Sony LBT-XB3S Users guide

Compact Hi-Fi Stereo System
Operating Instructions
3-859-895-11(1)
LBT-XB3S LBT-XB4KS
©1997 by Sony Corporation
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
This caution label is located inside the unit.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
This stereo system is equipped with the Dolby* B­type noise reduction system.
* Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol a are trademarks of the Dolby Laboratories Licensing Corporation.
2
Table of Contents
Getting Started
Step 1: Hooking up the system ............ 4
Step 2: Setting the time ......................... 6
Step 3: Presetting radio stations .......... 7
Connecting optional AV
components ...................................... 8
Basic Operations
Playing a CD ......................................... 10
Recording a CD .................................... 12
Listening to the radio........................... 13
Recording from the radio .................... 14
Playing a tape........................................ 15
Recording from a tape ......................... 17
The CD Player
Using the CD display........................... 18
Playing CD tracks repeatedly ............. 18
Playing CD tracks in random
order ................................................ 19
Programming CD tracks ..................... 20
Playing CDs without interruption ..... 21
Sound Adjustment
Adjusting the sound ............................ 27
Selecting the audio emphasis ............. 28
Adjusting the audio emphasis............ 29
Making a personal audio emphasis
file .................................................... 30
Other Features
Singing along: Karaoke ...................... 31
Falling asleep to music ........................ 33
Waking up to music ............................. 34
Timer-recording radio programs ....... 35
Additional Information
Precautions ............................................ 37
Troubleshooting ................................... 38
Specifications ........................................ 40
Index....................................................... 42
F ES
P
The Tape Deck
Recording on a tape manually ........... 22
Recording CDs by specifying the track
order ................................................ 23
DJ Effects
Looping part of a CD ........................... 25
Flashing part of a CD........................... 25
Waving the equalizer........................... 26
3
Getting Started
Step 1: Hooking up the system
Follow steps 1 through 4 to hook up your system using the supplied cords and accessories.
AM loop antenna
FM antenna
1
The above illustration is of the LBT-XB4KS.
1 Connect the speakers.
1 Connect the speaker cords to
SPEAKER jacks of the same color. Keep the speaker cords away from the
antennas to prevent noise.
R
+
Left speakerRight speaker
4
2
1
1
2 Insert only the stripped portion of the
Note
The speakers for LBT-XB3S do not have the speaker jacks.
L
+ –
Connect the speaker cords to the speaker jacks on the unit.
3
cord. Inserting the vinyl portion will interfere with the speaker connection and no sound will come from the speaker.
Black (’)Red (‘)
4
2 Connect the FM/AM antennas.
Set up the AM loop antenna, then connect it.
Extend the FM wire
AM loop antenna
antenna horizontally.
FM75
AM
3 Connect the power cord to a wall
outlet.
The demonstration appears in the display.
4 Deactivate the demonstration mode
by pressing DISPLAY/DEMO while the system is off.
Inserting two size AA (R6) batteries into the remote
Tips
•With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.
•When you set the time, the demonstration is deactivated.
To activate the demonstration again, press DISPLAY/DEMO while the system is off.
Note
If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage.
When carrying this system
Do the following to protect the CD mechanism.
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Hold down PLAY MODE and press
POWER to turn off the system.
5
Step 2: Setting the time
5 Press ENTER/NEXT.
The clock starts.
You must set the time before using the timer functions.
3,51 2,4
1 Press t/CLOCK SET.
The hour indication flashes.
2 Press TUNING +/– to set the hour.
The clock uses the 12-hour system.
Tip
If you make a mistake, start over from step 1.
3 Press ENTER/NEXT.
The minutes indication flashes.
4 Press TUNING +/– to set the
minutes.
6
Step 3: Presetting radio stations
You can preset up to 30 stations, 20 for FM and 10 for AM.
5 Press TUNING +/– to select the
preset number you want.
DOLBY NR
OFF
TUNED
STEREOAUTO
ALL DISC S
POWER
3,5 1246
1 Press TUNER/BAND repeatedly
until the band you want appears in the display.
Each time you press this button, the band changes as follows:
FM ˜ AM
2 Press TUNING MODE repeatedly
until “AUTO” appears in the display.
3 Press TUNING +/–.
The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear.
