Sony HCD-FZ900KW, HCD-FZ900M Service Manual

HCD-FZ900KW/FZ900M

SERVICE MANUAL

Ver. 1.0 2009.04

Photo: HCD-FZ900KW

• HCD-FZ900KW/FZ900M are the ampliﬁ er, DVD/CD and tuner section in DAV-FZ900KW/FZ900M.

This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround decoder and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of

Dolby Laboratories. ** Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other

U.S. and worldwide patents issued & pending. DTS and DTS

Digital Surround are registered trademarks and the DTS logos and

Rights Reserved.

Model Name Using Similar Mechanism

Mechanism Type CDM85-DVBU102

Optical Pick-up Name KHM-313CAA

E Model

Australian Model

HCD-FZ900KW

Russian Model

HCD-FZ900M

HCD-DZ290K/DZ295K/DZ390K/ DZ590K/DZ690K/DZ790K

Ampliﬁ er Section

FZ900KW: Chinese models: Surround mode (reference) RMS output power FL/FR/C*: 100 watts (per channel at 3 ohms, 1 kHz) Subwoofer*: 100 watts (at 3 ohms, 80 Hz) FZ900KW: Latin American models: Stereo mode (rated) 108 W + 108 W (at 3 ohms, 1 kHz, 1% THD) Surround mode (reference) RMS output power FL/FR*: 144 watts (per channel at 3 ohms, 1 kHz, 10% THD) C*: 142 watts (per channel at 3 ohms, 1 kHz, 10% THD) Subwoofer*: 280 watts (at

1.5 ohms, 80 Hz, 10% THD) FZ900KW: Other models: Stereo mode (rated) 108 W + 108 W (at 3 ohms, 1 kHz, 1% THD) Surround mode (reference) RMS output power FL/FR/C*: 144 watts (per channel at 3 ohms, 1 kHz, 10% THD) Subwoofer*: 280 watts (at

1.5 ohms, 80 Hz, 10% THD)

SPECIFICATIONS

FZ900M: Stereo mode (rated) 108 W + 108 W (at 3 ohms, 1 kHz, 1% THD) Surround mode (reference) RMS output power FL/FR/C/SL/SR*: 144 watts (per channel at 3 ohms, 1 kHz, 10% THD) Subwoofer*: 280 watts (at

1.5 ohms, 80 Hz, 10% THD)

* Depending on the decoding mode settings and the source, there may be no sound output.

Inputs (Analog) TV (AUDIO IN) Sensitivity: 450/250 mV SAT/CABLE (AUDIO IN) Sensitivity: 450/250 mV FZ900KW: AUDIO IN/MIC Sensitivity: AUDIO IN 250/125 mV/MIC 1 mV FZ900M: AUDIO IN/MIC1 Sensitivity: AUDIO IN 250/125 mV/MIC1 1 mV MIC2 Sensitivity: 1 mV Inputs (Digital) TV (COAXIAL IN/OPTICAL IN) Impedance: 75 ohms/ Input Stream: Dolby Digital 5.1ch/DTS 5.1ch/ Linear PCM 2ch (Sampling Frequency: less than 48 kHz)

FZ900KW: Outputs (Analog) Phones Accepts low- and high impedance headphones.

Super Audio CD/DVD System

Laser Diode Properties Emission Duration: Continuous Laser Output: Less than

44.6μW

* This output is the value measurement at a distance of 200mm from the objective lens surface on the Optical Pick-up Block with 7mm aperture.

Signal format system FZ900KW: Mexican and Latin American models: NTSC Australian models: PAL/NTSC Other models: NTSC/PAL FZ900M: PAL/NTSC

– Continued on next page –

DVD RECEIVER

9-889-478-01

2009D04-1

2009.04

©

Sony Corporation

Audio&Video Business Group Published by Sony Techno Create Corporation

HCD-FZ900KW/FZ900M

USB Section

(USB) port:

Maximum current: 500 mA

Tuner Section

System PLL quartz-locked digital synthesizer FM Tuner section Tuning range North American models: 87.5 MHz - 108.0 MHz (100 kHz step) Other models: 87.5 MHz - 108.0 MHz (50 kHz step) Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz

Video Section

Outputs VIDEO: 1 Vp-p 75 ohms COMPONENT: Y: 1 Vp-p 75 ohms PB/CB, PR/CR: 0.7 Vp-p 75 ohms HDMI OUT: Type A (19 pin)

General

Power requirements North American models: 120 V AC, 60 Hz Latin American models: 110 V - 240 V AC, 50/60 Hz Other models: 220 V - 240 V AC, 50/60 Hz Power consumption FZ900KW: On:125 W Standby: 0.3 W (at the Power Saving mode) FZ900M: On: 160 W Standby: 0.3 W (at the Power Saving mode) Output voltage (DIGITAL MEDIA PORT) DC 5 V Output current (DIGITAL MEDIA PORT) 700 mA Dimensions (approx.) FZ900KW: 430 mm × 66 mm × 395 mm (w/h/d) incl. projecting parts 430 mm × 66 mm × 425 mm (w/h/d) (incl. Wireless transceiver) FZ900M: 430 mm × 66 mm × 390 mm (w/h/d) incl. projecting parts Mass (approx.) 4.3 kg

Supported ﬁ le format MP3 (MPEG 1 Audio Layer-3)

File Extension: mp3 Bitrate: 32 kbps - 320 kbps Sampling frequencies: 32/44.1/48 kHz

WMA (USB device only)

File Extension: wma Bitrate: 48 kbps - 192 kbps Sampling frequencies: 44.1 kHz

AAC (USB device only)

File Extension: m4a Bitrate: 48 kbps - 320 kbps Sampling frequencies: 44.1 kHz

DivX

File Extension: avi/divx Video codec: DivX video Bitrate: 8 Mbps (MAX) Frame rate: 30 fps Resolution: 720 × 576 Audio codec: MP3

MPEG4

File format: MP4 File Format File Extension: mp4/m4v Video codec: MPEG4 Simple Proﬁ le (AVC is not compatible.) Bitrate: 4 Mbps Frame rate: 30 fps Resolution: 720 × 576 Audio codec: AAC-LC (HE-AAC is not compatible.) DRM: Not compatible

Design and speciﬁ cations are subject to change without notice.

SPECIAL COMPONENT NOTICE

The components identiﬁ ed by mark 9 contain conﬁ dential infor- mation. Strictly follow the instructions whenever the components are repaired and/or replaced.

SAFETY-RELATED COMPONET WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

2

HCD-FZ900KW/FZ900M

MODEL IDENTIFICATION – Back Panel –

Model Part No.

FZ900M: RU model

FZ900KW: E3 model

FZ900KW: E15 model

FZ900KW: EA model

FZ900KW: SP model

FZ900KW: TH model

FZ900KW: E32 model

FZ900KW: AUS model

FZ900KW: E12 model

• Abbreviation AUS : Australian model E3 : 240V AC area in E model E12 : 220 – 240V AC area in E model E15 : Iran model E32 : 110 – 240V AC area in E model EA : Saudi Arabia model RU : Russian model SP : Singapore model TH : Thai model

Parts No.

4-122-167-2[]

4-122-167-3[]

4-122-167-4[]

4-122-167-5[]

4-122-167-6[]

4-122-167-8[]

4-122-168-2[]

4-122-168-5[]

4-122-168-6[]

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

This appliance is classiﬁ ed as a CLASS 1 LASER product. This marking is located on the rear or bottom exterior.

CAUTION

Use of controls or adjustments or performance of procedures other than those speciﬁ ed herein may result in hazardous radia- tion exposure.

NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be damaged by heat.

FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of soldering iron around 270 °C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C. Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to ﬂ ow)

than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

3

HCD-FZ900KW/FZ900M

SERVICING NOTES

HCD-FZ900KW/FZ900M

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The ﬂ exible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reﬂ ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH

1. Open the case and turn POWER on with no disc inserted.

2. Conﬁ rm that the following operation is performed while observing the objecting lens from the clearance of DVD mechanism deck.

1) Conﬁ rm that laser beam is spread.

2) Up and down motion of the objective lens. (2 times)

DISC TRAY LOCK

The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.

Setting Procedure :

1. Press the [

2. Press the [FUNCTION] button to set DVD function.

3. Insert a disc.

4. Press the [x] button and the [Z] button simultaneously for ﬁ ve seconds.

5. The message “LOCKED” is displayed and the tray is locked.

Releasing Procedure :

1. Press the [x] button and the [Z] button simultaneously for ﬁ ve seconds again.

2. The message “UNLOCKED” is displayed and the tray is unlocked.

Note: When “LOCKED” is displayed, the tray lock is not released by

turning power on/off with the [

On cleaning discs, disc/lens cleaners

• Do not use cleaning discs or disc/lens cleaners (including wet or spray types). These may cause the apparatus to malfunction.

IMPORTANT NOTICE

Caution: This system is capable of holding a still video image or on-screen display image on your television screen indeﬁ nitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Projection televisions are especially susceptible to this.

] button to turn the set on.

?/1

] button.

How to open the disc table when power switch turns off

Insert a tapering driver into the aperture of the unit bottom, and slide it in the direction of the arrow.

Peel off the lavel and so the lever is moved in the direction of the arrow with the thin rod.

lavel

tray

Precaution when installing a new OP unit/ Precaution before unsoldering the static electricity prevention solder bridge

When installing a new OP unit, be sure to connect the ﬂ exible printed circuit board ﬁ rst of all before removing the static electricity prevention solder bridge by unsoldering. Remove the static electricity prevention solder bridge by unsoldering after the ﬂ exible printed circuit board has already been connected. (Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)

Attention when transported

Use this mode when returning the set to the customer after repair.

Procedure:

1. Press the [

2. Press the [FUNCTION] button to set the function “DVD”.

3. Remove all discs, and then press two buttons [N] and [ simultaneously.

4. After a message “MECHA LOCK” is displayed on the ﬂ uorescent indicator tube, pull out the AC plug.

5. To exit from this mode, press the [ on.

] button to turn the set on.

