Sony HCD-HPR90, HCD-HPR99XM Service Manual

HCD-HPR90/HPR99XM

SERVICE MANUAL

Ver. 1.1 2006.05

• HCD-HPR90 is the amplifier, CD player and
tuner section in CMT-HPR90.

• HCD-HPR99XM is the amplifier, CD player
and tuner section in CMT-HPR99XM.

US and foreign patents licensed from Dolby Laboratories.

Photo: HCD-HPR90

US Model

Canadian Model

HCD-HPR90/HPR99XM

E Model

Australian Model

HCD-HPR90

Model Name Using Similar Mechanism NEW
CD Mechanism Name DLM5B
Base Unit Name BU-K6BD83S-WOD
Optical Pick-Up Block Name KSM-213DCP

Main unit

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORION:

US model

With 4 ohm loads, both channels driven, from 120 – 10,000 Hz; rated 85 watts
per channel minimum RMS power, with no more than 10% total harmonic

distortion from 250 milliwatts to rated output.

Amplifier section

North American model

DIN power output (rated): 68 + 68 W (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 85 + 85 W (4 ohms at 1 kHz,
10% THD)

The following measured at 127 V A C, 60Hz (Mexicam model),

AC 220 – 240 V, 50/60 Hz (Singapore, Argentina and Australian models),

AC 120 – 127 V or 220 – 240 V, 50/60 Hz (Other models)

DIN power output (rated): 56 + 56 W (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 70 + 70 W (4 ohms at 1 kHz,
10% THD)

Inputs

AUDIO IN: Sensitivity 250 mV, impedance of 47 kilohms

Outputs

PHONES (stereo mini jack): accepts headphones with an impedance of 8
ohms or more
SPEAKER: accepts impedance of 4 ohms

CD player section

System: Compact disc and digital audio system
Laser Diode Properties

Emission Duration: Continuous
Laser Output*: Less than 44.6 µW
* This output is the value measurement at a distance of 200 mm from the

objective lens surface on the Optical Pick-up Block with 7 mm aperture.
Frequency response: 20 Hz – 20 kHz (±2 dB)
Wavelength: 780 – 790 nm

SPECIFICATIONS

Tuner section

FM stereo, FM/AM superheterodyne tuner
FM tuner section:

Tuning range: 87.5 – 108.0 MHz
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz

AM tuner section:

Tuning range

Pan American model: 530 – 1,710 kHz (with 10 kHz tuning interval)

Other models: 530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,602 kHz (with 9 kHz tuning interval)
Antenna: AM loop antenna
Antenna terminals: External antenna terminal
Intermediate frequency: 450 kHz

General

Power requirements

North American model: 120V AC, 60 Hz
Mexican model: 127 V AC, 60 Hz
Singapore, Argentina and Australian models: 220 V – 240 V AC, 50/60 Hz
Other models: 120 – 127 V or 220 – 240 V AC, 50/60 Hz
Adjustable with voltage selector

Power consumption: 45 watts (HPR90)

Dimensions (w/h/d) (excl. speakers): Approx. 180 × 280 × 360 mm
Mass (excl. speakers): 3.9 kg (HPR90)

Design and specifications are subject to change
without notice.

531 – 1,710 kHz (with 9 kHz tuning interval)

50 watts (HPR99XM)

4.0 kg (HPR99XM)

9-887-115-02

2006E05-1
© 2006.05

COMPACT DISC RECEIVER

Sony Corporation

Personal Audio Division
Published by Sony Techno Create Corporation

HCD-HPR90/HPR99XM

r

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

CAUTION

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA
WT -540A. Follow the man ufacturers’ instructions to use these
instruments.

2. A battery-operated A C milliammeter . The Data Precision 245
digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated A C voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate lo w-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)

To Exposed Metal
Parts on Set

AC

0.15 µF

1.5 k

Ω

Earth Ground

voltmete
(0.75 V)

Fig. A. Using an AC voltmeter to check AC leakage.

ATTENTION AU COMPOSANT AYANT RAPPORT

LES COMPOSANTS IDENTIFIÉS P AR UNE MARQ UE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU D ANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.

À LA SÉCURITÉ!

2

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
P ART NUMBERS APPEAR AS SHOWN IN THIS MANU AL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 4

2. GENERAL ................................................................... 5

3. DISASSEMBLY

3-1. Disassembly Flow ........................................................... 7

3-2. Case ................................................................................. 8

3-3. Back Panel ....................................................................... 8

3-4. MAIN Board.................................................................... 9

3-5. AMP Board, POWER Board Section .............................. 9

3-6. Front Panel Section, CD Mechanical (DLM5B) ............. 10

3-7. Belt (DLM3A) ................................................................. 11

3-8. Optical Pick-Up Block .................................................... 11

4. TEST MODE.............................................................. 12

5. ELECTRICAL CHECK........................................... 14

6. DIAGRAMS

6-1. Block Diagram – CD SERVO Section – ......................... 15

6-2. Block Diagram – MAIN Section – .................................. 16

6-3. Block Diagram – AMP Section – .................................... 17

6-4. Block Diagram

– PANEL, POWER SUPPLY Section – .......................... 18

6-5. Printed Wiring Board – CD Board – ............................... 20

6-6. Schematic Diagram – CD Board – .................................. 21

6-7. Printed Wiring Board – MAIN Board – .......................... 22

6-8. Schematic Diagram – MAIN Section (1/3) – .................. 23

6-9. Schematic Diagram – MAIN Section (2/3) – .................. 24

6-10. Schematic Diagram – MAIN Section (3/3) – .................. 25

6-11. Printed Wiring Boards – XM Section (HPR99XM) – ..... 26

6-12. Schematic Diagram – XM Board (HPR99XM) – ........... 27

6-13. Printed Wiring Board – AMP Board – ............................ 28

6-14. Schematic Diagram – AMP Board – ............................... 29

6-15. Printed Wiring Board – PANEL Board – ........................ 30

6-16. Printed Wiring Boards – FL Section – ............................ 31

6-17. Schematic Diagram – PANEL Section – ......................... 32

6-18. Schematic Diagram – FL Board – ................................... 33

6-19. Printed Wiring Board – POWER Board – ....................... 34

6-20. Schematic Diagram – POWER Board –.......................... 35

HCD-HPR90/HPR99XM

7. EXPLODED VIEWS

7-1. Overall Section ................................................................ 52

7-2. Front Panel Section ......................................................... 53

7-3. AMP Board, POWER Board Section .............................. 54

7-4. CD Mechanical Section (DLM5B).................................. 55

8. ELECTRICAL PARTS LIST................................ 56

3

HCD-HPR90/HPR99XM

Ver. 1.1

SECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

MODEL IDENTIFICATION

— Rear Panel —

PART No.

MODEL PART No.

HPR90: US 2-670-257-0[]
HPR90: CND 2-670-257-1[]
HPR90: E 2-670-257-2[]
HPR90: MX 2-670-257-3[]
HPR90: E51 2-670-257-4[]
HPR90: AR 2-670-257-5[]
HPR90: SP 2-670-257-6[]
HPR90: AUS 2-670-257-7[]
HPR99XM: US 2-670-258-0[]
HPR99XM: CND 2-670-258-1[]

RELEASING THE ANTITHEFT LOCK

The disc table lock function for the antitheft of an demonstration
disc in the store is equipped.

Releasing Procedure :

1. Press the I/1 button to turn the power on.

2. While pressing the x button, press the Z button until
“UNLOCKED” displayed on the fluorescent indicator tube
(around 5 seconds).

Note: When “LOCKED” is displayed, the antitheft lock is not released by

turning power on/off with the I/1 button.

• Abbreviation

AR : Argentina model
AUS: Australian model
CND : Canadian model
E51 : Chilean and Peruvian models
MX : Mexican model
SP : Singapore model

4

– HPR90 –

SECTION 2

GENERAL

HCD-HPR90/HPR99XM

This section is extracted from
instruction manual.

Basic Operations

12345

ws

wg

9

.

