Sony DSX-A112U User Manual

4-697-415-51(1)

FM/MW/LW Digital Media Player

ЦИФРОВОЙ РЕСИВЕР

To cancel the demonstration (DEMO) display, see page 11.

For the connection/installation, see page 19.

Для отмены демонстрации на дисплее (режим DEMO) см. стр. 12.

Инструкции по установке/подключению см. на стр. 22.

Operating Instructions

Инструкция по эксплуатации

DSX-A112U

For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. For details, see “Connection/Installation” (page 19).

Made in Thailand

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.

Warning if your car’s ignition has no ACC position

Be sure to set the AUTO OFF function (page 11). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the AUTO OFF function, press and hold OFF until the display disappears each time you turn the ignition off.

Disclaimer regarding services offered by third parties

Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

2GB

Table of Contents

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . 4

Getting Started

Detaching the Front Panel. . . . . . . . . . . . . . . . . . . . 5

Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Checking the Battery Voltage . . . . . . . . . . . . . . . . . 6

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . 6

Connecting Other Portable Audio Device . . . . . . . 7

Listening to the Radio

Listening to the Radio . . . . . . . . . . . . . . . . . . . . . . . 7

Using Radio Data System (RDS) . . . . . . . . . . . . . . . 8

Playback

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . . 9

Searching and Playing Tracks . . . . . . . . . . . . . . . . 10

Settings

Canceling the DEMO Mode . . . . . . . . . . . . . . . . . . . 11

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . . 11

General Setup (GENERAL) . . . . . . . . . . . . . . . . . . . . 11

Sound Setup (SOUND) . . . . . . . . . . . . . . . . . . . . . . . 12

Display Setup (DISPLAY) . . . . . . . . . . . . . . . . . . . . . 13

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . 13

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 19

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3GB

Guide to Parts and Controls

Main unit

 Front panel release button  SRC (source)

Turn o n the p owe r. Change the source.

OFF

Press and hold for 1 second to turn the source off and display the clock. Press and hold for more than 2 seconds to turn off the power and the display.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item. Press SRC, rotate then press to change the source (timeout in 2 seconds).

Open the setup menu.

 Display window  / (SEEK –/+)

Tune in radio stations automatically. Press and hold to tune manually.

/ (prev/next) / (fast-reverse/fast-forward)

4GB

 PTY (program type)

Select PTY in RDS.

(browse) (page 10)

Enter the browse mode during playback. (Not available when a USB device in Android™ mode is connected.)

 EQ (equalizer)

Select an equalizer curve.

 (back)

Return to the previous display.

MODE (page 7)

 Receptor for the remote commander  Number buttons (1 to 6)

Receive stored radio stations. Press and hold to store stations.

ALBUM /

Skip an album for audio device. Press and hold to skip albums continuously. (Not available when a USB device in Android mode is connected.)

(repeat)

(Not available when a USB device in Android mode is connected.)

(shuffle)

(Not available when a USB device in Android mode is connected.)

 (play/pause)

 EXTRA BASS

Reinforces bass sound in synchronization with the volume level. Press to change the EXTRA BASS setting: [1], [2], [OFF].

 AUX input jack  DSPL (display)

Press to change display items.

SCRL (scroll)

Press and hold to scroll a display item.

 USB port

Getting Started

Detaching the Front Panel

You can detach the front panel of this unit to prevent theft.

1 Press and hold OFF  until the unit turns

off, press the front panel release button , then pull the panel towards you to remove.

Caution alarm

If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.

Attaching the front panel

5GB

Resetting the Unit

Before operating the unit for the first time, or after replacing the car battery or changing connections, you must reset the unit.

1 Press DSPL and (back)/MODE for

more than 2 seconds.

Note

Resetting the unit will erase the clock setting and some stored contents.

Setting the area/region

After resetting the unit, the area/region setting display appears.

1 Press ENTER while [SET AREA] is

displayed.

The area/region currently set appears.

2 Rotate the control dial to select [EUROPE]

or [RUSSIA], then press it.

3 Rotate the control dial to select [YES] or

[NO], then press it.

If the setting area/region is changed, the unit is reset, then the clock is displayed.

This setting can be configured in the general setup menu (page 11).

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK-ADJ], then press it.

The hour indication flashes.

3 Rotate the control dial to set the hour

and minute.

To move the digital indication, press / (SEEK –/+).