?/1

] button to turn the set

?/1

]

5

HCD-FZ900KW/FZ900M

Discharge the charged electricity in capacitors to prevent electric shock as follows

When disassembling the machine, be sure to discharge the charged electricity in the following capacitors. Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.

POWER board C903: 390V C932, C933, C934, CN904: 30V

Point of capacitor discharge for C932, C933, C934: Connect to the red and black wire of CN904.

800Ω/2W

Point of capacitor discharge for C903: Connect to the foot of C903.

6

DISASSEMBLY

• This set can be disassembled in the order shown below.

SET

2-1. CASE (Page 8)

2-2. FRONT PANEL SECTION (Page 8)

HCD-FZ900KW/FZ900M

SECTION 2

2-3. BACK PANEL SECTION (FZ900KW) (Page 9)

2-5. DVD MECHANISM DECK (Page 10)

2-6. POWER BOARD, USB BOARD (Page 10)

2-7. MAIN BOARD, SPEAKER BOARD, DSP BOARD (Page 11)

2-8. IO-COMPONENT BOARD (Page 11)

2-4. BACK PANEL SECTION (FZ900M) (Page 9)

2-9. TRAY (Page 12)

2-10. BELT (Page 12)

2-11. MS-203 BOARD (Page 13)

2-12. BASE UNIT (Page 13)

2-13. OPTICAL PICK-UP (Page 14)

7

HCD-FZ900KW/FZ900M

Note: Follow the disassembly procedure in the numerical order given.

2-1. CASE

 case

 two screws

(case 3 TP2)

 five screws (BV/ring)

 two screws (case 3 TP2)

2-2. FRONT PANEL SECTION

 claw

 loading panel

 front panel section

 CN4014 (4P) (FZ900KW)

CN4013 (5P) (FZ900M)

 claw

 four screws

(+BV3 (3-CR))

 wire (flat type)(19 core) (CN507)

 CN3001 (3P) (FZ900KW)

 label





tray

8

2-3. BACK PANEL SECTION (FZ900KW)

RG back panel section

 wire (flat type) (9 core)

(CN4016)

 screw (+BV3 (3-CR))

 CN801 (4P)

HCD-FZ900KW/FZ900M

 three screws (+BVTP 3 × 8)

 two screws (+BVTP 3 × 8)

 screw (+BVTP 3 × 8)

RB screw (+B 3 × 6)

RT two screws (+BVTP 3 × 8)

 CN908 (2P)

2-4. BACK PANEL SECTION (FZ900M)

RE back panel section

 wire (flat type) (13 core)

(CN306)

 two screws (+BVTP 3 × 8)

 three screws (+BVTP 3 × 8)

RE screw (+BVTP 3 × 8)

 CN3000 (2P)

 CN901 (2P)

 screw

(+BVTP 3 × 8)

 wire (flat type) (11 core) (CN4017)

 CN101 (4P)

 screw

(+B 3 × 6)

RB two screws (+BVTP 3 × 8)

RT screw (+BVTP 3 × 8)

 CN3000 (2P)

 CN901 (2P)

 wire (flat type) (13 core)

(CN306)

 CN102 (2P)

9

HCD-FZ900KW/FZ900M

2-5. DVD MECHANISM DECK

 screw (+BV3 (3-CR))

 cover (CDM-DSY)

 two screws

(+BV3 (3-CR))

 DVD mechanism deck

 screw

(+BV3 (3-CR))

 screw (+BV3 (3-CR))

 screw (+BV3 (3-CR))

 wire (flat type)(5 core) (CN1202)

 CN1201 (6P)

 wire (flat type)(24 core)

(CN1101)

2-6. POWER BOARD, USB BOARD

 CN906 (13P)

RE three screws

(+PWH 3 × 8)

RI POWER board

 two screws

(+BV3 (3-CR))

RG three screws (+PWH 3 × 8)

 CN904 (4P)

RB screw

(+BV3 (3-CR))

RT cover (rear)

 screw

(+BV3 (3-CR))

 cover (front)

 two screws

(+BVTP 3 × 8)

 plate (POW) insulated

 bracket (POW-DSY)

(Except: E32)

10

 CN5201 (5P)

RH holder PC board

 USB board

2-7. MAIN BOARD, SPEAKER BOARD, DSP BOARD

RB three screws

 wire (flat type) (17 core) (CN472)

 wire (flat type) (7 core) (CN302)

 wire (flat type) (17 core) (CN503)

(FZ900KW) wire (flat type) (19 core) (CN504) (FZ900M)

RG six screws

 screw

(+BV3 (3-CR))

 screw (+BV3 (3-CR))

(+BV3 (3-CR))

lug

(+BV3 (3-CR))

HCD-FZ900KW/FZ900M

RT heat sink section

 two screws

(+BV3 (3-CR))

RE three radiation sheet

RE two radiation sheet

(FZ900M)

RE two radiation sheet

 SPEAKER board

 CN700 (3P)

 DSP board

2-8. IO-COMPONENT BOARD

 two screws (+BV3 (3-CR))

 CN5300 (4P) (FZ900KW) CN5301(4P) (FZ900M)

RH MAIN board

 SCORE board

 IO-COMPONENT board

11

HCD-FZ900KW/FZ900M

2-9. TRAY

 Move the chuck cam in the direction of the arrow.



bottom side

 two claws

2-10. BELT



chuck cam





 tray

belt

12

 two claws

2-11. MS-203 BOARD



MS-203 board



DC motor

 three claws

HCD-FZ900KW/FZ900M

 screw (M 1.7 × 2.5)

2-12. BASE UNIT



chuck cam

 two claws

 two claws

 base unit

13

HCD-FZ900KW/FZ900M

2-13. OPTICAL PICK-UP

 two insulator screws

 FFC holder

 two insulator screws

 two insulators

 two insulators

 optical pick-up

(KHM-313CAA)

 two claws

14

SECTION 3

TEST MODE

HCD-FZ900KW/FZ900M

Note: Incorrect operations may be performed if the test mode is not

entered properly.

In this case, press the [?/1] button to turn the power off, and

retry to enter the test mode.

1. Cold Reset

• The cold reset clears all data including preset data stored

in the RAM to initial conditions. Execute this mode when returning the set to the customers.

Procedure:

1. Press the [

2. Press three buttons [

] button to turn the power on.

?/1

], [N] and [

x

] simultaneously.

?/1

3. When this button is operated, display as “COLD RESET” for a while and all of the settings are reset.

2. Panel Test Mode

• This mode is used to check the software version, FL and

KEY.

2-1. Display Test Mode Procedure:

1. Press the [

2. Press three buttons [

] button to turn the power on.

?/1

], [.] and [FUNCTION] simultane-

x

ously.

3. When the display test mode is activated, all segments are turned on. When the mode in, lamps of “MOVIE”, “MUSIC” and “REC TO USB” are turn off.

4. To exit from this mode, press three buttons [x], [.] and [FUNCTION] simultaneously.

2-2. Version Test Mode Procedure:

1. When the display test mode is activated, press the [.] button and the message “DSY9GKW” (FZ900KW), “DSY9GKD” (FZ900M) are displayed, the version test mode is activated.

2. Whenever the [.] button is pressed, the display changes in the following order.

“DSY9GKW” (Model name) U“AS1A2*1” (Destination) U

UMC Version U SYS Version UUI Version U UDVD Version UST Version U TA Version U UDSP Version UTM Version UMM Version U

U CLA Version UCEC Version USAIR Version

*1: AS1A2 changes depending on destination.

3. Press the [>] button and the date of the software production is displayed.

4. Press the [>] button again and the version is displayed.

5. To exit from this mode, press three buttons [x], [.] and [FUNCTION] simultaneously.

2-4. Key Test Mode Procedure:

1. When the display test mode is activated, press the [N] button, to select the key test mode.

2. To enter the KEY test mode, the ﬂ uorescent indicator displays “K0 V0”. Each time an another button is pressed, “KEY” value increases. However, once a button is pressed, it is no longer taken into account. When all keys are pressed correctly, “K9 V0” is displayed.

3. When the [VOLUME] control is turned in the direction of (+), “V0” is changed to “V1”, then ... “V9”.

When the [VOLUME] control is turned in the direction of (–),

“V0” is changed to “V9”, then ... “V1”.

4. To exit from this mode, press three buttons [

], [.] and

x

[FUNCTION] simultaneously.

3. Disc Tray Lock

• The disc tray lock function for the antitheft of an demonstra-

tion disc in the store is equipped.

Setting Procedure :

1. Press the [

] button to turn the set on.

?/1

2. Press the [FUNCTION] button to set DVD function.

3. Insert a disc.

4. Press the [x] button and the [Z] button simultaneously for ﬁ ve seconds.

5. The message “LOCKED” is displayed and the tray is locked.

Releasing Procedure :

1. Press the [x] button and the [Z] button simultaneously for ﬁ ve seconds again.

2. The message “UNLOCKED” is displayed and the tray is unlocked.

Note: When “LOCKED” is displayed, the tray lock is not released by

turning power on/off with the [?/1] button.

4. DVD Ship Mode

• Use this mode when returning the set to the customer after

repair.

Procedure:

1. Press the [

] button to turn the set on.

?/1

2. Press the [FUNCTION] button to set the function “DVD”.

3. Remove all discs, and then press two buttons [N] and [

?/1

simultaneously.

4. After a message “MECHA LOCK” h “UNPLUG” is displayed on the ﬂ uorescent indicator tube, pull out the AC plug.

5. To exit from this mode, press the [

] button to turn the set

?/1

on.

]

2-3. FL Pattern Test Mode Procedure:

1. When the display test mode is activated, press the [x] button, to select the FL pattern test mode. When the FL pattern test mode, half segments of FL display and lamps of “MOVIE”, “REC TO USB” are turn on.

