The model and serial num bers are located o n the rear of the u nit. Record the ser ial number
in the space provided below. Refer to them when ev er you c all upon your Sony dealer
regarding this product.
Model No. ______________ Serial No. ______________
To prevent fire or shock hazard, do not
expose the unit to rain or moi st u r e.
To prevent fire, do not cover the ventil at ion of the
apparatus with news papers, table-cloths, curtains, etc.
And don’t place lighted candle s on the apparatus.
To prevent fire or shock hazard, do not place obje c ts
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabi ne t.
This appliance is
classified as a CLASS 1
LASER product. This
marking is locat ed on the
rear exterior.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical was te.
For customers in the United States
This symbol is intended to alert
the user to the p r esence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to consti tute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the p r esence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
The use of optical instruments wit h this prod uc t will
increase eye hazard.
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protectio n aga i nst ha r mf ul
interference in a residential installation. This
equipment generates, uses, and ca n r adia te radio
frequency energy and, if not in sta ll ed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installa tion. If this equipment doe s cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the rece iv i ng an tenna.
– Increase the separation betwe e n the equi pment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experie nc ed radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modification not
expressly approved in this manual could void your
authority to operate this equipment.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 o f th e N E C that
provides guidelines for proper ground ing a nd, in
particular, specifies that the cable ground shall be
connected to the grounding system of the buil ding, as
close to the point of cable entry as practical.
For customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
Except for European model
ENERGY STAR® is a U.S.
registered mark. As an E
®
TAR
partner, Sony Corporation
S
has determined that this produc t
meets the E
NERGY STAR
NERGY
®
guidelines for energy efficiency.
GB
2
Table of Contents
How to use this manual...........................4
Adjusting the sound............................. .18
GB
3
How to use this manual
This manual mainly explains operations using
the remote, but the same operations can also be
performed using the buttons on the system
having the same or similar names.
Playable discs
You can play back the following discs on thi s
system. Other discs cannot be played back.
List of playable discs
Discs that this system cannot
play
•CD-ROMs
• CD-Rs/CD-RWs other than those recorded in
the following formats:
– music CD format
– MP3 format that con forms to ISO9660*
Level 1/Level 2, Joliet or Multi Session**
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with pape r or stickers on it.
• A disc that has the adhesive, cellophane tape,
or a sticker still left on it.
Format of discsDisc logo
Audio CDs
CD-R/CD-RW
(audio data/MP3 files*)
*CMT-GPX7/CMT-GPX6 only
* ISO 9660 Format
The most common international standard for the
logical format of files and folders on a CD-ROM.
There are several specification le ve ls. In Level 1,
file names must be in the 8.3 for ma t ( no more than
eight character s in the name, no more th a n th r ee
characters in the extension “.MP3”) and in capital
letters. Folder name s can be no long er th an eight
characters. There can be no more than eight nested
folder levels. Level 2 specif ic a tions allow file
names and folder names up to 31 characters long.
Each folder can have up to 8 trees.
For Joliet in the expansion format (file and folder
names can have up to 64 characters) make sure of
the contents of the writing software, etc.
**Multi Session
This is a recording method that ena bles adding of
data using the Track-At-Once method.
Conventional CDs begin at a CD control area called
the Lead-in and end at an area called Lead-out. A
Multi Session CD is a CD having multiple sessions,
with each segment from Lead-in to Lead-out
regarded as a single session.
CD-Extra: This format records audio (audio CD
data) on the tracks in session 1 and data on the tracks
in session 2.
Mixed CD: This format rec or ds data on the first
track and audio (audio CD data) on the se c ond a nd
subsequent tracks of a sessio n.
GB
4
Notes on CD-R and CD-RW
• Some CD-Rs or CD - R W s cannot be played
on this system depending upon the recording
quality or physical condition of the disc, or
the characteri st ics of the recordin g device.
Furthermore, the disc will not play if it has not
been correctly finalized. For more
information, see the oper ating instructio ns for
the recordin g device.
• Discs recorded on CD-R/CD-RW drives may
not be played back because of scratches, dirt,
recording condition or the driver’s
characteristics.
• CD-R and CD-RW discs recorded in multisession that have not ended by “closing the
session” are not supported.
• The system may be unable to play MP3
format files that do not have the extension
“.MP3”.
• Attempting to play non-MP3 format files that
have the extension “.MP3” may result in noise
or malfunction.
• With formats other than ISO 9660 level 1 and
2, folder names or file names may not be
displayed co rr ectly.
• The following discs take a longer time to start
playback.
– a disc recorded with complicated tree
structure.
– a disc recorded in Multi Session.
