Sony KDL-52XBR, KDL-46XBR, KDL-40XBR, KDL-52X3100, KDL-46X3100 Installation Manual

Installing the Wall-Mount Bracket

To Customers:

For product protection and safety reasons, Sony strongly recommends that installing of
your TV be performed by Sony dealers or licensed contractors. Do not attempt to install
it yourself.

Your KDL-52XBR/KDL-46XBR/KDL-40XBR/KDL-52X3100/KDL-46X3100/KDL­40X3100 can be installed using SU-WL500 Wall-Mount Bracket (sold separately). Please
provide your licensed contractor with this installation supplement as well as the
Instructions (supplied with the SU-WL500 Wall-Mount Bracket). Read these documents
carefully for safety and proper installation.

3-272-867-12(1)

KDL-52XBR
KDL-46XBR
KDL-40XBR

To Sony Dealers and Contractors:

Provide full attention to safety during the installation, periodic maintenance and
examination of this product.

KDL-52X3100
KDL-46X3100
KDL-40X3100

Printed in Japan

© 2007 Sony Corporation

3272867120

Installing the TV

The TV can be installed on a wall by attaching a Wall­Mount Bracket (sold separately).
Verify your TV’s model number and be sure to use the
bracket specified for your model only. Refer to the
Steps on this manual along with the Instructions
supplied with the SU-WL500 Wall-Mount Bracket, to
properly carry out the installation.

Sufficient expertise is required for installing this
product, especially to determine the strength of the
wall for withstanding the TV’s weight. Be sure to
entrust the attachment of this product to the wall to
Sony dealers or licensed contractors and pay
adequate attention to safety during the installation.
Sony is not liable for any damage or injury caused
by mishandling or improper installation.

Step 1: Checking the parts

required for the
installation

Open the Wall-Mount Bracket package and check the
contents for all required parts along with the
Instructions.

Step 2: Deciding on the

installation location

Decide where you want to install your TV. Refer to
“TV installation dimensions table” in this manual for
the TV installation dimensions table.

Refer to the Instructions for SU-WL500.

Step 3: Installing the Base

Bracket on the wall

Refer to the Instructions for SU-WL500.

Step 4: Preparing for the

installation of the TV

Before detaching the Table-Top Stand, disconnect all
the cables from the TV. Refer to Operating Instructions
supplied with the TV set for detaching the Table-Top
Stand.
Referring to “Screw and Hook locations diagram/
table” in this manual, determine the screw positions,
and secure the Mounting Hook to the rear of the TV.

When changing the bezel unit to the optional one,
replace it before removing the Table-Top Stand. The
bezel unit cannot be replaced after installing on a wall.
(KDL-52X3100/KDL-46X3100/KDL-40X3100 only)

TV installation dimensions table

320

Screen centre point

Unit: mm

Model Name

KDL-52XBR 1,415 827 73 491 185 415 781 533

KDL-52X3100 1,415 827 73 491 183 415 781 533

KDL-46XBR 1,262 734 128 500 183 378 694 542

KDL-46X3100 1,262 734 128 500 181 378 694 542

KDL-40XBR 1,111 657 176 509 183 349 621 550

KDL-40X3100 1,111 657 176 509 181 349 621 550

Figures in the above table may differ slightly depending on the installation.

WARNING

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to the
Operating Instructions supplied with the TV set for its weight.

Display dimensions Screen centre dimension

AB C DEFGH

Length for each mounting angle

Angle (0°) Angle (20°)

Screw and Hook locations diagram/table

Model Name Screw location Hook location

KDL-52XBR/KDL-52X3100 d, g a

KDL-46XBR/KDL-46X3100/KDL-40XBR/KDL-40X3100 e, g b

* Hook position “c” cannot be used for the models in the table above.

Screw location

Hook location

a
b
c*

Step 5: Installing the TV on

the wall

Refer to the Instructions for SU-WL500.