2. Press the [x] button, half segments of FL display and lamp of “MUSIC” and “

, VOLUME Illumination” are turn on.

"/1

3. Next press the [x] button, all segments of FL display is turn on.

4. To exit from this mode, press three buttons [x], [.] and [FUNCTION] simultaneously.

15

HCD-FZ900KW/FZ900M

5. Product Out

• This mode moves the optical pick-up to the position durable to vibration and clears all data including preset data stored in the RAM to initial conditions. Use this mode when returning the set to the customer after repair.

Procedure:

1. Press the [

] button to turn the power on.

?/1

2. Press the [FUNCTION] button to set the function “DVD”.

3. Remove all discs, and then press three buttons [x], [Z] and [VOLUME+] simultaneously.

4. Displayed to message “SERVICE IN” on the fluorescent indicator tube when pressing in turn the [4] t [DVD MENU] t [CLEAR] buttons on the remote commander.

5. After the “STANDBY” blinking display ﬁ nishes, the message “MECHA LOCK” h “UNPLUG” is displayed on the ﬂ uorescent indicator tube disconnect the AC power plug, then the product out mode is set.

6. Color System Change (Except RU, E32 models)

• Color system change to video signal format (NTSC/PAL).

Procedure:

1. Press the [

] button to turn the set on.

?/1

2. Press the [FUNCTION] button to set the function “DVD”.

3. Press the [

4. Press two buttons [.] and [

] button to turn the set OFF.

?/1

] simultaneously, and the display of ﬂ uorescent indicator tube changes to “COLOR PAL” or “COLOR NTSC”.

DVD SECTION

7-1. GENERAL DESCRIPTION

• The IOP measurement allows you to make diagnosis and adjustment simply by using the remote commander and monitor TV. The instructions, diagnosis results, etc. are given on the on-screen display (OSD).

Be sure to execute the IOP measurement when a BU (Base

Unit) is replaced.

7-2. HOW TO ENTER TEST MODE

While pressing the [ [VOLUME] control in the direction of (+) with the DVD player in power on. The Test Mode starts, displayed “SERVICE IN” on this model display then the menu shown below will be displayed on the TV screen. * The display of the “Model Name” of the “Remocon Diagnosis

Menu” change with the model and the destination. Refer to

below on the model name. FZ900KW : DSY9GKW FZ900M : DSY9GKD

0. External Chip Check

1. Servo Parameter Check

2. Drive Manual Operation

3. Emergency History

4. Version Information

] and [Z] buttons simultaneously, turn

x

Remocon Diagnosis Menu

1

Model Name IF-con : Ver. XX.XX (XXXX) Syscon : Ver. X.XXX

*1: Changes depending on destination

: DSY9GKW_XX

*

The menu above is the Remocon Diagnosis Menu screen which consists of ﬁ ve main functions. At the bottom of the menu screen, the model name and IF-con version. To exit from the Test Mode, press the [

] button on the remote commander.

?/1

7-3. EXECUTING IOP MEASUREMENT

In order to execute IOP measurement, the following standard procedures must be followed.

(1) In power on, while pressing the [x] and [Z] buttons simultane-

ously, turn the [VOLUME] control in the direction of (+).

Remocon Diagnosis Menu

0. External Chip Check

1. Servo Parameter Check

2. Drive Manual Operation

3. Emergency History

4. Version Information

1

Model Name IF-con : Ver. XX.XX (XXXX) Syscon

*1: Changes depending on destination

: DSY9GKW_XX

: Ver. X.XXX

*

16

HCD-FZ900KW/FZ900M

(2) Select “2. Drive Manual Operation” by pressing the [2] button

on the remote commander. The screen will appear as shown.

Drive Manual Operation

1. Servo Control

2. Track/Layer Jump

3. Manual Adjustment

4. Tray Aging Mode

5. MIRR time adjust

0. Return to Top Menu

(3) Select “3. Manual Adjustment” by pressing the [3] button on

the remote commander. The screen will appear as shown.

Manual Adjust

1. Track Balance Adjust:

2. Track Gain Adjust:

3. Focus Balance Adjust:

4. Focus Gain Adjust:

5. Eq Boost Adjust:

6. Iop:

7. TRV. Level:

8. S curve(FE) Level:

9. RFL(PI) Level:

0. MIRR Time:

Oo Change Value

[RETURN] Return to previous menu

(4) Select “6. IOP” by pressing the [6] button on the remote

commander.

7-4. EMERGENCY HISTORY

To check the emergency history, please follow the following procedure.

(1) From the Top Menu of Remocon Diagnosis Menu, select “3.

Emergency History Check” by pressing the [3] button on the remote commander. The following screen appears on the onscreen display.

Emg. History Check

Laser Hours CD 999h 59min

01. 01 05 04 04 00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page [O] Return to Top Menu

DVD 999h 59min

00 92 46 00

(2) You can check the total time when the laser is turned on during

playback of DVD and CD from the above menu. The maximum time, which can be displayed are 999h 59min.

(3) You can check the error code of latest 10 emergency history

from the above menu. To view the previous or next page of emergency history, press [.] or [>] button on the remote commander. The error code consists of the following three blocks. The ﬁ rst block indicates the error code. The second block indicates the parameter and the third block indicates the time of error code as shown below.

• Error Code

(5) Wait until a hexadecimal number appear.

Manual Adjust

1. Track Balance Adjust:

2. Track Gain Adjust:

3. Focus Balance Adjust:

4. Focus Gain Adjust:

5. Eq Boost Adjust:

6. Iop. 4E:

7. TRV. Level:

8. S curve(FE) Level:

9. RFL(PI) Level:

0. MIRR Time:

Oo Change Value

[RETURN] Return to previous menu

(6) Convert each data from hexadecimal to decimal using

conversion table.

(7) Please ﬁ nd the label on the rear of the BU (Base Unit). The default IOP value is written in the label.

(8) Subtract between these two values.

(9) If the remainder is smaller than 93 (decimal), then it is OK.

However if the value is higher than 93, then the BU is defective and need to be change.

(10) Press the [RETURN] button on the remote commander to

return back to previous menu.

(11) Press the [0] button on the remote commander to return to Top

Menu.

Emg. History Check

Laser Hours CD 999h 59min

*1 *2

01. 01 05 04 04 00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page [O] Return to Top Menu

DVD 999h 59min

00 92 46 00

*3

*1 : Error Code *2 : Parameter of error code *3 : Time of error code

The meaning of error code is as below:

01: Communication error (No reply from syscon) 02: Syscon hung up 03: Power OFF request when syscon hung up 19: Thermal shutdown 24: MoveSledHome error 25: Mechanical move error (5 Changer) 26: Mechanical move stack error 30: DC motor adjustment error 31: DPD offset adjustment error 32: TE balance adjustment error 33: TE sensor adjustment error 34: TE loop gain adjustment error 35: FE loop gain adjustment error 36: Bad jitter after adjustment 40: Focus NG 42: Focus layer jump NG 52: Open kick spindle error 51: Spindle stop error

17

HCD-FZ900KW/FZ900M

60: Focus on error 61: Seek fail error 62: Read Q data/ID error 70: Lead in data read fail 71: TOC read time out (CD) 80: Can’t buffering 81: Unknown media type

7-4-1. Clear the Laser Hour

Press [

DISPLAY] button and then press [CLEAR] button on the remote commander. The data for both CD and DVD data are reset.

Emg. History Check

Laser Hours CD 0h 0min

01. 01 05 04 04 00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page [O] Return to Top Menu

DVD 0h 0min

00 92 46 00

7-4-2. Clear the Emergency History

Press [DVD TOP MENU] button and then press [CLEAR] button on the remote commander. The error code for all emergency history would be reset.

Emg. History Check

Laser Hours CD 999h 59min

01. 00 00 00 00 00 00 00 00 00 00 00 00

02. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

[Next] Next Page [Prev] Prev Page [O] Return to Top Menu

DVD 999h 59min

00 00 00 00

7-4-4. Return to the Top Menu of Remocon Diagnosis

Menu

Press [0] button on the remote commander.

7-5. CHECK VERSION INFORMATION

To check the version information, please follow the following procedure.

(1) From the Top Menu of Remocon Diagnosis Menu, select “4.

Version Information” by pressing the [4] button on the remote commander. The following screen appears on the on-screen display.

Version information

Firm (Main) : Ver. xxxxx Firm (Sub) : xxxxx RISC : xxxxx 8032 : xxxxx Audio DSP : xxxxx Servo DSP : xxxxx

Phy,Adr, : F.F.F.F

[O] Return to Top Menu

To return to the Top Menu of Remocon Diagnosis Menu, press

[0] button on the remote commander.

8. D.C.A.C. (AUTOMATIC ACOUSTIC FIELD CALIBRATION) TEST MODE

Procedure:

1. Press the [

] button to turn the power on.

?/1

2. Press the [FUNCTION] button to set the function “ DVD”.

3. Insert Calibration mic (ECM-AC2) supplied as an accessory into the AUDIO IN/A.CAL MIC jack.

4. While pressing the [x] and [Z] buttons simultaneously, turn the [VOLUME] control in the direction of (–).

5. Conﬁ rm that the following are shown on the display panel.

The JACK inserted/non-inserted detection display and the

STEREO/MONO detection display.

7-4-3. Clear the Initialize Setup Data

Press [DVD MENU] button and then press [CLEAR] button on the remote commander.

Emg. History Check

Laser Hours CD 999h

DVD 999h 59min

initialize setup data...

[Next] Next Page [Prev] Prev Page [O] Return to Top Menu

59min

JACK :* * * *

1

1 “NON” : Not detected

“ST” : STEREO “NOMO” : MONO

6. To exit from this mode, press the [x] and [Z] buttons simultaneously, turn the [VOLUME] control in the direction of (–).

