Sony DAV-HDX575WC, DAV-HDX578W, DAV-HDX678WF, DAV-HDX975WF Operating Instruction

3-283-033-12(1)

DVD Home Theatre System

Operating Instructions

DAV-HDX575WC / HDX578W / HDX678WF / HDX975WF

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Caution – The use of optical instruments with this product will increase eye hazard.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.

Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like.

In door use only.

For the customers in the U.S.A

The following FCC statement applies only to the version of this model manufactured for sale in the USA. Other versions may not comply with FCC technical regulations.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna (aerial).

– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to cons titute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Owner’s Record

The model and serial numbers are located at the rear exterior of the control unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. DAV-HDX575WC/DAV-HDX578W/ DAV-HDX678WF

Serial No.______________

Date of Manufacture Marking is located on the bottom exterior.

CAUTION

THIS CLASS B DIGITAL DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

For the wireless transceiver (EZW-RT10)

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Notice for the customers in Canada

For the wireless transceiver (EZW-RT10)

This class B digital apparatus complies with Canadian ICES-003.

This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired op eration of this device.

This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

Precautions

On power sources

• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (mains), even if the unit itself has been turned off.

• Install this system so that the AC power cord (mains lead) can be unplugged from the wall socket immediately in the event of trouble.

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

About This Operating

About the S-AIR function

Instructions

• The instructions in this Operating Instructions describe the controls on the remote. You can also use the controls on the unit if they have the same or similar names as those on the remote.

• The instructions in this manual are for DAVHDX575WC, DAV-HDX578W, DAVHDX678WF, and DAV-HDX975WF. DAVHDX575WC is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “DAV-HDX575WC only.”

• The Control Menu items may vary depending on the area.

• “DVD” may be used as a general term for a DVD VIDEO, DVD+RW/DVD+R, and DVDRW/DVD-R.

• Measurements are expressed in feet (ft) for North American models.

• The default setting is underlined.

The system is compatible with the S-AIR function, which allows transmission of sound between S-AIR products wirelessly. The following S-AIR products can be used with the system:

• Surround amplifier: You can enjoy surround speaker sound wirelessly.

• S-AIR receiver: You can enjoy system sound in another room.

The configuration of the S-AIR products is as follows:

• DAV-HDX575WC: Surround amplifier (optional) S-AIR receiver (supplied)

• DAV-HDX578W: Surround amplifier (supplied) S-AIR receiver (optional)

• DAV-HDX678WF: Surround amplifier (supplied) S-AIR receiver (supplied)

• DAV-HDX975WF: Surround amplifier (supplied) S-AIR receiver (supplied)

The S-AIR product can be purchased as an option (the S-AIR product lineup differs depending on the area).

Notes or instructions for the surround amplifier or S-AIR receiver in this operating instructions refer only to when the surround amplifier or S-AIR receiver is used. For details on the S-AIR function, see “Using an S-AIR Product” (page 84).

Table of Contents

About This Operating Instructions..........4

About the S-AIR function.......................4

Playable Discs......................................... 6

Getting Started

Step 1: Assembling

the Speakers ........................... 15

Step 2: Positioning the System... 21 Step 3: Connecting the System... 25 Step 4: Setting up the Wireless

