Sony KDL-32W4220 User Manual [ru]

0 (0)

LCD Digital Colour TV

For useful information about Sony products

Для получения полезной информации о продукции Сони

Szczegółowe informacje o produktach Sony Užitečné informace o výrobcích Sony Pre viac informácií o produktoch Sony Sony termékekről hasznos információkat találhat az alábbi weboldalon

Printed in Spain

3-298-243-43(1)

Operating Instructions

KDL-52W40xx

KDL-52W42xx

KDL-46W40xx

KDL-46W42xx

KDL-40W40xx

KDL-40W42xx

KDL-32W40xx

KDL-32W42xx

KDL-40E40xx

KDL-32E40xx

KDL-26E40xx

KDL-37V45xx

KDL-37V47xx

KDL-32V45xx

KDL-32V47xx

KDL-26V45xx

KDL-26V47xx

Инструкция по эксплуатации

Instrukcja obsługi

Návod k použití

Návod na obsluhu

Kezelési utasítás

Introduction

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.

Disposal of the TV set

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the

packaging indicates that the battery

provided with this product shall not be

treated as household waste. By ensuring

these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 1080075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Notice for Digital TV function

• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2 and MPEG4 AVC) digital terrestrial signals are broadcast or where you have access to a compatible DVB-C (MPEG2 and MPEG4 AVC) cable service. Please confirm with your local dealer if you can receive a DVB-T signal where you live or ask your cable provider if their DVBC cable service is suitable for integrated operation with this TV.

• The cable provider may charge an additional fee for such a service and you may be required to agree to their terms and conditions of business.

• Although this TV set follows DVB-T and DVB-C specifications, compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some countries/regions and DVB-C cable may not operate correctly with all providers.

• For more information about DVB-C functionality please see our cable support site: http://support.sony-europe.com/TV/DVBC

Trademark information

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

ViV

HD3D Sound

• The illustrations used in this manual are of the KDL-40W4000 unless otherwise state.

• The "x" that appear on the model name, correspond to numeric digits related to colour variation.

Table of Contents

Start-up Guide 4

Start-up Guide 4Checking the accessories.................................................................................................... 4

Safety information................................................................................................................9

Precautions........................................................................................................................10

Overview of the remote ................................................................................................... 11

Overview of the TV buttons and indicators...................................................................12

Watching TV

Watching TV....................................................................................................................... 13

Checking the Guide .................................................................................................. 15

Using the Digital Favourite list .................................................................................. 16

Using Optional Equipment

Connecting optional equipment.......................................................................................... 17

Viewing pictures from connected equipment ..................................................................... 18

Using BRAVIA Sync (Control for HDMI) ............................................................................ 19

Using MENU Functions

Overview of the TV Home Menu (XMB™)......................................................................... 21

Settings..............................................................................................................................22

Instruction Manual ........................................................................................................ 22

Picture ..........................................................................................................................22

Sound ...........................................................................................................................23

Features .......................................................................................................................24

Set-up ...........................................................................................................................26

Analogue Set-up .......................................................................................................... 28

Digital Set-up .......................................................................................................30

Photo .................................................................................................................................32

Picture Frame ............................................................................................................... 32

USB Photo Viewer ....................................................................................................... 32

Additional Information

Specifications..................................................................................................................... 33

Troubleshooting .................................................................................................................36

: for digital channels only

Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.

Start-up Guide

1: Checking the accessories

Mains lead (1) (only for KDL-52W4xxx, KDL46W4xxx, KDL-40W4xxx, KDL-40E4xxx)

Remote RM-ED011 (1) Remote RM-ED011 W (1) (only for KDL-

40E4xxx, KDL-32E4xxx, KDL-26E4xxx) Size AA batteries (R6 type) (2) Stand (1) (except for KDL-52W4xxx,

KDL-26E4xxx) Screws for stand (4) (only for KDL-

46W4xxx, KDL-40W4xxx, KDL-40E4xxx, KDL-37V4xxx)

Screws for stand (3) (only for KDL32W4xxx, KDL-32E4xxx, KDL-32V4xxx, KDL-26V4xxx)

To insert batteries into the remote

Push and lift the cover to open.

2: Attaching the stand

(except for KDL-52W4xxx, KDL-26E4xxx)

1 Open the carton box and take out the stand

and the screws.

2 Place the TV set on the stand. Take care not to

interfere with cables.

3: Connecting an aerial/VCR/ DVD recorder

Start-up Guide

onnecting an aerial/cable

Terrestrial signal

or cable

Coaxial cable

3 Fix the stand to the TV using the supplied

screws.

KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx KDL-37V4xxx

KDL-32W4xxx KDL-32E4xxx KDL-32V4xxx KDL-26V4xxx

Connecting an aerial/ cable/ VCR/ DVD recorder

If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm)

Scart lead

Coaxial cable

Terrestrial signal

or cable

Coaxial cable

VCR/ DVD recorder

4: Preventing the TV

Performing the initial

from toppling over

1 Install a wood screw (4 mm in diameter, not

supplied) in the TV stand.

2 Install a machine screw (M6 x 12, not

supplied) into the screw hole of the TV.

3 Tie the wood screw and the machine screw

with a strong cord.

5: Connecting the cables

set-up

GUIDE

3,4,5

KDL-52W4xxx KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx

6: Bundling the cables

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the TV.

When you switch on the TV for the first time, the Language menu appears on the screen.

3 Press F/f/G/g to select the language

displayed on the menu screens, then press .

Language

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Català

Português

Polski

Set

Česky

Magyar

Русский

лгар

Suomi

Dansk

Svenska

Norsk

Slovenčina

Română

ски

Analogue

Back

Press F/f to select the country/region in which you will operate the TV, then press .

Country

Select country

Set

United Kingdom

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

Analogue

Back

If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region.

5 Press F/f to select the location type in which

you will operate the TV, then press .

Sony recommends you to select “Home” for power saving.

Location

Select location

Home

Shop

Analogue

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding.

If a message appears for you to confirm the aerial connection

No digital or analogue channels were found. Check all the aerial/cable connection and then press to start auto-tuning again.

3 When the Programme Sorting menu appears

on the screen, follow the steps of “Programme Sorting”(page 28).

If you do not change the order in which the analogue channels are stored on the TV, press

RETURN to go to step 4.

Quick Start

Do you want to enable Quick Start?

TV turns on mo re quickly but st andby power

consumption is increased.

Yes No

Analogue

Start-up Guide

Set

This option selects the initial picture mode appropriate for the typical lighting condition in these enviroments.

8: Auto-tuning the TV

1 Select OK then press .

Auto Tuning

Do you want to start Auto Tuning?

