Sony MKS-8010A, MKS-8011A Operation Manual

CENTER CONTROL PANEL PACK

CCP-8000

MKS-8010A MKS-8011A MKS-8013A MKS-8014A MKS-8015A MKS-8017A MKS-8018A MKS-8019A MKS-8020A MKS-8021A MKS-8021ASC MKS-8022A MKS-8022ASC MKS-8023A MKS-8023AB MKS-8024A MKS-8025MS MKS-8026A MKS-8027A MKS-8028A MKS-8030A MKS-8031AJS MKS-8031ATB MKS-8032A MKS-8033A MKS-8034ADK MKS-8034AFB MKS-8035A MKS-8036A MKS-8040 MKS-8041 MKS-8042 MKS-8075A MKS-8076 HK-PSU02

OPERATION MANUAL [English] 2nd Edition (Revised 3)

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

WARNING: THIS WARNING IS APPLICABLE FOR USA

ONLY. If used in USA, use the UL LISTED power cord specified below. DO NOT USE ANY OTHER POWER CORD.

Plug Cap Parallel blade with ground pin

(NEMA 5-15P Configuration) Cord Type SJT, three 16 or 18 AWG wires Length Minimum 1.5 m (4 ft 11 in), Less than 2.5 m

(8 ft 3 in) Rating Minimum 10 A, 125 V

THIS APPARATUS MUST BE EARTHED.

For the customers in the USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

(Except for HK-PSU02)

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

(HK-PSU02 only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For the customers in Canada (HK-PSU02 only)

This Class A digital apparatus complies with Canadian ICES-

003.

Pour les utilisateurs au Canada (HK-PSU02 uniquement)

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

This symbol is intended to alert the user to the presence of important operrating and maintenance (servicing) instructions in the literature accompanying the appliance.

Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.

1.Use the approved Power Cord (3-core mains lead) /

Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.

2.Use the Power Cord (3-core mains lead) / Appliance

Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

WARNUNG: DIESE WARNUNG GILT FÜR ANDERE LÄNDER.

1.Verwenden Sie Netzkabel (dreiadrig), Geräteanschlüsse

und Netzkabelstecker mit Masseleitung, die den Sicherheitsrichtlinien des jeweiligen Landes entspricht.

2.Verwenden Sie Netzkabel (dreiadrig), Geräteanschlüsse

und Netzkabelstecker mit Masseleitung, die den vor Ort herrschenden Spannungsanforderungen (Spannung, Stromstärke) entsprechen.

Bei Frage über die Eignung und Sicherheit von Netzkabeln (dreiadrig), Geräteanschlüssen und Netzkabelsteckern wenden Sie sich bitte an einen qualifizierten Elektrotechniker.

AVERTISSEMENT: CET AVERTISSEMENT EST VALABLE POUR LES AUTRES PAYS.

1.Utiliser un cordon d’alimentation approuvé (conducteur

d’alimentation 3 âmes)/connecteur d’appareil/prise avec contacts de mise à la terre conforme aux règles de sécurité de chaque pays si applicable.

2.Utiliser un cordon d’alimentation approuvé (conducteur

d’alimentation 3 âmes)/connecteur d’appareil/prise conforme aux valeurs nominales (tension, ampérage) correctes.

S’adresser à un personnel de service qualifié pour toute question concernant l’emploi du cordon d’alimentation/ connecteur d’appareil/prise ci-dessus.

WARNUNG

Um die Gefahr von Bränden oder elektrischen Schlägen zu verringern, darf dieses Gerät nicht Regen oder Feuchtigkeit ausgesetzt werden. Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal.

DIESES GERÄT MUSS GEERDET WERDEN.

AVERTISSEMENT

Afin de réduire les risques d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.

CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE.

For the customers in Europe (MKS-8010A only)

This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/ EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European standards:

• EN60950-1: Product Safety

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio).