18

HCD-FZ900KW/FZ900M

9. AMP TEST MODE

• This mode is used to measurement and test of the AMP connection.

Procedure:

1. Press the [

] button to turn the power on.

?/1

2. Press three buttons [x], [N] and [Z] simultaneously. When the this mode, blink to segments (“SA-CD” and “CAT”) on FL display.

3. Press [DISPLAY] button of the remote commander. When the this mode is displayed as “MEASURE” on FL display.

Whenever the [DISPLAY] button is pressed, the AMP test

mode changes in the following order.

MEASURE t SAFETY

MEASURE: AMP measurement mode SAFETY: AMP regulations, temperature, character mode

4. Press [MUTING] button on the remote commander. When the this mode is displayed as “VOL N” on FL display.

Whenever the [MUTING] button is pressed, the VOL test

mode changes in the following order.

VOL N t VOL M/M

VOL N: Turn the [VOLUME] control, the display is

change in succession (MIN y MAX)

VOL M/M: Turn the [VOLUME] control in the direction of

(+) is change to “MIN”, turn the direction of (–) is change to “MAX”.

5. To exit from this mode, press the [

] button to “COLD

?/1

RESET” and turn the power off.

10. DEMO PLAY MODE OUT

It is a mode to release the demonstration reproduct by the dedicated demonstration disc.

1. During playback the DEMO Disc, press the [x] and [N] buttons for ﬁ ve seconds simultaneously.

2. The message “DEMO OFF” is displayed, a mode to reproduct the demonstration is released.

11. DMPORT (DIGITAL MEDIA PORT) TEST

1. Connect the DMPORT CHECK JIG (P/N: J-2501-309-A) with the terminal DMPORT.

2. Press the [

] button to turn the power on.

?/1

3. Conﬁ rm that both LEDs of the DMPORT conﬁ rmation JIG lights. (Conﬁ rmation the power supply line.)

4. Set the [FUNCTION] button with “DMPORT” on this model.

5. Press three buttons [x], [N] and [FUNCTION] simultaneously, the DMPORT test mode is activated.

6. It is conﬁ rmed that “DMPORT OK” is displayed on this set display. (Conﬁ rmation of communication line)

7. To a pin jack of the DMPORT conﬁ rmation JIG input informa- tion relevant to audio signal (sine-wave 1.0Vrms) and composite video signal (white 100% 1.0Vp-p, color bar, etc.)

8. Conﬁ rm the output of speakers and monitor TV. (Conﬁ rmation of analog signal)

9. To exit from this mode, press three buttons [x], [N] and [FUNCTION] simultaneously.

VIDEO

AUDIO

color pattern generator

AF oscillator

DMPORT

CHECK JIG

(P/N: J-2501-309-A)

J001 7

CN451

SET

MAIN board

IO-COMPONENT

SPEAKER

board

J4001

TV

board

FL speaker, FR speaker

TB5301(FZ900KW) TB5300(FZ900M)

19

HCD-FZ900KW/FZ900M

12. PROTECTION FACTOR (SD DETECTION/ DC DETECTION) IDENTIFICATION TEST MODE

When an error is detected, the FL tube alternately displays “PROTECTOR h PUSH POWER”. r Press the [ * Buttons other than the [ “STANDBY” blinks three times on the FL tube. r The protection release state (POWER OFF) is established. (No FL tube display) r Press the [ The power to the system turns on, and the normal operation is established. (Restore)

During the protection state:

1. If the AC plug is connected or disconnected during the protection state, the protection state is released, and the normal operation is established. (The protection state is not maintained.)

2. The protection factor is displayed by pressing the [RETURN] t [3] t [2] t [0] t [0] t [ANGLE] buttons of the remote commander.

(during the “PROTECTOR h PUSH POWER” display). k When SD is detected: Repeats “SD DETECT h PROTECTOR”. k When DC is detected: Repeats “DC DETECT h PROTECTOR”.

] button.

?/1

] button two times.

?/1

] button are invalid.

?/1

PL: SD detection

When the “L” output from the SD (shutdown) port on the

S-MASTER POWER Driver Shutdown and voltage descent (15V or less) of 30V power supply (PVDD) are detected.

DC detection

When the “L” output from the power/speaker error detection

circuit (DC detection port) is detected for two seconds continually, the power system other than that of the FL tube is turned off, and the protection state is established.

20

SECTION 4

ELECTRICAL ADJUSTMENTS

DVD SECTION

When the optical pick-up assy is replaced, perform the “EXECUTING IOP MEASUREMENT”.

EXECUTING IOP MEASUREMENT (See page 16)

TUNER SECTION

[FM Tune Level Check]

generator

HCD-FZ900KW/FZ900M

SET

Procedure:

1. Turn the power on.

2. Input the following signal from Signal Generator to FM antenna input directly.

* Carrier Freq : A = 87.5 MHz, B = 98 MHz, C = 108 MHz Deviation : 75 kHz Modulation : 1 kHz ANT input : 35 dBu (EMF)

Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You

cannot use video cable for checking.

Please use SG whose output impedance is 75 ohm.

3. Set to FM tuner function and tune A, B and C signals.

4. Conﬁ rm “TUNED” is lit on the display for A, B and C signals.

FM ANTENNA

OUT (75 :)

The mark of “TUNED” means “The selected station signal is received in good condition.”

21

HCD-FZ900KW/FZ900M

SECTION 5

DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)

For Printed Wiring Boards.

Note:

• X : Parts extracted from the component side.

• a : Through hole.

• : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

Caution:

Pattern face side: (SIDE B) Parts face side: (SIDE A)

• Indication of transistor.

C

Q

B

E

CEB

• Abbreviation AUS : Australian model EA : Saudi Arabia model E3 : 240V AC area in E model E12 : 220 – 240V AC area in E model E15 : Iran model E32 : 110 – 240V AC area in E model RU : Russian model SP : Singapore model TH : Thai model

These are omitted.

Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.

These are omitted.

For Schematic Diagrams.

Note:

• All capacitors are in μF unless otherwise noted. (p: pF) 50

WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

speciﬁ ed.

• f : internal component.

• C : panel designation.

Note: The components identiﬁ ed by mark 0 or dotted

line with mark 0 are critical for safety.

Replace only with part number speciﬁ ed.

• A : B+ Line.

• B : B– Line.

• Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.

• Voltages and waveforms are dc with respect to ground in service mode.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal production

tolerances. no mark : TUNER (FM)

< > : DVD PLAY * : Impossible to measure

• Voltages are taken with VOM (Input impedance 10 MΩ).

• Circled numbers refer to waveforms.

• Signal path.

F : TUNER J : DVD PLAY L : VIDEO E : Y a : CHROMA r : COMPONENT VIDEO N : MIC

• Abbreviation

AUS : Australian model EA : Saudi Arabia model E3 : 240V AC area in E model E12 : 220 – 240V AC area in E model E15 : Iran model E32 : 110 – 240V AC area in E model RU : Russian model SP : Singapore model TH : Thai model

• Circuit Boards Location

P-LED board

MS-203 board

22

IO-COMPONENT board

SCORE board

FL-JACK board

KEY-SW board

J-LED board

S-AIR-CON board (FZ900M)

S-AIR-INC board (FZ900KW)

SPEAKER board

DSP board

MAIN board

POWER board

U-LED board

USB board

5-1. BLOCK DIAGRAM – RF Section –

RF

VOA/A

DETECTOR

OPTICAL PICK-UP

BLOCK

(KHM-313CAA)

LASER DIODE

(FOR CD)

LASER DIODE

(FOR DVD)

VOB/B

VOC/C

VOD/D

VOE/E+G

VOF/F+H

LD (780)

LD (650)

VR (650) VR (780)

A

B

C

D

A

B C D

VC

Q1102 (1/2)

LD DRIVE

CONTROL (FOR CD)

PD

Q1102 (2/2)

LD DRIVE

CONTROL (FOR DVD)

Q1101

PD VOLUME

CONTROL

DVDRFIP

10

DVDA

6

DVDB

7

DVDC

8

DVDD

9

TNI

17

TPI

18

NA

11

NB

12

MC

13

MD

14

V20 (2.0V)

28

LD01

22

MDI1

19

MDI2

20

LD02

21

MSW

54

IC1101 (1/2)

CD/DVD RF AMP,

FOCUS/TRACKING ERROR AMP,

DVD SYSTEM CONTROL, DSP

V2REFO (2.8V)

RXD TXD

VBUS_OC

USB_DM

USB_DP

VBUS_OE

ACLK

ALRCK

ABCK

ASDATA2

ASDATA1

ASDATA0

27 105 106

VBUS OVER CURRENT DETECT

197 1

45

44

196

203

205

204

223

225

226

VBUS_SW

IC2101

POWER

L

SECTION

(Page 28)

HCD-FZ900KW/FZ900M

CN1105

6

RFMON

5

V2REFO

RXD TXD

USB 5V

CN5200

SECTION

(Page 26)

(SERVICE JIG)

DSP

2 1

2 3

VBUS

1

D-

2

D+

3

GND

4

ACLK

ALRCK

ABCK

AMP_D02

AMP_D01

AMP_D00

A

2AXIS DEVICE FOCUS/

TRACKING

COIL

MSW

VCC

FCS+

FCS-

TRK+

TRK-

REG02

REG01

(SLED MOTOR)

(SPINDLE MOTOR)

Q1103

MM

SP+ SP-

SLSL+

10P

IC1201

FOCUS/TRACKING DRIVER,

LOADING/SPINDLE/SLED MOTOR DRIVER

42 41

36 37

35 34

32 31 30 29

27 28

46 47

BUFFER

FOCUS COIL

DRIVE

TRACKING COIL

DRIVE

BUFFER

SLED MOTOR

DRIVE

SPINDLE MOTOR

DRIVE

BUFFER

MCS

IC503 (1/6)