System ..................................... 42

Step 5: Performing the Quick

Setup........................................ 44

Step 6: Enjoying Sound from all the

Speakers.................................. 47

Sound Adjustment

Enjoying Surround Sound by Using

Decoding Mode .............................. 49

Selecting the Sound Mode .................... 51

Enjoying Multiplex Broadcast Sound ... 52

Disc

Playing a Disc ....................................... 53

Using Play Mode...................................59

Searching/Selecting a Disc ...................61

Playing MP3 Files/JPEG Image Files... 63 Adjusting the Delay Between the Picture

and Sound .......................................66

Restricting Playback of the Disc...........67

Using the Setup Display........................69

Tuner

Presetting Radio Stations......................77

Listening to the Radio...........................78

Control for HDMI/External Audio Device

Using the Control for HDMI Function for

“BRAVIA” Sync ............................80

Using the DIGITAL MEDIA PORT

Adapter ........................................... 83

Using an S-AIR Product .......................84

Other Operations

Getting Optimal Surround Sound for a

Room .............................................. 90

Calibrating the Appropriate Settings

Automatically................................. 91

Controlling the TV with the Supplied

Remote ........................................... 92

Using the Sound Effect......................... 94

Using the Sleep Timer .......................... 94

Changing the Brightness of the Front

Panel Display.................................. 95

Viewing Information About the Disc ... 95

Returning to the Default Settings ......... 97

Additional Information

Precautions............................................ 99

Notes about the Discs ......................... 100

Troubleshooting.................................. 101

Self-diagnosis Function ...................... 109

Specifications...................................... 110

Glossary.............................................. 113

Language Code List ............................ 115

Index to Parts and Control ..................116

Guide to the Control Menu Display ... 121

Index ................................................... 124

Playable Discs

Type Disc logo Characteristics Icon

DVD VIDEO • DVD VIDEO

• DVD-R/DVD-RW in DVD VIDEO format or video mode

• DVD+R/DVD+RW in DVD VIDEO format

VR (Video Recording) mode

Super Audio CD • Super Audio CD

VIDEO CD • VIDEO CD (Ver. 1.1 and 2.0 discs)

CD • Audio CD

DATA CD – • CD-R/CD-RW/CD-ROM in

DATA DVD – • DVD-ROM/DVD-R/DVD-RW/

MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data. MP3 files

must be in MPEG1 Audio Layer 3 format.

• DVD-R/DVD-RW in VR (Video Recording) mode (except for DVD-R DL)

• Super VCD

• CD-R/CD-RW/CD-ROM in video CD format or Super VCD format

• CD-R/CD-RW in audio CD format

DATA CD format, containing MP3 files1) and JPEG image files2), and conforming to ISO 9660 Level 2, or Joliet (extended format)

DVD+R/DVD+RW in DATA DVD format, containing MP3 files1) and JPEG image files2), and conforming to UDF (Universal Disk Format)

Level 1/

JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image

standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association (JEITA).)

A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for

Standardization).

“DVD-RW,” “DVD+RW,” “DVD+R,”“DVD VIDEO,” and the “CD” logos are trademarks.

Example of discs that the system cannot play

The system cannot play the following discs:

• CD-ROM/CD-R/CD-RW other than those recorded in the formats listed on page 6

• CD-ROM recorded in PHOTO CD format

• Data part of CD-Extra

• CD Graphics disc

• DVD Audio

• DATA DVD that does not contain MP3 files or JPEG image files

• DVD-RAM

Also, the system cannot play the following discs:

• A DVD VIDEO with a different region code (page 8)

• A disc that has a non-standard shape (e.g., card, heart)

• A disc with paper or stickers on it

• A disc that has the adhesive of cellophane tape or a sticker still left on it

Note about CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW

In some c ases, CD-R/CD-RW/DVD-R /DVD-RW/DVD+R /DVD+RW cannot be played on th is system due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs/DATA DVDs created in Packet Write format cannot be played.

Music discs encoded with copyright protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Note on DualDiscs

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

About Multi Session CD

• This system can play a Multi Session CD when an MP3 file is contained in the first session. Any subsequent MP3 files recorded in later sessions can also be played back.

• This system can play a Multi Session CD when a JPEG image file is contained in the first session. Any subsequent JPEG image files recorded in later sessions can also be played back.

• If MP3 files and JPEG image files in music CD format or video CD format are recorded in the first session, only the first session will be played back.

Region code

Your system has a region code printed on the rear of the unit and will only play a DVD labeled with the same region code.

A DVD VIDEO labeled will also play on this system. If you try to play any other DVD VIDEO, the message [Playback prohibited by area limitations.] will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be given even though playing the DVD VIDEO is prohibited by area restrictions.

ALL

Note about playback operations of a DVD or VIDEO CD

Some playback operations on a DVD or VIDEO CD may be intentionally set by software producers. Since this system will play a DVD or VIDEO CD according to the disc contents the software producers designed, some playback features may not be available. Be sure to read the operating instructions supplied with the DVD or VIDEO CD.

Copyrights

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround decoder and the DTS** Digital Surround System.

* Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

** Manufactured under license from DTS, Inc.

“DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.

This system incorporates High-Definition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

“BRAVIA” and are trademarks of Sony Corporation.

“S-AIR” and its logo are trademarks of Sony Corporation.

Getting Started

Unpacking

DAV-HDX575WC

Getting Started

• Front speakers (2)

• Center speaker (1)

• Surround speakers (2)

• Subwoofer (1)

• Speaker cords (6, red/white/ green/gray/blue/purple)

• Video cord (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

• Calibration mic (1)

• Foot pads (1 set)

• Posts (2)

• Post covers (2)

• Screws (large, with washer) (4)

• Screws (small) (6)

• Wireless transceiver for the unit (1)

• DIGITAL MEDIA PORT adapter (TDM-iP10) (1)

• Operating Instructions

• Speaker and TV connections (card)

• S-AIR receiver (AIR-SA10) (1)

• AM loop antenna (aerial) (1)

• FM wire antenna (aerial) (1)

• Bases (2)

• Mounting plates (2)

• Wireless transceiver for the S-AIR receiver (AIR-SA10) (1)

• Operating Instructions of the S-AIR receiver (AIR-SA10)

DAV-HDX578W

• Front speakers (2)

Getting Started

• Center speaker (1)

• Surround speakers (2)

• Subwoofer (1)

• Speaker cords (6, red/white/ green/gray/blue/purple)

•Video cord (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

• Calibration mic (1)

• Foot pads (1 set)

•Posts (2)

• Post covers (2)

• Screws (large, with washer) (4)

• Screws (small) (6)

• Surround amplifier (1)

• Speaker cord cover (1)

• Speaker cord holder (1)

• Wireless transceivers (2)

• AM loop antenna (aerial) (1)

• FM wire antenna (aerial) (1)

• Bases (2)

• Mounting plates (2)

• DIGITAL MEDIA PORT adapter (TDM-iP10) (1)

• Operating Instructions

• Speaker and TV connections (card)

DAV-HDX678WF

• Front speakers (2)

• Center speaker (1)

• Surround speakers (2)

• Subwoofer (1)

• Video cord (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

• Calibration mic (1)

• Foot pads (1 set)

• Posts (2)

• Bases (2)

• Surround amplifier (1)

• Speaker cord cover (1)

• Speaker cord holder (1)

• Wireless transceivers for the unit (2)

• DIGITAL MEDIA PORT adapter (TDM-iP10) (1)

• Operating Instructions

• Speaker and TV connections (card)

• S-AIR receiver (AIR-SA10) (1)

Getting Started

• AM loop antenna (aerial) (1)

• FM wire antenna (aerial) (1)

• Speaker cords (6, red/white/ green/gray/blue/purple)

• Mounting plates (2)

• Post covers (2)

• Screws (large, with washer) (4)

• Screws (small) (6)

• Wireless transceiver for the S-AIR receiver (AIR-SA10) (1)

• Operating Instructions of the S-AIR receiver (AIR-SA10)

DAV-HDX975WF

• Front speakers (2) and surround speakers (2)

Getting Started

• Center speaker (1)

• Subwoofer (1)

• AM loop antenna (aerial) (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

• Calibration mic (1)

• Foot pads (1 set)

•Posts (4)

• Bases (4)

• Mounting plates (4)

• Surround amplifier (1)

• Speaker cord cover (1)

• Speaker cord holder (1)

• Wireless transceivers for the unit (2)

• DIGITAL MEDIA PORT adapter (TDM-iP10) (1)

• Operating Instructions

• Speaker and TV connections (card)

• S-AIR receiver (AIR-SA10) (1)

• FM wire antenna (aerial) (1)

• Speaker cords (6, red/white/ green/gray/blue/purple)

•Video cord (1)

• Post covers (4)

• Screws (large, with washer) (8)

• Screws (small) (12)

• Wireless transceiver for the S-AIR receiver (AIR-SA10) (1)

• Operating Instructions of the S-AIR receiver (AIR-SA10)

Attaching the foot pads to the subwoofer

Attach the foot pads (supplied) to the bottom of the subwoofer to stabilize the subwoofer and prevent it from slipping.

