (open)
17 AVCC
Power supply terminal (+5V) (for address bus buffer)
18 MA6 O 19 MA5 O
Address signal output to the external RAM device Not used (open)
20 MA4 O 21 AGND
Ground terminal (for address bus buffer)
22 MA3 O 23 MA2 O 24 MA1 O 25 MA0 O 26 SCK I
Serial data reading clock signal input from the master controller (IC3413)
27 EXTAL I
Master clock signal input terminal (3MHz)
28 QVCC
Power supply terminal (+5V) (for internal logic)
29 QGND
Ground terminal (for internal logic)
30 PINIT I
Initialize input for the PLL circuit (fixed at “L”)
31 PGND
Ground terminal (for PLL circuit)
32 PCAP I
Connected to the external capacitor for PLL circuit filter
33 PVCC
Power supply terminal (+5V) (for PLL circuit)
34 SGND
Ground terminal (for serial port)
35 MISO I
Communication data input from the master controller (IC3413)
36 RESET I
Reset signal input from the master controller (IC3413) “L”: reset
37 MODA I
Mode selection terminal (fixed at “H”)
38 MODB I
Mode selection terminal (fixed at “L”)
39 MODC I
Mode selection terminal (fixed at “H”)
40 SVCC
Power supply terminal (+5V) (for serial port)
41 MOSI O
Communication data output to the master controller (IC3413)
42 SS I
SPI slave select signal input from the master controller (IC3413)
43 HREQ I
Host request signal input from the master controller (IC3413)
44 SGND
Ground terminal (for serial port)
45 SDO2 O
Audio serial data output terminal Not used (open)
Address signal output to the external RAM device Not used (open)
Address signal output to the external RAM device Not used (open)
– 15 –
Pin No. Pin Name I/O Function
46 SDO1 O 47 SDO0 O 48 SVCC — 49 SCKT O 50 WST O 51 SCKR I 52 QGND — 53 QVCC — 54 55 WSR I 56 SDI1 I 57 SDI0 I 58 DSO O 59 DSI I 60 DSCK I 61 DR I 62 MD7 I/O 63 MD6 I/O 64 MD5 I/O 65 MD4 I/O 66 DGND — 67 MD3 I/O 68 MD2 I/O 69 MD1 I/O 70 DVCC — 71 MD0 I/O 72 DGND — 73 GPIO3 I/O 74 GPIO2 I/O 75 GPIO1 I/O 76 GPIO0 I/O 77 MRD O 78 MWR O 79 MRAS O 80 MCAS O
SGND
Audio serial data output to the digital signal processor (IC3412) Audio serial data output to the digital signal processor (IC3412) Power supply terminal (+5V) (for serial port) Audio serial data transfer clock signal output to the digital signal processor (IC3412) Word transmission output to the digital signal processor (IC3412) Bit clock signal (2.8224 MHz) input terminal Ground terminal (for internal logic) Power supply terminal (+5V) (for internal logic)
Ground terminal (for serial port) L/R sampling clock signal (44.1 kHz) input terminal Audio serial data input terminal Audio serial data input terminal Debug serial data output terminal Not used (open) Debug serial data input terminal Not used (open) Debug serial data reading clock signal input terminal Not used (open) Debug request signal input terminal Not used (fixed at “H”)
Two-way data bus with the external RAM device Not used (open)
Ground terminal (for data bus buffer)
Two-way data bus with the external RAM device Not used (open)
Power supply terminal (+5V) (for data bus buffer) Two-way data bus with the external RAM device Not used (open) Ground terminal (for data bus buffer)
General digital signal processor in/out terminal Not used (open)
Write strobe signal output to the external RAM device Not used (open) Read strobe signal output to the external RAM device Not used (open) Row address strobe signal output to the external RAM device Not used (open) Column address strobe signal output to the external RAM device Not used (open)
– 16 –
DIGITAL BOARD IC3412 SSP424023FJ88 (DIGITAL SIGNAL PROCESSOR)
Pin No. Pin Name I/O Function
1 AGND
Ground terminal (for address bus buffer)
2 MCS0 O
Chip select signal output to the external RAM device Not used (open)
3 MA15 O 4 MA14 O
Address signal output to the S-RAM (IC3411)
5 MA13 O 6 AVCC