DOLBY NR
OFF
TUNED
STEREOAUTO
ALL DISC S
6 Press ENTER/NEXT.
The station is stored.
7 Repeat steps 1 through 6 to store
other stations.
To tune in a station with a weak signal
Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING +/– to tune in the station.
To change the preset number
Start over from step 1.
To change the AM tuning interval
The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To change the AM tuning interval to 10 kHz (or 9 kHz), press TUNER/BAND repeatedly until “AM” appears first, then turn off the system. While holding down ENTER/NEXT, turn the system back on. When you change the interval, the AM preset stations will be erased. To reset the interval, repeat the same procedure.
Note
The preset stations are canceled when you disconnect the power cord or if a power failure occurs for half a day.
MHz
4 Press TUNER MEMORY.
A preset number flashes in the display.
DOLBY NR
OFF
TUNED
STEREOAUTO
ALL DISC S
7
Connecting optional AV components
To enhance your system, you can connect optional components. Refer to the instructions included with each component for details.
Connecting audio components
Connecting a turntable
Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected turntable, press FUNCTION repeatedly until “PHONO” appears.
To the audio output of the turntable
Connecting a VCR
Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected VCR, press FUNCTION repeatedly until “VIDEO” appears.
To the audio output of the VCR
Note
Using the turntable at high volume may cause distortion or howling. This is often caused by the bass sound from the speakers. The bass sound may be picked up by the needle of the turntable, and produce the distortion or howling. To avoid this, do the following:
1Keep some distance between the speakers and the
turntable.
2Stop using the surround effect. 3Install the speakers or the turntable on a firm and
stable surface.
4Press DBFB repeatedly until “DBFB
disappears from the display (LBT-XB3S only). Press SUPER WOOFER repeatedly until the
indicator on this button goes off (LBT-XB4KS only).
8
Connecting outdoor antennas
Connect an outdoor antenna to improve the reception.
FM antenna
Connect an optional FM outdoor antenna. You can also use the TV antenna instead.
75-ohm coaxial cable (not supplied)
FM75
AM
Ground wire (not supplied)
Screw clamp
AM antenna
Connect a 6 to 15 meter (20 to 50 feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected.
Screw clamp
Insulated wire (not supplied)
FM75
AM
Ground wire (not supplied)
Important
If you connect an outdoor antenna, connect a ground wire to the y terminal with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe.
9
Basic Operations
ª
ª
6
Pr
0)
6
ª
Pp
ª
ª
p
6
0)p
)
0
Playing a CD
— Normal Play
You can play up to five CDs in a row.
POWER
1234
1/ALL DISCS
0
P
S
L
A
C
Y
S
I
M
D
O
L
L
D
A
E
/
1
T
I
D
E
A
S
M
Jog dial
DISC SKIP
P
p AMS =/+
0/) CD (
R
E
P
E
R
T
)
1 Press 6 OPEN and place a CD on
the disc tray.
If the disc is not placed properly it will not be recognized.
With the label
·VOLUME
side up. When you play a CD single, place it on the inner circle of the tray.
2 Press DISC SKIP to place up to four
more CDs on the tray.
The disc tray rotates so you can insert other CDs.
3 Close the front cover. 4 Press one of the DIRECT PLAY
buttons.
Playback starts. If you press · (or CD ( on the
pP
remote), playback starts from the CD in the playing position.
Disc number in the playing position
Track number
DOLBY NR
OFF
ALL DISC S
Elapsed time
10
VOLUME +/–
To
Stop playback Pause
Select a track
Find a point in a track
Select a CD
Play only the CD you have selected
Play all CDs
Remove or change the CDs
Adjust the volume
* AMS: Automatic Music Sensor.
Do this
Press p. Press P. Press again to resume
playback. During playback or pause, turn
the jog dial clockwise (to go forward) or counterclockwise (to go backward) and release it when you reach the desired track. Or press AMS* + (to go forward) or AMS* = (to go backward) on the remote.
Press and hold ) or 0 during playback, and release at the desired point.
Press one of the DIRECT PLAY buttons (or DISC SKIP).
Press 1/ALL DISCS repeatedly until “1 DISC” appears.
Press 1/ALL DISCS repeatedly until “ALL DISCS” appears.
Press 6 OPEN.
Turn VOLUME (or press VOLUME +/– on the remote).