Pour les clients européens (MKS-8010A uniquement)

Ce produit portant la marque CE est conforme à la fois à la Directive sur la compatibilité électromagnétique (EMC) (89/ 336/CEE) et à la Directive sur les basses tensions (73/23/ CEE) émises par la Commission de la Communauté européenne. La conformité à ces directives implique la conformité aux normes européennes suivantes:

• EN60950-1: Sécurité des produits

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité) Ce produit est prévu pour être utilisé dans l’environnement électromagnétique suivant: E4 (environnement EMC contrôlé ex. studio de télévision).

For the customers in Europe (MKS-8011A/8013A/8014A/ 8015A/8017A/8018A/8019A/8020A/8021A/8021ASC/ 8022A/8022ASC/8023A/8023AB/8024A/8025MS/8026A/ 8027A/8028A/8030A/8031AJS/8031ATB/8032A/8033A/ 8034ADK/8034AFB/8035A/8036A/8040/8041/8075A/8076 only)

This product with the CE marking complies with the EMC Directive (89/336/EEC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards:

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio).

Für Kunden in Europa (nur MKS-8011A/8013A/8014A/ 8015A/8017A/8018A/8019A/8020A/8021A/8021ASC/ 8022A/8022ASC/8023A/8023AB/8024A/8025MS/8026A/ 8027A/8028A/8030A/8031AJS/8031ATB/8032A/8033A/ 8034ADK/8034AFB/8035A/8036A/8040/8041/8075A/8076)

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie (89/336/EWG) der EG-Kommission. Angewandte Normen:

• EN55103-1: Elektromagnetische Verträglichkeit

(Störaussendung)

• EN55103-2: Elektromagnetische Verträglichkeit

(Störfestigkeit), für die folgenden elektromagnetischen Umgebungen: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio).

Für Kunden in Europa (nur MKS-8010A)

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie (89/336/EWG) sowie die Niederspannungsrichtlinie (73/23/EWG) der EG-Kommission. Angewandte Normen:

• EN60950-1: Sicherheitsbestimmungen

• EN55103-1: Elektromagnetische Verträglichkeit (Störaussendung)

• EN55103-2: Elektromagnetische Verträglichkeit (Störfestigkeit),

für die folgenden elektromagnetischen Umgebungen: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio)

Pour les clients européens (MKS-8011A/8013A/8014A/ 8015A/8017A/8018A/8019A/8020A/8021A/8021ASC/ 8022A/8022ASC/8023A/8023AB/8024A/8025MS/8026A/ 8027A/8028A/8030A/8031AJS/8031ATB/8032A/8033A/ 8034ADK/8034AFB/8035A/8036A/8040/8041/8075A/8076 uniquement)

Ce produit portant la marque CE est conforme à la Directive sur la compatibilité électromagnétique (EMC) (89/336/CEE) émise par la Commission de la Communauté européenne. La conformité à cette directive implique la conformité aux normes européennes suivantes:

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans l’environnement électromagnétique suivant: E4 (environnement EMC contrôlé ex. studio de télévision).

Für Kunden in Deutschland (nur MKS-8010A)

Wenn Sie das Gerät entsorgen wollen, wenden Sie sich bitte an das nächste Sony-Kundendienstzentrum. Der eingebaute Akku muß als chemischer Sondermüll entsorgt werden.

For the customers in Europe (HK-PSU02 only)

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following Electromagnetic Environment(s): E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors) and E4 (controlled EMC environment, ex. TV studio).

Für Kunden in Europa (nur HK-PSU02)

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie (89/336/EWG) der EG-Kommission. Angewandte Normen:

• EN55103-1: Elektromagnetische Verträglichkeit (Störaussendung)

• EN55103-2: Elektromagnetische Verträglichkeit (Störfestigkeit),

für die folgenden elektromagnetischen Umgebungen: E1 (Wohnbereich), E2 (kommerzieller und in beschränktem Maße industrieller Bereich), E3 (Stadtbereich im Freien) und E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio).

