Sony MVE-8000A, MVE-8000A-C, MKE-8020A, HK-PSU02 User Manual

DME PROCESSOR PACK
MVE-8000A-C
MULTI FORMAT DME PROCESSOR
MVE-8000A
HK-PSU02
MKE-8020A
MKE-8040A
INSTALLATION MANUAL 1st Edition
! WARNING
This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin de réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres. Pour toute réparation faire appel à une personne compétente uniquement.
MVE-8000A Serial No. 10001 and Higher HK-PSU02 Serial No. 10001 and Higher MKE-8020A Serial No. 10001 and Higher MKE-8040A Serial No. 10001 and Higher
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.
2. Providing protective earth
When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.
4. Prevention against achieving hazardous condition due to uneven mechanical loading
When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading.
5. Install the equipment while taking the operating temperature of the equipment into consideration
For the operating temperature of the equipment, refer to the specifications of the Operation Manual.
6. When performing the installation, keep the following space away from walls in order to obtain proper exhaust and radiation of heat.
Rear: 10 cm (4 inches) or more Right, Left: 4 cm (1.6 inches) or more
For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to the following port(s). : DATA connector : CTRL connector Follow the instructions for the above port(s).
MVE-8000A
1 (P)

Table of Contents

Manual Structure
Purpose of this manual .............................................................................................. 2
Related manuals......................................................................................................... 2
Contents ..................................................................................................................... 2
Trademark.................................................................................................................. 2
1. Installation
1-1. Operating Environment ............................................................................... 1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Specifications ..................................................................1-1
1-2-2. Recommended Power Cord........................................................1-2
1-3. Installation Space (External dimensions).................................................... 1-3
1-4. Installing the Options ..................................................................................1-4
1-4-1. Installing the Plug-in Boards......................................................1-4
1-4-2. Installing the Connector Board ..................................................1-6
1-4-3. Installing the HK-PSU02 ...........................................................1-7
1-5. Rack Mounting............................................................................................1-9
1-6. Matching Connectors and Cables..............................................................1-11
1-7. Input/Output Signals of Connectors..........................................................1-12
1-8. Checks on Completion of Installation.......................................................1-13
1-8-1. On-board Switches Setting and LED Functions ......................1-13
1-9. System Connection....................................................................................1-22
MVE-8000A
2. Service Overview
2-1. Troubleshooting ..........................................................................................2-1
2-2. Periodic Inspection and Maintenance .........................................................2-2
2-2-1. Cleaning .....................................................................................2-2
2-3. About the Data Backup Capacitor...............................................................2-2
1

Purpose of this manual

Related manuals

Manual Structure

This manual is the installation manual of DME Processor Pack MVE-8000A-C and their optional boards and units. This manual is intended for use by trained system and service engineers, and describes the information on installing the MVE-8000A-C system.
The following manuals are prepared for MVE-8000A-C and their optional boards and units.
..
. Operation Manual (Supplied with MVE-8000A-C)
..
This manual describes the application and operation of MVE-8000A-C system.
..
. Maintenance Manual (Available on request)
..
This manual describes the detailed service information. If this manual is required, please contact your local Sony Sales Office/Service Center.

Contents

Trademark

This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space, installation of optional boards and units, rack mounting, connectors, input and output signals of connectors, checking upon completion of installation, and system configuration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
Registered trademark used in this manual is follows.
. Ethernet is a registered trademark of Xerox Corporation.
2
MVE-8000A
Section 1

Installation

1-1. Operating Environment

Operating guaranteed temperature : +5 dC to +40 dC Performance guaranteed temperature : +10 dC to +35 dC Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC Mass (when all options are installed) : Approx. 16.5 kg
Prohibited locations for installation
. Areas where the unit will be exposed do direct sunlight
or any other strong lights.
. Dusty areas . Areas subject to vibration. . Areas with strong electric or magnetic fields. . Areas near heat sources. . Areas subject to electrical noise. . Areas subject where is subjected to static electricity.
Ventilation
The inside of the MVE-8000A-C is cooled by a fan (both sides). The power supply can be damaged if the exhaust vent (both sides) and air intake (front panel) are blocked or the fan is stopped. Therefore, leave a blank space of more than 10 cm in the front and both sides of the MVE-8000A-C.

1-2. Power Supply

1-2-1. Power Specifications

A switching regulator is used for the power supply of this unit. The voltage within the range of 100 V to 240 V can be used without changing the supply voltage.
Power requirements : AC 100 to 240 V Power frequency : 50/60 Hz Current consumption (when all options are installed) :
2.8 to 1.2 A
m . As the inrush current at turn-on is a maximum 14 A (at
100 V)/66 A (at 240 V), the capacity of the AC power source must be commensurate with this load. If the capacity of the AC power is not adequately large, the AC power source braker will operate or the unit will abnormally operate.
. The MVE-8000A contains the single power supply unit
as the standard configuration. A maximum of two power supply units may be installed. When starting up the MVE-8000A, be sure to turn on the power of one or more power supply units.
MVE-8000A
1-1

1-2-2. Recommended Power Cord

This unit does not come with a power cord. To get a power cord, please contact your local Sony Sales Office/Service Center.
w . Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Volt­age, Ampere).
If you have questions on the use of the above Power Cord/ Appliance Connector/Plug, please contact your local Sony Sales Office/Service Center.
w . Never use an injured power cord. . Plugging the power cord in the AC inlet, push as far as it
will go.
For customers in the U.S.A. and Canada
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11
1
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-12
1
AC inlet
AC inlet
1-2
MVE-8000A

1-3. Installation Space (External dimensions)

440
MULTI FORMAT DME PROCESSOR
MVE-8000A
520
380
7
26Ø
61
35
MVE-8000A
375
482
87.517.5
105
Unit : mm
1-3

1-4. Installing the Options

1-4-1. Installing the Plug-in Boards

The MVE-8000A-C is shipped from the factory with the necessary option (refer to the following table) already installed in the MVE-8000A, in accordance with the specified system configuration.
MVE-8000A-C options
Model name Board configuration
Plug-in board Connector board
MKE-8020A _ CN-2153 board MVS Interface Board
MKE-8040A DVP-30A board Advanced Effects Board
HK-PSU02 __ Power Supply Unit
c
Be sure to turn off the POWER switch and unplug the power cord from the wall outlet before starting the installa­tion work. If the installation work is started with the POWER switch left on, it may cause electrical shock or damage of printed circuit boards.
Installation procedure
1. Turn off the main power of the MVE-8000A and disconnect the AC power cord from the wall outlet.
2. Loosen the four screws (with drop-safe) and remove the front door assembly in the direction of the arrow.
Screws (with drop-safe)
Front door assembly
Screws (with drop-safe)
3. Remove the four screws (B3 x 5), and remove the “plug-in board loose-proof assembly”.
B3 x 5
Plug-in board loose-proof assembly
1-4
B3 x 5
MVE-8000A
4. While the eject levers are kept open as shown in the illustration, insert the plug-in board into the board guide rails.
5. While closing the eject levers in the direction of arrow, push in the plug-in board.
Eject lever
Plug-in board
Plug-in board
Eject levers
Name of option Name of board Slot on the front side
MKE-8040A DVP-30A board*12, 3
*1 : The DVP-30A boards are assigned to the following channels in
accordance with the slots to which the boards are inserted.
Slot Channel
2 CH1, CH2 3 CH3, CH4
Eject lever
Plug-in board
6. Attach the plug-in board loose-proof assembly and the front door assembly by reversing the installation steps 2, 3.
MVE-8000A
1-5
Loading...
+ 23 hidden pages