1
ws
qa

wd
w;
6

qk
9

qj
4

7

wf

.

ql

on the remote

6
7

8
9

q;

side

wa
w;
ql
qk
qj
qh
qg

qf qd qs qa

wl
3

wk
qs
ql
wa

wj

wh
wg

wf

Before using the system

To use the remote

Slide and remove the battery compartment lid , and
insert the two supplied R6 (size AA) batteries,
first, matching the polarities shown below.

Notes on using the remote

• With normal use, the batteries should last for about six months.

• Do not mix an old battery with a new one or mix different types of
batteries.

• If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.

To set the clock

1

Turn on the system.

Press

(power) .

2

Select the clock set mode.

Press CLOCK/TIMER SET on the remote. If the
current mode appears on the display, press

on the remote repeatedly to select “CLOCK SET”

and then press ENTER on the remote.

3

Set the time.

Press
the hour, and then press ENTER on the remote.
Use the same procedure to set the minute.
When you turn off the system after setting the clock,
the clock display appears instead of the demonstration
display.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.

Selecting a music source

Press the following buttons (or press FUNCTION on
the remote repeatedly).

To select Press

CD CD on the remote.
Tuner TUNER/BAND
Component (connected

using an audio cord)

9

/ on the remote repeatedly to set

AUDIO IN .

Adjusting the sound

To adjust the volume

Press VOLUME +/– on the remote (or turn the
VOLUME control on the unit)

To add a sound effect

To Press

Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)

Set the sound effect

DSGX on the unit.

EQ on the remote
repeatedly to select “BASS”
or “TREBLE,” and then
press +/–
repeatedly to adjust the level.

Playing a CD/MP3 disc

1

Select the CD function.

Press CD

on the remote.

2

Place a disc.

Press

(CD open/close) on the unit, and place a

disc with the label side up on the disc tray.

To insert additional discs, slide the disc tray with your
finger as shown below.

To close the disc tray, press (CD open/close) on
the unit again.
Do not force the disc tray closed with your finger, as
this may damage the unit.

3

Start playback.

Press

(play) on the remote (or CD/ (play/

wj

pause)

on the unit).

To Press

Pause playback

Stop playback
Select a folder on an

MP3 disc

Select a track or file

Find a point in a
track or file

Select Repeat Play

Select a disc DISC SKIP

Switch to CD
function from
another source

Exchange other
discs while playing

To change the play mode

Press PLAY MODE repeatedly while the player is

/

stopped. You can select normal play (“ALL DISCS” for
all discs, “1DISC” for a disc, or “
in the folder on the disc), shuffle play (“ALL DISCS
SHUF,” “1DISC SHUF,” or “
play (“PGM”).

* When playing a CD-DA disc, (SHUF) Play performs the same

operation as 1DISC (SHUF) Play.

Note on the jog dial

Only the first 6 characters are displayed when performing the folder
search, track search, or file search.

Notes on Repeat Play

• All tracks or files on a disc are played repeatedly up to five times.

• You cannot select “REP” and “ALL DISCS SHUF” at the same
time.

• “REP 1” indicates that a single track or file is repeated until you
stop it.

Notes on playing MP3 discs

• Do not save other types of files or unnecessary folders on a disc that
has MP3 files.

• Folders that have no MP3 files are skipped.

• MP3 files are played back in the order that they are recorded onto
the disc.

• The system can only play MP3 files that have a file extension of
“.MP3.”

• If there are files on the disc that have the “.MP3” file extension,
but that are not MP3 files, the unit may produce noise or may
malfunction.

• The maximum number of:
– folders is 255 (including the root folder).
– MP3 files is 511.

MP3 files and folders that can be contained on a single disc is 512.

–
– folder levels (the tree structure of files) is 8.

• Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.

Notes on playing multisession discs

• If the disc begins with a CD-DA (or MP3) session, it is recognized
as a CD-DA (or MP3) disc, and other sessions are not played back.

• A disc with a mixed CD format is recognized as a CD-DA (audio)
disc.

(pause) on the remote (or
CD/
unit). To resume play, press the
button again.

(stop) .

+/– (select folder) . Or
turn the jog dial
and press PUSH ENTER
the unit (turn the jog dial
the unit during playback until
“GROUP” appears, and then
press PUSH ENTER
unit to select the desired folder).

. Or turn the jog dial on

the unit and press PUSH ENTER

on the unit. To cancel, press

CANCEL
Hold down

forward)
and release the button at the
desired point.

REPEAT
“REP” or “REP1” appears.

DISC 1 – 5
(in stop mode) on the unit).

DISC 1 – 5
(Automatic Source Selection).

EX-CHANGE

wj

(play/pause) on the

on the unit

on the

/ (go back/go forward)

on the unit.

/ (rewind/fast

during playback,

repeatedly until

on the remote (or
or DISC SKIP

on the unit

on the unit.

*” for all MP3 files

SHUF*”), or program

Listening to the radio

1

Select “FM” or “AM.”

Press TUNER/BAND

2

Select the tuning mode.

Press TUNING MODE
appears.

3

Tune in the desired station.

Press +/– on the remote (or TUNING +/– on the unit)

. Scanning stops automatically when a station is
tuned in, and then “TUNED” and “STEREO” (for
stereo programs) appear.

To stop automatic scanning

Press (stop) .

To tune in a station with a weak signal

If “TUNED” does not appear and the scanning does
not stop, press TUNING MODE
“AUTO” and “PRESET” disappear, and then press
+/– on the remote (or TUNING +/– on the unit)
repeatedly to tune in the desired station.

To reduce static noise on a weak FM stereo
station

Press FM MODE repeatedly until “MONO” appears
to turn off stereo reception.

repeatedly.

repeatedly until “AUTO”

Changing the display

To change Press

Information on

DISPLAY repeatedly when the

the display*

system is on.

Display mode

DISPLAY

(See below.)

system is off.

* For example, you can view CD/MP3 disc information, such as the

track or file number or folder name during normal play, or the total
play time while the player is stopped.

The system offers the following display modes.

on

Display mode When the system is off,

on

Demonstration The clock display is replaced by

lighting and flashing of the display

window.
Clock The clock is displayed.
Power Saving

The display is turned off to conserve

2)

Mode

power. The timer and clock continue

to operate.

1)

The STANDBY indicator lights up when the system is off.

2)

When the system is in Power Saving Mode, the following functions
are unavailable:
– setting the clock
– changing the AM tuning interval
– changing the CD power manage function

Notes on the display information

• The following are not displayed;

– total playing time for a CD-DA disc depending on the play mode.
– total playing time for an MP3 disc.
– remaining playing time for an MP3 file.

• The following are not displayed correctly;

– elapsed playing time of an MP3 file encoded using a VBR

(variable bit rate).

– folder and file names that do not follow either the ISO9660 Level

1, Level 2 or Joliet in the expansion format.

• The following are displayed;

– ID3 tag information for MP3 files when ID3 version 1 and version

2 tags are used.

– up to 62 characters of ID3 tag information using uppercase letters

(A to Z), numbers (0 to 9), and symbols (" $ % ’ ( ) * + , – . / < =
> @ [ \ ] _ ` { | } ! ? ^).

Using optional audio
components

To connect an optional headphones

Connect headphones to the PHONES jack on the
unit.

To connect an optional component

Connect additional audio component to the AUDIO
IN jack

on the unit using an audio analog cord (not
supplied). Turn down the volume on the system, and then
press FUNCTION
the AUDIO IN function.

on the remote repeatedly to select

repeatedly until

repeatedly when the

1)

Other Operations

Creating your own CD program

(Program Play)

Use buttons on the remote to create your own program.

1

Press CD to select the CD function.

2

Press PLAY MODE repeatedly until “PGM”
appears while the player is stopped.

3

Press DISC SKIP to select a disc.

4

Press / repeatedly or turn the jog
dial

on the unit until the desired track number

appears.

When programming MP3 files, press

repeatedly or turn the jog dial on the

folder)
unit to select the desired folder, and then select the
desired file.