– a disc to which data can be added (non-
finalized disc).
Music discs encoded with
copyright protection
technologies
This product is de si gned to playback discs that
conform to the Compact Disc (CD) standard.
Recently, vari ous music discs enco ded with
copyright pr ot ection tech nologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Cautions when playing a disc
that is recorded in Multi
Session
• If the disc begins with a CD-DA session, it is
recognized as a CD-DA (audio) disc, and
MP3 sessions are played back without sound.
• If the disc begins with an MP3 session, it is
recognized as an M P 3 disc, and CD-DA
sessions are played back without sound.
• The playback range of an MP3 disc is
determined by the tree structure of files
produced by analyzing of the disc.
• A disc with a mixed CD format will be
recognized as a CD-DA (audio) dis c.
GB
5
Getting Started
Hooking up the system
Perform the following procedures 1 to 4 to hook up your syste m using the supplied co rds and
accessories.
Right speaker
AM loop antenna
1
2
3
FM lead antenna
4
Left speaker
1 Connect the speakers.
Connect the rig ht and left speaker cords to
the SPEAKER terminals as shown below.
Gray (3)
3
L
#
#
Insert this portion
GB
6
Black (#)
R
3
SPEAKER
IMPEDANCE
USE 6-16
Ω
2 Connect the FM and AM antennas.
Set up the AM loop antenna, then connect
it.
Plug type A
ANTENNA
AM
FM 75
Extend the FM lead antenna horizontally
AM loop
antenna
Plug type B
ANTENNA
AM
FM 75
Extend the FM lead antenna horizontally
Plug type C
ANTENNA
AM
AM loop
antenna
AM loop
antenna
4 Connect the power cord to a wall
outlet.
If the plug does not fit the wall socket,
detach the supp l ie d plug adaptor (onl y for
models equipped w i th an adaptor).
To turn on the system, press ?/1.
Inserting two R6 (size AA)
batteries into the remote
Getting Started
FM 75
North American models:
Connect using the white side
Other models:
Connect using the brown side
Note
To prevent noise pickup, keep the antennas away from
the system and other components.
Extend the FM lead
antenna horizontally
3 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage. The voltage
selector is located at the bottom of the
apparatus.
Refer to the print on y o ur system ’s
VOLTAGE SELECTOR for available
settings.
230-240V
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage and corros ion .
Tip
When the remote no longer operates the system,
replace both batteries with new ones.
GB
7
Setting the clock
Use buttons on the r emote for the operati on.
1 Press ?/1 to turn on the system.
2 Press CLOCK/TIMER SET.
3 Press ./> repeatedly to set the
hour.
4 Press ENTER.
5 Press ./> repeatedly to set the
minute.
6 Press ENTER.
The clock starts working.
To adjust the clock
1 Press CLOCK/TIMER SET.
2 Press ./> until “CLOCK SET”
appears, then press ENTER.
3 Do the same procedures as step 3 to 6
above.
Note
The clock is not displayed in Power Saving Mode
(page 21).
CD/MP3 – Play
Loading a disc
1 Press CD (or FUNCTION repeatedly on
the unit) to switch the function to CD.
2 Insert a disc in the disc slot with the
label side up.
When you
play a disc,
insert it with
the label side
up.
Notes
• When you turn on the system, the disc is not
pulled into the disc slot until “NO DISC”
appears in the display. Do not attempt to
push in the disc until “NO DISC” appears.
• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
• Do not use a non-standard shape disc.
• Do not load an 8 cm disc with an adaptor. Doing so
may cause the system to mal f u nction.
• When you eject a disc, handle the disc by its edge. Do
not touch the surface.
• If you load a disc that is not playable by this system,
it will be ejected au tomatically.
.
mM
Z
x
X
N
>
GB
8
Playing a disc
— Normal Play/Shuffle Play
You can play audio CDs and discs with MP3
audio tracks.
MP3 audio tracks cann ot be played on CMTGPX5.
Track number
Playing time
1 Press CD (or FUNCTION repeatedly on
the unit) to switch the function to CD.
2 Press PLAY MODE in stop mode
repeatedly until the mode you want
appears.
SelectTo play
No display
(Normal Play)
ALBM
(Normal Play)
SHUF
(Shuffle Play)
ALBM SHUF
(Shuffle Play)
PGM
(Program Play)
The tracks on the disc in
original order.
All MP3 audio tracks in the
album on the disc in original
order.
When playing a non-MP3
disc, Album Play performs
the same operation as
Normal Play.
All tracks on the disc in
random order.
All MP3 audio tracks in the
album on the disc in random
order.
