Sony ICD-B10, ICD-B15 Operating Instructions

IC Recorder

Operating Instructions

3-230-616-11 (1)

ICD-B10/B15

2001 by Sony Corporation

For the customers in the United States

Owner’s Record

The model number is located at the rear and the serial number is located inside the battery compartment. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. Serial No.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Table of Contents

Before You Begin

What is an IC recorder? ................................................................................ 4

Features .......................................................................................................... 5

Getting Started

Step 1: Installing the Batteries ..................................................................... 6

Step 2: Setting the Clock............................................................................... 8

Basic Operations

Recording Messages ................................................................................... 10

Playing Back Messages............................................................................... 14

Playing Back the Specified Section Repeatedly — A-B Repeat ............ 18

Erasing Messages ........................................................................................ 19

Editing Messages

Adding a Recording ................................................................................... 21

Dividing a Message into Two/Combining Messages

— Index Function ................................................................................ 23

Moving Messages to a Different Folder

— Move Function ................................................................................ 26

Other Functions

Starting Recording at a Desired Time

— Timer Recording ............................................................................. 27

Playing Back a Message at a Desired Time with an Alarm ................... 30

Preventing Accidental Operation — HOLD function ........................... 33

Selecting the Display Mode ....................................................................... 34

Menu map .................................................................................................... 35

Changing the Settings ................................................................................ 36

Additional Information

Precautions ................................................................................................... 37

Troubleshooting .......................................................................................... 38

Index to Parts and Controls ....................................................................... 42

Specifications ............................................................................................... 45

Index ............................................................................................................. 46

BBefore You Begin

What is an IC recorder?

This IC recorder enables you to record and play back oral messages in the built-in IC memory.

z Recording

When a new message is recorded, it is automatically added after the last recorded messages. Unlike with tape recorders, you do not need to worry about recording over previously recorded messages by mistake. Since you do not need to search for the end of the last recording, you can start recording quickly whenever you wish.

11:30, November 1

Meet Mr. Brown at 2 p.m. tomorrow.

Message 1 Message 2 Message 3

Message 1 Message 2 Message 3 Message 4

z Playback

With this IC recorder, you can quickly locate the message you want to play back. Reviewing the current recording is also very easy.

z Erasing

You can quickly erase unwanted messages with an easy operation. When a message is erased, the next message automatically advances, leaving no blank space.

Message 1 Message 2 Message 5

Before

Erase Message 3

After

12:00, November 1 10:00, November 2

Don’t forget to call Mary

Make remittance at ABC bank

Message 3

9:00, November 4

Message 4

Message 4Message 1 Message 2 Message 3

Remaining messages are renumbered.

Send a card to Miss Smith

Features

• Maximum recording time ICD-B10: 63 min. (SP)/168 min. (LP) ICD-B15: 127 min. (SP)/339 min. (LP)

This unit is suitable for recording long meetings or lectures.

• Possible of recording up to 99 messages in each of 3 folders (ICD-

B10)/5 folders (ICD-B15)

• Alarm function (page 30)

You can start playing back a desired message with an alarm on a desired date and time.

• Timer recording function (page 27)

You can start recording automatically on a desired date and time.

• Index function (page 23)

You can add an index at the desired point during recording or playback to divide a message into two. You can also combine messages by erasing the index.

• Repeat play function (page 16, 18)

This unit can play back one message or the selected section repeatedly.

• Easy search function (page 17)

You can quickly search for the point (10 seconds ahead or 3 seconds back) and start playback.

• Playback speed control (page 16)

You can play back messages rapidly or slowly . This is useful when playing back a long recording such as a meeting.

• Advanced VOR function (page 13)

• Overwrite and additional recording functions (page 21)

You can overwrite after the desired point on a recorded message or add a new recording to a previously recorded message.

• External microphone jack (page 13)

Before You Begin

BGetting Started

Step 1: Installing the Batteries

1 Slide and lift the battery compartment lid.

2 Insert two LR03 (size AAA) alkaline batteries with correct

polarity, and close the lid.

If the battery compartment lid is accidentally detached, attach it as illustrated.

Clock setting display appears when you insert batteries for the first time, or when you insert batteries after the unit has been without batteries for a certain period of time. Please refer to Steps 2 to 4 in “Step 2: Setting the Clock” on pages 8 and 9 to set the date and time.

Replacing the batteries

The battery indicator on the display window shows the battery condition. When flashes, replace the batteries with new ones.

When flashes, the batteries are exhausted and the unit will stop operation.

Battery life*

With continuous use, approx. 7.5 hours (SP)/15 hours (LP) of recording or approx. 6 hours (SP)/8 hours (LP) of playback is possible.

* Using Sony alkaline batteries LR03 (SG) * When playing back through the internal speaker with VOL control at around 4

The battery life may shorten depending on the operation of the unit.

Notes

• Do not use manganese batteries for this unit.

• When you replace the batteries, insert the new ones within 3 minutes after you

removed the exhausted ones. Otherwise, the display may show the clock setting display or incorrect date and time when you re-insert the batteries. In this case, set the date and time again. The recorded messages and alarm setting, however, will remain.

• When replacing the batteries, be sure to replace both batteries with new ones.

• Do not charge dry batteries.

• When you are not going to use the unit for a long time, remove the batteries to

prevent damage from battery leakage and corrosion.

Note on the “ACCESS” message

When you insert the batteries, “ACCESS” may appear on the display window. Do not remove the batteries while this message is displayed. If the unit is required to process excessive amount of data, “ACCESS” may be displayed for an extended period of time. This is not a malfunction of the unit. Wait until the message disappears before starting operation.

