Sony HK-PSU04, MKE-9020M, MVE-9000-C, MVE-9000, MKE-9040M User Manual
...
DME PROCESSOR PACK
MVE-9000-C
MULTI FORMAT DME PROCESSOR
MVE-9000
HK-PSU04
MKE-9020M
MKE-9021M
MKE-9040M
INSTALLATION MANUAL
1st Edition
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin de
réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les
réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres.
Pour toute réparation faire appel à une personne compétente uniquement.
MVE-9000 Serial No. 10001 and Higher
HK-PSU04 Serial No. 10001 and Higher
MKE-9020M Serial No. 10001 and Higher
MKE-9021M Serial No. 10001 and Higher
MKE-9040M Serial No. 10001 and Higher
MVE-9000 IM
For MVE-9000
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the rear of
the unit 10 cm (4 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.
For MVE-9000
When using a LAN cable:
For safety,do not connect to the connector for
peripheral device wiring that might have excessive
voltage.
MVE-9000 IM
1 (P)
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 2
Related manuals......................................................................................................... 2
Contents ..................................................................................................................... 2
Trademark .................................................................................................................. 2
1. Installation
1-1. Operating Environment ...............................................................................1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Specifications ..................................................................1-1
1-2-2. Recommended Power Cord ........................................................ 1-2
1-3. Installation Space (External dimensions) .................................................... 1-3
1-4. Installing the Options .................................................................................. 1-4
1-4-1. Installing the Plug-in Boards ...................................................... 1-4
1-4-2. Installing the Connector Board ..................................................1-6
1-4-3. Installing the HK-PSU04 ...........................................................1-7
1-5. Rack Mounting ............................................................................................ 1-8
1-6. Matching Connectors and Cables.............................................................. 1-10
1-7. Input/Output Signals of Connectors .......................................................... 1-11
1-8. Checks on Completion of Installation ....................................................... 1-12
1-8-1. On-board Switches Setting and LED Functions ......................1-12
1-9. System Connection.................................................................................... 1-22
MVE-9000 IM
2. Service Overview
2-1. Troubleshooting .......................................................................................... 2-1
2-2. Periodic Inspection and Maintenance ......................................................... 2-2
2-2-1. Cleaning .....................................................................................2-2
2-3. About the Data Backup Capacitor ............................................................... 2-2
1
Purpose of this manual
Related manuals
Manual Structure
This manual is the installation manual of DME Processor Pack MVE-9000-C and
their optional boards and units.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the MVE-9000-C system.
The following manuals are prepared for MVE-9000-C and their optional boards and
units.
..
. Operation Manual (Supplied with MVE-9000-C)
..
This manual describes the application and operation of MVE-9000-C system.
..
. Maintenance Manual (Available on request)
..
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
Trademark
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space,
installation of optional boards and units, rack mounting, connectors, input and
output signals of connectors, checking upon completion of installation, and system
configuration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
Registered trademark used in this manual is follows.
. Ethernet is a registered trademark of Xerox Corporation.
2
MVE-9000 IM
Section 1
Installation
1-1. Operating Environment
Operating guaranteed temperature : +5 dC to +40 dC
Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC
Mass (when all options are installed) : Approx. 27 kg
Prohibited locations for installation
. Areas where the unit will be exposed do direct sunlight
or any other strong lights.
. Dusty areas
. Areas subject to vibration.
. Areas with strong electric or magnetic fields.
. Areas near heat sources.
. Areas subject to electrical noise.
. Areas subject where is subjected to static electricity.
Ventilation
The inside of the MVE-9000-C is cooled by a fan (both
sides).
The power supply can be damaged if the exhaust vent
(both sides) and air intake (front panel) are blocked or the
fan is stopped.
Therefore, leave a blank space of more than 10 cm in the
front and both sides of the MVE-9000-C.
1-2. Power Supply
1-2-1. Power Specifications
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
Power requirements : AC 100 to 240 V ± 10 %
Power frequency : 50/60 Hz
Current consumption (when all options are installed) :
6.0 to 2.5 A
m
. As the inrush current at turn-on is a maximum 110 A (at
100 V)/220 A (at 240 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will
abnormally operate.
. The MVE-9000 contains the single power supply unit as
the standard configuration. A maximum of two power
supply units may be installed. When starting up the
MVE-9000, be sure to turn on the power of one or more
power supply units.
MVE-9000 IM
1-1
1-2-2. Recommended Power Cord
This unit does not come with a power cord.
To get a power cord, please contact your local Sony Sales
Office/Service Center.
w
. Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please contact your local Sony
Sales Office/Service Center.
w
. Never use an injured power cord.
. Plugging the power cord in the AC inlet, push as far as it
will go.
For customers in the U.S.A. and Canada
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11
1
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-21
1
AC inlet
AC inlet
1-2
MVE-9000 IM
1-3. Installation Space (External dimensions)
520
7
35
482
465
440
375
37.2
101.6
176(4U)
17.5
161
144.5 115.5 115.5
61
380
Unit : mm
MVE-9000 IM
1-3
1-4. Installing the Options
The MVE-9000-C is shipped from the factory with the
necessary option (refer to the following table) already
installed in the MVE-9000, in accordance with the specified system configuration.
Installation procedure
1. Turn off the main power of the MVE-9000 and
disconnect the AC power cord from the wall outlet.
2. Loosen the four screws (with drop-safe) and remove
the front panel in the direction of the arrow.
MVE-9000-C options
Model name Board configuration
Plug-in board Connector board
MKE-9020M _ CN-2357A board
MVS Interface Board Set CN-2357B board
MKE-9021M _ CN-2355A board
Input/Output Board Set CN-2355B board
MKE-9040M DVP-24A board
Advanced Effects Board
HK-PSU04 __
Power Supply Unit
1-4-1. Installing the Plug-in Boards
c
Be sure to turn off the POWER switch and unplug the
power cord from the wall outlet before starting the installation work.
If the installation work is started with the POWER switch
left on, it may cause electrical shock or damage of printed
circuit boards.
Screws
(with drop-safe)
Front panel
Screws
(with drop-safe)
3. Remove the four screws (B3 x 5), and remove the
“plug-in board loose-proof assembly”.
1-4
B3 x 5
Plug-in board
loose-proof assembly
B3 x 5
MVE-9000 IM
4. While the eject levers are kept open as shown in the
illustration, insert the plug-in board into the board
guide rails.
5. While closing the eject levers in the direction of arrow
1, push in the plug-in board.
Eject levers
Name of option Name of board Slot on the front side
MKE-9040M DVP-24A board*13, 4, 5, 6
*1 : The DVP-24A boards are assigned to the following channels in
accordance with the slots to which the boards are inserted.
Slot Channel
3 CH1
4 CH2
5 CH3
6 CH4
1
Eject lever Eject lever
1
6. Attach the plug-in board loose-proof assembly and the
front panel by reversing the installation steps 2, 3.
MVE-9000 IM
1-5
Loading...