e Vehicle Company
Published by Sony Engineering Corporation
1
Page 2
CDX-CA600/CA600X
k
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
• CDX-CA600/CA600X: AEP, UK model
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up bloc
semi-fixed resistor
This label is located on the bottom of the chassis.
This label is located on the drive unit’s internal chassis.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
NOTES ON CD-R/CD-RW DISCS
• Y ou can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
• Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
• You cannot play a CD-R/CD-RW that is not finalized∗.
∗ A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
Page 3
TABLE OF CONTENTS
CDX-CA600/CA600X
1. GENERAL
Location of controls
(CDX-CA600/CA600X: AEP, UK model) .............................. 4
Location of controls (CDX-CA600X: E model) .....................4
Connections (CDX-CA600/CA600X: AEP, UK model) ......... 5
Connections (CDX-CA600X: E model)..................................6
2. DISASSEMBLY
2-1. Panel (1) Assy, Sub ............................................................. 7
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 8
4-2. Front panel Section ........................................................... 29
4-3. CD Mechanism Section (1) ............................................... 30
4-4. CD Mechanism Section (2) ............................................... 31
4-5. CD Mechanism Section (3) ............................................... 32
5. ELECTRICAL PARTS LIST ........................................ 33
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP701) and the SER VO board (CN1)
with the extension cable (Part No. J-2502-062-1).
MAIN BOARD CNP701
SERVO BOARD CN1
3
Page 4
CDX-CA600/CA600X
SECTION 1
GENERAL
(CDX-CA600/CA600X: AEP, UK model)(CDX-CA600X: E model)
This section is extracted
from instruction manual.
(CDX-CA600/CA600X: AEP, UK model)(CDX-CA600X: E model)
4
Page 5
Connections (CDX-CA600/CA600X: AEP, UK model)
CDX-CA600/CA600X
5
Page 6
CDX-CA600/CA600X
Connections (CDX-CA600X: E model)
6
Page 7
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-5.CHASSIS (T) SUB ASSY
2-1.PANEL (1) ASSY, SUB
(Page 7)
(Page 9)
CDX-CA600/CA600X
2-2.CD MECHANISM BLOCK
(Page 8)
2-3.MAIN BOARD
(Page 8)
2-4.HEAT SINK
(Page 9)
2-6.LEVER SECTION
(Page 10)
2-8.SHAFT ROLLER ASSY
(Page 11)
2-9.FLOATING BLOCK ASSY
(Page 11)
2-10.OPTICAL PICK-UP BLOCK
(Page 12)
Note : Follow the disassembly procedure in the numerical order given.
2-1. PANEL (1) ASSY, SUB
2-7.SERVO BOARD
(Page 10)
1
PTT 2.6x6
2
PTT 2.6x6
3
claw
claws
5
panel (1) assy, sub
4
claws
7
Page 8
CDX-CA600/CA600X
8
6
2-2. CD MECHANISM BLOCK
5
CD mechanism block
2
PTT 2.6x6
3
7
bracket (CD)
6
PTT 2.6x
2-3. MAIN BOARD
4
screws (+BTT)
5
MAIN board
3
screw (+BTT)
4
CNP701
2
1
PTT 2.6x6
PTT 2.6x
1
PTT 2.6x8
8
Page 9
8
2-4. HEAT SINK
CDX-CA600/CA600X
6
heat sink
5
PTT 2.6x
4
PTT 2.6x8
3
PTT 2.6x12
2-5. CHASSIS (T) SUB ASSY
1
Unsolder the
lead wires.
2
P 2x3
1
PTT 2.6x8
2
PTT 2.6x8
3
P 2x3
4
chassis (T) sub assy
black
red
white
9
Page 10
CDX-CA600/CA600X
k
2-6. LEVER SECTION
6
lever (R)
3
tension spring (LR)
7
lever (L)
5
guide (disc)
1
special screw
2
IN SELF SW board
2-7. SERVO BOARD
2
4
loading motor assy
4
claws
5
special screws
Removal the solders.
1
CN3
3
P 2x3
7
SERVO board
6
special screw
8
connector
10
optical pick-up bloc
Page 11
Fig. 1
1
tension spring (RA)
2
arm (roller)
3
retaing ring (RA)
4
shaft retainer
5
shaft roller assy
retaing ring (RA)
arm
arm
washer
washer
shaft retainer
shaft retainer
2-8. SHAFT ROLLER ASSY
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
CDX-CA600/CA600X
2-9. FLOATING BLOCK ASSY
7
5
direction of the arrow.
compression spring (FL)
1
tension spring (KF1)
Turn loading ring in the
6
floating block assy
8
compression spring (FL)
4
Fit lever (D) in the
direction of the arrow.
3
damper (T)
2
damper (T)
11
Page 12
CDX-CA600/CA600X
2-10. OPTICAL PICK-UP BLOCK
1
P 2x3
2
sled motor assy
6
shaft (feed) assy
4
P 2x3
5
spring (feed), plate
3
optical pick-up block
12
Page 13
CDX-CA600/CA600X
SECTION 3
DIAGRAMS
3-1. IC PIN DESCRIPTION
• IC801 MN101C49KCF (SYSTEM CONTROL)
Pin No.Pin NameI/OPin Description
1VREF–—Ground for A/D converter power supply
2VSMIS-meter voltage detection signal input from tuner unit (TU601)
3NCIConnect to ground.
4KEYIN1IKey signal input
5KEYIN0IKey signal input
6RC IN0IRotary commander key signal input from remote in jack (CNP801)
7QUALITYINoise detection signal input from RDS decoder (IC601)
8MPTHIMultipass detection signal input
9FUNCSELIDestination set up detection signal input (“L”: CDX-CA600X, “H”: CDX-CA600)
10VREF—A/D converter power supply
11VDD—Power supply (+5 V) input pin
12OSCOUTOHigh speed clock signal output (18.432 MHz)
13OSCINIHigh speed clock signal input (18.432 MHz)
14VSS—Ground for power supply
15XINILow speed clock signal input (32.768 kHz)
16XOUTOLow speed clock signal output (32.768 kHz)
17MMODI
18LCDSOOLCD serial data signal output to LCD driver (IC501)
19LCDCEOLCD chip enable signal output to LCD driver (IC501)
20LCDCKOOLCD serial clock signal output to LCD driver (IC501)
21CD TSOOCD servo IC serial data signal output
22CD TSIICD servo IC serial data signal input
23CD TCKOOCD servo IC serial clock signal output
24SYSRSTOSystem reset signal output to bus interface (IC803)
25BUS ONOBus on signal output to bus interface (IC803)
26KEYACKIKey acknowledge detection signal input
27DAVNIRDS data block sync detection signal input
28BU INIBack up power supply detection signal input
29SIRCSIRemote signal input from remote control receiver (IC552)
30CD SELFSWICD mechanism self load position detection switch signal input from self switch (SW2)
31CD PACKICD text pack sync signal input from CD servo (IC1)
32NIHIConnect to power supply.
