SONY KLV-26HG2 Service Manual

SERVICE MANUAL

SPECIFICATIONS

KLV-26HG2

UC Model

Television system:

American TV standard

Channel coverage:

VHF: 2-13/UHF: 14-69/CATV: 1-125

Antenna:

75 ohm external terminal for VHF/UHF

Screen size (measured diagonally):

26 inches

Panel System:

a-Si TFT Active Matrix LCD panel
(Effective dots: more than 99.99%)

Display resolution:

1280 dots (horizontal) x 768 lines (vertical)

VIDEO 1/2 IN:

S VIDEO IN (4-pin mini DIN):

Y: 1 Vp-p, 75-ohms unbalanced,

sync negative

C: 0.286 Vp-p (Burst signal),

75 ohms

VIDEO: 1 Vp-p, 75-ohms unbalanced,

sync negative

AUDIO: 500 mVrms (100% modulation)

Impedance: 47 kilohms

VIDEO 3 IN:

Y, PB, PR(Component Video ) IN

AUDIO: 500 mVrms (100% modulation)

VIDEO 4 IN:

DVI-HDTV:

AUDIO: 500 mVrms (100% modulation)

:

Y: 1.0 Vp-p, 75 ohms

unbalanced, sync negative

B

: 0.7 Vp-p, 75 ohms

P
P

R

: 0.7 Vp-p, 75 ohms

Signal format:

480i, 480p, 720p, 1080i

Impedance: 47 kilohms

1 terminal, 3.3V T.M.D.S,
50 ohms
The DVI-HDTV input terminals
compliant with the EIA-861B
standard and is not intended for
use with PC.

Impedance: 47 kilohms

:

LCD Colour TV

AUDIO OUT:

500 mVrms (100% modulation)
More than 500 mVrms at the maximum volume setting
(Variable)
More than 500 mVrms (Fixed)

Headphones:

Stereo minijack
Impedance: 16 ohms

Speaker:

Full range: 4.0 x 10.0 cm 0val

(1

1

/

4

inches) (2)

Tweeter: ø2.5 cm

Speaker output:

(31/32 inches) (2)

4.0 W x 4.0 W

Power requirement:

120 V AC, 60 Hz

Power consumption:

In use: 118 W
In standby: Less than 1W

Dimensions (W/H/D):

Including TV stand and rear cover:

790 x 490 x 240 mm

3

/32 x 19 9/32 x 97/16 inches)

(31

Without TV stand and rear cover:

790 x 430 x 138 mm

3

/32 x 16 15/16 x 5 7/16 inches)

(31

Mass:

Including TV stand and rear cover:

790 x 490 x 240 mm kg

Without TV stand and rear cover:

12.2 kg (26 lb 14 oz)

Supplied accessories:

Remote control RM-1105 (1)
size AA Batteries (2)
75-ohm coaxial cable (1)
AC power cord (1)
Rear cover (1)
Operating Instructions
Warranty Card

Product Registratuin

Optional accessorios:

Note that some optional accessories may be out of
stock.

Headphones plug adaptor
Connecting cables

"Memory Stick" media

Wall-Mount Bracket

SU-LW1

Design and specifications are subject to change
without notice.

KLV-26HG2 (UC) 2

SAFETY CHECK-OUT

After correcting the original service problem, perform the fol­lowing safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly-sol­dered connections. Check the entire board surface for solder
splashes and bridges.

2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly tran­sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.

6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.

7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.

8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described right.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part
having a return to chassis, must not exceed 0.5 mA (500
microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instruments.

2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica­tion is 0.75 V, so analog meters must have an accurate low­voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable. (See Fig. A)

WARNING!!

SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON THE SCHEMATIC DIAGRAMS, EXPLODED
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR
SAFE OPERATION. REPLACE THESE COMPONENTS
WITH SONY PARTS WHOSE PART NUMBERS AP­PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE­MENTS PUBLISHED BY SONY. CIRCUIT ADJUST­MENTS THAT ARE CRITICAL FOR SAFE OPERATION
ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE
PROCEDURES WHENEVER CRITICAL COMPONENTS
ARE REPLACED OR IMPROPER OPERATION IS SUS­PECTED.