For Customers in Taiwan only (MKS-8010A only)

For the customers in the USA (MKS-8011A only)

This product (fluorescent lamp in the liquid crystal display) contains mercury. Disposal of this product may be regulated if sold in the United States. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance (www.eiae.org http://www.eiae.org)

For the State of California, USA only (MKS-8010A only)

Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material : Lithium battery contains perchlorate.

Pour les clients européens (HK-PSU02 seulement)

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans les environnements électromagnétiques suivants: E1 (résidentiel), E2 (commercial et industrie légère), E3 (urbain extérieur) et E4 (environnement EMC contrôlé, ex. studio de télévision).

Periodic inspections

To guarantee safe long-term operation, periodic inspections are recommended. Please contact your Sony representative for detailed information about the content and cost of periodic inspections.

Overview ............................................................................... 7

Features......................................................................................7

Units and Modules..................................................................... 7

Optional Accessories ................................................................. 9

Location and Function of Parts.........................................10

MKS-8010A Front Panel........................................................ 10

MKS-8010A Rear Panel ......................................................... 11

MKS-8011A Menu Panel ....................................................... 13

Main Panel .............................................................................. 13

AUX Panel.............................................................................. 14

MKS-8025MS “Memory Stick”/USB Module....................... 14

MKS-8075A Extension Adaptor ............................................ 15

MKS-8076 Memory Card/USB Adaptor................................ 15

Example System Configuration ........................................16

MVS-8000A System Configuration ....................................... 16

Center Control Panel Connection ........................................... 17

Exchanging Button Labels ................................................18

Adjusting Fader Torque..................................................... 19

Power Supply Unit Status Indicators................................ 19

Care of the Control Panel ..................................................20

About a “Memory Stick” ....................................................20

What Is “Memory Stick”? .......................................................20

Types of “Memory Stick”........................................................ 20

Available Types of “Memory Stick” .......................................21

Note on “Memory Stick PRO” ................................................ 21

Notes on “Memory Stick Duo”................................................21

Before Using a “Memory Stick”..............................................21

About Formatting “Memory Stick” ......................................... 21

Caution When Formatting “Memory Stick” on a Personal

Computer........................................................................22

When the Status Indicator Is Lit or Flashing ...........................22

Precautions............................................................................... 22

Specifications..................................................................... 22

Center Control Panel................................................................22

Main Panel ............................................................................... 22

AUX panel ...............................................................................23