33RESETImicrocomputer reset signal input from reset IC (IC802) “L”: reset
34NOSESWIConnect to power supply.
35BEEPOBeep signal output to power amp (IC401)
36NCOONot used. (Open)
37TESTINITest mode detection signal input
38ACCINIAccessory power supply detection signal input
39NCOONot used. (Open)
40TELATTITelephone ATT detection signal input
41NIHIConnect to power supply.
42BUSSOOSony-Bus serial data signal output to bus interface (IC803)
43BUSSIISony-Bus serial data signal input from bus interface (IC803)
44BUSCKOOSony-Bus serial clock signal output to bus interface (IC803)
45I2CSIOI/OI2C bus serial data signal input/output
46NCOONot used. (Open)
47I2CCKOOI2C bus serial clock signal output
48NCONot used. (Open)
49TUNONOTuner power supply control signal output
50PW ONOSystem power supply control signal output
Memory mode select signal input (Input to “Low” (single chip mode).)
(Connect to ground.)
13
Page 14
CDX-CA600/CA600X
Pin No.Pin NameI/OPin Description
51TSTBOCD text parameter strob signal output to servo IC (IC1)
52RFOKIRF OK signal input from servo IC (IC1)
53CD RSTOReset signal output to servo IC (IC1)
54A0O
55STBOData strob signal output to servo IC (IC1)
56X ENOCrystal oscillation control signal output to servo IC (IC1)
57LIMITICD Mechanism in-limit switch signal input from limit switch (SW4)
58PH1ICD Mechanism PH1 detection signal input Not used in this set.
59D SWICD Mechanism down switch signal input from down switch (SW1)
60INSW/PH2ICD Mechanism disc-in switch detection signal input from disc-in switch (SW3)
61PH3ICD Mechanism PH3 detection signal input Not used in this set.
62CD LM LOOCD Mechanism loading motor control signal output to loading motor drive (IC2)
63CD LM EJOCD Mechanism eject motor control signal output to loading motor drive (IC2)
64, 65NCONot used. (Open)
66AMPATTOPower amp ATT control signal output to power amp (IC401)
67AMPONOPower amp standby control signal output to power amp (IC401)
68CDMD ONOCD mechanism deck power supply control signal output
69ATTOSystem ATT control signal output
70VOLATTOElectrical volume ATT control signal output to electrical volume (IC402)
71 – 75NCONot used. (Open)
76NCINot used. (Open)
77COL SELIColor select switch signal input “H”: Green, “L”: Amber
78NCONot used. (Open)
79XCD ONOCD on signal output “H”: Play, “L”: Loading or standby
80 – 85NCONot used. (Open)
86EE SIOI/OEEPROM serial data signal input/output
87EE CKOOEEPROM serial clock signal output
88NCONot used. (Open)
89FLASH WIFlash microcomputer write detection signal input “L”: Write mode
90NS MASKONoise mask signal output
91AD ONOKey power supply control signal output
92DOORINDOSub panel power supply control signal output Not used in this set. (Open)
93ILLONOIllumination power supply control signal output
94NOSE SWIFront panel with/without detection signal input “L”: Panel with, “H”: Panel without
95DAVSS—Ground pin
96RE IN1IRotary encoder signal input Not used in this set. (Open)
97RE IN0IRotary encoder signal input Not used in this set. (Open)
98RC IN1I
99NCONot used. (Open)
100DAVDD—Power supply pin (+5 V)
Command/parameter identification signal output to servo IC (IC1)
“L”: Command, “H”: Parameter
Rotary commander shift key signal input from remote in jack (CNP801)
“L”: Shift key on
14
Page 15
3-2. BLOCK DIAGRAM — CD SECTION —
OPTICAL PICK-UP
KSS-720A
RF AMP,DIGITAL SERVO
DIGITAL SIGNAL PROCESSOR
IC1
CDX-CA600/CA600X
PD
LD
A
C
B
D
E
F
FOCUS
COIL
I-V
CONV.
LD
DRIVE
Q1
B
84
D
85
A
82
C
83
E
87
F
86
PD
97
A+5V
LD
98
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
FCS-
15
FCS+
16
APC
IC2
FOCUS
COIL
DRIVE
TRACKING
ERROR
(Page 16)
TUNER
LOUT
RF
EQ
FORCUS
ERROR
FD
26
EFM
DEMOD
SERVO
CTL
FDTDSD
62 63 64 65
MD
D/A
CONV
DSUB CODE
PROCESS
I/F
OSC
2324
X1
16.9344MHz
ROUT
PACK
TSTB
TSCK
TSI
SCK
STB
RST
RFOK
XTALEN
16
12
R-CH
52
56
55
54
SI
8
SO
7
6
5
AO
4
3
2
9
SW1
(DOWN)
CDL
SECTION
A
SYSTEM CONTROL
31
CD_PACK
51
TSTB
21
CD_TSO
22
CD TSI
23
CD TCKO
55
STB
54
AO
53
CD_RST
52
RFOK
XEN
56
59
D SW
IC801(1/3)
TRACKING
COIL
M902
(SLED)
M901
(SPINDLE)
M903
(LOADING)
30
CD_SELFSW
INSW/PH2
60
57
LIMIT
CD_LM _LO
62
63
CD_LM_ EJ
68
CDMD ON
79
XCD ON
RESET
IC802
33
2
S801
(RESET)
RESET
1
BU+5V
• Signal path
:CD
• R-ch is omitted due to
same as L-ch.