Current disc

Selected track

Total playing time of program

or file number

(including selected track or file)

Loaded disc

5

Press ENTER to add the track or file to the

9

program.

“– –.– –” appears when the total time exceeds 100
minutes for a CD, or when you select a CD track
whose number is 21 or over, or when you select an
MP3 file.

6

Repeat steps 4 through 5 to program additional
tracks or files, up to a total of 25 tracks or files.

7

To play your program of tracks or files, press
(play) .

wj

The program remains available until you open the disc
tray. To play the same program again, select the CD
function, and press

To cancel Program Play

Press PLAY MODE repeatedly until “PGM”
disappears while the player is stopped.

To delete the last track or file of the program

Press CLEAR while the player is stopped.

To view program information, such as total
track number of the program

Press DISPLAY repeatedly.

Tip

You can program additional tracks or files during playback by using
the jog dial.

Presetting radio stations

You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.

1

Tune in the desired station (see “Listening to the
radio”).

2

Press TUNER MEMORY .

3

Press +/– repeatedly to select your desired
preset number.

If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.

4

Press ENTER .

5

Repeat steps 1 through 4 to store other stations.

You can preset up to 20 FM and 10 AM stations. The
preset stations are retained for about half a day even
if you disconnect the power cord or if a power failure
occurs.

6

To call up a preset radio station, press TUNING
MODE
and then press +/–
desired preset number.

(play) .

wh

9

repeatedly until “PRESET” appears,

repeatedly to select the

wj

wk

+/– (select

Preset number

Using the Timers

The system offers two timer functions. If you use Play
Timer with the Sleep Timer, the Sleep Timer has priority.

Sleep Timer:

You can fall asleep to music. This function works even if
the clock is not set.

wl

Press SLEEP on the remote repeatedly. If you select
“AUTO,” the system automatically turns off after the
current disc stops or in 100 minutes.

Play Timer:

You can wake up to CD or tuner at a preset time.
Use buttons on the remote to control the Play Timer.

Make sure you have set the clock.

1

Prepare the sound source.

Prepare the sound source, and then press VOLUME
+/–

to adjust the volume.
To start from a specific CD track or MP3 file, create
your own CD program.

2

Press CLOCK/TIMER SET .

3

Press / repeatedly to select “PLAY
SET” then press ENTER .

“ON” appears, and the hour indication flashes.

4

Set the time to start playing.

Press

/ repeatedly to set the hour,

and then press ENTER .

The minute indication flashes. Use the procedure
above to set the minute.

5

Use the same procedure as in step 4 to set the
time to stop playing.

6

Select the sound source.

/ repeatedly until the desired

Press
sound source appears, and then press ENTER . The
display shows the timer settings.

7

Press (power) to turn off the system.

The system turns on 15 seconds before the preset
time.
If the system is on at the preset time, the Play Timer
will not play.

To activate or check the timer again

Press CLOCK/TIMER SELECT , press /

repeatedly until “PLAY SEL” appears, and then press

ENTER .

9

To cancel the timer

Repeat the same procedure as above until “TIMER OFF”
appears, and then press ENTER .

To change the setting

Start over from step 1.

Tip

The Play Timer setting remains as long as the setting is not canceled
manually.

ws

9

9

9

ws

9

5

HCD-HPR90/HPR99XM

– HPR99XM –

Basic Operations

Before using the system

To use the remote

Slide and remove the battery compartment lid , and
insert the two supplied R6 (size AA) batteries,
first, matching the polarities shown below.

Notes on using the remote

• With normal use, the batteries should last for about six months.

• Do not mix an old battery with a new one or mix different types of
batteries.

• If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.

To receive the XM Satellite Radio

Introducing XM Satellite Radio

XM Radio is the satellite radio service with millions of listeners
across the U.S. Broadcasting live daily. XM Radio offers 160
digital radio channels offering music, news, sports, comedy, talk,
entertainment, traffic and weather reports, with high quality digital
sound.

How to Subscribe

XM $12.95 monthly service subscription sold separately. XM
Connect and Play (TM) antenna required to receive XM service (sold
separately). Installation costs and other fees and taxes, including a
one-time activation fee may apply. Subscription fee is consumer only.
All fees and programming subject to change. Channels with frequent
explicit language are indicated with an XL. Channel blocking is
available for XM radio receivers by calling 1-800-XMRADIO.
Subscriptions subject to Customer Agreement available
at xmradio.com. XM service only available in the 48 contiguous
United States. XM Ready and XM Connect-and-Play are trademarks
of XM Satellite Radio Inc. (C)2005 XM Satellite Radio Inc. All rights
reserved.

Activate XM Service

Find the 8-character XM Radio ID of the Connect-and-Play antenna.
With the Connect-and-Play antenna connected to the unit, the Radio
ID can be found by selecting channel 0 on the radio. Press >10, 10/0,

on the remote in that order to select channel 0.

10/0, 10/0
Record the Radio ID here for reference: _______________________.
(NOTE: The XM Radio ID does not use the letters I, O, S, or F.)
Activate your XM Satellite Radio service online
at http://activate.xmradio.com or by calling 1-800-XMRADIO
(1-800-967-2346). You will need a major credit card.
XM will send a signal from the satellites to activate the full channel
lineup. Activation normally takes 10 to 15 minutes, but during peak
busy periods, you may need to keep your player on for up to an hour.
When you can access the full channel lineup on your player, you’re
done.

Notes on XM Satellite Radio

• To ensure optimal reception of XM’s satellite signal, move your
antenna to various window locations around your home to see
where the best reception will be received. Most XM customers
place the antenna in a south-facing window with a clear view to the
sky.

• Residents in Canada please see information about XM Canada at
the following webpage: (http://www.xmradio.ca/)

To set the clock

1

Turn on the system.

(power) .

Press

2

Select the clock set mode.

Press CLOCK/TIMER SET on the remote. If the
current mode appears on the display, press

on the remote repeatedly to select “CLOCK SET”

and then press ENTER on the remote.

3

Set the time.

Press
the hour, and then press ENTER on the remote.
Use the same procedure to set the minute.
When you turn off the system after setting the clock,
the clock display appears instead of the demonstration
display.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.

Selecting a music source

Press the following buttons (or press FUNCTION on
the remote repeatedly).

To select Press

CD CD on the remote.
Tuner TUNER/BAND
Component (connected

using an audio cord)

8

/ on the remote repeatedly to set

AUDIO IN .

wd

side

ws

/

8

.

qk

Adjusting the sound

To adjust the volume

Press VOLUME +/– on the remote (or turn the
VOLUME control on the unit)

To add a sound effect

To Press

Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)

Set the sound effect

.

DSGX

on the unit.

EQ on the remote

ql

repeatedly to select “BASS”
or “TREBLE,” and then
press +/–

on the remote

repeatedly to adjust the level.

Playing a CD/ATRAC/MP3 disc

1

Select the CD function.

on the remote.

Press CD

2

Place a disc.

Press

(CD open/close) on the unit, and place a

disc with the label side up on the disc tray.

To insert additional discs, slide the disc tray with your
finger as shown below.

To close the disc tray, press (CD open/close) on
the unit again.
Do not force the disc tray closed with your finger, as
this may damage the unit.

3

Start playback.

Press

(play) on the remote (or CD/ (play/

wa

pause)

on the unit).

To Press

Pause playback

Stop playback
Select a folder on

an “ATRAC” disc or
MP3 disc

Select a track or file

Find a point in a
track or file

Select Repeat Play

Select a disc DISC SKIP

Switch to CD
function from
another source

Exchange other
discs while playing

To change the play mode

Press PLAY MODE repeatedly while the player is
stopped. You can select normal play (“ALL DISCS” for
all discs, “1DISC” for a disc, or “
files and MP3 files in the folder on the disc), shuffle
play (“ALL DISCS SHUF,” “1DISC SHUF,” or “
SHUF*”), or program play (“PGM”).

* When playing a CD-DA disc, (SHUF) Play performs the same

operation as 1DISC (SHUF) Play.