4 After setting the minute, press MENU.

The setup is complete and the clock starts.

To display the clock

Press DSPL.

Checking the Battery Voltage

You can check the current battery voltage. (Not available while the source is off and the clock is displayed.)

1 Press DSPL repeatedly until the battery

voltage display appears.

Connecting a USB Device

6GB

1 Turn down the volume on the unit. 2 Connect the USB device to the unit.

Connecting Other Portable Audio Device

1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect the portable audio device to the

AUX input jack (stereo mini jack) on the unit with a connecting cord (not supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the connected device to other sources

Start playback of the portable audio device at a moderate volume, and set your usual listening volume on the unit. Press MENU, then select [SOUND]  [SET AUX VOL] (page 13).

Listening to the Radio

To listen to the radio, press SRC to select [TUNER].

Storing automatically (BTM)

1 Press MODE to change the band (FM1,

FM2, FM3, MW or LW).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of frequency on the number buttons.

Tuning

1 Press MODE to change the band (FM1,

FM2, FM3, MW or LW).

2 Perform tuning.

To tune manually

Press and hold / (SEEK –/+) to locate the approximate frequency, then press /  (SEEK –/+) repeatedly to fine adjust to the desired frequency.

To tune automatically

Press / (SEEK –/+). Scanning stops when the unit receives a station.

Storing manually

1 While receiving the station that you want

to store, press and hold a number button (1 to 6) until [MEM] appears.

7GB

Receiving the stored stations

1 Select the band, then press a number

button (1 to 6).

Using Radio Data System (RDS)

Setting alternative frequencies (AF) and traffic announcement (TA)

AF continuously retunes the station to the strongest signal in a network, and TA provides current traffic information or traffic programs (TP) if received.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET AF/

TA], then press it.

3 Rotate the control dial to select [SET AF-

ON], [SET TA-ON], [SET AF/TA-ON] or [SET AF/TA-OFF], then press it.

To store RDS stations with the AF and TA setting

You can preset RDS stations along with an AF/TA setting. Set AF/TA, then store the station with BTM or manually. If you preset manually, you can also preset non-RDS stations.

To receive emergency announcements

With AF or TA on, emergency announcements will automatically interrupt the currently selected source.

To adjust the volume level during a traffic announcement

Level will be stored into memory for subsequent traffic announcements, independently from the regular volume level.

To stay with one regional program (REGIONAL)

When the AF and REGIONAL functions are on, you will not be switched to another regional station with a stronger frequency. If you leave this regional program’s reception area, set [SET REG-OFF] in [GENERAL] during FM reception (page 12). This function does not work in the UK and some other areas.

Local Link function (UK only)

This function enables you to select other local stations in the area, even if they are not stored on your number buttons. During FM reception, press a number button (1 to 6) on which a local station is stored. Within 5 seconds, press again a number button of the local station. Repeat this procedure until the local station is received.

Selecting program types (PTY)

1 Press PTY during FM reception. 2 Rotate the control dial until the desired

program type appears, then press it.

The unit starts to search for a station broadcasting the selected program type.

Typ e of programs

NEWS (News), AFFAIRS (Current Affairs), INFO

(Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARI ED (Varied), POP M (Pop Music), ROCK M (Rock Music), EASY M (M.O.R. Music), LIGHT M (Light classical), CLASSICS (Serious classical), OTHER M (Other Music), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children’s program), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary)

8GB

Setting clock time (CT)

The CT data from the RDS transmission sets the clock.

1 Set [SET CT] in [GENERAL] to [SET CT-ON]

(page 12).

Playback

Playing a USB Device

AOA (Android Open Accessory) 2.0, MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices* compliant with the USB standard can be used. Depending on the USB device, the Android mode or MSC/MTP mode can be selected on the unit. Some digital media players or Android smartphones may require setting to MTP mode.

* e.g., a USB flash drive, digital media player,

Android smartphone

Notes

 For details on the compatibility of your USB device,

visit the support site on the back cover.

 Smartphones with Android OS 4.1 or higher installed

support Android Open Accessory 2.0 (AOA 2.0). However, some smartphones may not fully support AOA 2.0 even if Android OS 4.1 or higher is installed. For details on the compatibility of your Android smartphone, visit the support site on the back cover.

 Playback of the following files is not supported.