(DISC IN)
CDMD ON
SWITCH
Q913,914
BATT
SW2
(SELF)
SW3
SW4
(LIMIT)
CD ON
SWITCH
Q915
TRK+
17
TRK-
18
SL-
M
13
SL+
14
SP+
M
11
SP-
12
LD-
M
9
LD+
10
TRACKING
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
LOADING
MOTOR
DRIVE
TD
23
SD
5
MD
6
LOAD
1
EJECT
2
A+5V
AU+5V
D+5V
DR+6V
CD+5V
REG
Q916,D927
CD DRIVE+6V
REG
Q912,D926
D925
1515
Page 16
CDX-CA600/CA600X
A
3-3. BLOCK DIAGRAM — TUNER SECTION —
PJ401
L
-1
BUS AUDIO IN
R-CH
R-CH
ELECTRONIC VOLUME
IC402
AUX L
3
CDRR-CH
CD R
2
OUT LF
30
POWER AMP
12
IC401
R-CH
5
3
-2
-5
-6
-3
-4
CNP901
R
L
R
L
R
1
FL+
9
FL-
AUDIO OUT FRONT
AUDIO OUT REAR
PJ601
(ANTENNA)
TUNER UNIT
TU601
ANTFMMPX
210
AM DET
ANTAM
1
S-METER
I2C SDA
I2C SCL
E2PROM SDA
E2PROM SCL
RDS DET
CD
LVIN
SDA
SCL
MPTH
DAVN
CDL
CA600X
BU+5V
CA600
20
9
10
2
8
(Page 15)
8
NOISE AMP
Q601
X601
IC602
16
MPX
OSCD
4
OSCI
5
BUFFER
14
12
13
17
18
9
4.332MHz
SECTION
NOISE
SUPPRESSOR
D601
MS MASK
SWITCH
Q602
RDS DECODER
IC601
CD L
1
MPX
13
AM
11
LEVEL
14
MPIN
15
SDA
20
SCL
21
MUTE
18
QUAL
17
SYSTEM CONTROL
QUALITY
7
VOL ATT
70
MS MASK
90
VSM
2
I2C SIO
45
I2C CKO
47
FUNCSEL
9
EE SIO
86
EE CKO
87
8
MPTH
27
DAVN
IC801 (2/3)
AMP ATT
OUT LR
OUT RF
OUT RR
ATT
BEEP
AMP ON
TEL ATT
ACC IN
TEST IN
TUN ON
PW ON
SYSRST
BUSON
BUSSI
BUSCKO
BUSSO
BU IN
29
Q402
MUTE
28
27
69
35
67
66
40
38
37
49
50
24
25
43
44
42
28
TUNER
+8V
TUNER
+5V
R-CH
Q911,D918,919
13
12
11
10
TUNER +5V
REG
BUS INTERFACE
RST
BUSON
DATA OUT
8
CLK IN
DATA IN
9
B/U-C
IC803
BUSON
DATA I/O
CLK
RST
BATT
TUNER ON
SWITCH
Q909,910
1
6
4
2
3
LINE MUTE
Q904,905
+8V
SWITCH
BATT DET
Q801,D801,802
Q401
MUTE
R-CH
D921,922
DELAYBATT
+5V REG
Q93,D916
+8V REG
Q906,D917
POWER ON
CONTROL
Q907,908
CNJ801
BUS
CONTROL IN
8
6
5
4
7
BATT
BATT
3
2
1
BATT+5V
BATT
ACC
DETECT
Q902, D914
BATT
11
16
4
22
AMP B+
SWITCH
Q920
AMP B+
CONTROL
SWITCH
Q921
AUX
STBY
MUTE
TEL
ATT
Q901
9
7
AMP B+
SWITCH
Q922
AMP B+
CONTROL
SWITCH
Q917
R-CH
BATT
F901
10A
2
RL+
10
RL-
4
FR+
12
FR-
3
RR+
11
RR-
13
ATT
7
ACC
15
TEST
5
AMP R
6
ANT R
8
GND
19
17
18
+B (BATT)
16
• Signal path
:FM
:MW/LW
:CD
• R-ch is omitted due to same as L-ch.
1616
Page 17
CDX-CA600/CA600X
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL
IC801 (3/3)
KEY IN0
KEY MATRIX
S501-521
CNP801
(REMOTE IN)
D809
D807
KEY
ACTIVE
Q803
IC552
REMOTE
RECEIVE
5
26
91
98
6
29
KEY IN1
KEY ACK
AD ON
RC IN1
RC IN0
SIRCS
LCD SO
LCD CKO
LCD CE
3-5. CIRCUIT BOARDS LOCATION
LCD DRIVE
IC501
2
S2
I
DATA
18
20
194
DATA
64
CLK
CLK
63
CE
CE
62
S25
S27
S38
S40
S47
COM1
|
COM4
P1/S1
INH
I
25
•
•
27
|
|
38
•
•
40
I
I
47
52
|
55
1
61
CA600
BATT
CA600
LED
DRIVE
Q502
LCD
LCD501
LED DRIVE
SWITCH
Q503
CA600X
ILL+5V
D561-589
()
ILLUMINATION
ILL+5V
LED
DRIVE
Q501
D531-559
KEY
()
ILLUMINATION
KEY
IN SELF SW board
DISPLAY board
SERVO board
SPEAKER board
tuner unit
(TU601)
MAIN board
SL SW board
X802
32.768kHz
ILL ON
XIN
15
XOUT
16
OSC OUT
OSC IN
ILL ON
SWITCH
93
12
13
Q919
BATT
X801
18.432MHz
ILL B+
REG
Q918
ILL+5V
LED549,550
LCD BACK
()
LIGHT
• Waveforms
— Servo Board —
(MODE: CD PLAY)
1
16.9344MHz
wd
(XTAL)
IC1
2
3.2msec
IC1
(PACK)
ts
3
uj
(RFO)
IC1
2Vp-p
5Vp-p
1.2Vp-p
— Main Board —
1
4.332MHz
IC601
(OSCD)
4
2
18.432MHz
IC801
(OSCOUT)
qs
3
32.768kHz
IC801
(XOUT)
qh
5.2Vp-p
2.2Vp-p
5Vp-p
4
1717
5
Approx. 100mVp-p
IC1
IC1
(FEO)
oa
Approx. 100mVp-p
(TEO)
od
0V
0V
Page 18
CDX-CA600/CA600X
3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 17 for Circuit Boards Location.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
•%: indicates tolerance.
f
•
• C : panel designation.
Note: The components identified by mark 0 or dotted line
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
• Voltages are taken with a VOM (Input impedance 10 MΩ).
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
: internal component.
with mark 0 are critical for safety.
Replace only with part number specified.
supply from ACC and BATT cords.
Voltage variations may be noted due to normal produc-
tion tolerances.
Voltage variations may be noted due to normal production tolerances.
F: FM
f: MW/LW
J: CD
4
W or less unless otherwise
CN2
23456789101112
1
A
B
C
D
E
for printed wiring boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•x: parts mounted on the conductor side.
a
•
•: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)parts face are indicated.
: Through hole.
(The other layer’s patterns are not indicated.)