(LIMITSW)

LIMITSW

53

FMO FOO

DMO TRO

39

IOPMON

VREFO [1.4V]

29

FMO

37

FOO

41

DMO

36

TRO

40

FWD

94

REV

95 38

TROPENPWM

OP_INP

35

MUTE123

157

MUTE

158

TSD_M

130

40

43

48

1

12

3 4

9 10 13 16 17 15

6

7 45 19 20 22 21

25 24

VREFO

FOO

TRO

FMO

DMO

SPFG

XSYSRST

IFCK

IFSDO

IFSDI

XIFCS

KRMOD

MIC

OCSW

IFBSY

CKSW

108

98

97

100

99 213 208 104

110

103

XSYSRST

IFSCK

IFSDO

IFSDI

XIFCS

KRMOD

MIC

45

49

48 47 51 53 52 44

50

XSYSRST

SYSTEM CONTROL

DVD RST

DVD_SCO

DVD_SOD DVD_SID DVD XIFCS KMODE TV_SEL/MIC_DET_OUT/LED_LAT CDM_OPEN_SW

DVD_XIFBUSY

VIDEO

C

SECTION

(Page 24)

OCSW1/REVOCSW

CKSW/FWDCKSW

(CHUCK/TRAY DETECT)

LDM+

LDM-

S001

M

• SIGNAL PATH

M001

(LOADING MOTOR)

: TUNER

: DVD PLAY

HCD-FZ900KW/FZ900M

2323

HCD-FZ900KW/FZ900M

5-2. BLOCK DIAGRAM – VIDEO Section –

IC503 (2/6)

SYSTEM CONTROL

CEC_RX_IN

CEC_TX_OUT

6

26

82V_SEL1 81V_SEL0 83V_SEL2

72HDMI_PCONT

191Y 189C

185Y/G 183B/Cb/Pb 182R/Cr/Pr

180TX2P 179TX2N 177TX1P 176TX1N 174TX0P 173TX0N 171TCKP 170TCKN

162HTPLG

CEC_RX_IN

CEC_TX_OUT

IC1103

EEPROM

WFEEWP

SCL6SDA

7

AUDIO

SECTION

VIDEO

B

(Page 25)

V_SEL1 V_SEL0 V_SEL2

IC4002

VIDEO DRIVER

5YC MIX

13 MUTE2

3MUTE1

6YIN 2CIN 4 CVBSIN

10 CVIN 12 CBIN 14 CRIN

2

4

IC1705

BUFFER

5

1

+6V

IC1707

+5V REG.

23CVBSOUT

20CYOUT

18CbOUT

16CrOUT

Q1701

LEVEL SHIFT

VOUT

CYOUT

CBOUT

CROUT

CEC_RX_IN CEC_TX_OUT

Q9724,9726, Q9728,9729 CEC RX/TX INTERFACE

J4001 (1/2)

J4000

CN1701

1 3 4 6 7

9 10 12

19

18

13

15 16

VIDEO OUT

Y

PB/CB

PR/CR

TMDS DATA2 + TMDS DATA2 – TMDS DATA1 + TMDS DATA1 – TMDS DATA0 + TMDS DATA0 – TMDS CLOCK + TMDS CLOCK –

HPD

+5V POWER

CEC

SCL SDA

COMPONENT

VIDEO OUT

HDMI OUT

SECTION

(Page 25)

HCD-FZ900KW/FZ900M

AUDIO

112 101 102

SCL

SDA

SCORE/DIR_XSTATE

XVOICE/DIR_CSFLAG

Rt/DIR_DI

198

SCORE

XVOICE

D

MUSIC

Lt/DIR_DO

214

230

231

RF

SECTION

IC1101 (2/2)

DVD SYSTEM CONTROL, DSP

XSYSRST

C

12

79,80,82–86,89

HD0–HD7

29,31,33,35,

38,40,42,44

DQ0–DQ7

RESET

HD0–HD7

HA0–HA21

56–64,67–75,77,

A0–A21

A0

25–16,10–1,48

A0–A19,NCDQ15/A-1

IC1102

FLASH ROM

87,91,92

A1–A21

XRD

XROMCS

76

XWR

11OE28CE2645

XWR66XRD78XROMCS

2,4,5,7,8,10,11,13,42,

WE

44,45,47,48,50,51,53

161

RD0–RD15

117–113,119–129

RD0–RD15

159

DDC_DA

DDC_CLK

RA0–RA11

139–141,143,144

149–155

22–26,29–35

A0–A11

IC1104

SDRAM

BA0

138

137

135

133

136

146

147

132

111

134

CKE

DQM1

DQM0

_CAS

_RAS

_RWE

_RCS

DRCLK

BA1

• SIGNAL PATH

: VIDEO

20

/CS

/WE

BA121BA0

CLK

/RAS

/CAS

LDQM

UDQM

CLKE

: Y

: CHROMA

37

39

15

17

18

16

19

38

: COMPONENT VIDEO

(Page 23)

2424

5-3. BLOCK DIAGRAM – AUDIO Section –

FZ900M

J5001

MIC2

Q5007,5009,5012 MIC DC SWITCH

J5000

FZ900M

AUDIO IN/MIC/

A.CAL MIC

AUDIO IN/MIC1/

A.CAL MIC

PLUG_DET

D5008

MO/ST_DET

FZ900KW

SW3.3V

Q5004,5005,5011 MIC DC SWITCH

IC5004

MIC AMP

3 1

5 6

IC5003

MIC AMP

Q5010

7

MIC2

F-AUDIO (R)

F-AUDIO (L)/MIC1

R-CH

DC_CONT

GAIN_CONT

IC4008

ELECTRONIC VOLUME

8

VIN2

1

VIN1

4

DATA

5

CLK

INPUT SELECT

5 3

2

4

1

OUT2

OUT1

IC4007

Y1 Y

Y2

Y3

Y0

HCD-FZ900KW/FZ900M

IC4202

ALC

SCORE DETECT

2 3

6 5

Q4201,4202

SCORE

DETECT

8

6

4

D4008

1

SCORE

7

XVOICE

D

VIDEO

SECTION

(Page 24)

MUSIC

IC4201

AF AMP

A+9V

D4203,4204

2

IC4010

ALC EQ AMP

5

MIC1+2

7

2

L-IN

R-IN

R-CH

Q4012

10

A

Q4011

9

B

ASEL0

ASEL1

E

(Page 26)

3

MUSIC

DSP

SECTION

7

D4201

D4202

1

Q5006,5008

MIC GAIN CONTROL

J4001(2/2)

L

IN

R

J4002

L

IN

R

17

13 14

5 6

7

2 4

TU4001

FM

TUNER

PAC K

VIDEO

LCH RCH

RXD TXD DET

VBUS (5V)

VIDEO 5V

R-CH

L-CH

R-CH TUNED DI

DO CK CE

RDS_DATA RDS_CLK

VIDEO

R-CH

FZ900M

VIDEO 5V

(DMPOART)

R-CH

B

(Page 24)

VIDEO

SECTION

DMP_TXD DMP_RXD DMP_DET

IC451

DMPOART

AUDIO AMP

3 1

R-CH

Q4013Q4014

DI

CK

SAT/

CABLE

AUDIO

CN451

DMPORT

DIGITAL

MEDIA PORT

ANTENNA

75Ω FM

COAXIAL

TV

INPUT SELECT

5 3

2

4

1

INPUT SELECT

5 3

2

4

1

FZ900KW

AMP

SECTION

(Page 27)

IC4005

Y1 Y

Y2

Y3

Y0

IC4004

Y1 Y

Y2

Y3

Y0

F

10

A

9

B

10

A

9

B

PLUG_DET

Q4010

Q4009

Q4008

Q4007

+

DMP_DET

ASEL2

ASEL3

ASEL4

ASEL5

ASEL0 ASEL1 ASEL2 ASEL3 ASEL4 ASEL5

PLUG_DET

MO/ST_DET

GAIN_CONT

A.CAL DC_CONT

DMP_TXD

DMP_RXD

TUNED DI

DO CK

CE

RDS_DATA RDS_CLK

FZ900M

L-CH

R-CH

84 85 86 87 88 89

65

90

43 91 42

35 36

80 77 78 79 76

74 75

R-CH

DSP_MASTER

IO_CE/ASEL0 IO_RESET/ASEL1 IO_DI/ASEL2 IO_DO/ASEL3 IO_CLK/ASEL4 ASEL5

JACK1/JACK2/S-ART DET

MONO/ST_DET

MIC_GAIN A.CAL MIC LEVEL/DSP_MASTER DC_CONT

DMP_TX_OUT DMP_RX_IN

TUNED ST_DI/MIC_DATA ST_DO ST_CLK/MIC_CLK ST_CE

RDS_DATA RDS_CLK

DSP

G

SECTION

(Page 26)

IC503 (3/6)

SYSTEM CONTROL

• R-ch is omitted due to same as L-ch.