AVERTISSEMENT!!
ATTENTION AUX COMPOSANTS RELATIFS À LA
SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET
UNE MARQUE ! SONT CRITIQUES POUR LA
SÉCURITÉ. NE LES REMPLACER QUE PAR UNE
PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES
RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST
CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIÉS DANS LE
PRÉSENT MANUEL. SUIVRE CES PROCÉDURES
LORS DE CHAQUE REMPLACEMENT DE
COMPOSANTS CRITIQUES, OU LORSQU’UN
MAUVAIS FONCTIONNEMENT EST SUSPECTÉ.

To Exposed Metal
Parts on Set

0.15 µF

1.5 k

Ω

Earth Ground

AC
Voltmeter
(0.75 V)

Fig. A. Using an AC voltmeter to check AC leakage.

KLV-26HG2 (UC) 3

TABLE OF CONTENTS

1. DISASSEMBLY ......................................1-1

1-1.

REAR COVER AND STAND ASSY REMOVAL .....

1-2. CABINET ASSY REMOVAL ............................... 1-1

1-3. U1 BOARD REMOVAL ....................................... 1-2

1-4. MS AND MSB BOARDS REMOVAL .................. 1-2

1-5. G1 BOARD REMOVAL....................................... 1-3

1-6. A1, TU AND UD BOARDS REMOVAL............... 1-3

1-7. HB BOARD REMOVAL ...................................... 1-4

1-8. H1 AND MSX BOARDS REMOVAL................... 1-4

1-9. H2 BOARD REMOVAL ....................................... 1-5

1-10. H3 BOARD REMOVAL ..................................... 1-5

2. EXPLODED VIEWS ...............................2-1

2-1. CABINET ASSY AND STAND ASSY ................. 2-2

2-2. CHASSIS ............................................................ 2-3

2-3. PACKING MATERIALS ...................................... 2-4

2. ELECTRICAL PARTS LIST...................2-1

1-1

KLV-26HG2 (UC) 4

SECTION 1

DISASSEMBLY

1-1. REAR COVER AND STAND ASSY REMOVAL

1 Rear cover

2 Four screws

(+PSW 4x16)

3 Stand assy

1-2. CABINET ASSY REMOVAL

1 Four screws

(+PSW 4x8)

3 Cabinet assy

2 Two screws

(+BVTP 3x10)

KLV-26HG2 (UC) 1-1

1-3. U1 BOARD REMOVAL

3ねじ2本
(+BVTT3x6)

4U3基板

1 Two screws

(+BVTT 3x6)

2 U1 board

1-4. MS AND MSB BOARDS REMOVAL

1 Four screws

(+PSW 4x10)

2 VESA frame & bracket

3 Two screws

(+BVTT 3x6)

4 MSB board

5 Four screws

(+BVTT 3x6)

6 MS shield

7 MSB board

KLV-26HG2 (UC) 1-2

1-5. G1 BOARD REMOVAL

1 Five screws

(+BVTT 3x6)

2 G1 board

1-6. A1, TU AND UD BOARDS REMOVAL

7 UD shield case

6 Two connector screws

3 Two screws

(+BVTP 3x8)

8 UD board

1 Two screws

(+BVTT 3x6)

2 TU board
4 Four screws

(+BVTT 3x6)

5 A1 board

KLV-26HG2 (UC) 1-3

1-7. HB BOARD REMOVAL

1 Two screws

(+BVTT 3x6)

2 DVI bracket

3 Four screws

(+BVTT 3x6)

4 B board

1-8. H1 AND MSX BOARDS REMOVAL

2 Two screws

(+BVTP 3x8)

3 H1 board

1 Two screws

(+BVTP 3x8)

4 Two screws

(+BVTT 3x6)

6 MSX board

5 Screw

(+BVTP 3x10)

KLV-26HG2 (UC) 1-4

1-9. H2 BOARD REMOVAL

1 Four screws

(+BVTP 3x8)

3 H2 board

2 Two screws

(+BVTP 3x8)

1-10. H3 BOARD REMOVAL

2 H3 board

1 Two screws

(+BVWHTP 3x12)

KLV-26HG2 (UC) 1-5E

SECTION 2

EXPLODED VIEWS

NOTE:

The components identified ! marked are
critical for safety.
Replace only with the part number specified.