To select a CD track using the number
buttons

Press the number buttons on the remote during
normal play. For example, to enter 20, press >10, 2, 10/0,
in that order.

To create an “ATRAC”/MP3 disc

You can create an “ATRAC” disc and MP3 disc with the
SonicStage software. SonicStage can be
downloaded free of charge from the following sites and
installed on your computer.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
<http://www.sony.ca/ElectronicsSupport/>
Please see the instructions at the sites or SonicStage Help
of the software for how to install and how to create an
“ATRAC”/MP3 disc.

Note on the jog dial

Only the first 6 characters are displayed when performing the folder
search, track search, or file search.

Notes on Repeat Play

• All tracks or files on a disc are played repeatedly up to five times.

• You cannot select “REP” and “ALL DISCS SHUF” at the same
time.

• “REP 1” indicates that a single track or file is repeated until you
stop it.

Notes on playing MP3 discs

• Do not save other types of files or unnecessary folders on a disc that
has “ATRAC” and MP3 files.

• Folders that have no “ATRAC” and MP3 files are skipped.

• “ATRAC” and MP3 files are played back in the order that they are
recorded onto the disc.

• The system can only play MP3 files that have a file extension of
“.MP3.”

• If there are files on the disc that have the “.MP3” file extension,
but that are not MP3 files, the unit may produce noise or may
malfunction.

• The maximum number of:
– “ATRAC” folders is 255.
– “ATRAC” files is 999.
– MP3 folders is 255 (including the root folder).
– MP3 files is 511.
–

MP3 files and folders that can be contained on a single disc is 512.

– folder levels (the tree structure of files) is 8.

wa

(pause) on the remote (or

CD/

(play/pause) on the
unit). To resume play, press the
button again.

(stop) .

+/– (select folder) . Or

turn the jog dial

on the unit
and press PUSH ENTER
the unit (turn the jog dial
the unit during playback until
“GROUP” appears, and then
press PUSH ENTER
unit to select the desired folder).

/ (go back/go forward)

. Or turn the jog dial on

the unit and press PUSH ENTER

on the unit. To cancel, press

CANCEL
Hold down

forward)
and release the button at the
desired point.

REPEAT
“REP” or “REP1” appears.

DISC 1 – 5
(in stop mode) on the unit).

DISC 1 – 5
(Automatic Source Selection).

EX-CHANGE

on the

on the unit.

/ (rewind/fast

during playback,

repeatedly until

on the remote (or

or DISC SKIP

on the unit

on the unit.

*” for all “ATRAC”

on
on

• Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.

• If “ATRAC” files and MP3 files are recorded on the same disc, this
system plays the “ATRAC” files first.

Notes on playing multisession discs

• If the disc begins with a CD-DA (or “ATRAC”/MP3) session, it is
recognized as a CD-DA (or “ATRAC”/MP3) disc, and other sessions
are not played back.

• A disc with a mixed CD format is recognized as a CD-DA (audio)
disc.

Listening to the radio

To listen to FM or AM

1

Select “FM” or “AM.”

Press TUNER/BAND

2

Select the tuning mode.

Press TUNING MODE
appears.

3

Tune in the desired station.

Press +/– on the remote (or TUNING +/– on the unit)

. Scanning stops automatically when a station is
tuned in, and then “TUNED” and “STEREO” (for
stereo programs) appear.

To stop automatic scanning

Press (stop) .

To tune in a station with a weak signal

If “TUNED” does not appear and the scanning does
not stop, press TUNING MODE
“AUTO” and “PRESET” disappear, and then press
+/– on the remote (or TUNING +/– on the unit)
repeatedly to tune in the desired station.

To reduce static noise on a weak FM stereo
station

Press FM MODE repeatedly until “MONO” appears
to turn off stereo reception.

To listen to XM

You can operate and listen to the XM satellite Radio by
connecting your XM Connect-and-Play antenna. Before
using the system, connect the XM Connect-and-Play
antenna to the XM jack of the system (see “Hooking up
the system securely”).

1

Select “XM.”

Press XM on the remote (or TUNER/BAND
repeatedly) .

2

Select the All Channel mode.

Press TUNING MODE repeatedly until “CAT”
and “PRESET” disappear.

3

Tune in the desired channel.

Press +/– on the remote (or TUNING+/– on the unit)

6

repeatedly.

To select a channel by Category mode

1

Press XM on the remote (or TUNER/BAND
repeatedly) .

2

Press TUNING MODE repeatedly until “CAT”
appears.

3

Press CATEGORY +/– on the remote (or CAT
+/– on the unit) repeatedly.

4

Press +/– on the remote (or TUNING +/– on the

6

unit) repeatedly.

To select a channel using the number
buttons

Press the number buttons on the remote. For example,
to enter 20, press >10, 10/0, 2, 10/0, in that order. You
cannot enter 255 or more.

Notes

• If you select a channel that is not broadcasted, “OFF AIR” appears
and the previous channel is selected.

• If you select a channel using the number buttons in Category mode,
the tuning mode changes to All Channel mode automatically.

qk

qk

6

repeatedly.

repeatedly until “AUTO”

repeatedly until

qa

qa

wh

Changing the display

To change Press

Information on
the display*

Display mode
(See below.)

* For example, you can view CD/“ATRAC”/MP3 disc information,

The system offers the following display modes.

Display mode When the system is off,

Demonstration The clock display is replaced by

Clock The clock is displayed.
Power Saving

Mode

1)

2)

Notes on the display information

• The following are not displayed;

• The following are not displayed correctly;

• The following are displayed;

Using optional audio
components

To connect an optional headphones

Connect headphones to the PHONES jack on the
unit.

To connect an optional component

Connect additional audio component to the AUDIO
IN jack
supplied). Turn down the volume on the system, and then
press FUNCTION
the AUDIO IN function.

DISPLAY repeatedly when the
system is on.

DISPLAY

repeatedly when the

system is off.

such as the track or file number or folder name during normal play,
or the total play time while the player is stopped. You can also view
XM radio information, such as the channel name, song title and
artist name.

1)

lighting and flashing of the display
window.

The display is turned off to conserve

2)

power. The timer and clock continue
to operate.

The STANDBY indicator lights up when the system is off.
When the system is in Power Saving Mode, the following functions

are unavailable:
– setting the clock
– changing the AM tuning interval
– changing the CD power manage function

– total playing time for a CD-DA disc depending on the play mode.
– total playing time for an “ATRAC”/MP3 disc.
– remaining playing time for an MP3 file.

– elapsed playing time of an “ATRAC” file or MP3 file encoded

using a VBR (variable bit rate).

– folder and file names that do not follow either the ISO9660 Level

1, Level 2 or Joliet in the expansion format.

– ID3 tag information for “ATRAC” files and MP3 files when ID3

version 1 and version 2 tags are used.

– up to 62 characters of ID3 tag information using uppercase letters

(A to Z), numbers (0 to 9), and symbols (" $ % ’ ( ) * + , – . / < =
> @ [ \ ] _ ` { | } ! ? ^).

on the unit using an audio analog cord (not

on the remote repeatedly to select

Other Operations

Creating your own CD program

(Program Play)

Use buttons on the remote to create your own program.

1

Press CD to select the CD function.

2

Press PLAY MODE repeatedly until “PGM”
appears while the player is stopped.

3

Press DISC SKIP to select a disc.

4

Press / repeatedly or turn the jog
dial

on the unit until the desired track number

appears.

When programming “ATRAC” files or MP3 files,

+/– (select folder) repeatedly or turn the

press
jog dial

on the unit to select the desired folder, and

then select the desired file.

Current disc

Selected track

Total playing time of program

or file number

(including selected track or file)

Loaded disc

5

Press ENTER to add the track or file to the

8

program.

“– –.– –” appears when the total time exceeds 100
minutes for a CD, or when you select a CD track
whose number is 21 or over, or when you select an
“ATRAC” file or MP3 file.

6

Repeat steps 4 through 5 to program additional
tracks or files, up to a total of 25 tracks or files.