• SIGNAL PATH

: TUNER

: VIDEO

: MIC

HCD-FZ900KW/FZ900M

2525

HCD-FZ900KW/FZ900M

5-4. BLOCK DIAGRAM – DSP Section –

TV DIGITAL IN

AUDIO

SECTION

(Page 25)

RF

SECTION

(Page 23)

FZ900M

CN103

EZW-T100

S-AIR

TRANSMITTER

COAXIAL

OPTICAL

L-IN

E

R-IN

ACLK ALRCK ABCK AMP_D00

A

AMP_D01 AMP_D02

4

2 26

16 15

24 14 23 25

12

19 18

11

7

• SIGNAL PATH

: TUNER

LCH RCH

SD2 SD1 BCK1 BCK2 LRCK1 LRCK2 GND

ADC_SEL I2C_SDA I2C_SCL RESN

GPIO2

J501

IC502

OPTICAL

RECEIVER

DET

RESET

SDTO

IC700

DSP

Lt/Rt DPSOE DAI_P10 FL/FR DPSOA DAI_P6

SL/SR DPSOB DAI_P7

C/SW DPSOC DAI_P8

DPDVBCK DAI_P17

DPDVRCK DAI_P16

SPI_MAS DAI_P15

FLAG0 INT_REQ FLAG1 DIR_ERR

24

25 26

24

25 26

MOSI MISO

SPICLK

CLKIN

XTAL

SF_CE FLAG3

SPIDS

RESET

77 64 65 70 87

86

127 126

125

142

143

63 98 15

16 122 121

IC808

DATA SELECT

1A 2B

EEPROM

X700

25MHz

Y

A/B

IC706

5

6

SD

SCK

CE

SPICLK

ADC_SEL

RESET

7

2 1

SI

IC705

AND GATE

2 5 6 1

VCC+3.3V

(S-AIR-INC)

AMP_DMIX

AMP_D1 AMP_D2 AMP_D3

BCKO

LRCKO

MCKO

5 6

3

SDIN_B (Surr)

SDIN_A (2nd)

SDIN_C

BCK LRCK

I2C_SDA

I2C_SCL

DET INT

RESET VCC_3.3V

AMP

J

SECTION

(Page 27)

Q700

DELAY

IC703

DATA LATCH

1

D CLK

2

IC702

BUS BUFFER

3 5

6

IC701

DATA SELECT

5

SF_MASTER

SF_CE

13

20

TRANSCEIVER

19

17 15

14

11

3 7

12

2

4

Q

7

2

1

2

6

FZ900KW

CN803

EZW-RT10

S-AIR

DIR_XSTATE

DSP_MISO

DSP_MOSI

DSP_SPICLK

DSP_SF_CE

DSP_MASTER

DIR_XSTATE

DIR_ERR

DIR_CE DIR_DO CSFLAG DIR_RST DIR_ZERO SACD_SEL

INT

RESET DET ADC_SEL I2C_SDA I2C_SCL

IC503 (4/6)

SYSTEM CONTROL

DSP_MISO

22

DSP_MOSI

24

DSP_SPICLK

23

DSP_SF_CE

21

68

A.CAL_OUT/DSP_INTR

DSP_SPIDS25 DSP_RESET

27

17

DIR_XSTATE

10

DIR_ERR

70

DIR_HCE/eHDMI_SEL

100

DIR_HDOUT

19

DIR_CSFLAG

11

DIR_RST

18

DIR_ZERO

69

SACD_SEL

33

S-AIR_GPIO2/CLK1

37

S-AIR_RST/C_SW_SEL

34

S-AIR_DET/RST1

38

S-AIR_ADC_SEL/DRIVER_C_EN

30

E2P_SDA/S-AIR_SDA

29

E2P_CLK/S-AIR_CLK

IC505

EEPROM

5

SDA

6

SCL

IC304

IC501 WAVE

SHAPE

X301

24.576MHz

INT

5

21

22

42

13 VINL 14 4A

14 VINR

12.288kHz

L-CH R-CH

DIN2 (I) (COAX)

XOUT (O)

XIN (I)

DIN (I) (OPT)

A/D CONVERTER

DSP_MASTER

X800

DIR

AUDIO (O)

24

DATA (O)

16

XMODE (I)

48

CL (I)

38

CE (I)

37

DI (I)

36

DO (O)

35

ERROR (O)

BCK (O)

LRCK (O)

CKOUT (O)

SCKI

LRCK

BCK

DOUT

IC802

2A

532Y 63A

34 25 17

14 15 13

3Y

CSFLAG (O)

XSTATE (O)

IC303

L-CH R-CH SD2 SD1 BCK

LRCK

CLOCK GENERATOR

DIR_ZERO

DIR_RST DIR_CLK DIR_CE

DIR_DIN DIR_DO DIR_ERR CSFLAG DIR_XSTATE

6

7

8

9

DSP_MASTER

AUDIO

G

SECTION

(Page 25)

AMP

I

SECTION

(Page 27)

SD2 (SL/SR)

SD1 (DMIX) BCK LRCK

2

DIR_CLK

DIR_DIN

SACD_SEL

IC807

A/D CONVERTER

SCKI

6

VINL

13

VINR

14

DOUT

BCK

LRCK

H

(Page 27)

IC306

SACD SELECT

1A/B

13 4B 11 3A 10 3B

52A 62B 21A 31B

SI_C SI_D

9 8 7

AMP

SECTION

4Y

3Y

2Y

1Y

NONAUDIO FLAG2

SI_A

12

LRCK

9

BCK

7

4

97

DSPIA DAI_P11

78

DPFSCK DAI_P20

94

DPLRCK DAI_P18

88

DPBCK DAI_P19

89

SI_B

LPCM FL/FR

79

DPSIB DAI_P12

LPCM SBL/SBR

82

DPSIE DAI_P15

LPCM SL/SR

80

DPSIC DAI_P13

LPCM C/SW

81

DPSID DAI_P14

IC805

SAMPLE RATE CONVERTER

9SDIT

8IBICK 7 ILRCK

18 IMCLK

4

SMUTE

3PDN

SAMPLE RATE CONVERTER

9SDIT

8 BICK 7 ILRCK

18 IMCLK

4SMUTE 3PDN

OBICK

OLRCK

IC806

OBICK

OLRCK

HCD-FZ900KW/FZ900M

2626

5-5. BLOCK DIAGRAM – AMP Section –

(Page 26)

AMP_D1 AMP_D3 AMP_D2

AMP_D3

J

: TUNER

BCKO

LRCKO

MCKO

AMP_DMIX

BCK

LRCK

SD1

SD2

IC503 (5/6)

SYSTEM CONTROL

I

SECTION

(Page 26)

71HP_MUTE/S_AIR_Rcv_SEL

1DAMP_SCDT/DIR_DIN

2DAMP_SHIFT/DIR_CLK 59DAMP LAT1 60DAMP LAT2 61DAMP LAT3 57DAMP INIT 58SOFT MUTE 55OVERFLOW1 56OVERFLOW2

54DRIVE RST(EN)

67SD(DIAG)/PVDD_DET

66DC_DET

DSP

SECTION

(Page 26)

• SIGNAL PATH

DSP

SECTION

DSP

HPMUTE

SOFTMUTE

SD_PVDD_DET

DIR_CLK SHIFT DIR_DIN SCDT

H

SCDT

SHIFT

LAT1 LAT2 LAT3

NS_INIT

OVF1 OVF2

EN

DC-DET

AUDIO

SECTION

(Page 25)

HCD-FZ900KW/FZ900M

IC3001

HEADPHONE AMP

3 2

5 6

IC3030

S-MASTER PROCESSOR

DATA

MCK0 BCK0 LRCK0

OVF2 SCDT SHIFT LAT3 NS_INIT

SOFTMUTE

AMP_D1

MCK0 BCK0 LRCK0

OVF1 SCDT SHIFT LAT1 NS_INIT

SOFTMUTE

AMP_D2

MCK0 BCK0 LRCK0

SCDT SHIFT LAT2 NS_INIT

SOFTMUTE

PLUG_DET

F

FZ900KW

31

36 XFSIIN 30 BCK 29 LRCK 25 OVF FLAGL 24 OVF FLAGR 21 SCDT 22 SCSHIFT 23 SCLATCH 27 INIT

19 SOFTMUTE

IC3010

S-MASTER PROCESSOR

31

DATA

36 XFSIIN 30 BCK 29 LRCK 25 OVF FLAGL 24 OVF FLAGR 21 SCDT 22 SCSHIFT 23 SCLATCH 27 INIT

19 SOFTMUTE

IC3020

S-MASTER PROCESSOR

DATA

31

36 XFSIIN 30 BCK 29 LRCK 25 OVF FLAGL 21 SCDT 22 SCSHIFT 23 SCLATCH 27 INIT

19 SOFTMUTE 24 OVF FLAGR

Q3552 – 3555

B+ DOWN PROTECT

Q502,503

BUFFER

OUTR1(+)

6

4OUTR2(–)

9OUTL1(–)

11OUTL2(+)

38FS0I

48XFS0IN

43HPOUTL2

45HPOUTL1

39HPOUTR2

41HPOUTR1

6

4OUTR2(–)

11OUTL1(+)

9OUTL2(–)

37FS0CKOUT 38FS0I

48XFS0IN

14XFS0OUT

FZ900KW

6

4OUTR2(–)

11OUTL1(+)

9OUTL2(–)

38FS0I

48XFS0IN

14XFS0OUT

D3552

EN

WF

C

HP

FR

FL

IC3051 CLOCK

OSCILLATOR

X3051

49.1MHZ

SR

SL

+31V

POWER

K

SECTION

(Page 28)