Les composants identifiés par la marque !

sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant

le numéro spécifié.

• Items with no part number and no description are
not stocked because they are seldom required for
roution service.

• The construction parts of an assembled part are
indicated with a collation number in the remark
colum.

• Items marked " * " are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.

KLV-26HG2 (UC) 2-1

2-1. CABINET ASSY AND STAND ASSY

#1

#1

2

#1

1

#1

3

11

4

9

7

8

#3

#3

#3

16

#4

#6

#5

#5

14

#2

10

#1

6

REF. No. PART No. DESCRIPTIONRE MARK

1 1-825-677-11 LOUDSPEAKER
2 1-825-677-21 LOUDSPEAKER
3 * A-1410-783-A H1 BO ARD, MOUNT
4 X-4042-863-3 BUTTON BRACKET ASSY
5 * A-1410-784-A H2 BO ARD, MOUNT

6 4-100-305-11 TERMINAL, SIDE
7 X-4042-865-1 CABINET ASSY 8
8 4-095-322-01 BUSHING, RUBBER
9 4-100-323-03 BASE, STAND
10 4-100-324-01 COVER, ARM

5

12

#1

13

13

13

15

15

REF. No. PART No. DESCRIPTIONRE MARK

11 X-4042-966-1 MLUTI BUTTON ASSY
12 * X-4042-840-2 STAND ASSY 13
13 4-101-439-01 FOOT, STAND
14 4-094-922-22 COVER, ECS (15V)
15 4-101-526-01 SCREW , BAIND HEAD +TP4X8 TYPE2

16 4-101-249-01 COVER, REAR
#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

#2 7-685-872-09 SCREW +BVTT 3X8 (S)
#3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 SLIT
#4 7-682-961-09 SCREW +PSW 4X8
#5 7-685-661-79 SCREW +P 4X12 TYPE2 NON-SLIT
#6 7-682-965-01 SCREW +PSW 4X16

KLV-26HG2 (UC) 2-2

2-2. CHASSIS

53

#12

#12

#3

#3

60

#1

52

72

57

59

#8

58

#12

74

#8

55

72

#9

#8

56

76

#8

#10

71

67

#11

73

#8

75

65

#8

61

64

#8

#8

#7

#7

62

63

#8

#8

#3

66

#8

70

#12

#8

68

69

51

54

REF. No. PART No. DESCRIPTIONRE MARK REF. No. PART No. DESCRIPTIONRE MARK

51 * A-1410-787-A H3 BOARD, MOUNT
52 1-805-494-12 LCD MODULE
53 1-900-283-43 LVDS CONNECTOR
54 * 4-100-304-02 BRACKET, LED
55 ! 1-818-024-11 AC INLET

56 * A-1410-789-A G1 BOARD , MOUNT
57 * A-1405-862-A UD BOARD, MOUNT
58 * A-1410-790-A A1 BOARD, MOUNT
59 * A-1410-785-A TU BOARD , MOUNT
60 4-635-966-01 SCREW (HEX)

61 * A-1410-385-A MSB BOARD , MOUNT
62 * A-1410-786-A U1 BOARD, MOUNT
63 3-682-691-00 NUT , W ASHER HEXAGON
64 1-827-467-41 CORD , CONNECTION
65 * A-1410-489-B MS BOARD, MOUNT

71 * 3-615-538-01 SPACER,CIRCUIT BOARD
72 4-102-673-01 BUSHING, INSULATE SPECI
73 * 4-662-796-01 CLIP, COACHING
74 * 4-095-199-01 SHEET (A), RADIA TION
75 * 4-101-182-01 CUSHION (TOP)

76 * 4-092-814-02 CUSHION D
#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