MKS-8010A System Control Unit .......................................... 23

MKS-8011A Menu Panel ........................................................24

MKS-8013A 32 AUX Bus Module .........................................24

MKS-8014A 24 AUX Bus Module .........................................24

MKS-8015A 16 AUX Bus Module .........................................24

MKS-8017A 32 XPT Module .................................................25

Table of Contents

MKS-8018A 24 XPT Module .................................................25

MKS-8019A 16 XPT Module .................................................25

MKS-8020A Standard Transition Module .............................. 25

MKS-8021A Simple Transition Right Module ....................... 25

MKS-8021ASC Simple Transition Compact Right Module... 25

MKS-8022A Simple Transition Left Module..........................25

MKS-8022ASC Simple Transition Compact Left Module .....26

MKS-8023A Compact Key Transition Module ......................26

MKS-8023AB Compact Key Transition Module.................... 26

MKS-8024A Flexi Pad Module............................................... 26

MKS-8025MS “Memory Stick”/USB Module........................ 26

MKS-8026A 10 Key Pad Module ...........................................26

MKS-8027A Compact Transition Right Module ....................26

MKS-8028A Compact Transition Left Module ......................27

MKS-8030A Key Frame Module ............................................27

MKS-8031AJS Joystick Module .............................................27

MKS-8031ATB Track Ball Module........................................ 27

MKS-8032A DSK Fader Module............................................ 27

MKS-8033A Utility/Shotbox Module .....................................27

MKS-8034ADK DSK/FTB Module........................................27

MKS-8034AFB FTB Module.................................................. 27

MKS-8035A Key Control Module ..........................................28

MKS-8036A Device Control Module .....................................28

MKS-8040 Blank Panel (1/3) ..................................................28

MKS-8041 Blank Panel (1/2) ..................................................28

MKS-8042 Blank Panel (1/6) ..................................................28

MKS-8075A Extension Adaptor .............................................28

MKS-8076 Memory Card/USB Adaptor.................................29

HK-PSU02 Power Supply Unit ............................................... 29

Table of Contents

Overview

The CCP-8000 Center Control Panel Pack provides control panels for operation of a MVS-8000 Multi Format Switcher system. It has a wide range of application, being usable in studios and the ENG and OB vans of large-scale live production systems as well as in postproduction editing systems. “Center control panel” refers to the control panel as a whole, which is comprised of the following three elements.

Main Panel

The main panel, comprised of various types of operation modules, provides the operating controls of the system. It can be freely laid out, with variable numbers of M/E banks (2 to 4) and cross-point buttons (24 or 32) and variable layout of the auxiliary bus module. Operation modules can be mounted in the MKS-8075A Extension Adaptor and MKS-8076 Memory Card/USB Adaptor for installation apart from the main panel. The auxiliary bus module can also be removed from the main panel and used as an AUX panel.

Menu Panel

The menu panel provides a GUI interface for making system settings.

Special features for mid- and large-scale live switcher systems

The center control panel was designed with many features for live operation, such as shotbox functions, source name display on cross-point buttons, the ability to recall snapshots and other effect memory settings directly on the Flexi Pad

, and redundant power supply.

Powerful external device control

The center control panel can control devices such as Sony routing switchers and IF processors. Control of devices such as VTRs and DDRs can be linked to timelines of switchers and DME.

Generous storage capacity

The center control panel has an internal hard disk drive for storage of settings and still pictures from switcher frame memory. They can also be storage to “Memory Sticks” and other memory cards.

Units and Modules

MKS-8010A System Control Unit

A system control unit to provide control functions for the center control panel as a whole and supply power to the various panels.

System Control Unit

The system control unit provides control functions for the center control panel as a whole. It also supplies power to the various panels.

Features

Free control panel layout

The modular configuration of the center control panel allows operation modules to be freely laid out in the way that best meets your requirements.

Intuitive, easy-to-use man-machine interface

The Flexi PadTM and shotbox sections feature LCD display buttons that can display the names of registered effects or graphics for registered patterns. Registered effects are evident at a glance, a significant advantage in live situations where decisions must be made instantly. The menu control block features a large, touch-sensitive LCD panel for speedy menu operations.

MKS-8011A Menu Panel

A menu operation panel equipped with a 10.4-inch color LCD touch screen.

MKS-8013A 32 AUX Bus Module

An auxiliary bus control module with 32 cross-point buttons.

MKS-8014A 24 AUX Bus Module

An auxiliary bus control module with 24 cross-point buttons.

MKS-8015A 16 AUX Bus Module

An auxiliary bus control module with 16 cross-point buttons.

MKS-8017A 32 XPT Module

An M/E or PGM/PST bank cross-point module with 32 cross-point buttons.

Overview

MKS-8018A 24 XPT Module

An M/E or PGM/PST bank cross-point module with 24 cross-point buttons.

MKS-8019A 16 XPT Module

An M/E or PGM/PST bank cross-point module with 16 cross-point buttons.

MKS-8020A Standard Transition Module

A transition operation module for an M/E bank or the PGM/PST bank. Comprised of a transition operation section and a key transition operation section.

MKS-8021A Simple Transition Right Module

A transition operation module for an M/E bank or the PGM/PST bank. Comprised of a transition operation section with a split fader and a Flexi Pad section. The fader lever is at a different position than on the MKS-8022A.

MKS-8021ASC Simple Transition Compact Right Module

MKS-8022A Simple Transition Left Module

A transition operation module for an M/E bank or the PGM/PST banks. Comprised of a transition operation section with a split fader and a Flexi Pad section. The fader lever is at a different position than on the MKS-8021A.