OK Cancel

Set

2 Press F/f to select “Antenna” or “Cable”,

then press .

If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for Cable connection” (page 8).

Analogue

Set

Back

For details, see page 24.

Back

Control for HDMI

Set

Do you want to enable control for compatible

HDMI devices?

Yes No

Analogue

Back

For details, see page 19.

6 Press .

The TV has now tuned in all the available channels.

When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts, the time must be set after performing step 3.

Back

To tune the TV for Cable connection

1 Press . 2 Press F/f to select “Quick Scan” or “Full

Scan”, then press .

"Quick Scan" : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for "Frequency", "Network ID" and "Symbol Rate" is "Auto". This option is recommended for fast tuning when supported by your cable operator. If the "Quick Scan" does not tune, please use the "Full Scan" method below. "Full Scan" : All available channels are tuned and stored. This procedure may take some time. This option is recommended when "Quick Scan" is not supported by your cable provider. For further information about supported cable providers, refer to support web site: http://support.sony-europe.com/TV/DVBC/

3 Press f to select “Start”, then press .

The TV starts searching for channels. Do not press any buttons on the TV or remote.

Some cable providers do not support “Quick Scan”. If no channels are detected using “Quick Scan”, perform “Full Scan”.

Detaching the TableTop Stand from the TV

Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.

KDL-52W4xxx KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx KDL-37V4xxx

KDL-26E4xxx

KDL-32W4xxx KDL-32E4xxx KDL-32V4xxx KDL-26V4xxx

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.

Installation

s The TV set should be installed near an easily accessible mains

socket.

s Place the TV set on a stable, level surface. s Only qualified service personnel should carry out wall

installations.

s For safety reasons, it is strongly recommended that you use

Sony accessories, including:

- KDL-52W40xx/ KDL-52W42xx/ KDL-46W40xx/

KDL-46W42xx/ KDL-40W40xx/ KDL-40W42xx/ KDL-32W40xx/ KDL-32W42xx/ KDL-40E40xx/ KDL-32E40xx/ KDL-37V45xx/ KDL-37V47xx/

KDL-32V45xx/ KDL-32V47xx:

Wall-Mount Bracket SU-WL500.

- KDL-26V45xx/ KDL-26V47xx/ KDL-26E40xx:

Wall-mount Bracket SU-WL100.

- KDL-46W40xx/ KDL-46W42xx/ KDL-40W40xx/

KDL-40W42xx/KDL-32W40xx/ KDL-32W42xx/ KDL-40E40xx/ KDL-32E40xx/ KDL-37V45xx/ KDL-37V47xx/ KDL-32V45xx/ KDL-32V47xx:

TV stand SU-FL300M.

s Be sure to use the screws supplied with the Wall-mount bracket

when attaching the mounting hooks to the TV set. The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook. The diameter and length of the screws differ depending on the Wall-mount bracket model. Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

8 mm - 12 mm

Ventilation

s Never cover the ventilation holes or insert anything in the

cabinet.

s Leave space around the TV set as shown below. s It is strongly recommended that you use a Sony wall-mount

bracket in order to provide adequate air-circulation.

Installed on the wall

30 cm

10 cm

Leave at least this space around the set.

10 cm

Installed with stand

30 cm

10 cm 10 cm

Leave at least this space around the set.

s To ensure proper ventilation and prevent the collection of dirt

or dust: – Do not lay the TV set flat, install upside down, backwards,

or sideways. – Do not place the TV set on a shelf, rug, bed or in a closet. – Do not cover the TV set with a cloth, such as curtains, or

items such as newspapers, etc. – Do not install the TV set as shown below.

Air circulation is blocked.

6 cm

Screw (supplied with the Wall-mount bracket)

Mounting Hook Hook attachment on rear of TV set

Transporting

s Before transporting the TV set,

disconnect all cables.

s Two or three people are needed

to transport a large TV set.

s When transporting the TV set

by hand, hold it as shown on the right. Do not put stress on the LCD panel.

s When lifting or moving the TV

set, hold it firmly from the bottom.

s When transporting the TV set,

do not subject it to jolts or excessive vibration.

s When transporting the TV set

for repair or when moving, pack it using the original carton and packing material.

Be sure to hold the bottom of the panel, not the front part. Do not handle with dent area. Do not handle with the transparent bottom part.

Wall Wall

Mains lead

Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:

– Use only mains leads supplied by Sony, not other suppliers. – Insert the plug fully into the mains socket. – Operate the TV set on a 220–240 V AC supply only. – When wiring cables, be sure to unplug the mains lead for your

safety and take care not to catch your feet on the cables.

– Disconnect the mains lead from the mains socket before

working on or moving the TV set.

– Keep the mains lead away from heat sources. – Unplug the mains plug and clean it regularly. If the plug is

covered with dust and it picks up moisture, its insulation may deteriorate, which could result in a fire.

Continued

Notes

s Do not use the supplied mains lead on any other equipment. s Do not pinch, bend, or twist the mains lead excessively. The

core conductors may be exposed or broken.

s Do not modify the mains lead. s Do not put anything heavy on the mains lead. s Do not pull on the mains lead itself when disconnecting the

mains lead.

s Do not connect too many appliances to the same mains socket. s Do not use a poor fitting mains socket.

Prohibited Usage

Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.

Broken pieces:

s Do not throw anything at the TV set. The screen glass may

break by the impact and cause serious injury.

s If the surface of the TV set cracks, do not touch it until you have

unplugged the mains lead. Otherwise electric shock may result.

When not in use

s If you will not be using the TV set for several days, the TV set

should be disconnected from the mains for environmental and safety reasons.

s As the TV set is not disconnected from the mains when the TV

set is just turned off, pull the plug from the mains to disconnect the TV set completely.

s However, some TV sets may have features that require the TV

set to be left in standby to work correctly.

For children

s Do not allow children to climb on the TV set. s Keep small accessories out of the reach of children, so that they

are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the mains lead immediately if any

of the following problems occur. Ask your dealer or Sony service centre to have it checked by

qualified service personnel.

When:

– Mains lead is damaged. – Poor fitting of mains socket. – TV set is damaged by being dropped, hit or having something

thrown at it.

– Any liquid or solid object falls through openings in the cabinet.

Precautions

Viewing the TV

s View the TV in moderate light, as viewing the TV in poor light

or during long period of time, strains your eyes.

s When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

LCD Screen

s Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

s Do not push or scratch the front filter, or place objects on top of

this TV set. The image may be uneven or the LCD screen may be damaged.

s If this TV set is used in a cold place, a smear may occur in the

picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

s Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

s The screen and cabinet get warm when this TV set is in use.

This is not a malfunction.

s The LCD screen contains a small amount of liquid crystal.