#3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 SLIT
#7 7-682-962-01 SCREW +PSW 4X10
#8 7-685-871-01 SCREW +BVTT 3X6 (S)
#9 7-685-661-79 SCREW +BVTP 4X12 TYPE2 IT-3
#10 7-685-881-09 SCREW +BVTT 4X8 (S)
#11 7-682-961-01 SCREW +PSW 4X8
#12 7-685-862-09 SCREW +BVTT 2.6X6 (S)

66 * A-1410-384-A MSX BOARD , MOUNT
67 1-500-418-11 CORE
68 * A-1410-792-A B BOARD, MOUNT
69 4-029-432-21 SCREW 3, (+) BVWHTP
70 X-4042-864-2 BEZEL ASSY

KLV-26HG2 (UC) 2-3

2-3. PACKING MATERIALS

108

106

104

110

105

103

102

113

107

114

119

116
117

120

112

118

115

106

109

104

111

101

REF. No. PART No. DESCRIPTIONRE MARK REF. No. PART No. DESCRIPTIONRE MARK

101 * 4-101-559-02 CARTON
102 * 4-101-235-01 STAND SUPPOR T
103 * 4-101-236-01 BOTTOM PAD
104 * 4-101-180-01 CUSHION LOWER
105 * 4-102-248-01 SEET, PROTECTION CROSS

111 * 4-101-243-01 CUSHION, SUPPORT (LOWER-R)
112 * 4-101-441-01 ACCESSORY TRA Y
113 1-827-804-11 CORD , POWER”
114 1-478-382-11 REMOTE COMMANDER (RM-Y1105)
115 * 4-101-694-01 PAT, REAR COVER

106 * 4-101-179-02 CUSHION UPPER
107 * 4-101-237-01 BAG, PROTECTION CROSS
108 * 4-101-240-01 CUSHION, SUPPORT (UPPER-L)
109 * 4-101-241-01 CUSHION, SUPPORT (UPPER-R)
110 * 4-101-242-01 CUSHION, SUPPORT (LOWER-L)

116 1-757-319-52 CABLE, COAXIAL (WITH (F) PLUG)
117 4-101-560-12 “MANUAL, INSTRUCTION

4-101-560-22 MANUAL, INSTR UCTION

4-101-560-32 MANUAL, INSTR UCTION
118 * 4-101-899-01 PAT, REAR COVER (B)
119 * 4-103-022-11 BAG, PROTECTION (RC)
120 4-101-249-01 REAR COVER

KLV-26HG2 (UC) 2-4E

SECTION 3

ELECTRICAL PARTS LIST

NOTE:

The components identified ! marked are
critical for safety.
Replace only with the part number specified.

Les composants identifiés par la marque !
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

When indicating parts by reference number,
please include the board name.

• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.

• Items marked " * " are not stocked since they are
seldom required for routine service. Some delay should
be anticipated when ordering these items.

RESISTORS

• All resistors are in ohms

• F : nonflammable

KLV-26HG2 (UC) 3-1

No. # Board Type !/* Ref. No. Part No. Description Remarks-1 Remarks-2

1 UD CAPACITOR C3800 1-162-917-11 CERAMIC CHIP 15PF 5.00% 50V
2 UD CAPACITOR C3801 1-162-917-11 CERAMIC CHIP 15PF 5.00% 50V
3 UD CAPACITOR C3802 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
4 UD CAPACITOR C3803 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
5 UD CAPACITOR C3804 1-164-156-11 CERAMIC CHIP 0.1UF 25V
6 UD CAPACITOR C3805 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
7 UD CAPACITOR C3806 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
8 UD CAPACITOR C3807 1-164-156-11 CERAMIC CHIP 0.1UF 25V