Power supply terminal (+5V) (for address bus buffer)
7 MA12 O
Address signal output to the S-RAM (IC3411)
8 AGND
Ground terminal (for address bus buffer)
9 QVCC
Power supply terminal (+5V) (for internal logic)
10 QGND
Ground terminal (for internal logic)
11 MA11 O 12 MA10 O 13 MA9 O 14 MA8 O 15 AGND
Ground terminal (for address bus buffer)
16 MA7 O
Address signal output to the S-RAM (IC3411)
17 AVCC
Power supply terminal (+5V) (for address bus buffer)
18 MA6 O 19 MA5 O
Address signal output to the S-RAM (IC3411)
20 MA4 O 21 AGND
Ground terminal (for address bus buffer)
22 MA3 O 23 MA2 O 24 MA1 O 25 MA0 O 26 SCK I
Serial data reading clock signal input from the master controller (IC3413)
27 EXTAL I
Master clock signal input terminal (3MHz)
28 QVCC
Power supply terminal (+5V) (for internal logic)
29 QGND
Ground terminal (for internal logic)
30 PINIT I
Initialize input for the PLL circuit (fixed at “L”)
31 PGND
Ground terminal (for PLL circuit)
32 PCAP I
Connected to the external capacitor for PLL circuit filter
33 PVCC
Power supply terminal (+5V) (for PLL circuit)
34 SGND
Ground terminal (for serial port)
35 MISO I
Communication data input from the master controller (IC3413)
36 RESET I
Reset signal input from the master controller (IC3413) “L”: reset
37 MODA I
Mode selection terminal (fixed at “H”)
38 MODB I
Mode selection terminal (fixed at “L”)
39 MODC I
Mode selection terminal (fixed at “H”)
40 SVCC
Power supply terminal (+5V) (for serial port)
41 MOSI O
Communication data output to the master controller (IC3413)
42 SS I
SPI slave select signal input from the master controller (IC3413)
43 HREQ I
Host request signal input from the master controller (IC3413)
44 SGND
Ground terminal (for serial port)
45 SDO2 O
Audio serial data output terminal (for rear side speaker)
Address signal output to the S-RAM (IC3411)
Address signal output to the S-RAM (IC3411)
– 17 –
Pin No. Pin Name I/O Function
46 SDO1 O 47 SDO0 O 48 SVCC — 49 SCKT I 50 WST I 51 SCKR I 52 QGND — 53 QVCC — 54 55 WSR I 56 SDI1 I 57 SDI0 I 58 DSO O 59 DSI I 60 DSCK I 61 DR I 62 MD7 I/O 63 MD6 I/O 64 MD5 I/O 65 MD4 I/O 66 DGND — 67 MD3 I/O 68 MD2 I/O 69 MD1 I/O 70 DVCC — 71 MD0 I/O 72 DGND — 73 GPIO3 I/O 74 GPIO2 I/O 75 GPIO1 I/O 76 GPIO0 I/O 77 MRD O 78 MWR O 79 CS1 O 80 MA16 O
SGND
Audio serial data output terminal (for center side speaker) Audio serial data output terminal (for front side speaker) Power supply terminal (+5V) (for serial port) Bit clock signal (2.8224 MHz) input terminal L/R sampling clock signal (44.1 kHz) input terminal Audio serial data reading clock signal input from the digital signal processor (IC3410) Ground terminal (for internal logic) Power supply terminal (+5V) (for internal logic)
Ground terminal (for serial port) Word transmission input from the digital signal processor (IC3410) Audio serial data input from the digital signal processor (IC3410) Audio serial data input from the digital signal processor (IC3410) Debug serial data output terminal Not used (open) Debug serial data input terminal Not used (open) Debug serial data reading clock signal input terminal Not used (open) Debug request signal input terminal Not used (fixed at “H”)
Two-way data bus with the S-RAM (IC3411)
Ground terminal (for data bus buffer)
Two-way data bus with the S-RAM (IC3411)
Power supply terminal (+5V) (for data bus buffer) Two-way data bus with the S-RAM (IC3411) Ground terminal (for data bus buffer)
General digital signal processor in/out terminal Not used (open)
General digital signal processor in/out with the master controller (IC3413) Write strobe signal output to the S-RAM (IC3411) Read strobe signal output to the S-RAM (IC3411) Chip select signal output to the external RAM device Not used (open) Address signal output to the S-RAM (IC3411)
– 18 –
Loading...
+ 40 hidden pages