FZ900M

1

7

L

R

16 PWM_B

8 PWM_A

76/RESET

IC3400

DIGITAL POWER AMP

16 PWM_B

8 PWM_A

76/RESET

IC3300

DIGITAL POWER AMP

16 PWM_B

8 PWM_A

76/RESET

IC3100

DIGITAL POWER AMP

16 PWM_B

8 PWM_A

7

/RESET

IC3150

DIGITAL POWER AMP

8 PWM_A

16 PWM_B

7

/RESET

IC3200

DIGITAL POWER AMP

16 PWM_B

8 PWM_A

7

/RESET

IC3250

DIGITAL POWER AMP

8 PWM_A

16 PWM_B

7

/RESET

Q3551

DC BALANCE

PROTECT

PLUG DET

HPMUTE

OUT_B

OUT_A

SD

OUT_B

OUT_A

SD

OUT_B

OUT_A

SD

OUT_B

OUT_A

SD

6

OUT_A

OUT_B

SD

6

OUT_B

OUT_A

SD

6

OUT_A

OUT_B

SD

6

Q3081

H/P MUTE

DRIVE

31

-

33

34

-

36

IC3500

DIGITAL POWER AMP

D3551

31

-

33

34

-

36

31

-

33

34

-

36

31

-

33

34

-

36

34

-

36

31

-

33

31

-

33

34

-

36

34

-

36

31

-

33

M+14V

LPF

Q3251,3252

DC BALANCE

DETECT

Q3301,3302

DC BALANCE

DETECT

Q3101,3102

DC BALANCE

DETECT

Q3151,3152

DC BALANCE

DETECT

Q3401,3402

DC BALANCE

DETECT

Q3202,3201

DC BALANCE

DETECT

Q3000 – 3002

FAN

DRIVE

Q3116—3119

MUTE

TB3901

TB5300

TB5301

FAN3001

DC FAN

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

FZ900KW

J5001

PHONES

SUBWOOFER

CENTER

FRONT R

FRONT L

FRONT R

FRONT L

SUR R

SUR L

SPEAKER

FZ900KW

SPEAKER

FZ900M

HCD-FZ900KW/FZ900M

2727

HCD-FZ900KW/FZ900M

5-6. BLOCK DIAGRAM – POWER Section –

S5501

VOLUME

S5500

OPERATION

DIAL



S5109

/

D5400

!/

D5601

KEY

ILLUMINATION

D5501—5503

KEY

ILLUMINATION

E4V

S5400

!/

IC506

RESET

REMOTE

CONTROL

RECEIVER

S5100—5102

LED DRIVER

IC5002

ROTARY SWITCH

S5103,5600

FUNCTION

KEY

FUNCTION

KEY

Q5400

Q5600

Q5500

D501

Q501

RESET

X501

5MHz

SYSTEM CONTROL

94 KEY2

95 KEY1

97 KEY0

73 KEY_INT

28 LED_PWM

12 RESET

20 AC CUT

4 SIRCS_IN

Xout

13

15

Xin

IC503 (6/6)

FL_CS

T5000

DC/DC

D5000

IC5001

FL DISPLAY

DRIVER

30VEE

7FL_CLK/LED_CLK 5FL_D_OUT/LED_DATA 3

39P.CONT1

41WRITE EMP P_CONT3

8CLK 7DIN 9STB

P.CONT1

RF

SECTION

(Page 23)

S2 – 16

G1 – 12

L

15

–

29

42

–

31

1LED1 2LED2 3LED3

VBUS_SW

(DMPORT)

D5002

+3.3V-3

(IC1101)

RF+3.3V

(IC1101)

+3.3V-2

(IC1101)

+3.3V-1

(IC1101)

+1.8V

(IC1101)

USB 5V

VIDEO+5V

+5V

+1.2V (DSP)

D3.3V

+1.8V

(D-AMP)

+3.3V

(IC5001)

LED+5V

5V

(FL)

D5001

F1 F2

CONVERTER

TRANSFORMER

ND5000

FLUORESCENT

INDICATOR

TUBE

Q5001,5002,5601

LED DRIVER

IC1105

+3.3V REG.

IC1107

+3.3V REG.

IC1708

+3.3V REG.

IC1110

+1.8V REG.

IC509

+5V REG.

IC707

+1.2V REG.

IC3050

+1.8V REG.

IC5000

+3.3V REG.

Q5000

5V (FL)

IC452

+5V REG.

IC507

+5V REG.

IC510

+3.3V REG.

IC504

+5V REG.

IC508

+5V REG.

DC/DC

CONVERTER

D5003

MOVIE

D5004

MUSIC

D5600

REC TO USB

M+14V

M+9V

(VIDEO)

A12V

+9V

+5V

+6V

(S-AIR-CON)

+3.3V

(S-AIR-INC)

F945

E4V

E3.3V

+4V

AMP

SECTION

(Page 27)

P.CONT1

M+9V

IC4009

+9V REG.

IC4003

+5V REG.

D503

Q100,101

B+ SWITCH

K

M+14V

12V

E+4V

FZ900M

IC800

+3.3V REG.

+31V

(DIGITAL AMP)

EN

6V

IC941

+12V REG.

Q945

B+ SWITCH

PS956

PS954

P.CONT3P.CONT3

IC932

SHUNT REG.

Q943,947

POWER DOWN

DETECT

Q949,950

POWER

PROTECT

SHUNT REG.

CONTROL

D931

D912

D916

D911

D947

IC923

Q930

POWER

T901 MAIN

TRANSFORMER

PC901

FEED BACK

PC903

STANDBY

CONTROL

T903 SUB

TRANSFORMER

FEED BACK

STANDBY

CONTROL

PC902

PC904

D902

D905

D901

POWER CONTROL

D914

Q922

+21V REG.

Q921

Q901

Q951

OVER CURRENT PROTECT

E32 MODEL

DZ904

D923

D906

LF901,902

FILTER

IC901

SWITCHING

REGULATOR

3D

4VCC

2GND

5FB/OLP

1 OCP/SYNC

IC921

SWITCHING

REGULATOR

7VIN 9D

4VCC

2FB

1ZC

F901

(AC IN)

HCD-FZ900KW/FZ900M

VCC+3.3V

(S-AIR-INC)

IC804

+3.3V REG.

FZ900KW

2828

• Waveforms

HCD-FZ900KW/FZ900M

– MAIN Board – – IO-COMPONENT Board –

 IC1101  (DVDRFIP)

200 mV/DIV, 100 ns/DIV

 IC1101 [Y (R/Cr/Pr)

H

200 mV/DIV, 20 μs/DIV

 IC1101 [D (B/Cb/Pb)

650mVp-p

0.72Vp-p

 IC1101 YD (XTALO)

27MHz

500 mV/DIV, 20 ns/DIV

 IC503 RE (Xout)

5MHz

1 V/DIV, 100 ns/DIV

 IC304 RE (CKOUT(O))

RE IC3051  (3Y)

1.6Vp-p 5Vp-p

1 V/DIV, 10 ns/DIV

49.1MHz

RG IC3010 SL (XFSOIN)

3.4Vp-p

49.1MHz

1 V/DIV, 10 ns/DIV

4.3Vp-p

RH IC3010 RG (XFSOOUT)

3.5Vp-p

 IC4002  (Cin)

H

500 mV/DIV, 20 μs/DIV

 IC4002  (Yin)

H

500 mV/DIV, 20 μs/DIV

 IC4002  (CYin)

1Vp-p

 IC4002 RI (Cr OUT)

H

500 mV/DIV, 20 μs/DIV

 IC4002 RL (Cb OUT)

H

500 mV/DIV, 20 μs/DIV

 IC4002 X (CY OUT)

2Vp-p

1Vp-p

2Vp-p

– S-AIR-INC Board –

1 IC802 5 (2Y)

12.288MHz

1 V/DIV, 20 ns/DIV

2 IC807 7 (LRCK)

20.8Psec

1 V/DIV, 10 Ps/DIV

3 IC807 8 (BCK)

3.2Vp-p

H

200 mV/DIV, 20 μs/DIV

 IC1101 [C (Y/G)

500 mV/DIV, 20 μs/DIV

 IC1101 [ (C)

H

500 mV/DIV, 20 μs/DIV

 IC1101 [[ (Y)

H

0.72Vp-p

1Vp-p

40.7nsec

1 V/DIV, 20 ns/DIV

 IC304 RG (BCK(O))

163nsec

1 V/DIV, 50 ns/DIV

RB IC304 RH (LRCK(O))

10.4μsec

1 V/DIV, 5 μs/DIV

RT IC304 XB (XOUT(O))

3.5Vp-p

4Vp-p

49.1MHz

1 V/DIV, 10 ns/DIV

– DSP Board –

 IC700 [WD (XTAL)

0.5 V/DIV, 20 ns/DIV

25MHz

4Vp-p

1.8Vp-p

H

500 mV//DIV, 20 μs/DIV

 IC4002 RT (Cb in)

H

200 mV/DIV, 20 μs/DIV

 IC4002 RG (Cr in)

H

200 mV/DIV, 20 μs/DIV

0.72Vp-p

H

1 V/DIV, 20 μs/DIV

 IC4002 XE (CVBS OUT)

H

1 V/DIV, 20 μs/DIV

2.6Vp-p

3.2Vp-p

0.326Psec

1 V/DIV, 0.1 Ps/DIV

4 IC805 3 (PDN)

IC806 3 (PDN)

3.2Vp-p

160msec

1 V/DIV, 50 ms/DIV

5 IC805 7 (ILRCK)

IC806 7 (ILRCK)

3.2Vp-p

20.8Psec

1 V/DIV, 10 Ps/DIV

6 IC805 8 (IBICK)

IC806 8 (IBICK)

500 mV/DIV, 20 μs/DIV

HCD-FZ900KW/FZ900M

H

1 V/DIV, 20 ns/DIV

24.576MHz

0.326Psec

1 V/DIV, 0.1 Ps/DIV

3.2Vp-p

2929

HCD-FZ900KW/FZ900M

5-7. PRINTED WIRING BOARD – MAIN Section (1/2) –

R453

CL327

R328

FZ900M

R507

R510

R512

C457

L451

R1246 R1247

2

CN1202

4

IO-COMPONENT

BOARD CN4003

(Page 42)

(KHM-313CAA)

MS-203 BOARD

CN001

(Page 31)

FZ900KW

IO-COMPONENT

BOARD CN4006

(Page 42)

FZ900M

IO-COMPONENT

BOARD CN4007

(Page 42)

K

DVD DRIVE

(1/2)

OPTICAL

( )

PICK-UP

D

J

I

(17P)

CN472

(17P)

CN503

(19P)