Some fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/ cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning.

To avoid material degradation or screen coating degradation, observe the following precautions.

s To remove dust from the screen surface/cabinet, wipe gently

with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

s Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

s When adjusting the angle of the TV set, move it slowly so as to

prevent the TV set from moving or slipping off from its table stand.

Optional Equipment

Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.

Batteries

s Observe the correct polarity when inserting batteries. s Do not use different types of batteries together or mix old and

new batteries.

s Dispose of batteries in an environmentally friendly way.

Certain regions may regulate the disposal of batteries. Please consult your local authority.

s Handle the remote with care. Do not drop or step on it, or spill

liquid of any kind onto it.

s Do not place the remote in a location near a heat source, a place

subject to direct sunlight, or a damp room.

Overview of the remote

1 "/1 – TV standby

Turns the TV on and off from standby mode.

2 AUDIO

In analogue mode: Press to change the dual sound mode (page 24). In digital mode: Press to select the audio language (page 30).

3 – Subtitles

GUIDE

Press to display the subtitles on current program if TV channels broadcast such information (in digital mode only) (page 30).

4 / – Input select / Text hold

• In TV mode: Selects the input source from equipment connected to the TV sockets (page 18).

• In Text mode (page 14): Holds the current page.

5 F/f/G/g/ 6 OPTIONS (page 14, 19)

Enables you to access various viewing options and change/make adjustments according to the source and screen format.

7 HOME (page 21)

Displays the TV Home menu.

8 Coloured buttons (page 14, 15, 16) 9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the second and third digit quickly.

• In Text mode: Enters the three digit page number to select the page.

0 – Favourite (page 16) qa PROG +/–//

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode (page 14): Selects the next ( ) or previous ( ) page.

qs – Previous channel

Returns to the previous channel watched (for more than five seconds).

qd % – Mute the sound qf 2 +/– – Volume qg / – Text (page 14) qh – RETURN

Returns to the previous screen of any displayed menu.

qj – GUIDE (page 15) qk ANALOG – Analogue mode (page 13) ql DIGITAL – Digital mode (page 13) w; BRAVIA Sync (page 19) wa – Screen mode (page 14) ws / – Info / Text reveal

• In digital mode: Displays details of the programme currently being watched.

• In analogue mode: Each time you press screen changes as follows: Displays information such as current channel number and screen format

• In Text mode (page 14): Reveals hidden information (e.g. answers to a quiz).

The number 5, PROG +, AUDIO and buttons have tactile dots. Use the tactile dots as references when operating the TV.

/ , the information on the

t Time is displayed t Information is hidden.

Overview of the TV buttons and indicators

HOME

1 (page 21) 2 / – Input select / OK

HOME

(only for KDL-40E4xxx, KDL-32E4xxx, KDL-26E4xxx)

• In TV mode: Selects the input source from equipment connected to the TV sockets (page 18).

• In TV menu: Selects the menu or option, and confirms the setting.

3 2 +/–//

• In TV mode: Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options right ( ) or left ( ).

4 PROG +/–//

• In TV mode: Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up ( ) or down ( ).

5 1 – Power

Turns the TV on or off.

To disconnect the TV completely, pull the plug from the mains.

6 Light Sensor

Do not put anything over the sensor, as its function may be affected.

7 Remote control sensor

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its function may be affected.

8 – Picture Off / Timer indicator

• Lights up in green when the picture is switched off (page 24).

• Lights up in orange when the timer is set (page 25).

9 1 – Standby indicator

Lights up in red when the TV is in standby mode.

0 " – Power / Timer REC programme indicator

• Lights up in green when the TV is turned on.

• Lights up in orange when the timer recording is set (page 15).

• Lights up in red during the timer recording.

• Make sure that the TV is completely turned off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

• Do not put anything over the indicators as their functions may be affected.

Watching TV

GUIDE

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Guide, see page 15.

In digital mode

An information banner appears briefly. The following icons may be indicated on the banner.

: Radio service : Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available : Subtitles available for the hearing impaired : Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

c: Current programme is being recorded

Watching TV

Additional operations

To Do this

Turn on the TV from Standby mode without sound

Adjust the volume Press 2 + (increase)/

Press %. Press 2 +/- to set the volume level.

- (decrease).

1 Press 1 on the TV to switch on the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

To access Text

Press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or PROG +/-. To hold a page, press / . To reveal hidden information, press / .

When four coloured items appear at the bottom of the Text page, Fastext is available. Fastext allows you to access pages quickly and easily. Press the corresponding coloured button to access the page.

To change the screen format manually to suit the broadcast

Press repeatedly to select the desired screen format.

Smart*

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen.

4:3

Displays conventional 4:3 broadcasts (e.g. non-wide screen TV) in the correct proportions.

Some characters and/or letters at the top and the bottom of the picture may not be visible in Smart mode. In such a case, you can select “Vertical Size” using the “Screen Settings” (page 26) menu and adjust vertical size to make it visible.

• When “Auto Format” is set to “On”, the TV will automatically select the best mode to suit the broadcast (page 26).

• You can adjust the position of the picture when selecting “Smart”, “14:9” or “Zoom”. Press down (e.g. to read subtitles).

F/f to move up or

Using the Options menu

Press OPTIONS to display the following options when viewing a TV programme.

Options Description

Picture Mode See page 22. Sound Effect See page 23. Speaker See page 27. Subtitle Setting (in

digital mode only) Sleep Timer See page 25. Power Saving See page 24. System Information (in

digital mode only)

See page 30.

See page 31.

Wide

Displays wide screen (16:9) broadcasts in the correct proportions.

Zoom*

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

14:9*

Displays 14:9 broadcasts in the correct proportions. As a result, black border areas are visible on the screen.

* Parts of the top and bottom of the picture may be cut off.

Checking the Guide *

All Categories

Tod ay

001 BBC ONE

002 BBC TWO

003 ITV1

004 Channel 4

005 Five

006 ITV2

007 BBC THREE

008 BBC FOUR

009 ITV3

010 SKY THREE

Select +/- 1 day on/off Event InformationTune

Fri 16 Mar 11:35

Homes Under the Hammer Neighbours Afterlife

Ready Steady Cook Extraordinary People: Britains Iden... CSI: Crime Scene Inv...

Dancing On Ice Exclusive Cracker

Sign Zone: Ancient Rome: The Rise a... The Jeremy Kyle... Homes Under th...

House Law and Order: Special Victims U... PartyPoker.com Worl...

Crime Hour: Midsomer Murders Vodafone TBA: L...

BBC Learning Zone: Schools: World P... A Picture of Br it... Eastenders

ER Real Crime: The Truth About the... This is BBC FOUR

Past Everybody Loves Raymond The Sharon Osb...