Remove the foot pads from the mount seat.

Using the remote

Inserting batteries into the remote

Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the markings inside the compartment.

Getting Started

Note

• Do not leave the remote in an extremely hot or humid place.

• Do not use a new battery with an old one.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

About operation of the remote

You can operate this system and TV using the supplied remote.

x System operation

Press TV so that TV flashes four times. The remote enters system operation mode. When operating the system, point the remote at the remote sensor on the unit.

x TV operation

Press TV so that TV lights up for 1 second. The remote enters the TV mode. To operate the system, point the remote at the TV. For details, see “Controlling the TV with the Supplied Remote” (page 92).

Getting Started

Note

• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.

Step 1: Assembling the Speakers

Before connecting the speakers, attach the speaker stand to the speaker. (For the front speakers of DAV-HDX575WC/DAV-HDX578W/DAV-HDX678WF, front and surround speakers of DAV-HDX975WF)

Use the parts as follows:

DAV-HDX575WC/DAV-HDX578W/DAV-HDX678WF

• Front speakers (2)

• Speaker cords (2, red/white)

•Posts (2)

• Bases (2)

• Mounting plates (2)

• Post covers (2)

• Screws (large, with washer) (4)

• Screws (small) (6)

DAV-HDX975WF

• Front and surround speakers (4)

• Speaker cords (4, red/white/blue/gray)

•Posts (4)

• Bases (4)

• Mounting plates (4)

• Post covers (4)

• Screws (large, with washer) (8)

• Screws (small) (12)

Getting Started

Although the rear layout of the front speaker is slightly different from it of the surround speaker, the way of the assembling is the same. (The illustrations in the following steps are for the front speakers as example.)

About how to connect the speaker cords to the SPEAKER jacks, see page 29.

Note

• Spread a cloth on the floor to avoid damaging the floor when you assemble the speakers.

• You can use the speaker without the speaker stand by installing it on the wall (page 21).

1 Thread the speaker cord through the hole in the base and post.

The connector and color tube of the speaker cords are the same color as the label of the jacks to be connected. Use the speaker cords as follows:

• Front speaker (L): White

• Front speaker (R): Red

• Surround speaker (L): Blue (DAV-HDX975WF only)

Getting Started

• Surround speaker (R): Gray (DAV-HDX975WF only) Be careful with the orientation of the post. Thread the speaker cord (and the speaker system cord)

into the end of the post that has two holes.

Bottom of the base

Speaker cord

2 Attach the post cover to the other end of the post.

Orient the slot toward you, attach the post cover so that the slot of the post engages with the tab of the post cover, then secure with the screw.

Post

Two holes

Top of the base

Speaker cord

Hole

Upper part of the post

Thread the speaker cord through the hole of the post cover.

Post cover

Screw (small)

3 Lay the post in the slot of the speaker, slide the post to the end of the slot, then secure

the post with the mounting plate and screws.

Select the speaker whose jack color on its rear panel matches the color tube of the speaker cord.

Getting Started

Post cover

Be careful the orientation of the post cover when placing the post.

Secure two screws (large, with washer).

Rear of the speaker

Mounting plate

4 Connect the speaker cords to the speaker.

Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3, and the speaker cord without the color tube to #.

Color tube Front speaker (L): White Front speaker (R): Red Surround speaker (L): Blue (DAV-HDX975WF only) Surround speaker (R): Gray (DAV-HDX975WF only)

Rear of the speaker

5 Attach the post to the base.

Insert the post so that the slit on the lower part of the post aligns with the projection of the base, then secure the post with the two screws.

Getting Started

Projection

Note

• Make sure that the slot on the post aligns with the projection of the base by rotating the post slightly.

6 Adjust the height of the speaker.

Loosen (but do not remove) the screws, adjust the height of the speaker, then secure the screws. Adjust the speaker of one side, then adjust another speaker by checking lines as a guide.

Note

• When adjusting the height of the speaker, grasp the speaker so that the speaker does not fall.

Base

Lines

Post

Slit

Screws (small)

Post

Loosen two screws.

Secure two screws.

7 Take up any speaker cord slack.

Take up slack in the speaker cord by pulling from the bottom of the base.