7

To play your program of tracks or files, press
(play) .

wa

The program remains available until you open the disc
tray. To play the same program again, select the CD
function, and press

To cancel Program Play

Press PLAY MODE repeatedly until “PGM”
disappears while the player is stopped.

To delete the last track or file of the program

Press CLEAR while the player is stopped.

To view program information, such as total
track number of the program

Press DISPLAY repeatedly.

Tip

You can program additional tracks or files during playback by using
the jog dial.

Presetting radio stations

You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.

1

Tune in the desired station (see “Listening to the
radio”).

2

Press TUNER MEMORY .

3

Press +/– repeatedly to select your desired
preset number.

If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.

4

Press ENTER .

5

Repeat steps 1 through 4 to store other stations.

You can preset up to 20 FM, 10 AM and 20 XM
stations. The preset stations are retained for about half
a day even if you disconnect the power cord or if a
power failure occurs.

6

To call up a preset radio station, press TUNING
MODE
and then press +/–
desired preset number.

Note on presetting XM stations

You cannot preset XM stations except when you receive the station.

Using the Timers

The system offers two timer functions. If you use Play
Timer with the Sleep Timer, the Sleep Timer has priority.

Sleep Timer:

You can fall asleep to music. This function works even if
the clock is not set.

Press SLEEP on the remote repeatedly. If you select
“AUTO,” the system automatically turns off after the
current disc stops or in 100 minutes.

Play Timer:

You can wake up to CD or tuner at a preset time.
Use buttons on the remote to control the Play Timer.

Make sure you have set the clock.

1

Prepare the sound source.

Prepare the sound source, and then press VOLUME
+/–

to adjust the volume.
To start from a specific CD track, “ATRAC” file or
MP3 file, create your own CD program.

2

Press CLOCK/TIMER SET .

3

Press / repeatedly to select “PLAY
SET” then press ENTER .

“ON” appears, and the hour indication flashes.

4

Set the time to start playing.

Press

and then press ENTER .

The minute indication flashes. Use the procedure
above to set the minute.

5

Use the same procedure as in step 4 to set the
time to stop playing.

6

Select the sound source.

Press
sound source appears, and then press ENTER . The
display shows the timer settings.

7

Press (power) to turn off the system.

The system turns on 15 seconds before the preset
time. If the system is on at the preset time, the Play
Timer will not play.

wa

(play) .

w;

wg

Preset number

8

repeatedly until “PRESET” appears,

repeatedly to select the

wf

ws

8

/ repeatedly to set the hour,

8

/ repeatedly until the desired

8

To activate or check the timer again

Press CLOCK/TIMER SELECT , press /

repeatedly until “PLAY SEL” appears, and then press

8

ENTER .

To cancel the timer

Repeat the same procedure as above until “TIMER OFF”
appears, and then press ENTER .

To change the setting

Start over from step 1.

Tip

The Play Timer setting remains as long as the setting is not canceled
manually.

ws

8

6

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SET

3-2. CASE

(Page 8)

3-3. BACK PANEL

(Page 8)

3-4. MAIN BOARD

(Page 9)

HCD-HPR90/HPR99XM

SECTION 3

DISASSEMBLY

3-5. AMP BOARD,

POWER BOARD SECTION
(Page 9)

3-6. FRONT PANEL SECTION,

CD MECHANICAL (DLM5B)
(Page 10)

3-7. BELT (DLM3A)

(Page 11)

3-8. OPTICAL PICK-UP BLOCK

(Page 11)

7

HCD-HPR90/HPR99XM

s

Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE

5

case

1

two screws
(case 3 TP2)

3

4

3

2

three screw
(B3)

3-3. BACK PANEL

1

power cord connector
(CN1)

1

two screws
(case 3 TP2)

3

back panel

2

eight screws
(B3)

8

3-4. MAIN BOARD

d

5

two connectors
(CN32, CN604)

9

flexible flat (9 core) cable
(CN1310)

HCD-HPR90/HPR99XM

4

flexible flat (19 core) cable
(CN1302)

q;

flexible flat (15 core) cable
(HPR99XM model)
(CN1301)

5

connector
(HPR99XM model)
(CN1205)

5

qa

connector
(CN1203)

MAIN boar

8

flexible flat (23 core) cable
(CN1309)

1

flexible flat (9 core) cable
(CN1306)

3-5. AMP BOARD, POWER BOARD SECTION

1

screw
(B3)

3

2

flexible flat (11 core) cable
(CN1305)

7

6

two screws (B3)

flexible flat (15 core) cable
(CN1308)

3

AMP board,
POWER board section

2

1

screw
(B3)

9

HCD-HPR90/HPR99XM

s

3-6. FRONT PANEL SECTION, CD MECHANICAL (DLM5B)

4

2

screw
(BVTT3 × 6)

3

four screws
(BVTP3 × 8)

5

chassi

1

three screws
(B3)

q;

front panel section

upper gear

qa

CD mechanical
(DLM5B)

10

8

two claws

B

9

lid (CD)

7

Draw out the tray fully in the
direction of the arrow B.

A

Turn the lower gear in the direction of the arrow A,

6

untill the upper gear gose up to the high position.

3-7. BELT (DLM3A)

)

2

Draw out the tray fully in the
direction of the arrow B.

3

four screws

A

4

plate cam

HCD-HPR90/HPR99XM

5

two belts
(DLM3A)

B

3-8. OPTICAL PICK-UP BLOCK

4

Turn the lower gear in the direction of the arrow A,

1

untill the upper gear gose up to the high position.

5

insulator

3

coil spring (insulator)

8

optical pick-up block

5

3

coil spring (insulator)

2

two screws
(PTPWH M2.6)

3

coil spring (insulator)

insulator

7

CD board

5

insulator

1

6

Remove four solders.

5

insulator

3

coil spring (insulator

2

two screws
(PTPWH M2.6)

flexible flat (16 core) cable
(CN301)

11

HCD-HPR90/HPR99XM

SECTION 4

TEST MODE

COLD RESET

The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customer.

Procedure:

1. Press three buttons of [PLAY MODE/TUNING MODE], [DISPLAY]
and I/1 simultaneously .

2. The fluorescent indicator tube becomes blank momentarily,
then becomes standby states.

COMMON TEST MODE

This mode is used to check operations of Amplifier.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press three buttons of [DSGX], [PLAY MODE/TUNING MODE]
and [DISPLAY] simultaneously.

3. When the COMMON test mode is activated, “SLEEP” and
“c PLAY” blink on the fluorescent indicator tube.

4. Each time [EQ] button on the remote commander is pressed,
the display changes starting “TONE MIN”, “TONE FLAT”
and “TONE MAX” this order.

5. Turn the [VOLUME] knob counterclockwise, “VOL MIN” is
displayed on the fluorescent indicator tube. Turn the [VOLUME]
knob clockwise, “VOL MAX” is displayed on the fluorescent
indicator tube.

6. To release this mode, press the I/1 button.

PANEL TEST MODE

This mode is used to check the fluorescent indicator tube, LED,
model, destination, software version and key.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press three buttons of [PLAY MODE/TUNING MODE], [AUDIO IN]
and [DISPLAY] simultaneously.

3. Fluorescent indicator tube is all turned on and each LED of
[DSGX] and [STANDBY] blink every 0.5 seconds.

4. When you want to enter the model, destination and version display
mode, press the [DISPLAY] button. The model and destination
are displayed alternately on the fluorescent indicator tube.

5. Press the [DISPLAY] button again MC version display on the
fluorescent indicator tube.

6. When [AUDIO IN] button is pressed while the MC version is
displayed, year, month and day of the software creation display .
When [AUDIO IN] button is pressed again, the display returns
to the MC version display.

7. Press the [PUSH ENTER] button, the key check mode is
activated.

8. In the key check mode, the fluorescent indicator tube displays
“K 0 J0 V0”.

9. Each time a button is pressed, “K” value increases. Howe ver,
once a button is pressed, it is no longer taken into account.
All keys are pressed, display becomes “K21”.