9 UD CAPACITOR C3808 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
10 UD CAPACITOR C3809 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
11 UD CAPACITOR C3810 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
12 UD CAPACITOR C3811 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
13 UD CAPACITOR C3812 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
14 UD CAPACITOR C3813 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
15 UD CAPACITOR C3814 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
16 UD CAPACITOR C3815 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
17 UD CAPACITOR C3816 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
18 UD CAPACITOR C3817 1-164-156-11 CERAMIC CHIP 0.1UF 25V
19 UD CAPACITOR C3818 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
20 UD CAPACITOR C3819 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
21 UD CAPACITOR C3820 1-126-395-11 ELECT CHIP 22UF 20.00% 16V
22 UD CAPACITOR C3821 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
23 UD CAPACITOR C3822 1-164-156-11 CERAMIC CHIP 0.1UF 25V
24 UD CAPACITOR C3823 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
25 UD CAPACITOR C3824 1-164-156-11 CERAMIC CHIP 0.1UF 25V
26 UD CAPACITOR C3825 1-164-156-11 CERAMIC CHIP 0.1UF 25V
27 UD CAPACITOR C3826 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
28 UD CAPACITOR C3827 1-164-156-11 CERAMIC CHIP 0.1UF 25V
29 UD CAPACITOR C3828 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
30 UD CAPACITOR C3829 1-164-156-11 CERAMIC CHIP 0.1UF 25V
31 UD CAPACITOR C3832 1-126-395-11 ELECT CHIP 22UF 20.00% 16V
32 UD CAPACITOR C3833 1-126-395-11 ELECT CHIP 22UF 20.00% 16V
33 UD CAPACITOR C3834 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
34 UD CAPACITOR C3837 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
35 UD CAPACITOR C3838 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
36 UD CAPACITOR C3840 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
37 UD CAPACITOR C3841 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
38 UD CAPACITOR C3842 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
39 UD CAPACITOR C3843 1-164-156-11 CERAMIC CHIP 0.1UF 25V
40 UD CAPACITOR C3844 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
41 UD CAPACITOR C3845 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
42 UD CAPACITOR C3846 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
43 UD CAPACITOR C3847 1-164-156-11 CERAMIC CHIP 0.1UF 25V
44 UD CAPACITOR C3848 1-164-156-11 CERAMIC CHIP 0.1UF 25V
45 UD CAPACITOR C3849 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
46 UD CAPACITOR C3850 1-162-927-11 CERAMIC CHIP 100PF 5.00% 50V
47 UD CAPACITOR C3851 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
48 UD CAPACITOR C3852 1-115-416-11 CERAMIC CHIP 0.001UF 5.00% 25V
49 UD CAPACITOR C3854 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
50 UD CAPACITOR C3860 1-162-927-11 CERAMIC CHIP 100PF 5.00% 50V
51 UD CAPACITOR C3861 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
52 UD CAPACITOR C3862 1-164-156-11 CERAMIC CHIP 0.1UF 25V
53 UD CAPACITOR C3863 1-164-156-11 CERAMIC CHIP 0.1UF 25V
54 UD CAPACITOR C3864 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
55 UD CAPACITOR C3865 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
56 UD CAPACITOR C3866 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
57 UD CAPACITOR C3867 1-164-156-11 CERAMIC CHIP 0.1UF 25V
58 UD CAPACITOR C3868 1-126-395-11 ELECT CHIP 22UF 20.00% 16V
59 UD CAPACITOR C3869 1-164-156-11 CERAMIC CHIP 0.1UF 25V
60 UD CAPACITOR C3872 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
61 UD CAPACITOR C3873 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
62 UD CAPACITOR C3874 1-162-923-11 CERAMIC CHIP 47PF 5.00% 50V
63 UD CAPACITOR C3875 1-162-923-11 CERAMIC CHIP 47PF 5.00% 50V
64 UD CAPACITOR C3876 1-162-923-11 CERAMIC CHIP 47PF 5.00% 50V
65 UD CAPACITOR C3878 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
66 UD CAPACITOR C3879 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V
67 UD CAPACITOR C3880 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
68 UD CAPACITOR C3881 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
69 UD CAPACITOR C3883 1-162-921-11 CERAMIC CHIP 33PF 5.00% 50V
70 UD CAPACITOR C3884 1-162-921-11 CERAMIC CHIP 33PF 5.00% 50V
71 UD CAPACITOR C3885 1-164-156-11 CERAMIC CHIP 0.1UF 25V
72 UD CAPACITOR C3886 1-124-779-00 ELECT CHIP 10UF 20.00% 16V
73 UD CAPACITOR C3887 1-164-156-11 CERAMIC CHIP 0.1UF 25V

KLV-26HG2 (UC) 3-2