Secure the speaker cord by running it through the slot.

Adjust the length of the cord.

Fully-assembled illustration

DAV-HDX575WC/DAV-HDX578W/DAV-HDX678WF

Front speaker (L): White label

Front speaker (R): Red label

Getting Started

White

Red

DAV-HDX975WF

Front speaker (L): White label

Getting Started

Front speaker (R): Red label

Surround speaker (L): Blue label

Surround speaker (R): Gray label

White Red

Blue

Gray

Step 2: Positioning the System

For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position (A).

Place the system as illustrated below.

DAV-HDX575WC

A Front speaker (L (left)) B Front speaker (R (right)) C Center speaker D Surround speaker (L (left)) E Surround speaker (R (right)) F Subwoofer G Unit

Getting Started

* Not supplied.

DAV-HDX578W/DAV-HDX678WF

A Front speaker (L (left)) B Front speaker (R (right)) C Center speaker D Surround speaker (L (left)) E Surround speaker (R (right)) F Subwoofer G Unit H Surround amplifier

* Not supplied.

DAV-HDX975WF

A Front speaker (L (left)) B Front speaker (R (right)) C Center speaker D Surround speaker (L (left)) E Surround speaker (R (right)) F Subwoofer G Unit H Surround amplifier

Getting Started

Note

• Do not set the speakers in an inclined position.

• Do not place the speakers in locations that are:

– Extremely hot or cold

– Dusty or dirty

– Very humid

– Subject to vibrations

– Subject to direct sunlight

• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed, oiled, polished, etc.) floor, as staining or discoloration may result.

• Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.

• Do not lean or hang on the speaker, as the speaker may fall down.

• When you change the positions of the speakers, Sony recommends that you change the settings. For details, see “Getting Optimal Surround Sou nd for a Room” (page 90) and “Cal ibrating the Appropriate Settings Automatically ” (page 91).

To install the speakers on a wall

Before installing the speakers on a wall, connect the speaker cord to the speaker. Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3, and the speaker cord without the color tube to #.

Color tube Front speaker (L): White Front speaker (R): Red Center speaker: Green Surround speaker (L): Blue Surround speaker (R): Gray

1 Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.

See the illustrations below.

Hole on the back of the speaker

30 mm (1 3/16 inches)

4 mm (

/32 inch)

5 mm

(

/32 inch)

10 mm

/32 inch)

(

2 Fasten the screws to the wall.

DAV-HDX575WC/DAV-HDX578W/DAV-HDX678WF

For the center speaker

219 mm

/8 inches)

For the front speakers

217 mm

5/8

(

inches

)

Getting Started

8 to 10 mm

(

/32 to 13/32

For the surround speakers

(

/32 to 13/32

inch

8 to 10 mm

inch

)

DAV-HDX975WF

For the center speaker

8 to 10 mm

/32 to 13/32

(

inch

)

219 mm

/8 inches)

8 to 10 mm

/32 to 13/32

(

For the other speakers

(

/32 to 13/32

inch

8 to 10 mm

inch

)

217 mm (

5/8

inches

)

3 Hang the speakers on the screws.

5 mm

/32 inch)

(

10 mm

/32 inch)

(

Hole on the back of the speaker

Getting Started

Rear of the speaker

Note

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied.

• Contact a screw shop or installer regarding the wall material or screws to be used.

• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc.

Step 3: Connecting the System

See the connection diagram below, and read the additional information from 1 to 6 on the following pages.

Note

• Be sure to make connections securely to avoid hum and noise.

• When you connect another component with a volume control, turn up the volume of the other components to a level where sound is not distorted.

DAV-HDX575WC

3 DIGITAL MEDIA PORT adapter

3 Portable audio source

3 VCR, digital satellite receiver,

or PlayStation, etc.

Getting Started

2 TV

1 Front speaker (L)

1 Surround speaker (L)

5 Wireless

transceiver

1 Center speaker

5 Wireless

transceiver

S-AIR receiver

4 AM loop antenna (aerial)

4 FM wire antenna (aerial)

6 AC power cord (mains lead)

1 Subwoofer

1 Front speaker (R)

1 Surround speaker (R)

:Signal flow

DAV-HDX578W

3 DIGITAL MEDIA PORT adapter

3 Portable audio source

3 VCR, digital satellite receiver,

or PlayStation, etc.

