Precautions to be taken when making holes in the wall for the cables
(supplementary instruction for step 4)
Be careful when you make holes near the Plate Unit to feed the cables into the wall, those holes may be visible after you
mount the display.
SU-PW1
To customers using the LCD Color TV
Specifications
B
a
(Angle)
A
This Wall-Mount Bracket can also be used with the Sony KLV30XBR900 LCD Color TV.
When attaching the unit, be sure to follow the supplementary instructions provided on
the back of this page, as well as consulting the instructions given in the Instructions
supplied with the SU-PW1 Wall-Mount Bracket.
KLV30XBR900 Unit: mm (inches)
Angle Dimensions
C
DE
a ABCDE
0°
5°
10°
15°
20°
525 150 67 400 58
(20 21⁄32) (5 29⁄32) (2 5⁄8) (15 3⁄4) (2 9⁄32)
525 187 57 400 67
(20 21⁄32) (7 3⁄8) (2 1⁄4) (15 3⁄4) (2 5⁄8)
525 223 44 400 75
(20 21⁄32) (8 25⁄32) (1 23⁄32) (15 3⁄4) (2 15⁄16)
525 258 28 400 83
(20 21⁄32) (10 5⁄32) (1 3⁄32) (15 3⁄4) (3 9⁄32)
525 291 9 400 90
(20 21⁄32)(11 15⁄32)(
11
⁄32) (15 3⁄4) (3 17⁄32)
The proper procedures must be followed when installing this unit. First, be sure to ask a Sony dealer or a qualified
contractor to perform the work, ensuring that adequate attention is paid to safety and the proper procedures are
followed during the installation.
For Sony Dealers
Sufficient technical expertise is required to install an LCD Color TV, so be sure to consult these supplementary
instructions and the Instructions while installing the product. Sony cannot assume responsibility for improper
assembly or handling that lead to accidents or injury. Give a copy of the Instructions and a copy of these
supplementary instructions to the customer after the installation is completed.
On walls with sufficient strength
If this Wall-Mount Bracket is attached to walls that are not strong enough to support the weight, are not flat, or are not
perpendicular to the floor surface, the unit may fall, and cause injury or damage. The wall must be strong enough to
support at least four times the weight of the display to be attached. (KLV30XBR900: 20 kg (44 lb 1 oz) × 4 = 80 kg (176 lb
6 oz))
© 2003 Printed in U.S.A. x-xxx-xxx-xx (x)
Supplementary instructions for installing an LCD Color TV
During installation, follow the supplementary instructions given below, as well as those in the supplied Instructions, to
ensure proper installation.
Attaching the plate unit to the wall
(supplementary instruction for step 3)
When attaching an LCD Color TV display, the dimensions given in the diagram below are those required for proper
installation. Referring to “Step 3: Install the Plate Unit on the wall” on page 8 (US) of the Instructions and the diagram
below, decide on the location where the unit is to be installed.
2
While one person holds the stand
down firmly, two people should lift
the display straight up to disengage
the hooks (at four places) from the
vertical plate of the stand.
Note
If the stand isn’t held down while the display is being
lifted, the stand will be raised along with the display, and
this can be dangerous.
)
8
⁄
3
35 (1
)
330 (13)
)
8
⁄
3
35 (1
11
110
11
110
11
110
32
⁄
(4
)
32
⁄
(4
)
32
⁄
(4
DC
FE
530 (20 7⁄8)
140 (5 1⁄2)
600 (23 5⁄8)
A
)
4
⁄
3
400 (15
KLV30XBR900 Unit: mm (inches)
ABCDEF
972 525 102 155 175 93
(38
9
⁄32
) (20
21
⁄32
) (4
1
⁄32
) (6
B
3
⁄32
) (6
7
⁄8
) (3
21
⁄32
Attaching the KLV30XBR900 to the Wall-Mount Bracket
(supplementary instruction for step 4)
Perform the procedures outlined below to remove the display from the supplied stand before performing “Step 4: Install
the Display Unit” on page 11 (US) of the Instructions.
)
Remove the two fixing screws from
3
the two lower holes near the upper
portion of the Mounting Hook Unit,
and then re-insert and tighten them in
the two upper holes as shown in the
diagram.
1
Remove the two fixing screws at the
bottom of the plate as shown in the
diagram.
Save the screws for use later.
4
Following the instructions given in
“Step 4: Install the Display Unit” on
page 11 (US) of the Instructions, attach
the display to the Wall-Mount Bracket.