F
G
H
SW1
I
J
1818
Page 19
CDX-CA600/CA600X
A
B
C
D
E
F
G
H
I
1
234567891011121314
• Semiconductor
Location
Ref. No.Location
IC1E-7
IC2H-7
Q1C-6
SW4
TP66
TP73
TP53
TP64
TP86
TP87
TP75
TP47
TP69
TP57
R20
R22
FB6
R21
TP68
TP54
TP76
FB7
FB3
TP48
TP85
TP50
TP51
TP52
TP56
TP58
TP61
TP74
TP62
CN1
TP49
TP7
C44
TP91
TP90
TP19
CN3
TP63
TP60
TP59
TP71
R17
TP72
TP80
TP8
R19
C26
TP77
R26
C4
TP9
TP70
C40
TP55
C27
C37
TP78
Q1
C6
FB1
TP20
R30
R3
C25
C34
C1
C3
R18
C41
C45
X1
TP92
TP17
R29
C29
R7
R6
TP16
TP79
C17
C22
C21
C5
C43
C9
C16
C36
TP34
TP11
TP36
C10
C8
TP35
R24
R25
TP12
FB4
FB2
C15
IC1
TP46
C38
TP39
IC2
TP82
TP81
C11
C14
TP45
TP37
TP38
TP40
TP30
TP83
TP43
TP42
TP32
R15
R12
R10
TP26
C30
TP28
TP27
TP84
C13
C18
TP23
C35
TP41
TP29
R5
R9
TP44
TP21
TP10
TP89
TP88
TP18
TP2
TP1
C20
C19
R8
R14
TP3
C23
C24
TP22
TP24
TP25
TP6
SW3
(Page 21)
SW2
TP5
TP4
J
1919
Page 20
CDX-CA600/CA600X
• Refer to page 17 for Waveforms.
3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 26 for IC Block Diagrams.
D5068-719-988-61 DIODE 1SS355TE-17 (CA600)
D5318-719-077-34 LED SML-310YTT86 (OFF) (CA600)
D5328-719-077-34 LED SML-310YTT86 (TA) (CA600)
D5338-719-077-34 LED SML-310YTT86 (SENS/BTM) (CA600)
D5348-719-053-08 LED SML-310DTT86 (SEEK4) (CA600)
D5358-719-053-08 LED SML-310DTT86 (SEEK5) (CA600)
D5368-719-077-34 LED SML-310YTT86 (Z) (CA600)
D5378-719-053-08 LED SML-310DTT86 (SEEK3) (CA600)
D5388-719-053-08 LED SML-310DTT86 (D-BASS) (CA600)
D5398-719-053-08 LED SML-310DTT86 (SEEK1) (CA600)
D5408-719-053-08 LED SML-310DTT86 (SEEK2) (CA600)
D5418-719-053-08 LED SML-310DTT86 (LIST/PTY) (CA600)
D5428-719-053-08 LED SML-310DTT86 (MBP) (CA600)
D5438-719-077-34 LED SML-310YTT86 (6) (CA600)
D5448-719-077-34 LED SML-310YTT86 (5) (CA600)
D5458-719-077-34 LED SML-310YTT86 (4/SHUF) (CA600)
D5468-719-077-34 LED SML-310YTT86 (3/REP) (CA600)
D5478-719-077-34 LED SML-310YTT86 (2/DISC +) (CA600)
D5488-719-077-34 LED SML-310YTT86 (1/DISC –) (CA600)
D5498-719-077-34 LED SML-310YTT86 (ATT) (CA600)
D5508-719-077-34 LED SML-310YTT86 (AF) (CA600)
D5518-719-053-08 LED SML-310DTT86 (DSPL) (CA600)
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
D5528-719-053-08 LED SML-310DTT86 (VOL2) (CA600)
D5538-719-053-08 LED SML-310DTT86 (VOL1) (CA600)
D5548-719-077-34 LED SML-310YTT86 (MODE) (CA600)
D5558-719-053-08 LED SML-310DTT86 (SOURCE) (CA600)
D5568-719-053-08 LED SML-310DTT86 (VOL5) (CA600)
D5578-719-053-08 LED SML-310DTT86 (SEL) (CA600)
D5588-719-053-08 LED SML-310DTT86 (VOL4) (CA600)
D5598-719-053-08 LED SML-310DTT86 (VOL3) (CA600)
D5618-719-038-05 LED CL-190FG-CD-T (OFF) (CA600)
D5618-719-053-09 LED SML-310VTT86 (OFF) (CA600X)
D5628-719-038-05 LED CL-190FG-CD-T (TA) (CA600)
D5628-719-053-09 LED SML-310VTT86 (TA) (CA600X)
D5638-719-038-05 LED CL-190FG-CD-T (SENS/BTM) (CA600)
D5638-719-053-09 LED SML-310VTT86 (SENS/BTM) (CA600X)
D5648-719-053-09 LED SML-310VTT86 (SEEK4) (CA600X)
D5648-719-078-21 LED SML-310PTT86 (SEEK4) (CA600)
D5658-719-053-09 LED SML-310VTT86 (SEEK5) (CA600X)
D5658-719-078-21 LED SML-310PTT86 (SEEK5) (CA600)
D5668-719-038-05 LED CL-190FG-CD-T (Z) (CA600)
D5668-719-053-09 LED SML-310VTT86 (Z) (CA600X)
D5678-719-053-09 LED SML-310VTT86 (SEEK3) (CA600X)
D5678-719-078-21 LED SML-310PTT86 (SEEK3) (CA600)
D5688-719-053-09 LED SML-310VTT86 (D-BASS) (CA600X)
D5688-719-078-21 LED SML-310PTT86 (D-BASS) (CA600)
D5698-719-053-09 LED SML-310VTT86 (SEEK1) (CA600X)
D5698-719-078-21 LED SML-310PTT86 (SEEK1) (CA600)
D5708-719-053-09 LED SML-310VTT86 (SEEK2) (CA600X)
D5708-719-078-21 LED SML-310PTT86 (SEEK2) (CA600)
D5718-719-053-09 LED SML-310VTT86 (LIST/PTY) (CA600X)
D5718-719-078-21 LED SML-310PTT86 (LIST/PTY) (CA600)
D5728-719-053-09 LED SML-310VTT86 (MBP) (CA600X)
D5728-719-078-21 LED SML-310PTT86 (MBP) (CA600)
D5738-719-038-05 LED CL-190FG-CD-T (6) (CA600)
D5738-719-053-09 LED SML-310VTT86 (6) (CA600X)
D5748-719-038-05 LED CL-190FG-CD-T (5) (CA600)
D5748-719-053-09 LED SML-310VTT86 (5) (CA600X)
D5758-719-038-05 LED CL-190FG-CD-T (4/SHUF) (CA600)
D5758-719-053-09 LED SML-310VTT86 (4/SHUF) (CA600X)
D5768-719-038-05 LED CL-190FG-CD-T (3/REP) (CA600)
D5768-719-053-09 LED SML-310VTT86 (3/REP) (CA600X)
D5778-719-038-05 LED CL-190FG-CD-T (2/DISC +) (CA600)
D5778-719-053-09 LED SML-310VTT86 (2/DISC +) (CA600X)