10. “V” value increases 1, 2, 3 ... if turn the [VOLUME] knob
clockwise, or it decreases 0, 9, 8 ... if turn the knob
counterclockwise
“J” value increases like 1, 2, 3 ... if turn the jog knob clockwise,
or it decreases like 0, 9, 8 ... if turn the knob counterclockwise.

11. To release this mode, press three keys in the same manner as
step 2, or disconnect the power cord.

CD SHIP MODE

This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press the [CD] or [FUNCTION] key on the remote commander
to select “CD”.

3. Press two buttons of x and [DISC 1] simultaneously.

4. After the “STANDBY” display blinks, “LOCK” is displayed
on the fluorescent indicator tube, and the ship mode is set.

CD SHIP MODE & MEMORY CLEAR

This mode is used to perform CD ship mode and cold reset
simultaneously.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press the [CD] or [FUNCTION] key on the remote commander
to select “CD”.

3. Press three buttons of [DSGX], Z and [DISC 1] simultaneously.

4. After the “STANDBY” display blinks, “LOCK” is displayed
on the fluorescent indicator tube, and the ship mode is set.

ANTITHEFT LOCK MODE

This mode is used to unable to take sample disc out of disc table in
the shop.

Procedure:

1. Press the I/1 button to turn the power on.

2. Insert the CD.

3. Press the CD u button.

4. Press two buttons of x and Z for 5 seconds.

5. The message “LOCKED” is displayed on the fluorescent
indicator tube and the disc slot is locked. (Even if pressing

Z button, the message “LOCKED” is displayed on the

the
fluorescent indicator tube and the disc table is locked)

6. To release from this mode, press two buttons of x and Z for
5 seconds.

7. The message “UNLOCKED” is displayed on the fluorescent
indicator tube and the disc table is unlocked.

CD POWER MANAGE

This mode is used to changed over CD power on/of f for decreasing
of reception noise in the tuner mode.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press the [CD] or [FUNCTION] key on the remote commander
to select “CD”.

3. Press the I/1 button again to turn the power off.

4. Press two buttons of [PUSH ENTER] and I/1 simultaneously.

5. The message “CD POWER” is displayed on the fluorescent
indicator tube momentarily, then display changes “ON” or
“OFF”, and CD power on/off changed ov er in the tuner mode.

12

CD SERVICE MODE

This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the optical pick-up.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press the [CD] or [FUNCTION] key on the remote commander
to select “CD”.

3. Press three buttons of [PUSH ENTER], [DSGX] and [DISC 1]
simultaneously, the message “SERVICE IN” is displayed on
the fluorescent indicator tube.

4. Press the M L button to move the optical pick-up to outside
track and the message “SLED OUT” is displayed on the
fluorescent indicator tube, or press the l m button to
inside track and the message “SLED IN” is displayed on the
fluorescent indicator tube.

5. Press the x button, “LD OFF” is displayed and laser diode is
turned off. Each time x button is pressed, laser diode ON/
OFF switch is performed.

6. To release this mode, press the I/1 button.

TUNER STEP CHANGE-OVER

A step of AM tuning interval can be changed over between 9 kHz
or 10 kHz.

Procedure:

1. Press the I/1 button to turn the power on.

2. Press the [TUNER/BAND] button to select “AM”.

3. Press the I/1 button again to turn the power off.

4. Press two buttons of M L and I/1 simultaneously.

5. The message “STEP 9kHz” or “STEP 10kHz” is displayed on
the fluorescent indicator tube and thus the tuning interval is
changed over.

HCD-HPR90/HPR99XM

13

HCD-HPR90/HPR99XM

e

V

SECTION 5

ELECTRICAL CHECK

CD SECTION

Note:

1. CD Block is basically constructed to operate without adjustment.

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10 MΩ impedance.

4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.

5. Check the focus bias check when optical pick-up block is replaced.

FOCUS BIAS CHECK

oscilloscop

(DC range)

CD board

TP (RFACI)
TP (VC)

+
–

Procedure :

1. Connect oscilloscope to TP (RFACI) and TP (VC) on the CD
board.

2. Press the I/1 button to turn the power on, and press
the Z button to open the CD disc table.

3. Set disc (YEDS-18) on the tray and press the CD u button
to playback.

4. Confirm that oscilloscope waveform is as shown in the f igure
below. (eye pattern)
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.

VOLT/DIV: 200 m
TIME/DIV: 500 ns

level:

0.9

±

0.4 Vp-p

Checking Location:

– CD Board (Conductor Side) –

14

TP

(VC)

IC201

TP

(RFACI)

SECTION 6

DIAGRAMS

6-1. BLOCK DIAGRAM – CD SERVO Section –

3.3V

DETECTOR

(CD)

HCD-HPR90/HPR99XM

A

B

C

D

I-V AMP

E

F

LASER DIODE

PD

LD

OPTICAL PICK-UP

BLOCK

(KSM-213DCP)

M401

(SPINDLE)

M402

(SLED)

2-AXIS
DEVICE

(TRACKING)(FOCUS)

57

A

DECK BLOCK

M

M

CD-L

A

(Page 16)

58 B

59 C

60 D

50 E

51 F

AUTOMATIC

POWER CONTROL

Q321

66 LD

67 PD

16 CH4OUTF

M

15 CH4OUTR

17 CH3OUTF

AC_

64

SUM

FOCUS/TRACKING COIL DRIVE,

SPINDLE/SLED MOTOR DRIVE

IC402

27 OPOUT 38 MDP

24

CH4IN

23

CH3FIN

EG_

65

IN

70RFACO 71 RFACI 3PCMD

CD DSP

IC201

2

OPIN+

41 SFDR

4 PCMDI

5BCK

1LRCK 2 LRCKI

6 BCKI

M

18 CH3OUTR

14 CH1OUTF

13 CH1OUTR

12 CH2OUTF

11 7

CH2OUTR

CH3RIN

CH1FIN

CH1RIN

CH2FIN

CH2RIN

MUTE

20

22

4

5

6

42 SRDR

43 TFDR

44 TRDR

45 FFDR

46 FRDR

(LIMIT)

S201

SSTP

39

3.3V
(CD)

XTAI

108

109

X201

16.9344MHz

XTAO

AOUT1

DATA
CLOK
XLAT
SENS
SCOR

DATA2

CLK2

XLAT-MP3

REQ-MP3

IREQ-MP3

ACK-MP3

XTACN

XRST

112

R-CH

117AOUT2

R-ch is omitted due to same as L-ch.

41
42

39
40

27, 34, 33,

28, 26 – 23

22

CDM +3.3V

SIGNAL PATH

: CD PLAY

LOADING MOTOR

DRIVE

Q1610 – 1613

CAM GEAR MOTOR

DRIVE

Q1614 – 1617

B+ SWITCH

Q1618

CD MECHANISM

M1+
M1+

M2+
M2+

E0, E1/SW2,
E2/SW1,
E3/SW3,
SW5 – SW8

COLLECTOR

ANODE

55FEO

53TEO

52TEI

54FEI

89
11
16
20
26

12
90
13
14
10
15

7
8

35

CD DATA

37

CD CLK

43

CD XLT

36

CD SENS

19

CD SCOR

6

MP3 DATA IN

5

MP3 DATA OUT

7

MP3 CLK

46

MP3 XLAT

45

MP3 REQ

47

MP3 IREQ

44

MP3 ACK

49

CD XTACN

48

CD XRST

50

CD DRIVER MUTE

SYSTEM CONTROLLER

IC1301 (1/4)

DLM5B E0,

E1/SW2,
E2/SW1,
E3/SW3,

SW5 – SW8

DLM5B DISC SENS

M1+
M1–

M2+
M2–

HCD-HPR90/HPR99XM

STANDBY LED

(Page 18)

D

1515

HCD-HPR90/HPR99XM

6-2. BLOCK DIAGRAM – MAIN Section –

CD-L

A

(Page 15)

J981

AUDIO IN

R-CH

(HPR99XM)