Racing from Chepstow and Ascot Baseball Wedne... Trans World Sport

13: 0012: 3012: 0011: 30

Category30 min ViewNextPrevious

Back

1 In digital mode, press GUIDE. 2 Perform the desired operation as shown in the

following table or displayed on the screen.

* This function may not be available in some countries/regions.

To Do this

Watch a programme Press F/f/G/g to select the programme, then press . Turn off the Guide Press Sort the programme information by

category – Category list

Set a programme to be recorded

1 Press the blue button. 2 Press

1 Press F/f/G/g to select the future programme you want to record,

– Timer REC

2 Press

GUIDE.

F/f to select a category, then press .

then press

/ .

F/f to select “Timer REC”.

3 Press to set the TV and your VCR/DVD recorder timers.

A c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

To record the programme you are currently watching, press / .

Set a programme to be displayed automatically on the screen when it starts – Reminder

1 Press F/f/G/g to select the future programme you want to

display, then press

F/f to select “Reminder”, then press .

2 Press

/ .

A c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.

Set the time and date of a programme you want to record – Manual timer REC

1 Press F/f/G/g to select the future programme you want to record,

then press

2 Press 3 Press

/ .

F/f to select “Manual timer REC”, then press . F/f to select the date, then press g.

4 Set the start and stop time in the same way as in step 3. 5 Press

F/f to select the programme, then press .

6 Press to set the TV and your VCR/ DVD recorder timers.

A c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

To record the programme you are currently watching, press / .

Watching TV

Continued

To Do this

Cancel a recording/reminder – Timer list

1 Press / .

F/f to select “Timer list”, then press .

2 Press 3 Press

F/f to select the programme you want to cancel, then press

F/f to select “Cancel Timer”, then press .

4 Press

A display appears to confirm that you want to cancel the programme.

5 Press G/g to select “Yes”, then press to confirm.

• You can set the timer record function on the TV to automatically operate the recorder only when the connected recorder is compatible with SmartLink. However, this feature may not operate with certain types of recorder, even though it is stated that the recorder is SmartLink compatible. For details please refer to the instruction manual supplied with your recorder.

• Once a recording has begun, you can switch the TV to standby mode, but do not turn off the TV completely or the recording may be cancelled.

• If an age restriction for programmes has been selected, a message asking for a PIN Code will appear on the screen. For details, see “Parental Lock” (page 31).

Using the Digital Favourite list *

Favourite Set-up

Favourites 1

Store Favourite

001 BBC ONE

002 BBC TWO

003 ITV1

004 Channel 4

005 Five

006 BBC Three

007 ITV2

008 Sky Sports

009 UKTV History

010 Channel 4+1

Enter Programme Number: - - -

011 More 4

012 abc1

013 QVC

014 UKTV Gold

015 The HITS

016 UKTV Bright Ideas

017 ftn

018 TMF

019 E4

020 E4+1

Favourites 2NextPrevious

Digital

Back

Digital Favourite list

* This function may not be available in some countries/regions.

To Do this

Create your Favourite list for the first time

1 Press F/f/G/g to select the channel you want to add, then press

Channels that are stored in the Favourite list are indicated by a symbol.

2 Press yellow key to select “Favourites 2” or “Favourites 3”.

Watch a channel

Turn off the Favourite list Add or remove channels in the currently

edited Favourite list

1 Press yellow key to navigate through favourite lists. 2 Press

F/f to select the channel, then press .

Press RETURN. 1 Press the blue button.

2 Press the yellow button to choose the list you want to edit. 3 Press

F/f/G/g to select the channel you want to add or remove,

then press .

1 In digital mode, press . 2 Perform the desired operation as shown in the

following table or displayed on the screen.

Remove all channels from the current Favourite list

1 Press the blue button. 2 Press the yellow button to select the favourite list you want to edit. 3 Press the blue button. 4 Press

G/g to select “Yes”, then press to confirm.

Using Optional Equipment

Connecting optional equipment

You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.

DVD player with

Video game equipment

DVD player

Decoder

DVD recorder

Decoder

component output

Hi-Fi audio equipment with optical audio input

VCR

Hi-Fi audio equipment

Audio system DVD player

PC (HDMI output) Blu-ray disc player

Digital video camera Digital decoder

Using Optional Equipment

CAM card

USB

For service use only

PC (HDMI output) Blu-ray disc player Digital video camera

DVC camcorder

Headphones

Viewing pictures from connected equipment

Switch on the connected equipment, then perform one of the following operation.

For equipment connected to the scart sockets using a fully-wired 21-pin scart lead

Start playback on the connected equipment. The picture from the connected equipment appears on the screen.

For an auto-tuned VCR/ DVD recorder

In analogue mode, press PROG +/-, or the number buttons, to select the video channel.

For other connected equipment

Press / to display a list of connected equipment. Press source, then press . The highlighted item is automatically selected if you do not perform any operation for two seconds after

pressing If you have set an input source to "Skip" in the "AV Preset" menu (page 27), that input source does not appear in the list.

To return to normal TV mode, press DIGITAL or ANALOG.

Symbol on the screen

AV1

AV2

AV3 To see the equipment connected to

HDMI 1* To see the equipment connected to

HDMI 2* To see the equipment connected to

F/f to select the desired input

Description

To see the equipment connected to A.

To see the equipment connected to B.

SmartLink is a direct link between the TV and a VCR/DVD recorder.

If the equipment has a DVI socket, connect the DVI socket to the HDMI IN socket through a DVIHDMI adaptor interface (not supplied), and connect the equipment’s audio out socket to the audio in HDMI IN socket.

Symbol on the screen

HDMI 3*

* ~

• Be sure to use only an authorized HDMI cable bearing the HDMI logo. We recommend that you use a Sony HDMI cable (high speed type).

• When “Control for HDMI” compatible equipment is connected, communication with the connected equipment is supported. Refer to page 19 to set up this communication.

• When connecting an audio system with HDMI socket,

be sure to also connect to the HiFi socket.

Component To see the equipmen t connected to

PC To see the equipment connected to

Description

To see the equipment connected to

It is recommended to use a PC cable with ferrites, such as the "Connector, D-sub 15" (ref. 1793-504-11, available in Sony Service Centre) or equivalent.

To connect Do this

Headphones M Connect to the i socket to listen to

sound from the TV on headphones.

Conditional Access Module (CAM) I

Hi-Fi audio equipment G

DIGITAL AUDIO OUT (OPTICAL) F

USB J Use USB memory to display photos.

Provides access to pay TV services. For details, refer to the instruction manual supplied with your CAM. To use the CAM, remove the “dummy” card from the CAM slot, then turn off the TV and insert your CAM card into the slot. When you are not using the CAM, we recommend that you keep the “dummy” card in the CAM slot.