Getting Started

1 Front speaker (L)

2 TV

5 Wireless

transceiver

1 Center speaker

Surround amplifier

1 Subwoofer

5 Wireless

transceiver

6 AC power cord (mains lead)

4 AM loop antenna (aerial)

4 FM wire antenna (aerial)

6 AC power cord (mains lead)

1 Front speaker (R)

1 Surround speaker (L)

:Signal flow

1 Surround speaker (R)

DAV-HDX678WF

3 DIGITAL MEDIA PORT adapter

3 Portable audio source

3 VCR, digital satellite receiver,

or PlayStation, etc.

Getting Started

2 TV

1 Front speaker (L)

Surround amplifier

5 Wireless

transceiver

1 Center speaker

5 Wireless

transceiver

6 AC power cord (mains lead)

1 Subwoofer

5 Wireless

transceiver

4 AM loop antenna (aerial)

4 FM wire antenna (aerial)

6 AC power cord (mains lead)

1 Front speaker (R)

S-AIR receiver

1 Surround speaker (L)

:Signal flow

1 Surround speaker (R)

DAV-HDX975WF

3 DIGITAL MEDIA PORT adapter

3 Portable audio source

3 VCR, digital satellite receiver,

or PlayStation, etc.

Getting Started

1 Front speaker (L)

2 TV

Surround

amplifier

5 Wireless

transceiver

1 Center speaker

5 Wireless

transceiver

6 AC power cord (mains lead)

4 AM loop antenna (aerial)

4 FM wire antenna (aerial)

6 AC power cord (mains lead)

1 Subwoofer

1 Front speaker (R)

5 Wireless

transceiver

S-AIR receiver

1 Surround speaker (L)

1 Surround speaker (R)

:Signal flow

1 Connecting the Speakers

The connector and color tube of the speaker cords are the same color as the label of the jacks to be connected. Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3, and the speaker cord without the color tube to #. Do not catch the speaker cord insulation in the speaker terminals.

Rear of speaker

Color tube

(+)

Getting Started

Connector

(–)

When connecting to the unit, insert the connector until it clicks.

DAV-HDX575WC

Rear panel

EZW-RT10

COMPONENT VIDEO OUT

B/CBPR/CR

VIDEO

OUT

AUDIO INYRL

To the surround speaker (L) (blue)

To the surround speaker (R) (gray)

SPEAKER

FRONT L

FRONT R

To the front speaker (R) (red)

To the front speaker (L) (white)

SUBWOOFER

DIGITAL IN

COAXIAL OPTICAL

SPEAKER

CENTER SUBWOOFER

SPEAKER

CENTER

To the center speaker (green)

To the subwoofer (purple)

SPEAKER

FRONT R FRONT L SUR R SUR L

HDMI OUT

DMPORT

DC5V

0.7A MAX

COAXIAL 75

SAT/CABLE

AUDIO INRL

ANTENNA

DAV-HDX578W/DAV-HDX678WF/DAV-HDX975WF

Rear panel of the unit

SPEAKER

CENTER SUBWOOFER

DIGITAL IN

COAXIAL OPTICAL

HDMI OUT

SPEAKER

FRONT R FRONT L

EZW-RT10

COMPONENT VIDEO OUT

B/CBPR/CR

DMPORT

DC5V

0.7A MAX

COAXIAL 75

VIDEO OUT

AUDIO INYRL

ANTENNA

SAT/CABLE

AUDIO INRL

Getting Started

SPEAKER

SUBWOOFER

CENTER

To the center speaker (green)

To the subwoofer (purple)

Rear panel of the surround amplifier

EZW-RT

S-AIR ID

SPEAKER

PAIRIN G

SURROUND SELECTOR

B C

SURROUND SURROUND

BACK

To the surround speaker (L)

(blue)

To the surround speaker (R) (gray)

SPEAKER

FRONT L

FRONT R

To the front speaker (R) (red)

To the front speaker (L) (white)

+ 98 hidden pages