MP3/WMA/FLAC:

 copyright-protected files  DRM (Digital Rights Management) files  Multi-channel audio files

MP3/WMA:  lossless compression files

Before making a connection, select the USB mode (Android mode or MSC/MTP mode) depending on the USB device (page 12).

1 Connect a USB device to the USB port

(page 6).

Playback starts. If a device is already connected, to start playback, press SRC to select [USB].

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

9GB

Searching and Playing Tracks

Repeat play and shuffle play

Not available when a USB device in Android mode is connected.

1 During playback, press (repeat) or

(shuffle) repeatedly to select the desired play mode.

Playback in the selected play mode may take time to start.

Available play modes differ depending on the selected sound source.

Searching a track by name (QuickBrowZer™)

Not available when a USB device in Android mode is connected.

1 During USB playback, press (browse)*

to display the list of search categories.

When the track list appears, press (back) repeatedly to display the desired search category.

* During USB playback, press (browse) for more

than 2 seconds to directly return to the beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it to confirm.

3 Repeat step 2 to search the desired track.

Playback starts.

To ex it the Quick- B row Zer m ode

Press (browse).

Searching by skipping items (Jump mode)

Not available when a USB device in Android mode is conne cted.

1 Press (browse). 2 Press  (SEEK +). 3 Rotate the control dial to select the item.

The list is jumped in steps of 10% of the total number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

10GB

Settings

Canceling the DEMO Mode

You can cancel the demonstration display which appears when the source is off and the clock is displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/play mode.

Basic Setting Operation

You can set items in the following setup categories: General setup (GENERAL), Sound setup (SOUND), Display setup (DISPLAY)

1 Press MENU. 2 Rotate the control dial to select the setup

category, then press it.

The items that can be set differ depending on the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

General Setup (GENERAL)

AREA

Specifies the area/region to use this unit: [EUROPE], [RUSSIA]. If the area/region currently set is changed, this unit is reset, then the clock is displayed. (Available only while the source is off and the clock is displayed.)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK-ADJ (clock adjust) (page 6)

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF] (page 5). (Available only while the source is off and the clock is displayed.)

BEEP

Activates the beep sound: [ON], [OFF].

AUTO OFF

Shuts off automatically after a certain time when the unit is turned off: [ON] (30 minutes), [OFF].

STEERING

Registers/resets the setting of the steering wheel remote control. (Available when connected with the connection cable (not supplied).) (Available only while the source is off and the clock is displayed.) STR CONTROL (steering control) Selects the input mode of the connected remote control. To prevent a malfunction, be sure to match the input mode with the connected remote control before use.

CUSTOM

Input mode for the steering wheel remote control.

PRESET

Input mode for the wired remote control excluding the steering wheel remote control (automatically selected when [RESET CUSTOM] is performed).

11GB

EDIT CUSTOM

Registers the functions (SOURCE, ATT, VOL +/–, SEEK +/–) to the steering wheel remote control:  Rotate the control dial to select the function

you want to assign to the steering wheel remote control, then press it.

 While [REGISTER] is blinking, press and hold

the button on the steering wheel remote control you want to assign the function to. When registration is complete, [REGISTERED] is displayed.

 To register other functions, repeat steps 

and .

(Available only when [STR CONTROL] is set to [CUSTOM].)

RESET CUSTOM

Resets the setting of the steering wheel remote control: [YES], [NO]. (Available only when [STR CONTROL] is set to [CUSTOM].)

Notes

 While making settings, only button operation on

the unit is available. For safety, park your car before making this setting.

 If an error occurs while registering, all the

previously-registered information remains. Restart registration from the function where the error occurred.

 This function may not be available on some

vehicles. For details on the compatibility of your vehicle, visit the support site on the back cover.

USB MODE

Changes the USB mode: [ANDROID], [MSC/MTP]. (Available only when the USB source is selected.)

CT (clock time)

Activates the CT function: [ON], [OFF].

AF/TA (alternative frequencies/traffic announcement)

Selects the alternative frequencies (AF) and traffic announcement (TA) setting: [AF-ON], [TAON], [AF/TA-ON], [AF/TA-OFF]. (Available when any source is selected.)

REGIONAL

Restricts reception to a specific region: [ON], [OFF]. (Available only when FM is received.)

BTM (best tuning memory) (page 7)

(Available only when the tuner is selected.)