J001

XM

3
2

1

D+
D–

VCC

18

COMM_RX_P

19

COMM_RX_N

23

COMM_TX_P

22

COMM_TX_N

5

31

XM RECEIVER

IC001

SC_RX_IN3SC_TX_OUT

ERR_IRQ#

RST#

9

11

32

85

18

21

I2S_LRCLK

I2S_OCLK

CDM_SEL

7

XM

+3.3V

I2S_DA

I2S_CLK

D1205

37

39
41
43

B+ SWITCH

Q001, 003

B+ SWITCH

Q1601, 1602

82

D/A CONVERTER

IC041

3

AOUTL

SDTI

AOUTR R-CH

2

BICK

4

LRCK

1

MCLK

XM
+5.2V

+4V

J982

PHONES

L-CH

HP

(Page 18)

B

(Page 17)

C

INPUT SELECTOR, ELECTRICAL VOLUME,

TUNER/XM

SELECT SWITCH

IC1505

11
10

PDN

5

LINE AMP

IC051

14
15

X1
X2

10A9

Q1503

B

Q1504

X

13

INH

6

Q1505

SURROUND/TONE CONTROL

A1

7

B1

5

C1

9

SEL1

4

VIN1

1

(HPR90)

IC1501

14SI13

SC

OUT1

17

CONTROL SWITCH

Q1501, 1502

MUTING

IC1503

MUTING

R-CH

HEADPHONE

AMP

IC1502

MUTING

IC1504

R-CH

MUTING

CONTROL SWITCH

Q1508, 1509

R-CH

R-ch is omitted due to same as L-ch.

SIGNAL PATH

: TUNER (FM/AM)

: CD PLAY

: XM

: AUDIO IN

83

100

59

65

61

63

60

58

FM 75Ω

COAXIAL

AM

ANTENNA

DO/STEREO

ST DIN

ST CLK

ST CE

FM ANT

L-OUT

R-OUT

AM ANT

TUNER (FM/AM)

56 ST DIN/STEREO
54 ST DOUT
55 ST CLK
53 ST CE

R-CH

XM TXD

XM RXD

RDS INT/XM DTIC IRQ

RDS DATA/XM DTIC RST

XM DTIC CMD

XM POWER 3.3V

XM POWER 5V

AUDIO IN DETECT

SEL A51SEL B

SEL INH

SYSTEM CONTROLLER

IC1301 (2/4)

AMP SI

AMP SC

LINE MUTE

HP MUTE

HCD-HPR90/HPR99XM

1616

6-3. BLOCK DIAGRAM – AMP Section –

HCD-HPR90/HPR99XM

(Page 16)

C

L-CH

X702

49.152MHz

A/D CONVERTER

IC701

LIN

1

15

DOUT

BCK

SCKI

LRCK

CLOCK SHIFT

IC703

CLOCK BUFFER

IC709

SYSTEM CONTROLLER

IC1301 (3/4)

S-MASTER DATA

S-MASTER SHIFT

S-MASTER LATCH

S-MASTER PG MUTE

S-MASTER SOFT MUTE

S-MASTER NSP MUTE

S-MASTER INIT

S-MASTER RST

S-MASTER SD

STREAM PROCESSOR

IC705

12
11
12

70
71
72
66
67
73
75

68
69

DATA

31

BCK

30

LRCK

29

XFSIIN

36

XFSOIN

48

SCDT

21

SCSHIFT

22

SCLATCH

23

PGMUTE

20

SOFTMUTE

19

NSPMUTE

18

INIT

27

OUTL1

OUTL2

OUTR1

OUTR2

11

9

6

4

DIGITAL POWER AMP

IC707

BP

2

AP

17

/RST

4

DIGITAL POWER AMP

IC708

2DP

17 CP

/RST

4

OUT_B
OUT_B
OUT_A
OUT_A

/SD

3

OUT_D
OUT_D
OUT_C
OUT_C

/SD

3

J860

29
30
25
26

29
30
25
26

PROTECT

DETECT

Q701

L.P.F.

L.P.F.

L.P.F.

L.P.F.

OVER LOAD

DETECT

Q702, 703

OVER LOAD

DETECT

Q752, 753

+

–

L

SPEAKER

R

+

–

R-ch is omitted due to same as L-ch.

SIGNAL PATH

: TUNER (FM/AM)

HCD-HPR90/HPR99XM

1717

HCD-HPR90/HPR99XM

6-4. BLOCK DIAGRAM – PANEL, POWER SUPPLY Section –

(HPR99XM)

FL901

FLUORESCENT

INDICATOR

TUBE

HP

B

(Page

16)

(Page

15)

STANDBY LED

D

D952

DSGX

FLUORESCENT INDICATOR

SEG1 – SEG16

GR1 – GR12

31 – 42 14 – 29

1 LED1

S951 – 957,
S961 – 966,
S971 – 975

RV951

PUSH ENTER

(JOG)

RV952

VOLUME

D951

STANDBY

TUBE DRIVER

IC901

DIN
CLK
STB

REMOTE CONTROL

RECEIVER

IC951

ROTARY

ENCODER

ROTARY

ENCODER

LED DRIVE

Q951

SYSTEM CONTROLLER

IC1301 (4/4)

FL SD7 1
FL SCK8 2
FL STB9 3

4 SIRCS

KEY1 – KEY3

93 – 91

74 WAKE UP KEY

95 JOG

94 VOLUME

88 STANDBY LED

XIN

13

15

X1302

5MHz

XOUT

XCIN

10

X1301

32.768kHz

11

XCOUT

84AC DET

38CDM SD

57POWER ON/OFF

12RESET

20AC CUT

PROTECT

DETECT

Q1606

RESET SWITCH

Q1301

XM +5.2V

+12V

+3.3V

(ADC )

+5V

+9V

(HP AMP)

+9V

FLUORESCENT

INDICATOR TUBE

(FL901)

+7V

MOTOR

B+

+4V

+1.8V

(CD)

+3.3V

(CD)

+1.8V

(AMP)

+3.3V

(AMP)

+3.3V

(FL)

CDM

+3.3V

EVER
+3.3V

+3.3V
(LED)

+3.3V REGULATOR

F1
F2

VEE

+1.8V REGULATOR

RESET SIGNAL

GENERATOR

B+ SWITCH

REGULATOR

Q1607 – 1609

+1.8V

REGULATOR

IC203

IC704

IC1302

Q952

D912, 922

IC702

RECT

D1203 (1/2)

D1203 (2/2)

T921

INVERTER

TRANSFORMER

D1206

D1204

D1202

D1201

+5V

REGULATOR

IC1204

RIPPLE
FILTER

Q1510

D1211

OSC

Q921, 922

D1212

+4V

REGULATOR

IC1203

+5V

REGULATOR

IC1206

+12V

REGULATOR

IC1201

+9V

REGULATOR

IC1202

+7V

REGULATOR

IC1205

D1208 – 1210,1213

D652 D33

DC DETECT

Q651, 652

+28V

POWER ON/OFF

RELAY DRIVE

Q650

RECT

D31

RECT

D32

T31

MAIN POWER

TRANSFORMER

ISOLATOR

PH11

ISOLATOR

PH602

SWITCHING

Q12

SWITCHING

Q11

Q601

TRANSFORMER

SHUNT

REGULATOR

IC650

D14

T603

SUB POWER

VG (H)

16

VS

15

VG (L)

12

OCP

9

VC1

8

F/B

2

VENSE

1

POWER CONTROL

D603

ISOLATOR

PH601

VD

IC11

POWER CONTROL

IC601

DRAIN

5

VCC

4

FB

2

18

(AC IN)

F1

+

+

VOLTAGE

SELECTOR

120 – 127V

220 – 240V

(HPR90: E, E51)

RECT

D1

S1

LINE FILTER

T1

Abbrivation

: Chilean and Peruvian modelsE51

HCD-HPR90/HPR99XM

1818

• Circuit Boards Location• Note For Printed Wiring Boards and Schematic Diagrams

d

• Circuit Boards Location

HCD-HPR90/HPR99XM

Ver. 1.1

Note on Printed Wiring Board:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

• f : internal component.

• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.