CAM is not supported in all countries. Please check with your authorized dealer.

Connect to the audio output sockets

to listen to the sound from the

TV on Hi-Fi audio equipment. Use an optical audio cable.

Additional operations

To Do this

Return to normal TV mode

Press DIGITAL or ANALOG.

Using the Options menu

Press OPTIONS to display the following options when viewing pictures from connected equipment.

Options Description

Picture Mode (except PC input mode)

Display Mode (in PC input mode only)

Sound Effect See page 23. Speaker See page 27. PIP (in PC input

mode only) PAP (except PC input

mode) Auto Adjustment (in

PC input mode only) Horizontal Shift (in

PC input mode only)

See page 22.

See page 19.

See page 26.

To view two pictures simultaneously – PIP (Picture in Picture)

You can view two pictures (PC input and TV programme) on the screen simultaneously. Connect a PC (page 17), and make sure that images from a PC appear on the screen.

1 Press OPTIONS to display the Options

menu.

2 Press F/f to select “PIP”, then press .

The picture from the connected PC is displayed with full size and the TV programme is displayed on the right corner. You can use screen position.

F/f/G/g to move the TV programme

3 Press number buttons or PROG +/- to select

the TV channel.

To return to single picture mode Press RETURN.

You can switch the audible picture by selecting “PC Sound/TV Sound” from the Options menu.

Using Optional Equipment

Sleep Timer (except PC input mode)

Power Saving See page 24.

See page 25.

To view two pictures simultaneously – PAP (Picture and Picture)

You can view two pictures (external input and TV programme) on the screen simultaneously. Connect an optional equipment (page 17), and make sure that images from the equipment appear on the screen (page 18).

• This function is not available for a PC input source.

• You cannot change the size of the pictures.

• You cannot display analogue TV video in the TV programme picture while displaying AV1, AV2 or AV3 video in the external inputs picture.

1 Press OPTIONS. 2 Press F/f to select “PAP”, then press .

The picture from the connected equipment is displayed on the left, and the TV programme is displayed on the right.

3 Press the number buttons or PROG +/- to

select the TV channel.

To return to single picture mode

Press or RETURN.

The picture framed in green is audible. You can switch the audible picture by pressing G/g.

Using BRAVIA Sync (Control for HDMI)

The control for HDMI function enables the TV to communicate with the connected equipment that is compatible with the function, using HDMI CEC (Consumer Electronics Control). For example, by connecting Sony equipment that is compatible with control for HDMI (with HDMI cables), you can control them together. Be sure to connect the equipment correctly, and make the necessary settings.

Control for HDMI

• Automatically turns the connected equipment off when you turn the TV off.

• Automatically turns the TV on and switches the input to the connected equipment when the equipment starts to play.

• If you turn on a connected audio system while the TV is on, the sound output switches from the TV speaker to the audio system.

• Adjusts the volume (2 +/-) and mutes the sound (%) of a connected audio system.

• You can operate the connected Sony equipment that has the BRAVIA Sync logo by the TV remote by pressing:

– m/N/X/M/x to operate the connected

equipment directly.

Continued

– SYNC MENU to display the menu of the connected

HDMI equipment on the screen. After displaying the menu, you can operate the menu screen by using F/f/G/g and .

– OPTIONS to display “Device Control”, then select

options from “Menu”, “Options”, and “Content List” to operate the equipment.

– Refer to the instruction manual of the equipment for

available control.

To connect the equipment that is compatible with control for HDMI

Connect the compatible equipment and the TV with a HDMI cable. When connecting an audio system, be sure to also connect the DIGITAL AUDIO OUT (OPTICAL) socket of the TV and the audio system using an optical audio cable. For details, see page 18.

To make the control for HDMI settings

The control for HDMI settings must be set on both the TV side and connected equipment side. See HDMI Set-up on page 28 for the TV side settings. For settings on the connected equipment, refer to the operating instructions for that equipment.

Buttons for using optional equipment

Selection” is displayed when the button is pressed.

• Control for HDMI (BRAVIA Sync) is only

available with the connected Sony equipment that has the BRAVIA Sync logo or is compatible with control for HDMI.

• Sony BRAVIA Theatre Sync Products and

Control for HDMI compatible devices from other manufacturers may not support all functions.

GUIDE

1 m/N/X/M/x: You can operate the

BRAVIA Sync-compatible equipment that is connected to the TV.

2 THEATRE

You can set Theatre Mode on or off. When Theatre Mode is set to on, the optimum audio output (if the TV is connected with an audio system using an HDMI cable) and picture quality for film-based contents are automatically set.

If you turn the TV off, Theatre Mode is also turned off.

3 SYNC MENU: Displays the menu of connected

HDMI equipment. While viewing other input screens or TV programmes, “HDMI Device

Using MENU Functions

Overview of the TV Home Menu (XMB™)

The XMB™ (XrossMediaBar) is a menu of BRAVIA features and input sources displayed on the TV screen. The XMB™ is an easy way to select programming and adjust settings on your BRAVIA TV. Press the HOME button on your remote control to access the XMB™.

1 Press HOME.

The TV Home menu appears on the screen.

Instruction Manual

Picture

Media Category Bar

Settings

Sound

Features

Set-up

Analogue Set-up

Digital Set-up

Category Object Bar

2 Press G/g to select the category.

Media category icon Description

Settings You can make advanced settings and adjustments. For details about settings,

see page 22.

Photo You can select “USB Photo Viewer” or “Picture Frame” (page 32).

Digital You can select a digital channel, Favourite list (page 16), or Guide (page 15).

You can also select a channel using the number buttons or PROG +/–.

Analogue You can select an analogue channel.

You can also select a channel using the number buttons or PROG +/–. To hide the list of analogue channels, set “Programme List Display” to “Off” (page 28).

External Inputs You can select equipment connected to the TV.

To assign a label to an external input, see “AV Preset” (page 27).

Using MENU Functions

3 Press F/f to select the item, then press . 4 Follow the instructions on the screen. 5 Press HOME to exit.

• The options you can adjust vary depending on the situation.

• Unavailable options are greyed out or not displayed.

Settings

Instruction Manual

(Only for KDL-52W4xxx, KDL-46W4xxx, KDL-40W4xxx, KDL-32W4xxx, KDL-40E4xxx, KDL-32E4xxx)

Picture

Picture Mode

Display Mode

PC mode/ PC Input/ HDMI PC Input)

(only in

Displays contents of Instruction Manual on the screen. Use coloured buttons to move through the screens.

F/f/G/g to select , then press to go to related item or access real

Press application.