Getting Started

Step 2: Setting the Clock

You need to set the clock to use the alarm or timer setting function. Clock setting display appears when you insert batteries for the first time, or when you insert batteries after the unit has been without batteries for a certain period of time. In this case, proceed from step 2.

NxPLAY/STOP

1 Press MENU to enter the menu mode. 2 Display the clock setting display.

1 Press .once to

display “SET DATE”.

2 Press NxPLAY/

STOP.

The year digits will flash.

3 Set the date.

1 Press . or >

to select the digits of the year.

2 Press NxPLAY/

STOP.

The month digits will flash.

./>

3 Set the month and

day in sequence, then press NxPLAY/STOP.

The hour digits will flash.

4 Set the time.

1 Press . or >

to select the digits of the hour.

2 Press NxPLAY/

STOP.

The minute digits will flash.

3 Set the minute.

5 Press NxPLAY/STOP at the time signal.

The display will return to “SET DATE”.

6 Press MENU to exit the menu mode.

1 Tip

This unit does not have a power on/off switch. The display is shown at all times.

Getting Started

BBasic Operations

Recording Messages

You can record up to 99 messages in each of three folders (A, B, or C) for ICD-B10 or five folders (A, B, C, D or E) for ICD-B15. Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording.

e.g. Message 1

Note

Before making a long recording, be sure to insert new batteries and check the battery indicator (page 7).

Press FOLDER repeatedly to display the folder in which you wish to record messages.

1 Press zREC/STOP.

Select the folder.

Start recording.

Remaining memory indicator

Counter display*

Message 2

Current message number

Newly recorded message

* The display selected with the DISPLAY button

(page 34) appears.

Blank space

Current folder

2 Speak to the built-in

microphone.

OPR indicator

(lights in red during recording.)

You do not need to keep pressing zREC/STOP while recording.

If you do not change the folder after you stop recording, the next time you record you will record in the same folder.

To stop recording

You can also stop recording by pressing xSTOP instead of zREC/STOP.

To pause recording

To Do this

pause recording* Press XPAUSE.

release pause and Press XPAUSE or zREC/STOP. resume recording Recording resumes from that point.

* 15 minutes after you pause recording, recording pause is automatically

released and the unit goes into the stop mode.

Stop recording.

Press zREC/STOP again.

The unit stops at the beginning of the current recording.

xSTOP

During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window.

(To stop recording after pausing recording, press xSTOP.)

Basic Operations

Continued

Recording Messages (continued)

To select the microphone sensitivity

See page 36.

Maximum recording time

With the ICD-B10, you can record for up to 63 minutes in SP (standard play) mode and 168 minutes in LP (long play) mode. If you record messages in a mixture of SP and LP modes, the recordable time varies from 63 to 168 minutes. With the ICD-B15, you can record for up to 127 minutes in SP (standard play) mode and 339 minutes in LP (long play) mode. If you record messages in a mixture of SP and LP modes, the recordable time varies from 127 to 339 minutes. The unit is factory-set to SP mode. To change the recording mode, see page 36. You can check the remaining amount of recording time by selecting the remaining recording time display mode. See page 34.

Remaining memory indication

During recording, the remaining memory indicator decreases one by one.

flashing

When the remaining time of recording reaches 5 minutes, the last one of the indication flashes. When the remaining time of recording reaches 1 minute, the selected display mode (page 34) and “REMAIN” will flash one after the other in the display window. When the memory is full, recording automatically stops and “FULL” will flash in the display window with an alarm sound. To continue recording, first erase some of the messages (page

19).

Various Ways of Recording

Starting recording automatically in response to the sound — Advanced VOR function

When the VOR (voice operated recording) function is set to ON (page 36), recording starts when the recorder detects sound and stops when no sound is heard.

Note

VOR function is affected by the sound around you. Set the microphone sensitivity (SENS) to either HI (high) or LO (low) (see page 36). If recording is not satisfactory after you have changed the microphone sensitivity, or for important recording, set VOR to OFF.

Recording with an external microphone or from other equipment

Connect a plug-in-power type microphone or other equipment to the MIC (PLUG IN POWER) jack. When you connect an external microphone, the built-in microphone is automatically cut off. When a plug-in-power type microphone is connected, power is automatically supplied to the microphone from the IC recorder.

Adding a recording

To add a recording to a previously recorded message or to add an overwrite recording during playback, see pages 21 and 22.

Basic Operations

Playing Back Messages

When playing back a previously recorded message, start from Step 1. When playing back a message you have just finished recording, start from Step 3.

Press FOLDER repeatedly to display the folder you wish to play back.

Press . or > to display the desired message number.

.: for smaller message number

>: for larger message number

* The display selected with the DISPLAY button (page 34) appears.

Select the folder.

Current folder

Select the message number.

Selected message number

Counter display*

1 Press NxPLAY/STOP.

After playing back one message, the unit stops at the beginning of the next message. When the last message on a folder has been played back, the unit stops at the beginning of the last message.

For private listening

Connect an earphone or headphones (not supplied) to the EAR jack. The builtin speaker will be automatically disconnected. If you plug in headphones, you will get monaural output from both left and right channels.

To stop playback

To Do this

stop at the beginning of Press xSTOP. the current message

stop at the current position Press NxPLAY/STOP.

* You can also pause playback by pressing XPAUSE instead of NxPLAY/

STOP. The OPR indicator will flash in green. After an hour, the unit goes into the stop mode at the current position.

Start playback.

Counter display (or the selected display mode)

(Playback Pause function)* To resume playback from that point, press NxPLAY/STOP again.

EAR jack

OPR indicator

(lights in green during playback.)

2 Turn VOL to adjust

the volume.

Basic Operations

Playing back all messages in a folder continuously — Continuous Play

See page 36.

Continued

+ 33 hidden pages