CN504

JL453

C452

R465

R451

IC451

1

5

R327

C526

IC504

C451

JL451

C461

C453

R456

R452

14

85

C456 R454

R462

C1222

C1221

CL304

CL348

CL349

19

18

17

16

CN503CN504

2

1

IC505

58

C520 R569

46

C516

CN451 CN1701

DMPORT HDMI OUT

IC1707

C1727

C1729

3

54

IC1708

R1159

R1161

R2187 R1146

R1184

C1113 R1123

R1107

R1110

D501

R536

C514

C515

JL524

1

45

C1731

C1153

C1152

C1147 C1139 C1138 C1137 C1135

R1124

R1109

R346

R540

R543

R532

R544

IC503

JL523

R626

C1732

R535

CL529

R1160

R1183

C1148

CL528

JL522

R1758

3

13

1

R1743

IC1705

R2101

193

R1185

R2168

R1142

R2167

256

C1133 C1132 R1136

CL1116

1

22 4

R531

R533

R534

JL501

R577

R627

R621

IC508

R622

R620

D505

C1730

O

C1734 C1733

C1183

R2116

X1101

IC1105

45

C1182 R1151

C1193

45

R1121 R1120 R1118 R1115 R1113 R1112

R1114

R1216

R1204

R1207

Q1102

C1206

CL2103

R1209

CL1201

C1205

R1208 R1225 R1220

R344

R347

R537

R538

R539

R546

R547

100 81

JL506

180

R564

R565

JL526

JL527

30 51

JL528

JL525

R592

R571

R558

1

2

R2135

13

R1219 C1210 R1224

I

FB2124

FB2125

FB2122

C1186

R1212

JL518

R570

C1198

FB2121

FB2120

C1195

C1208

R1210

C1203

R1215

R1214

C1211

JL510

JL520

18

C462

R466

JL454

R457

C1223

C1219

C1224

IC303

R514

R516

R518

R520

R523

14

13

JL452

R460

24

2536

37

R1233

C1215

R343 R345

17

14 8

JL532

JL531

19

18

C521

CN451

IC1201

CL1207

CL1208

R302

R308

R403

R596

R598

C523

R552

R553

C1214

CL1206

R1230

R1228

R1231

R348

C310

C309

C308

R301

JL530

JL529

R597

C525

IC506

JL508

D502

C524

17

16

CN472

2

1

R1186

C1184

R1192

C1192

IC1107

R1222

R1227

C1213

13

12

1

48

R1206

C1212

R1223

CL1213

R1221

R333

JL507

JL509

JL517

R306

Q501

EB

R599

R554

C522

CN507

(19P)

CN507

FL-JACK

C

IC1110

R2111 R2112

CL1205

CL1204

R1226

C1233

C1209

JL511

JL519

C527

R555

BOARD CN5001

(Page 54)

• : Uses unleaded solder.• See page 22 for Circuit Boards Location.

MAIN BOARD (SIDE A)

CN1701

2854

IC1104

1

R1117

Q1101

C2103

R2192

R372

24

13

R342

C319

R330 R341

R574

C1110

IC1102

CL2108

R1111

C2101

85

14

R2193 R2194

R370

X301

R371

R368

R366

R367

R374

N

27

1

2548

24

R2195

C327

C326

R369

29

1

DSP

BOARD

CN701

(Page 44)

R1752

R1742

C1725

45

164

C1120

C1121

CL1115

C1101

CN1101

CL1112

JL505

JL512

5031

R618

4

5

C533

C1122

1

L1701

CL1118

CL1114

JL502

C517

JL516

C1123

CL1113

JL513

L1702

CL1101

C1124

CL1117

JL521

13

L1703

L1704

IC1101

23

CL1305

JL503

JL504

R556

JL515

C542

CL1303

19

Q1701

64

CL1304

D503

SL501

CL1302

CL1301

RB1114

CL1105

CL1108

31

R2110

R1747

R1748

RB1103

RB1111

RB1104

R2114

RB1115

129192

RB1109

128

RB1110

RB1113

RB1112

R1156

R2115

JL1160

CL2101

CL2102

CL1121

65

C1136

CL1110

CL2107

CL2109

EB

Q1103

R2127

R2128

R2121

R2123

L2101

FB2102

R1108

R1116

IC2101

R2191

R398

R397

R396

R364 R362

R391

R390

R358

C332

16

18

C328

IC306

R619 R617 R616

R625

R613

R610 R611

R615

R395

C330

R394

2536

37

R361

IC304

48

12

1

C321

R336

R337

R338

C318

R340

CL345

CL343

CL344

R407R408

R405 R406

9

R384

R356

JL471

Q9728

CN305

RB1106

RB1105

EB

Q9724

TP3006

D9712

R9935

JL3062

30

2

R9941

EB

LP301

CL1702

R9945

EB

Q9729

R9934

Q9726

R9924

C3092

FZ900KW

C9972

C3083

R9929

R9928

SL3005

R411

R3067 R3068

R3092

R3088

IC3001

C544

LP501

R3917

TP3229 R3034 R3035

TP3231

R3037

FZ900M

TP3022

TP3129 R3023 R3024

TP3131

R3026

SL3003

SL3004

TP3024

R3012

TP3029 R3014 R3015

TP3002

R3017

SL3006

R3076 R3074

R3075

14

85

C3008

TP3005

TP3032

R3013

R3011

TP3036

L3054

C3060

R3091 R3093 C3085 C3086 R3087 R3089

C3087 C3088

R3098 R3099

R3094

R3090

C3093

R3086 C3084R3085

R3033 R3031 R3032

TP3230

TP3236

R3021 R3022

TP3130

TP3136

TP3026

TP3015

R3053

IC3050

45

C3055

R3047

24

2536

37

IC3030

24

2536

37

IC3020

IC3010

24

2536

37

TP3030

IC3051

C3059

R3052

X3051

13

C3052

EB

Q3081

R505

IC501

R3057

58

14

C3053

L3053

L3051

R624

R3401 R3402

13

112

48

13

112

48

R3055

13

112

48

C3058

R3050

C3057

Q502

R3502 R3501

R3042

R3041

R3101

R3102

EB

R3044

R3043

R623

R3054

EB

FZ900KW

R3046 R3045

R3920

R3921

R3918

R3919

R3301

R3302

R3304

R3251

R3201

JL3024

JL3036

R628

Q503

JL3042

C3003

R3202

JL3023

JL3029

R3152

JL3035

JL3113

JL3041

TP3410

R3252

R3254

JL3107

JL3110

R3151

JL3116

R3504

R3154

JL3047

JL3018

R3204

R3104

R3507

JL3048

R3404

R3407

JL3112

JL3013

R3307

JL3019

R3257

R3207

JL3030

R3157

R3107

TP3510

TP3311

TP3250

TP3150

TP3110

JL3098

JL3104

C3924

C3920 C3921

JL3060

SL3002

JL3101

JL3022

TP3210

JL3043

JL3028

CN508

19

R614

R605

R606

R607

JL3046

1

44

C3504

C3500

22

JL3049

JL3011

C3404

C3400

JL3014

JL3017

C3304

23

1

44

22

23

1

44

IC3300 IC3500IC3400

22

23

1

44

C3254

IC3250IC3100 IC3150 IC3200

C3250

22

23

JL3025

1

44

C3204

C3200

22

JL3031

JL3034

C3154

JL3037

JL3040

C3104

23

1

44

22

23

1

44

22

23

1234567891011121314

A

SL3007

R3559

EB

Q3554

SL3001

R3563

EB

R603

R604

Q3001 Q3002

EBEB

R3001

C3513

C3508

C3413

C3408

C3313

C3308

C3263

C3258

C3213

C3208

C3163

C3158

R3561

JL3045

JL3050

JL3010

JL3015

JL3016

JL3020

JL3021

JL3026JL3027

JL3032

JL3033

JL3038JL3039

LP3000

Q3553

C3556

R3562

R3558

Q3555

D3552

R3552

R3556

Q3552

C3553

Q3551

EBEB

EB

R3554

R3901

R3905

Q3251

Q3252

Q3301Q3302

Q3201Q3202 Q3401Q3402

Q3101Q3102Q3151Q3152

R3906

JL3385

JL3386

R3275

R3276

EB

R3277

JL3086

EBEBEBEBEBEBEBEBEBEBEB

C3129

JL3085

R3325

R3326

R3327

JL3052

JL3051

C3128

FZ900M

R3426

R3427

JL3053

R3425

JL3054

C3126

R3226

R3227

R3225

JL3055

JL3056

C3127

R3126

R3127

JL3058

R3125

JL3057

C3124

R3176

R3177

R3175

JL3059

JL3087

C3125

R3902

B

C

D

E

F

G

H

C3113

C3108

JL3044

FZ900KW

Q3119

Q3117

BEBE

R3186

R3185

EB

Q3116Q3118

LP3001

1-878-150-

I

11

(11)

J

HCD-FZ900KW/FZ900M

3030

Sony HCD-FZ900KW, HCD-FZ900M Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

SERVICING NOTES

DISASSEMBLY

2-1. CASE

2-2. FRONT PANEL SECTION

2-3. BACK PANEL SECTION (FZ900KW)

2-4. BACK PANEL SECTION (FZ900M)

2-5. DVD MECHANISM DECK

2-6. POWER BOARD, USB BOARD

2-7. MAIN BOARD, SPEAKER BOARD, DSP BOARD

2-8. IO-COMPONENT BOARD

2-9. TRAY

2-10. BELT

2-11. MS-203 BOARD

2-12. BASE UNIT

2-13. OPTICAL PICK-UP

TEST MODE

ELECTRICAL ADJUSTMENTS

DIAGRAMS

5-1. BLOCK DIAGRAM – RF Section –

5-2. BLOCK DIAGRAM – VIDEO Section –

5-3. BLOCK DIAGRAM – AUDIO Section –

5-4. BLOCK DIAGRAM – DSP Section –

5-5. BLOCK DIAGRAM – AMP Section –

5-6. BLOCK DIAGRAM – POWER Section –

5-7. PRINTED WIRING BOARD – MAIN Section (1/2) –