Selects the picture mode except for PC input source. The options for “Picture Mode” may differ depending on the “Video/Photo” setting (page 25).

“Vivid”: (“Shop”, see page 7). For enhanced picture contrast and sharpness. “Standard”: (“Home”, see page 7). For standard picture. Recommended for

home entertainment. “Cinema”: For viewing film-based content. Most suitable for viewing in a theatre-like environment. This picture setting was developed in collaboration with Sony Pictures Entertainment to faithfully reproduce movies as intended by their creators. “Photo”: Sets the optimum picture quality for photographs.

Selects the display mode for PC input source.

“Video”: For video images. “Text”: For text, charts or tables.

Reset

Backlight

Contrast

Brightness

Colour

Hue

Resets all picture settings except “Picture Mode” and “Display Mode” (only in PC mode) to the factory settings.

Adjusts the brightness of the backlight.

Increases or decreases picture contrast.

Brightens or darkens the picture.

Increases or decreases colour intensity.

Increases or decreases the green and red tones.

“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).

Colour Temperature

Adjusts the whiteness of the picture.

“Cool”: Gives the white colours a blue tint. “Neutral”: Gives the white colours a neutral tint. “Warm 1/Warm 2”: Gives white colours a red tint. “Warm 2” gives a redder

tint than “Warm 1”

“Warm 1 and Warm 2” are not available when “Picture Mode” is set to “Vivid”.

Sharpness

Noise Reduction

MPEG Noise Reduction

Advanced Settings

Sharpens or softens the picture.

Reduces the picture noise (snowy picture) in a weak broadcast signal.

“Auto”: Automatically reduces the picture noise (in analogue mode only). “High/Medium/Low”: Modifies the effect of the noise reduction. “Off”: Turns off the “Noise Reduction” feature.

“Auto” is not available for AV1, AV2, AV3, HDMI 1, HDMI 2, HDMI 3, Component, PC and digital mode.

Reduces the picture noise in MPEG-compressed video.

Customizes the Picture function in more detail. When you set “Picture Mode” to “Cinema” or “Standard”, you can set/change these settings. “Adv. Contrast Enhancer”: Automatically adjusts “Backlight” and “Contrast” to the most suitable settings judging from the brightness of the screen. This setting is especially effective for dark images scenes. It will increase the contrast distinction of the darker picture scenes.

“Live Colour”: Makes colours more vivid. “Colour Space” (except for KDL-32W4xxx, KDL-32E4xxx, KDL-26E4xxx, KDL-37V4xxx, KDL-32V4xxx, KDL-26V4xxx): Changes the colour

reproduction gamut. “Wide” reproduces the vivid colour and “Standard” reproduces the standard colour.

• “Live Colour” is not available when “Colour Space” is set to “Standard”.

• “Advanced Settings” is not available when “Picture Mode” is set to “Vivid”.

Using MENU Functions

“Noise Reduction”, “MPEG Noise Reduction” and “Advanced Settings” are not available for PC.

Sound

Sound Effect

Selects the sound effect. “Dynamic”: Intensifies clarity and sound presence for better intelligibility and musical realism by using the “BBE High definition Sound System.” “Standard”: Enhances clarity, detail, and sound presence by using “BBE High definition Sound System.”

“Clear Voice”: Makes voice sound clearer. “Dolby Virtual

by a multi channel system. “BBE ViVA”: BBE ViVA Sound provides musically accurate natural 3D image with Hi-Fi sound. The clarity of the sound is improved by BBE while the width depth and height of sound image are expanded by BBE’s proprietary 3D sound process. BBE ViVA Sound is compatible with all TV programs including news, music, dramas, movies, sports and electronic games.

• If you set “Auto Volume” to “On”, “Dolby Virtual” changes to “Standard”.

• If headphones are connected, “Sound Effect” changes to “Off”.

”

: Uses the TV speakers to simulate the surround effect produced

Reset

Resets all the sound settings to the factory settings.

Treble

Bass

Balance

Auto Volume

Volume Offset

Dual Sound

“Sound Effect”, “Treble”, “Bass”, “Balance” and “Auto Volume” are not available when “Speaker” is set to “Audio System”.

Adjusts higher-pitched sounds.

Adjusts lower-pitched sounds.

Emphasizes left or right speaker balance.

Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend to be louder than programmes).

If you set “Sound Effect” to “Dolby Virtual”, “Auto Volume” changes to “Off”.

Adjusts the volume level of the current input relative to other inputs.

Selects the sound from the speaker for a stereo or bilingual broadcast.

“Stereo/ Mono”: For a stereo broadcast. “A/ B/ Mono”: For a bilingual broadcast, select “A” for sound channel 1, “B”

for sound channel 2, or “Mono” for a mono channel, if available.

If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “A” or “B”.

Features

Quick Start

Power Saving

Light Sensor

Logo Illumination (except for KDL-37V4xxx,

KDL-32V4xxx, KDL-26V4xxx)

The TV turns on faster than usual within two hours after switching to standby mode. However, power consumption in standby mode is higher than usual.

Selects the power saving mode to reduce the power consumption of the TV. When “Picture Off” is selected, the picture is switched off and the (Picture Off) indicator on the TV front panel lights up in green. The sound remains unchanged.

“Standard Power”: Default settings. “Reduced Power”: Reduces the power consumption of the TV. “Picture Off”: Switches off the picture. You can listen to the sound with the

picture off.

“On”: Automatically optimises the picture settings according to the ambient light in the room. “Off”: Turns off the “Light Sensor” feature.

Be sure not to put anything over the sensor, as its function may be affected. See page 12 for the location of the light sensor.

Lights up and turns off the Sony logo on the front of the TV.

Film Mode

Provides an improved picture quality which is optimized for film when playing DVD images taken on film and non progressive (interlaced). “Auto”: Detects the picture contents (video or film) and optimizes the picture quality. Use this setting for standard use. “Off”: Turns off the “Film Mode” feature.

• If the image contains irregular signals or too much noise, “Film Mode” will be automatically turned off even if “Auto” is selected.

•“Film Mode” is not available when “Video/ Photo” is set to “Photo” or when photograph is detected if “Video-A” is set.

Video/Photo

x.v.Colour (except for KDL-32W4xxx,

KDL-32E4xxx, KDL-26E4xxx, KDL-37V4xxx, KDL-32V4xxx, KDL-26V4xxx)

Photo Colour Space (except for KDL-32W4xxx,

KDL-32E4xxx, KDL-26E4xxx, KDL-37V4xxx, KDL-32V4xxx, KDL-26V4xxx)

Provides suitable image quality by selecting the option depending on the input source (video or photograph data). “Video-A”: Sets suitable image quality, depending on the input source, video data or photograph data when directly connecting Sony HDMI output-capable equipment that supports “Video-A” mode.