D5788-719-038-05 LED CL-190FG-CD-T (1/DISC –) (CA600)
D5788-719-053-09 LED SML-310VTT86 (1/DISC –) (CA600X)
D5798-719-038-05 LED CL-190FG-CD-T (ATT) (CA600)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
D5798-719-053-09 LED SML-310VTT86 (ATT) (CA600X)
D5808-719-038-05 LED CL-190FG-CD-T (AF) (CA600)
D5808-719-053-09 LED SML-310VTT86 (AF) (CA600X)
D5818-719-053-09 LED SML-310VTT86 (DSPL) (CA600X)
D5818-719-078-21 LED SML-310PTT86 (DSPL) (CA600)
D5828-719-053-09 LED SML-310VTT86 (VOL2) (CA600X)
D5828-719-078-21 LED SML-310PTT86 (VOL2) (CA600)
D5838-719-053-09 LED SML-310VTT86 (VOL1) (CA600X)
D5838-719-078-21 LED SML-310PTT86 (VOL1) (CA600)
D5848-719-038-05 LED CL-190FG-CD-T (MODE) (CA600)
LED549 6-500-083-01 LED NSPW315BSRS (LCD BACK LIGHT)
LED550 6-500-083-01 LED NSPW315BSRS (LCD BACK LIGHT)
< LIQUID CRYSTAL DISPLAY >
< DIODE >
< TRANSISTOR >
D5848-719-053-09 LED SML-310VTT86 (MODE) (CA600X)
D5858-719-053-09 LED SML-310VTT86 (SOURCE) (CA600X)
D5858-719-078-21 LED SML-310PTT86 (SOURCE) (CA600)
D5868-719-053-09 LED SML-310VTT86 (VOL5) (CA600X)
D5868-719-078-21 LED SML-310PTT86 (VOL5) (CA600)
D5878-719-053-09 LED SML-310VTT86 (SEL) (CA600X)
D5878-719-078-21 LED SML-310PTT86 (SEL) (CA600)
D5888-719-053-09 LED SML-310VTT86 (VOL4) (CA600X)
D5888-719-078-21 LED SML-310PTT86 (VOL4) (CA600)
D5898-719-053-09 LED SML-310VTT86 (VOL3) (CA600X)
D5898-719-078-21 LED SML-310PTT86 (VOL3) (CA600)
< IC >
IC5018-759-366-34 IC LC75824E
IC5528-749-017-35 IC KSM-401N
< JUMPER RESISTOR >
JR5011-216-864-11 METAL CHIP05%1/16W
JR5021-216-864-11 METAL CHIP05%1/16W
JR5031-216-864-11 METAL CHIP05%1/16W
JR5041-216-864-11 METAL CHIP05%1/16W
JR5051-216-864-11 METAL CHIP05%1/16W
JR5061-216-295-11 SHORT0(CA600)
JR5071-216-864-11 METAL CHIP05%1/16W
(CA600)
JR5081-216-864-11 METAL CHIP05%1/16W
JR5091-216-864-11 METAL CHIP05%1/16W
JR5101-216-864-11 METAL CHIP05%1/16W
JR5111-216-864-11 METAL CHIP05%1/16W
(CA600)
JR5121-216-295-11 SHORT0
JR5131-216-864-11 METAL CHIP05%1/16W
JR5141-216-295-11 SHORT0
JR5151-216-864-11 METAL CHIP05%1/16W
JR5161-216-295-11 SHORT0
JR5171-216-864-11 METAL CHIP05%1/16W
(CA600)
JR5181-216-295-11 SHORT0(CA600)
JR5191-216-864-11 METAL CHIP05%1/16W
R5211-218-867-11 RES-CHIP6.8K2%1/16W
R5221-216-821-11 METAL CHIP1K5%1/16W
R5231-216-821-11 METAL CHIP1K5%1/16W
R5241-216-821-11 METAL CHIP1K5%1/16W
R5251-216-821-11 METAL CHIP1K5%1/16W
R5261-216-825-11 METAL CHIP2.2K5%1/16W
(CA600)
R5501-216-822-11 METAL CHIP1.2K5%1/16W
(CA600)
R5511-216-807-11 METAL CHIP685%1/16W
R5521-216-819-11 METAL CHIP6805%1/16W
R5531-216-813-11 METAL CHIP2205%1/16W
R5541-216-857-11 METAL CHIP1M5%1/16W
R5551-216-850-11 METAL CHIP270K5%1/16W
R5561-216-821-11 METAL CHIP1K5%1/16W
R5571-216-821-11 METAL CHIP1K5%1/16W
R5581-216-821-11 METAL CHIP1K5%1/16W
R5601-220-373-11 RES-CHIP6205%1/16W
R5611-216-819-11 METAL CHIP6805%1/16W
R5621-216-819-11 METAL CHIP6805%1/16W
R5631-216-819-11 METAL CHIP6805%1/16W
R5641-216-819-11 METAL CHIP6805%1/16W
R5651-216-819-11 METAL CHIP6805%1/16W
R5661-216-819-11 METAL CHIP6805%1/16W
R5671-216-819-11 METAL CHIP6805%1/16W
R5681-216-819-11 METAL CHIP6805%1/16W
R5691-216-819-11 METAL CHIP6805%1/16W
R5701-216-819-11 METAL CHIP6805%1/16W
R5711-216-819-11 METAL CHIP6805%1/16W
R5721-216-819-11 METAL CHIP6805%1/16W
R5731-216-819-11 METAL CHIP6805%1/16W
R5741-216-819-11 METAL CHIP6805%1/16W
R5751-216-819-11 METAL CHIP6805%1/16W
R5761-216-819-11 METAL CHIP6805%1/16W
R5771-216-819-11 METAL CHIP6805%1/16W
R5781-216-819-11 METAL CHIP6805%1/16W
R5791-216-822-11 METAL CHIP1.2K5%1/16W
R5801-216-822-11 METAL CHIP1.2K5%1/16W
R5811-216-819-11 METAL CHIP6805%1/16W
IC4018-759-827-14 IC TA8268AH
IC4028-759-653-27 IC TDA7402TR
IC6018-759-492-59 IC SAA6588T-118
IC6028-759-909-71 IC BA4558F
IC8016-801-174-01 IC MN101C49KCF
IC8026-701-405-01 IC PST3443UL
IC8038-759-096-16 IC MM1175XFF
< JUMPER RESISTOR >
D8191-216-295-11 SHORT0
D8201-216-295-11 SHORT0
JR7011-216-864-11 METAL CHIP05%1/16W
JR7031-216-864-11 METAL CHIP05%1/16W
JR8031-216-295-11 SHORT0
JR8041-216-864-11 METAL CHIP05%1/16W
JR9011-216-864-11 METAL CHIP05%1/16W
JR9031-216-864-11 METAL CHIP05%1/16W
R4011-216-813-11 METAL CHIP2205%1/16W
R4021-216-813-11 METAL CHIP2205%1/16W
R4031-216-813-11 METAL CHIP2205%1/16W