• Indication of transistor

C

Q

B

E

B

These are omitted.

Q

CE

These are omitted.

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in Ω and 1/
specified.

• f : internal component.

• 2 : nonflammable resistor.

• C : panel designation.

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.

• A : B+ Line.

• B : B– Line.

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
– CD Board –
no mark :CD PLAY
– XM Board –
no mark : XM
– Other Boards –
no mark : TUNER (FM/AM)
(): CD PLAY

〈〈 〉〉 : XM

∗ : Impossible to measure

• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc­tion tolerances.

• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc­tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F : TUNER (FM/AM)
J : CD PLAY

: XM

f : AUDIO IN

• Abbreviation
AR : Argentina model
AUS: Australian model
CND : Canadian model
E51 : Chilean and Peruvian models
MX : Mexican model
SP : Singapore model

4

W or less unless otherwise

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

FL board

PANEL board

POWER board

TUNER

AMP board

MAIN board

SP board

XM REG boar
(HPR99XM)

XM board
(HPR99XM)

CD board

HP A-IN board

HCD-HPR90/HPR99XM

1919

HCD-HPR90/HPR99XM

6-5. PRINTED WIRING BOARD – CD Board –

1 2 3 4 567 8 9 10

A

CD BOARD

(COMPONENT SIDE)

C401

B

C406

C

D

E

F

R401

C201

R201

C202

R202

R207

C101

C102

C108

C110

C424

C227

4

5

IC203

R423

C203

C226

3

1

• See page 19 for Circuit Boards Location.

X201

C204

R421

C277

C276

C268

R271

C275

C266

C267

C272

R276

C219

C215

R203

C223

R260

C271

C220

C210

C321

C104

C105

C232

C206

C257

R256

C274

Q321

C107

E

C109

R323

C322

C205

R322

R321

: Uses unleaded solder.

C207

C323

R324

1-868-067-

12

(12)

CD BOARD

(CONDUCTOR SIDE)

C224

TP

(VC)

C251

C253

R252

R253

R255

R254

C256

C252

C254

R102

R101

31

60

M401

(SPINDLE)

R452

R451

R104

R107

R109

R108

30

IC201

61

C208

C258

C230

OPTICAL PICK-UP BLOCK

TP

(RFACI)

CN301

(KSM-213DCP)

R257

C103

C451

R110

C260

R105

R103

R250

M

C264

R278

C261

R258

R265

C221

R268

C273

S201

(LIMIT)

28 22

R280

C405

21 15

C403

IC402

17 14

R277

R275

1

120

91

90

C265

R266

C217

C303

R267

C218

C214

C213

C222

C304

R292

C301

C291

R291

R270

C292

C112

C113

C111

8

C404

R112

R113

R111

1-868-067-

M

M402

(SLED)

CN102

A

12

(12)

MAIN
BOARD
CN1309

(Page 22)

HCD-HPR90/HPR99XM

2020

HCD-HPR90/HPR99XM

6-6. SCHEMATIC DIAGRAM – CD Board –

C275

5p

100

R113

100

R112

R111

100

CN102

23P

R201

0

22p

22p

220p

220p

220p

C113

C112

C111

C110

C108

(Page

25)

CD DATA

MP3 CLK

D-MUTE

D+3.3V

D-OUT

D-GND

L-CH

A-GND

R-CH

A+3.3V

XATCN

CD XRST

MP3 IREQ

CD CLK

MP3 DATA

MP3 XLAT

MP3 REQ

MP3 ACK

CD XLAT

CD SENS

CD SCOR

M-GND

M+7V

• See page 36 for Waveforms. • See page 37 for IC Block Diagrams. • See page 44 for IC Pin Function Description.

C210

0.1

C208

R256

C257

C274

0.1

22k

0.1

0.1

R321

C323

R324

100

100k

C256

0.1

LD

PD

C2PO

GFS

D

EG_IN

AVDD4

RFDCO

C

PDSENS

AC_SUM

B

A

VC

FEO

FEI

TEO

TEI

F

E

AVSS0

AVDD0

IOVDD1

FRDR

FFDR

TRDR

TFDR

SRDR

SFDR

IOVSS1

SSTP

MDP

LOCK

VSS

VDD

VSS

FOK

DFCT

MIRR

SVDD

SVSS

COUT

SCOR

VDD

0.1

C206

C224

0.1

10V

(VC)

R255

1k

R253

1k

2.2

C322

1

R322

2.2

R323

0

C321

1000p

TP

100 10V

C207

4700p

C254

R254

10k

470p

C253

4700p

C252

R252

10k

470p

C251

C205

0.1

C404

0.1

C405

0.1

C268 C215
10p 0.1

R203

22p

22p

C102

C101

+1.8V REGULATOR

BH18LB1WG-TR

R202

0

R110

R103

R105

R104

R109

R108

R107

R102

R101

100

100

100

100

100

100

100

100

100

IC203

C218

0.1

C201

100
10V

R207 C226

01

22p

22p

C103

C105

16.9344MHz

220p

C104

TP

VCTL

REQ-MP3

(RFACI)

0.01

0.47

C230
100p

C261

C260

1M

R250

220k

220p

R257
100k

R258

C258

ASYI

ASYO

VPCO

CD DSP

IC201

ACK-MP3

VDD

XLAT

C272

0.1

RFC

BIAS

RFACI

AVSS4

RFACO

AVDD3

SVDD

SVSS

XPCK

XUGF

WFCK

SENS

R280

0

0

1000p

470p

R260

C264

C273

0.1

4.7k

C265

R265

R266

1k

10k

R267

4.7k

C221

0.1

CLK2

VSS

VDD

DATA

TEST1

SSTB-MP3

LRCKI

LRCK

BCKI

PCMDI

PCMD

BCK

IOVSS0

R275

100

SVSS

SVDD

JTAGTCK

JTAGTDI

JTAGTDO

JTAGTMS

TRST

VSS

VDD

IOVDD2

DOUT

TEST

TES1

IOVSS2

PLLVDD

PLLVSS

XVSS

XTAO

XTAI

XVDD

AVDD1

AOUT1

VREFL

AVSS1

AVSS2

VREFR

AOUT2

AVDD2

IOVDD0

R276 C271

47k 0.1

100

R277

0.1

C222

0.1

C213

C214

0.1

C223

0.1

C266C267

10p5p

R270

X201

C202

0.1

C217

0.1

VIN

STBY

GND

C203

C204

100

0.1

10V

220p

220p

R401

0

C109

C107

1k

R271

1M

1

C276

R291
100

C291
470p

1

C277

C292
470p

R292

100

C219

NC

C227

1

C401

220
10V

0.1

VOUT

C220

0.1

R268

FILI

PCO

FILO

SVSS

CLTV

SVDD

XTACN

100

R278

AVSS3

CXD3014A-201R

CLOK

IREQ-MP3

XLAT-MP3

DATA2

VSS

XRST

C232

0.1

FOCUS/TRUCKING

COIL DRIVE,

SPINDLE/SLED

MOTOR DRIVE

BA5947FM

IC402

2SA2119K

AUTOMATIC

POWER

CONTROL

CN301

C301

0.1

C303

C304

10

1

Q321

R452 C451
10k 0.047

R451

22k

C424

0.1

R423

SP-

CH1PUTF

CH4OUTR

+

SP

CH1OUTR

CH4OUTF

10k

GND

CNF4

POWVCC

CH2OUTF

CH2OUTR

MUTE

POWVCC

CH3OUTR

GND

CH3OUTF

L+
S

SL-

CH2RIN

CH3RIN

CH2FIN

CH3FIN

CH1RIN

CH4IN

CH1FIN

CH4CAPA

GAIN-SW

VREF

R421

0

OPIN-

OPIN+

PREVCC

OPOUT

C406

0.1

16P

VC

VCC

E

D

A

B

C

F

GND

LD

VR

PD

F+

T+

T-

F-

SP+

SP-

SL+

SL-

S201

(LIMIT)

(SPINDLE)

M401

M402

(SLED)

HCD-HPR90/HPR99XM

2121