“Video”: Produces suitable image quality for moving pictures. “Photo”: Produces suitable image quality for still images.

• The setting is fixed to “Video” when Video-A mode is not supported on the connected equipment, even if “Video-A” is selected.

• Only available for HDMI 1, HDMI 2, HDMI 3 and Component in format 1080i or 1080p.

Using MENU Functions

Displays moving pictures that is more faithful to the original source by matching the colour space of source.

• The setting is fixed to “Normal” when the input signal is HDMI (RGB), even if

“x.v.Colour” is selected.

• Only available for HDMI 1, HDMI 2, HDMI 3 and Component in format 720p,

1080i or 1080p.

Selects the option (sRGB, sYCC, Adobe RGB) to match the output colour space within the output signal from the equipment connected to the HDMI, component input jacks or USB.

• Select “sYCC” when using the equipment that supports “x.v.Colour”.

• Only available for HDMI 1, HDMI 2, HDMI 3 and Component in format 1080i

or 1080p.

• Not available when “Colour Space” is set to “Wide” (page 23).

Timer Settings

Sets the timer to turn on/off the TV.

Sleep Timer

Sets a period of time after which the TV automatically switches itself into standby mode. When the Sleep Timer is activated, the (Timer) indicator on the TV (front) lights up in orange.

• If you switch off the TV and switch it on again, “Sleep Timer” is reset to

“Off”.

• “Sleep timer will end soon. Power will be turned off” appears on the screen one

minute before the TV switches to standby mode.

Continued

Set-up

On Timer Settings

“On Timer”: Sets the timer to turn on the TV from standby mode. “Timer Mode”: Selects the desired period. “Time”: Sets the time to turn on the TV. “Duration”: Selects the time period after which the TV automatically switches

to standby mode again.

Clock Set

Allows you to adjust the clock manually. When the TV is receiving digital channels, the clock cannot be adjusted manually since it is set to the time code of the broadcasted signal.

Auto Start-up

Language

Screen Settings

PC Settings

Starts the “first time operation menu” to select the language, country/region and location, and tune in all available digital and analogue channels. Usually, you do not need to do this operation because the language and country/region will have been selected and channels already tuned when the TV was first installed (page 6). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).

Selects the language in which the menus are displayed.

“Screen Format”: For details about the screen format, see “To change the screen format manually to suit the broadcast” on page 14. “Auto Format”: Automatically changes the screen format according to the broadcast signal. To keep your setting, select “Off”. “Display Area”: Adjusts the picture display area in 1080i/p and 720p sources when "Screen Format" is set to "Wide".

• “Auto”: During digital broadcasts, displays pictures in accordance with the

settings recommended by the broadcast station.

• “Full Pixel”: Displays pictures in their original size.

• “Normal”: Displays pictures in their recommended size.

“Horizontal Shift”: Adjusts the horizontal position of the picture. “Vertical Shift”: Adjusts the vertical position of the picture when “Screen

Format” is set to “Smart”, “Zoom” or “14:9”. “Vertical Size”: Adjusts the vertical size of the picture when “Screen Format” is set to “Smart”.

“Screen Format”: Selects a screen format for displaying input from your PC.

• “Full 1”: Enlarges the picture to fill the vertical display area, keeping its

original horizontal-to-vertical aspect ratio.

• “Full 2”: Enlarges the picture to fill the display area.

“Reset”: Resets the PC screen settings to the factory settings. “Auto Adjustment”: Automatically adjusts the display position, phase and pitch

of the picture when the TV receives an input signal from the connected PC.

“Auto Adjustment” may not work well with certain input signals. In such cases, manually adjust “Phase”, “Pitch” and “Horizontal Shift”.

“Phase”: Adjusts the phase when the screen flickers. “Pitch”: Adjusts the pitch when the picture has unwanted vertical stripes. “Horizontal Shift”: Adjusts the horizontal position of the picture. “Power Management”: Switches the TV to standby mode if no signal is

received for 30 seconds in the PC input.

AV Set-up

“AV Preset”: Assigns a name to any equipment connected to the side and rear sockets. The name will be displayed briefly on the screen when the equipment is selected. You can skip an input source that is not connected to any equipment.

1 Press 2 Press

“AV2 Input”: Sets a signal to be input through the socket labelled / /

“AV2 Output”: Sets a signal to be output through the socket labelled /

other recording equipment to the / / AV2 socket, you can then record from the equipment connected to other sockets of the TV.

“Speaker”: Turns on/off the TV’s internal speakers.

“Audio Out”:

“Audio Out” is not available for audio system connected to the TV using the HDMI sockets.

F/f to select the desired input source, then press . F/f to select the desired option below, then press .

• -, CABLE, SAT, VCR, DVD/BD, GAME, AUDIO SYSTEM, CAM, PC: Uses one of the preset labels to assign a name to connected equipment.

• “Edit:”: Creates your own label.

1 Press F/f to select the desired letter or number (“_” for a blank space),

then press If you input a wrong character:

Press G/g to select the wrong character. Then, press F/f to select the correct character.

2 Repeat the procedure in step 1 until the name is completed. 3 Select “OK”, then press .

• “Skip”: Skips an input source that is not connected to any equipment when you press F/f to select the input source.

AV2 on the rear of the TV.

• “Auto”: Switches automatically among the signals of RGB input, S video

input, Composite video input depending on the input signal.

• “RGB”: Inputs the RGB signal.

• “S Video”: Inputs the S Video signal.

• “Composite”: Inputs the Composite video signal.

/ AV2 on the rear of the TV. If you connect a VCR/ DVD recorder or

• “TV”: Outputs a broadcast.

•“Auto”: Outputs whatever is being viewed on the screen (except signals from

the HDMI IN 1, HDMI IN 2, HDMI IN 3, / COMPONENT IN and

/ PC IN sockets).

• “TV Speaker”: The TV speakers are turned on in order to listen to the TV’s

sound through the TV speakers.

• “Audio System”: The TV speakers are turned off in order to listen to the

TV’s sound only through your external audio equipment connected to the audio output sockets. When connected with “Control for HDMI” compatible equipment, you can turn the connected equipment on interlocked with the TV. This setting must be made after connecting the equipment.

• “Variable”: The audio output from your audio system can be controlled by

the TV’s remote.

• “Fixed”: The audio output of the TV is fixed. Use your audio receiver’s

volume control to adjust the volume (and other audio settings) through your audio system.