R4041-216-813-11 METAL CHIP2205%1/16W
R4061-216-841-11 METAL CHIP47K5%1/16W
R4071-216-864-11 METAL CHIP05%1/16W
R4081-216-841-11 METAL CHIP47K5%1/16W
R4091-216-864-11 METAL CHIP05%1/16W
R4101-216-841-11 METAL CHIP47K5%1/16W
R4121-216-841-11 METAL CHIP47K5%1/16W
R4131-216-821-11 METAL CHIP1K5%1/16W
R4141-216-833-11 METAL CHIP10K5%1/16W
R4151-216-821-11 METAL CHIP1K5%1/16W
R4161-216-833-11 METAL CHIP10K5%1/16W
R4171-216-841-11 METAL CHIP47K5%1/16W
< TRANSISTOR >
< RESISTOR >
< JACK >
PJ4011-774-700-11 JACK, PIN 6P (BUS AUDIO IN,
AUDIO OUT FRONT/REAR)
PJ6011-793-598-11 JACK (ANTENNA)
R4181-216-825-11 METAL CHIP2.2K5%1/16W
R4191-216-821-11 METAL CHIP1K5%1/16W
R4201-216-833-11 METAL CHIP10K5%1/16W
R6011-216-864-11 METAL CHIP05%1/16W
R6021-216-809-11 METAL CHIP1005%1/16W
R6031-216-809-11 METAL CHIP1005%1/16W
R6041-218-867-11 RES-CHIP6.8K5%1/16W
R6051-216-845-11 METAL CHIP100K5%1/16W
R6061-216-841-11 METAL CHIP47K5%1/16W
R6071-216-817-11 METAL CHIP4705%1/16W
R6081-216-797-11 METAL CHIP105%1/16W
R6091-216-823-11 METAL CHIP1.5K5%1/16W
R6101-216-821-11 METAL CHIP1K5%1/16W
R6111-216-853-11 METAL CHIP470K5%1/16W
R6121-216-797-11 METAL CHIP105%1/16W
R6131-216-825-11 METAL CHIP2.2K5%1/16W
R6141-216-825-11 METAL CHIP2.2K5%1/16W
R6151-216-833-11 METAL CHIP10K5%1/16W
R6161-216-825-11 METAL CHIP2.2K5%1/16W
R6171-216-833-11 METAL CHIP10K5%1/16W
R6181-216-809-11 METAL CHIP1005%1/16W
R6191-216-845-11 METAL CHIP100K5%1/16W
R6201-216-809-11 METAL CHIP1005%1/16W
R6211-216-857-11 METAL CHIP1M5%1/16W
R6231-216-833-11 METAL CHIP10K5%1/16W
R7011-216-841-11 METAL CHIP47K5%1/16W
R7031-216-864-11 METAL CHIP05%1/16W
R7041-216-864-11 METAL CHIP05%1/16W
R7051-216-864-11 METAL CHIP05%1/16W
R8011-216-821-11 METAL CHIP1K5%1/16W
R8021-216-835-11 METAL CHIP15K5%1/16W
R8041-247-807-31 CARBON1005%1/4W
R8051-216-809-11 METAL CHIP1005%1/16W
R8061-216-809-11 METAL CHIP1005%1/16W
R8071-216-809-11 METAL CHIP1005%1/16W
R8081-218-716-11 METAL CHIP10K0.5%1/16W
R8091-218-716-11 METAL CHIP10K0.5%1/16W
R8101-218-716-11 METAL CHIP10K0.5%1/16W
R8111-216-845-11 METAL CHIP100K5%1/16W
R8121-216-841-11 METAL CHIP47K5%1/16W
R8131-216-809-11 METAL CHIP1005%1/16W
R8141-216-809-11 METAL CHIP1005%1/16W
R8151-216-809-11 METAL CHIP1005%1/16W
R8161-216-813-11 METAL CHIP2205%1/16W
R8171-216-809-11 METAL CHIP1005%1/16W
R8181-216-809-11 METAL CHIP1005%1/16W
R8191-216-837-11 METAL CHIP22K5%1/16W
R8201-216-809-11 METAL CHIP1005%1/16W
R8211-216-809-11 METAL CHIP1005%1/16W
R8221-216-809-11 METAL CHIP1005%1/16W
R8231-216-833-11 METAL CHIP10K5%1/16W
R8241-216-833-11 METAL CHIP10K5%1/16W
R8251-216-821-11 METAL CHIP1K5%1/16W
R8261-216-849-11 METAL CHIP220K5%1/16W
R8271-216-845-11 METAL CHIP100K5%1/16W
R8281-216-849-11 METAL CHIP220K5%1/16W
R8291-216-809-11 METAL CHIP1005%1/16W
R8301-216-809-11 METAL CHIP1005%1/16W
R8311-216-845-11 METAL CHIP100K5%1/16W
(CA600)
R8321-216-845-11 METAL CHIP100K5%1/16W
R8331-216-864-11 METAL CHIP05%1/16W
R8341-216-864-11 METAL CHIP05%1/16W
R8351-216-845-11 METAL CHIP100K5%1/16W
R8361-216-809-11 METAL CHIP1005%1/16W
R8371-216-864-11 METAL CHIP05%1/16W
R8381-216-821-11 METAL CHIP1K5%1/16W
R8391-216-821-11 METAL CHIP1K5%1/16W
R8401-216-821-11 METAL CHIP1K5%1/16W
R8411-216-864-11 METAL CHIP05%1/16W
R8421-216-864-11 METAL CHIP05%1/16W
R8451-247-887-00 CARBON220K5%1/4W
R8461-216-849-11 METAL CHIP220K5%1/16W
R8471-247-887-00 CARBON220K5%1/4W
R8481-247-887-00 CARBON220K5%1/4W
R8491-216-809-11 METAL CHIP1005%1/16W
R8501-216-809-11 METAL CHIP1005%1/16W
R8511-216-809-11 METAL CHIP1005%1/16W
R8521-216-809-11 METAL CHIP1005%1/16W
R8531-216-809-11 METAL CHIP1005%1/16W
R8541-216-809-11 METAL CHIP1005%1/16W
R8551-216-864-11 METAL CHIP05%1/16W
R8561-216-864-11 METAL CHIP05%1/16W
R8571-216-864-11 METAL CHIP05%1/16W
R8581-216-864-11 METAL CHIP05%1/16W
R8591-216-864-11 METAL CHIP05%1/16W
R8601-216-864-11 METAL CHIP05%1/16W
R8661-216-845-11 METAL CHIP100K5%1/16W
R8671-216-845-11 METAL CHIP100K5%1/16W
R8681-216-845-11 METAL CHIP100K5%1/16W
(CA600)
R8691-216-845-11 METAL CHIP100K5%1/16W
R9011-216-821-11 METAL CHIP1K5%1/16W
R9031-249-425-11 CARBON4.7K5%1/4W
R9041-216-821-11 METAL CHIP1K5%1/16W
R9051-216-841-11 METAL CHIP47K5%1/16W
R9061-216-833-11 METAL CHIP10K5%1/16W
R9071-216-833-11 METAL CHIP10K5%1/16W