Tips
• Pressing · while the system is off automatically turns on the system and starts CD playback if there is a CD on the tray (One Touch Play).
• You can switch from another source to the CD player and start playing a CD just by pressing · or one of the DIRECT PLAY buttons (Automatic Source Selection).
• If there is no CD in the player, “NO DISC” appears in the display.
• You can change the CD in the loading position during playback.
Basic Operations
11
Recording a CD
— CD Synchro Recording
This function lets you record from a CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is adjusted automatically.
POWER
6
SURROUND
DOLBY NR
7
3
1 Press 6 EJECT and insert a blank
tape into deck B.
With the side you want to record on facing forward
ª
ª
6
4
ª
p
p
ª
ª
p0)p
0)
Pr
6
5
12
3 Close the front cover. 4 Press DISC SKIP repeatedly until
the disc number you want to record appears in the playing position indicator.
5 Press CD SYNC.
Deck B stands by for recording and the CD player stands by for playback, and the indicator on the · button (for the front side) lights up green.
6 Press DIRECTION repeatedly to
select A to record on one side or ß (or RELAY) to record on both
sides.
7 Press P on deck B.
Recording starts.
To stop recording
Press p on deck B or on the CD player.
Tips
•If you want to record on the reverse side, press ª so the indicator on the ª button (for the reverse side) lights up green.
•When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side.
•When you want to reduce the hiss noise in low­level high-frequency signals, press DOLBY NR before step 7 so “DOLBY NR B” appears in the display.
•To record with the surround effect, press SURROUND so “SUR display.
The equalizer settings will not be recorded.
Note
You cannot listen to other sources while recording.
” appears in the
2 Press 6 OPEN and place a CD.
With the label side up. When you play a CD single, place it on the inner circle of the tray.
12
ª
ª
0)p
6
ª
ª
p
0)
Pr
6
6
ª
Pp
)
0
Listening to the radio
— Preset Tuning
Before using this function, preset radio stations in the tuner’s memory (see “Step 3: Presetting radio stations”).
STEREO/MONO
POWER
VOLUME
123
3 Press TUNING +/– (or PRESET +/–
on the remote) to tune in the desired preset station.
Preset number
DOLBY NR
OFF
TUNED
STEREO
ALL DISC S
To Do this
Turn off the radio Press POWER. Adjust the volume Turn VOLUME (or press
VOLUME +/– on the remote).
PRESET
MHz
Frequency
PRESET +/– TUNER/BAND
VOLUME +/–
1 Press TUNER/BAND repeatedly
until the band you want appears in the display.
Each time you press this button, the band changes as follows:
FM ˜ AM
2 Press TUNING MODE repeatedly
until “PRESET” appears in the display.
MANUAL n AUTO n PRESET
n
To listen to non-preset radio stations
Press TUNING MODE repeatedly in step 2 until “MANUAL” appears, then press TUNING +/– to tune in the desired station.
Tips
•Pressing TUNER/BAND while the system is off automatically turns on the system and tunes to the last received station (One Touch Play).
•You can switch from another source to the radio just by pressing TUNER/BAND (Automatic Source Selection).
•If an FM program is noisy, press STEREO/ MONO so “MONO” appears in the display. There will be no stereo effect, but the reception will improve. Press this button again to restore the stereo effect.
•To improve broadcast reception, move the supplied antennas.
Basic Operations
13
Recording from the radio
3 Press TUNING +/– to tune in a
preset station.
Preset number
You can record a radio program on a tape by tuning in a preset station. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is automatically adjusted.
POWER
SURROUND
DOLBY NR p
ª
123
4576
1 Press TUNER/BAND repeatedly
until the band you want appears in the display.
2 Press TUNING MODE repeatedly
until “PRESET” appears in the display.
DOLBY NR
OFF
TUNED
STEREO
ALL DISC S
PRESET
Frequency
4 Press 6 EJECT and insert a blank
tape into deck B.
With the side you want to record on facing forward
ª
ª
6
ª
p0)p
Pr
6
0)
ª
5 Press r REC.
Deck B stands by for recording, and the indicator on the · button (for the front side) lights up green.
6 Press DIRECTION repeatedly to
select A to record on one side or ß (or RELAY) to record on both
sides.
7 Press P on deck B.
Recording starts.
To stop recording
Press p on deck B.
MHz
14
Loading...
+ 30 hidden pages