FIRMWARE

(Available only while the source is off and the clock is displayed.) Checks/updates the firmware version. For details, visit the support site on the back cover. FW VERSION (firmware version) Displays current firmware version. FW UPDATE (firmware update) Enters firmware update process: [YES], [NO]. Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.

Sound Setup (SOUND)

This setup menu is available when any source is selected.

EQ10 PRESET

Selects an equalizer curve from 10 equalizer curves or off: [OFF], [R&B], [ROCK], [POP], [HIP-HOP], [EDM], [JAZZ], [SOUL], [COUNTRY], [KARAOKE]*, [CUSTOM]. The equalizer curve setting can be memorized for each source.

* [KARAOKE] reduces the vocal sound but cannot

be fully removed during playback. Also, using a microphone is not supported.

EQ10 CUSTOM

Sets [CUSTOM] of EQ10. Setting the equalizer curve: [BAND1] 32 Hz, [BAND2] 63 Hz, [BAND3] 125 Hz, [BAND4] 250 Hz, [BAND5] 500 Hz, [BAND6] 1 kHz, [BAND7] 2 kHz, [BAND8] 4 kHz, [BAND9] 8 kHz, [BAND10] 16 kHz. The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.

BALANCE

Adjusts the sound balance: [RIGHT-15] – [CENTER] – [LEFT-15].

12GB

FAD ER

Folder (alb um)

Audio file (track)

Adjusts the relative level: [FRONT-15] – [CENTER] – [REAR-15].

AUX VOL (AUX volume)

Adjusts the volume level for each connected auxiliary device: [+18 dB] – [0 dB] – [-8 dB]. This setting negates the need to adjust the volume level between sources. (Available only when the AUX is selected.)

Display Setup (DISPLAY)

DIMMER

Changes the display brightness: [ON], [OFF], [CLK] (clock). To set this function to be active only during a fixed period, select [CLK], then set the start and end times.

– To set the brightness when the dimmer

function is activated: Set [DIMMER] to [ON], then adjust [BRIGHTNESS].

– To set the brightness when the dimmer

function is deactivated: Set [DIMMER] to [OFF], then adjust

[BRIGHTNESS]. The brightness setting is stored and applied when the dimmer function is activated or deactivated.

BRIGHTNESS

Adjusts the display brightness. The brightness level is adjustable: [1] – [10].

SND SYNC (sound synchronization)

Activates the synchronization of the illumination with the sound: [ON], [OFF].

AUTO SCR (auto scroll)

Scrolls long items automatically: [ON], [OFF]. (Not available when the AUX or tuner is selected.)

Additional Information

Updating the Firmware

To update the firmware, visit the support site on the back cover, then follow the online instructions.

Notes

 Using a USB device (not supplied) is required for

updating the firmware. Store the updater in the USB device, and connect the device to the USB port, then perform the update operation.

 Updating the firmware takes a few minutes to

complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.

Precautions

 Cool off the unit beforehand if your car has been

parked in direct sunlight.

 Do not leave the front panel or audio devices

brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight.

 Power antenna (aerial) extends automatically.

To maintain high sound quality

Do not splash liquid onto the unit.

Playback order of audio files

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

13GB

Maintenance

Cleaning the connectors

The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 5) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged.

Notes

 For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition switch.

 Never touch the connectors directly with your fingers

or with any metal device.

Specifications

Tuner section

Tunin g ran ge:

When [AREA] is set to [EUROPE]:

87.5 MHz – 108.0 MHz When [AREA] is set to [RUSSIA]: FM1/FM2: 87.5 MHz – 108.0 MHz

(at 50 kHz step)

FM3: 65 MHz – 74 MHz (at 30 kHz step)

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

When [AREA] is set to [EUROPE]: FM CCIR: -1,956.5 kHz to -487.3 kHz and

+500.0 kHz to +2,095.4 kHz

When [AREA] is set to [RUSSIA]: FM CCIR: -1,956.5 kHz to -487.3 kHz and

+500.0 kHz to +2,095.4 kHz

FM OIRT: -1,815.6 kHz to -943.7 kHz and

+996.6 kHz to +1,776.6 kHz

Usable sensitivity: 7 dBf

Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 73 dB Separation: 50 dB at 1 kHz Frequency response: 20 Hz – 15,000 Hz

MW/LW

Tuning range:

MW: 531 kHz – 1,602 kHz LW: 153 kHz – 279 kHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Sensitivity: MW: 26 μV, LW: 50 μV

USB Player section

Interface: USB (Full-speed) Maximum current: 500 mA Maximum number of recognizable folders and files:

Folders (albums): 256 Files (tracks) per folder: 256

Compatible Android Open Accessory protocol

(AOA): 2.0

Corresponding codec:

MP3 (.mp3)

Bit rate: 8 kbps - 320 kbps (Supports VBR

(Variable Bit Rate))

Sampling rate: 16 kHz - 48 kHz

WMA (.wma)

Bit rate: 32 kbps - 192 kbps (Supports VBR

(Variable Bit Rate))

Sampling rate: 32 kHz, 44.1 kHz, 48 kHz

FLAC (.flac)

Bit depth: 16 bit, 24 bit Sampling rate: 44.1 kHz, 48 kHz

Power amplifier section

Output: Speaker outputs Speaker impedance: 4 Ω – 8 Ω Maximum power output: 55 W × 4 (at 4 Ω)

General

Outputs:

Audio outputs terminal (REAR) Power antenna (aerial)/Power amplifier control

terminal (REM OUT)

Inputs:

Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) USB port

14GB

Power requirements: 12 V DC car battery (negative

ground (earth))

Rated current consumption: 10 A Dimensions:

Approx. 178 mm × 50 mm × 119 mm

/8 in × 2 in × 4 3/4 in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 53 mm × 102 mm

/4 in × 2 1/8 in × 4 1/8 in) (w/h/d) Mass: Approx. 0.7 kg (1 lb 9 oz) Package contents:

Main unit (1) Parts for installation and connections (1 set)

Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information.

Design and specifications are subject to change without notice.

Copyrights

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

Android is a trademark of Google Inc.

libFLAC

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

 Redistributions of source code must retain the

above copyright notice, this list of conditions and the following disclaimer.

 Redistributions in binary form must reproduce

the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

 Neither the name of the Xiph.org Foundation nor

the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

15GB

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, see “Connection/Installation” (page 19). If the problem is not solved, visit the support site on the back cover.

General

No sound or the sound is very low.

 The position of the fader control [FADER] is not

set for a 2-speaker system.

 The volume of the unit and/or connected device

is very low.  Increase the volume of the unit and connected

device.

No beep sound.

 An optional power amplifier is connected and

you are not using the built-in amplifier.

The contents of the memory have been erased.

 The power supply lead or battery has been

disconnected or not connected properly.

Stored stations and correct time are erased. The fuse has blown. Makes a noise when the position of the ignition is switched.

 The leads are not matched correctly with the car’s

accessory power connector.

During playback or reception, the demonstration mode starts.

 If no operation is performed for 5 minutes with

[DEMO-ON] set, the demonstration mode starts.  Set [DEMO-OFF] (page 11).

The display disappears from/does not appear in the display window.

 The dimmer is set to [DIM-ON] (page 13).  The display disappears if you press and hold OFF.

 Press OFF on the unit until the display appears.

 The connectors are dirty (page 14).

The display/illumination flashes.

 The power supply is not sufficient.

 Check that the car battery supplies enough

power to the unit. (The power requirement is 12 V DC.)

The operation buttons do not function.

 Press DSPL and (back)/MODE for more than

2 seconds to reset the unit. The contents stored in memory are erased. For your safety, do not reset the unit while you are driving.

Radio reception

Stations cannot be received. The sound is hampered by noises.

 The connection is not correct.

 Check the connection of the car antenna

(aerial).

 If the auto antenna (aerial) will not extend,

check the connection of the power antenna (aerial) control lead.

Preset tuning is not possible.

 The broadcast signal is too weak.

65 MHz to 74 MHz in FM3 cannot be tuned in.

 [AREA] is set to [EUROPE].

 Set [AREA] to [RUSSIA] (page 11).

RDS

RDS services cannot be received (when [AREA] is set to [RUSSIA]).

 FM3 is selected.

 Select FM1 or FM2.

 RDS services are unavailable in the current

region.

The SEEK starts after a few seconds of listening.

 The station is non-TP or has weak signal.

 Deactivate TA (page 8).

No traffic announcements.

 Activate TA (page 8).  The station does not broadcast any traffic

announcements despite being TP.  Tune in another station.

16GB

+ 36 hidden pages