R9081-216-841-11 METAL CHIP47K5%1/16W
R9091-216-841-11 METAL CHIP47K5%1/16W
R9101-216-829-11 METAL CHIP4.7K5%1/16W
R9111-216-845-11 METAL CHIP100K5%1/16W
R9131-249-427-11 CARBON6.8K5%1/4W
R9141-216-845-11 METAL CHIP100K5%1/16W
R9151-216-825-11 METAL CHIP2.2K5%1/16W
R9221-247-816-11 CARBON2405%1/4W
R9231-216-845-11 METAL CHIP100K5%1/16W
R9241-249-421-11 CARBON2.2K5%1/4W
R9251-216-821-11 METAL CHIP1K5%1/16W
R9261-249-413-11 CARBON4705%1/4W
R9271-249-417-11 CARBON1K5%1/4W
R9301-216-845-11 METAL CHIP100K5%1/16W
R9311-249-421-11 CARBON2.2K5%1/4W
R9321-216-805-11 METAL CHIP475%1/16W
R9331-216-841-11 METAL CHIP47K5%1/16W
R9341-216-845-11 METAL CHIP100K5%1/16W
R9351-249-421-11 CARBON2.2K5%1/4W
CN11-815-352-11 CONNECTOR, BOARD TO BOARD 30P
CN31-816-275-11 CONNECTOR, FFC/FPC 6P
< JUMPER RESISTOR >
FB11-216-864-11 METAL CHIP05%1/16W
FB21-216-864-11 METAL CHIP05%1/16W
FB31-216-864-11 METAL CHIP05%1/16W
FB41-216-864-11 METAL CHIP05%1/16W
FB61-216-864-11 METAL CHIP05%1/16W
IC18-759-699-98 IC uPD63711GC-8EU
IC28-759-658-87 IC BA5810FP-E2
< TRANSISTOR >
Q18-729-904-87 TRANSISTOR 2SB1197K-R
< RESISTOR >
R31-216-797-11 METAL CHIP105%1/16W
R51-218-344-11 RES-CHIP7.5K5%1/16W
R61-216-837-11 METAL CHIP22K5%1/16W
R71-216-839-11 METAL CHIP33K5%1/16W
R81-216-833-11 METAL CHIP10K5%1/16W
R91-216-840-11 METAL CHIP39K5%1/16W
R101-216-835-11 METAL CHIP15K5%1/16W
R121-216-837-11 METAL CHIP22K5%1/16W
R141-216-841-11 METAL CHIP47K5%1/16W
R151-216-841-11 METAL CHIP47K5%1/16W
R171-216-809-11 METAL CHIP1005%1/16W
R181-216-809-11 METAL CHIP1005%1/16W
R191-216-809-11 METAL CHIP1005%1/16W
R201-216-809-11 METAL CHIP1005%1/16W
R211-216-821-11 METAL CHIP1K5%1/16W
R221-216-821-11 METAL CHIP1K5%1/16W
R241-216-864-11 METAL CHIP05%1/16W
R251-216-864-11 METAL CHIP05%1/16W
R261-216-797-11 METAL CHIP105%1/16W
R291-216-833-11 METAL CHIP10K5%1/16W
R301-216-833-11 METAL CHIP10K5%1/16W
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
40
Page 41
CDX-CA600/CA600X
AEP Model
UK Model
CDX-CA600/CA600X
SERVICE MANUAL
Ver 1.1 2002. 04
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of a production country
• CHANGE OF THE OVERALL ASSY CHANGE OF A
PRODUCTION COUNTRY
The production country was changed from Korean to T hailand in the production
process.
Check the part No. for the servo and main boards when servicing and inspecting
the set.
Discrimination
- SERVO BOARD (COMPONENT SIDE) -
- MAIN BOARD (COMPONENT SIDE) -
E Model
CDX-CA600X
(ENG-02002)
SERVO BOARD Part No.
Korean production :1-683-949-11
Thailand production :1-683-660-11
MAIN BOARD Part No.
Korean production :1-683-929-11
Thailand production :1-685-146-11
7-2. CD Mechanism Section (1) ................................................. 13
7-3. CD Mechanism Section (2) ................................................. 14
7-4. CD Mechanism Section (3) ................................................. 15
8. Electrical Parts List............................................................... 16
2
Page 43
CDX-CA600/CA600X
1. CIRCUIT BOARDS LOCATION
DISC IN board
LOAD board
DISPLAY board
SUB board
SERVO board
SPEAKER board
LIMIT board
MAIN board
tuner unit
(TU601)
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
•%: indicates tolerance.
f
•
• C : panel designation.
Note: The components identified by mark 0 or dotted line
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
•Voltages are taken with a VOM (Input impedance 10 MΩ).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
: internal component.
with mark 0 are critical for safety.
Replace only with part number specified.
supply from ACC and BATT cords.
Voltage variations may be noted due to normal produc-
tion tolerances.
Voltage variations may be noted due to normal production tolerances.
F: FM
f: MW/LW
J: CD
4
W or less unless otherwise
• Waveforms
— Servo Board —
(MODE: CD PLAY)
1
16.9344MHz
wd
(XTAL)
IC1
2
3.3msec
IC1
(PACK)
ts
3
uj
(RFO)
IC1
4
1.8Vp-p
5Vp-p
1.5Vp-p
0V
— Main Board —
1
4.332MHz
IC601
(OSCD)
4
2
18.432MHz
IC801
(OSCOUT)
qs
3
32.768kHz
IC801
(XOUT)
qh
5.2Vp-p
2.2Vp-p
5Vp-p
for printed wiring boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•x: parts mounted on the conductor side.
a
•
•: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)parts face are indicated.