MKS-8022ASC Simple Transition Compact Left Module

MKS-8023AB Compact Key Transition Module

A key transition operation module for 2/4-keyer transitions. Used in combination with the MKS-8021A/ 8021ASC/8022A/8022ASC.

MKS-8024A Flexi Pad Module

An operation module for Flexi Pad operations. Used in combination with the MKS-8020A.

MKS-8025MS “Memory Stick”/USB Module

A module equipped with a “Memory Stick” slot and three DEVICE connectors.

MKS-8026A 10 Key Pad Module

A numeric keypad module.

MKS-8027A Compact Transition Right Module

A transition operation module for an M/E bank or the PGM/PST bank. Features a simple key transition operation section. A compact module that fits in 1/2 rack width.

MKS-8028A Compact Transition Left Module

Identical to the MKS-8027A, but with the fader lever on the left side.

MKS-8030A Key Frame Module

A module for key frame operations.

MKS-8031AJS Joystick Module

A module for DME operations using a joystick and for switcher wipe positioner operations.

MKS-8031ATB Track Ball Module

A module for DME operations using a track ball and for switcher wipe positioner operations.

MKS-8023A Compact Key Transition Module

A key transition operation module for 2-keyer transitions. Used in combination with the MKS-8021A or MKS8022A.

Overview

MKS-8032A DSK Fader Module

An operation module for fader lever operations on four downstream keys.

MKS-8033A Utility/Shotbox Module

An operation module to provide buttons that may be used as utility buttons or shotbox recall buttons.

MKS-8034ADK DSK/FTB Module

An operation module for operations on two downstream keys and for fade to black and preview selector operations. (This module is the MKS-8034AFB module with the addition of controls for DSK operations.)

MKS-8034AFB FTB Module

An operation module for fade to black and preview selector operations.

MKS-8035A Key Control Module

An operation module for key adjustments and other operations.

MKS-8036A Device Control Module

An operation module for disk recorder/VTR control operations.

MKS-8040 Blank Panel (1/3)

A blank panel to fill parts of the main panel which are not filled by the modules in its current configuration.

SWC-5005 50-pin Panel Cable (5 m/16 ft) SWC-5010 50-pin Panel Cable (10 m/33 ft) RMM-10 Rack Mount Kit

MKS-8041 Blank Panel (1/2)

A blank panel to fill parts of the main panel which are not filled by the modules in its current configuration.

MKS-8042 Blank Panel (1/6)

A blank panel to fill parts of the main panel which are not filled by the modules in its current configuration.

MKS-8075A Extension Adaptor

An adaptor which allows modules to be installed apart from the main panel.

MKS-8076 Memory Card/USB Adaptor

An adaptor that allows the MKS-8025MS to be installed apart from the main panel.

HK-PSU02 Power Supply Unit (on MKS8010A)

A backup power supply unit. The MKS-8010A is supplied standard with one power unit. Installing an HK-PSU02 gives two power units. This allows a backup system to be constructed which will operate normally even if one of the power supply units fails.

Optional Accessories

SWC-5002 50-pin Panel Cable (2 m/7 ft)

Overview

Location and Function of Parts

MKS-8010A Front Panel

POWER A POWER B

POWER B switch and status indicator

POWER A switch and status indicator

POWER A and B switches and status indicators

The POWER switches turn the unit on and off. The unit is powered on when the POWER switches are on the “?” side, and powered off when the POWER switches are on the “a” side. The status indicators light in green when the unit is powered on. Depending on the configuration of your unit, an optional Backup Power Supply Unit may not be installed. In this case, there is no POWER B switch indicator.

Caution

Before installing an optional Backup Power Supply Unit in your unit, be sure to contact your Sony service representative.

Note

If a status indicator does not light when you turn a POWER switch on, there may be a fault in the power circuits. Turn the POWER switch off and contact your Sony service representative.

Location and Function of Parts

+ 22 hidden pages

Sony MKS-8010A, MKS-8011A Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Overview

Units and Modules

Features

Optional Accessories

Location and Function of Parts

MKS-8010A Front Panel