When playing a non-MP3
disc, Album Shuffle Play
performs the same operation
as Shuffle Play.
The tracks on the di sc in the
order you want them to be
played (see “Creating your
own program” on page 11).
3 Press N (or CD/NX on the unit).
Other operations
ToDo this
Stop playPress x (CD stop).
PausePress X (or CD/NX on the unit).
Select a trackPress
Select an album
of MP3
Find a point in a
track
Remove a discPress A on the unit.
Notes
• You cannot change the play mode during playback.
• Some time may be needed to start playback of discs
recorded in complex configurations such as many
layers.
• Whe n the d is c is in serted, the player reads all th e
audio tracks on that disc . If there are many album s or
non-MP3 audio tracks on the disc, it may take a long
time for play to begin or for the next MP3 audio track
to start play.
• Do not save unnecessary albums or audio tracks
other than MP3 ones in the disc to be used fo r MP3
listening. We recommend that you do not save other
types of audio tracks or unnecessary albums on a disc
that has MP3 audio tracks.
• An album that does not include an MP3 audio track
is skipped.
• Maximum album number: 150 (including root album
and empty albums)
• The maximum number of MP3 audio tracks and
albums that can be contained on a single disc is 300.
• Playback is possible up to 8 trees.
• MP3 audio tracks are played back in the order that
they are recorded on the disc.
• Depending on the encoding/writing software,
recording device or the recording media used at the
time an MP3 audio track is recorded, you may
encounter such problems as disabled playback,
sound interruptions and noise.
• When playing back an MP3 audio track, the playback
elapsed time indication may differ from the actual
time in the follow ing cases.
– When you play back a VBR (variable bit rate)
MP3 audio track
– When you perform Fast Forward or Rewind
(Manual Search)
Press again to resume play.
./> (or .m/
M> on the unit except for
CMT-GPX5) repeatedly.
Press ALBUM +/– repeatedly
after step 2 .
Keep pressing m/M during
playback and release it at the
desired point.
CD/MP3 – Play
continued
GB
9
Tip
When disc access takes a long time, set “CD POWER”
and “ON” by CD power manage function (page 13).
Playing repeatedly
— Repeat Play
You can pl ay a ll th e tr ac ks o r a si ng le t ra ck o n a
disc repeatedly.
MP3 audio tracks cannot be played on CMTGPX5.
Press REPEAT repeatedly during playback
until “REP” or “REP 1” appears.
REP: For all tracks (depending on th e selected
play mode) up to five times or endl essly for MP3
tracks when “SHUF” is displayed.
REP 1: For a single track only.
To cancel Repeat Play
Press REPEAT repeatedly until both “ REP” and
“REP 1” disappear .
Note
When you select “REP 1”, that track is repeated
endlessly until “REP 1” is canceled.
10
GB
Creating your own
program
— Program Play
You can make a program of up to 25 steps.
You can synchro record the program ed tracks
onto a cassett e t ape (page 16).
MP3 audio tracks cann ot be played on CMTGPX5.
1 Press CD (or FUNCTION repeatedly on
the unit) to switch the function to CD.
2 Press PLAY MODE in stop mode
repeatedly until “PGM” appears.
3 Press ./> (or .m/M>
on the unit except for CMT-GPX5)
repeatedly until the desired track
number appears.
When programing an MP3, press ALBUM
+/– repeatedly to select the album, then
press ./> (or .m/M> on
the unit except for CMT-GPX5) repeatedly
until the desired track number appear s.
Other operations
ToDo this
Cancel Program
Play
Erase the program Press CLEAR in step 4.
Add a track to the
end of the program
Tips
• The program you made remains after Program Play
finishes. To play the same program again, press N
(or CD/NX on the unit). H ow e ve r, the pr ogr a m is
cleared when you eject th e d i sc.
• “– –.– –” appears if the total program time exceeds
100 minutes, if you select a track whose number is 21
or over, or when you programed an MP3 audio track.
• If you select “AL” in step 3, you can select all tracks
on the disc at once. If you select an album in step 3,
you can select all MP3 audio tracks in the album at
once.
Press PLAY MO DE in stop
mode repeatedly until both
“PGM” and “SHUF” disappears.
Each time you press the button, a
track is cleared from the end of
the program.
Perform steps 3 and 4 in stop
mode.
CD/MP3 – Play
Selected track numberTotal playing time
4 Press ENTER.
The track is programed.
The program step number appears,
followed by the last programed trac k
number.
5 To program additional tracks, repeat
steps 3 and 4.
6 Press N (or CD/NX on the unit).
Program Play starts.
11
GB
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.