Using MENU Functions

HDMI Set-up

This is used to set the “Control for HDMI” compatible equipment connected to the HDMI sockets. Note that the interlock setting must also be made on the connected “Control for HDMI” compatible equipment side. “Control for HDMI”: This sets whether to interlock the “Control for HDMI” compatible equipment and the TV. When set to “On”, the following menu items can be performed. However, power consumption in standby mode is higher than usual. “Auto Devices Off”: When this is set to “On”, the “Control for HDMI” compatible equipment turn on and off interlocked with the TV. “Auto TV On”: When this is set to “On” and if the connected HDMI, control compatible equipment is turned on, the TV automatically turns on, and the displays the HDMI input from the connected equipment. “Device List Update”: Creates or updates the “HDMI Device List”. Up to 14 “Control for HDMI” compatible equipment can be connected, and up to 4 equipment can be connected to a single socket. Be sure to update the “HDMI Device List” when you change the “Control for HDMI” compatible equipment connections or settings. Select them manually one by one until getting a correct picture for several seconds.

“HDMI Device List”: Displays the connected “Control for HDMI” compatible equipments.

Product Information

All Reset

Analogue Set-up

Programme List Display

Auto Tuning

Programme Sorting

Displays your TV’s product information.

Resets all settings to the factory settings and then displays the “Auto Start-up” screen.

• Be sure not to turn the TV off during this period (it takes about 30 seconds) or press any buttons.

• All settings, including Digital Favourite list, country/region, language, auto tuned channels, etc. will be reset.

Select “Off” to hide the list of analogue channels from the XMB™ (Xross Media Bar).

Tunes in all the available analogue channels. This option allows you to retune the TV after moving house, or to search for new channels that have been launched by broadcasters.

Changes the order in which the analogue channels are stored on the TV. 1 Press

F/f to select the channel you want to move to a new position, then

press .

F/f to select the new position for your channel, then press .

2 Press

Manual Programme Preset

Before selecting “Label/AFT/Audio Filter/LNA/Skip/Decoder”, press PROG +/– to select the programme number with the channel. You cannot select a programme number that is set to “Skip” (page 27).

Programme/System/Channel

Presets programme channels manually.

1 Press F/f to select “Programme”, then press . 2 Press

F/f to select the programme number you want to manually tune (if

tuning a VCR/ DVD recorder, select channel 00), then press RETURN.

F/f to select “System”, then press .

3 Press

4 Press F/f to select one of the following TV broadcast systems, then press

RETURN.

B/G: For western European countries/regions I: For the United Kingdom D/K: For eastern European countries/regions L: For France

5 Press F/f to select “Channel”, then press . 6 Press

F/f to select “S” (for cable channels) or “C” (for terrestrial channels),

then press

7 Tune the channels as follows:

If you do not know the channel number (frequency)

Press F/f to search for the next available channel. When a channel has been found, the search will stop. To continue searching, press

If you know the channel number (frequency)

Press the number buttons to enter the channel number of the broadcast you want or your

8 Press to jump to “Confirm”, then press . 9 Press

Repeat the procedure above to preset other channels manually.

Label

Assigns a name of your choice, up to five letters or numbers, to the selected channel. This name will be displayed briefly on the screen when the channel is selected. To input characters, follow steps 1 to 3 of “Edit:” (page 27).

AFT

Allows you to fine-tune the selected programme number manually if you feel that a slight tuning adjustment will improve the picture quality. You can adjust the fine tuning over a range of –15 to +15. When “On” is selected, the fine tuning is performed automatically.

F/f.

VCR/ DVD recorder channel number.

f to select “OK”, then press .

Using MENU Functions

Audio Filter

Improves the sound for individual channels in the case of distortion in mono broadcasts. Sometimes a non-standard broadcast signal can cause sound distortion or intermittent sound muting when watching mono programmes. If you do not experience any sound distortion, we recommend that you leave this option set to the factory setting “Off”.

You cannot receive stereo or dual sound when “Low” or “High” is selected.

LNA

Improves the picture quality for individual channels in the case of very weak broadcast signals (noisy picture). If you cannot see any improvement in the picture quality even if you set to “On”, set this option to “Off” (factory setting).

Skip

Skips unused analogue channels when you press PROG +/– to select channels. (You can still select a skipped channel using the number buttons.)

Decoder

Shows and records the scrambled channel selected when using a decoder connected directly to scart connector / AV1, or to scart connector

/ / AV2 via a VCR/DVD recorder.

Depending on the country/region selected for “Country” (page 7), this option may not be available.

Confirm

Saves changes made to the “Manual Programme Preset” settings.

Continued

Digital Set-up

Digital Tuning

Digital Auto Tuning

Tunes in the available digital channels. This option allows you to retune the TV after moving house, or to search for new channels that have been launched by broadcasters. For details, see “Auto-tunning the TV” (page 7).

Programme Sorting

Removes any unwanted digital channels stored on the TV, and changes the order of the digital channels stored on the TV.

1 Press

F/f to select the channel you want to remove or move to a new

position.

Press the number buttons to enter the known three-digit programme number of the broadcast you want.

2 Remove or change the order of the digital channels as follows:

To remove the digital channel

Press . After a confirmation message appears, press G to select “Yes”, then press

To change the order of the digital channels

Press g, then press F/f to select the new position for the channel and press G.

3 Press RETURN. Digital Manual Tuning

Tunes the digital channels manually. This feature is available when “Digital Auto Tuning” is set to “Antenna”.

1 Press the number button to select the channel number you want to manually

tune, then press

2 When the available channels are found, press

want to store, then press

F/f to select the programme number where you want to store the new

3 Press

channel, then press

Repeat the above procedure to manually tune other channels.

F/f to tune the channel.

F/f to select the channel you

Subtitle Set-up

Audio Set-up

“Subtitle Setting”: When “For Hard Of Hearing” is selected, some visual aids may also be displayed with the subtitles (if TV channels broadcast such information).

“Subtitle Language”: Selects which language subtitles are displayed in.

“Audio Type”: Switches to broadcast for the hearing impaired when “For Hard

Of Hearing” is selected. “Audio Language”: Selects the language used for a programme. Some digital channels may broadcast several audio languages for a programme. “Audio Description”: Provides audio description (narration) of visual information if TV channels broadcast such information.

“Mixing Level”

levels. “Dynamic Range”: Compensates for differences in the audio level between different channels. Note that this function may have no effect for some channels. “Optical Out”: Selects the audio signal that is output from the DIGITAL AUDIO OUT (OPTICAL) terminal on the rear of the TV. Set to “Auto” when equipment compatible with Dolby Digital is connected, and set to “PCM” when noncompatible equipment is connected.

*: Adjusts the TV main audio and Audio Description output

*This option is only available when “Audio Description” is set to “On”.

+ 185 hidden pages