• (): Refer to page of Supplement-1.
• (( )) : Refer to page of Service manual.
: Through hole.
(The other layer’s patterns are not indicated.)
5
Approx. 100mVp-p
oa
od
(FEO)
(TEO)
IC1
Approx. 100mVp-p
IC1
0V
33
Page 44
CDX-CA600/CA600X
2. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 3 for Circuit Boards Location.
234567891011121314
1
A
B
C
D
E
F
G
H
I
J
44
Page 45
CDX-CA600/CA600X
A
B
C
D
E
1
234567891011121314
• Semiconductor
Location
Ref. No.Location
IC1E-7
IC2H-7
Q1C-6
TP66
TP64
TP47
R21
TP48
R22
TP74
TP50
TP56
TP76
C71
TP51
TP52
TP58
TP61
TP62
CN1
TP7
TP72
TP80
TP60
TP59
TP71
TP63
R26
R19
TP77
C4
R17
TP9
TP8
TP78
TP70
C27
CN2
C5
C1
R30
Q1
C3
R29
C43
R3
C6
R18
C25
C41
C34
TP11
TP79
C9
C10
C8
C16
C17
C29
TP12
C70
C15
IC1
TP82
TP81
C11
TP83
C14
R5
C13
C18
TP89
R9
C24
TP23
TP84
TP10
TP88
C20
C19
(Page 7)
C23
R8
TP22
TP24
TP25
F
G
H
I
TP73
TP53
TP86
TP87
TP75
TP69
TP57
TP54
R20
TP68
FB5
C44
R31
TP49
TP85
TP19
CN3
TP91
TP90
C26
TP55
TP20
X1
C36
TP92
R7
R6
C22
TP16
TP17
TP34
TP35
TP36
TP46
C38
TP39
BP2
IC2
BP1
TP37
TP38
TP30
TP41
TP40
TP45
TP42
TP31
TP27
R12
R10
C30
TP28
TP44
TP43
R15
TP26
C35
TP29
TP33
TP32
TP15
BP3
TP5
TP4
TP6
TP3
TP2
R14
TP14
BP4
TP18
TP21
TP1
+-+-
J
55
Page 46
CDX-CA600/CA600X
• Refer to page 3 for Waveforms.
3. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 10 for IC Block Diagrams.
CN2
SW3
TP77
TP78
C1C5
TP81
TP82
TP83
TP84
R29
R30
TP79
TP80
C43
Q1
C3
TP9 TP8
R26
R3
C4
TP7
C6
C14
TP10
C13
C11
R5
C15
C10
C9
TP12
TP11
TP89
C18
C19
C20 C23
R9
C24
TP24
TP22
TP25
TP23
R8
IC1
TP88
C35
TP45
TP44
TP43
TP42
TP41
TP40
TP39
TP38
TP37
TP46
TP36
C38
CN1
M902
M901
SW4
SW2
SW1
Note:
•Voltage is dc with respect to
ground under no-signal conditions.
no mark : CD PLAY
1103-933-152-03 ROLLER (S)
1113-931-913-11 RING (ROLLER), RETAINING
1121-659-837-11 LOAD BOARD
1133-338-737-01 SCREW (2X3), +PS
M903A-3315-039-A MOTOR SUB ASSY, LD (LOADING)
IC4018-759-827-14 IC TA8268AH
IC4028-759-653-27 IC TDA7402TR
IC6018-759-492-59 IC SAA6588T-118
IC6028-759-909-71 IC BA4558F
IC8016-801-174-01 IC MN101C49KCF
IC8026-701-405-01 IC PST3443UL
IC8038-759-096-16 IC MM1175XFF
< JUMPER RESISTOR >
D8191-216-295-11 SHORT CHIP0
D8201-216-295-11 SHORT CHIP0
JR7011-216-864-11 METAL CHIP05%1/10W
JR7031-216-864-11 METAL CHIP05%1/10W
JR8011-216-864-11 METAL CHIP05%1/10W
JR8031-216-295-11 SHORT CHIP0
JR9011-216-864-11 METAL CHIP05%1/10W
JR9031-216-864-11 METAL CHIP05%1/10W
R4011-216-813-11 METAL CHIP2205%1/10W
R4021-216-813-11 METAL CHIP2205%1/10W
R4031-216-813-11 METAL CHIP2205%1/10W
R4041-216-813-11 METAL CHIP2205%1/10W
R4061-216-841-11 METAL CHIP47K5%1/10W
R4071-216-864-11 METAL CHIP05%1/10W
R4081-216-841-11 METAL CHIP47K5%1/10W
R4091-216-864-11 METAL CHIP05%1/10W
R4101-216-841-11 METAL CHIP47K5%1/10W
R4121-216-841-11 METAL CHIP47K5%1/10W
R4131-216-821-11 METAL CHIP1K5%1/10W
R4141-216-833-11 METAL CHIP10K5%1/10W
R4151-216-821-11 METAL CHIP1K5%1/10W
R4161-216-833-11 METAL CHIP10K5%1/10W
R4171-216-841-11 METAL CHIP47K5%1/10W
R4181-216-825-11 METAL CHIP2.2K5%1/10W
R4191-216-821-11 METAL CHIP1K5%1/10W
R4201-216-833-11 METAL CHIP10K5%1/10W
R6011-216-864-11 METAL CHIP05%1/10W
R6021-216-809-11 METAL CHIP1005%1/10W
R6031-216-809-11 METAL CHIP1005%1/10W
R6041-218-867-11 RES-CHIP6.8K5%1/10W
R6051-216-845-11 METAL CHIP100K5%1/10W
R6061-216-841-11 METAL CHIP47K5%1/10W
R6071-216-817-11 METAL CHIP4705%1/10W
R6081-216-797-11 METAL CHIP105%1/10W
R6091-216-827-11 METAL CHIP3.3K5%1/10W
R6101-216-821-11 METAL CHIP1K5%1/10W
R6111-216-853-11 METAL CHIP470K5%1/10W
R6121-216-797-11 METAL CHIP105%1/10W
R6131-216-825-11 METAL CHIP2.2K5%1/10W
R6151-216-833-11 METAL CHIP10K5%1/10W
R6161-216-825-11 METAL CHIP2.2K5%1/10W
R6171-216-833-11 METAL CHIP10K5%1/10W
R6181-216-809-11 METAL CHIP1005%1/10W
R6191-216-845-11 METAL CHIP100K5%1/10W
R6201-216-809-11 METAL CHIP1005%1/10W
R6211-216-857-11 METAL CHIP1M5%1/10W
R6231-216-833-11 METAL CHIP10K5%1/10W
R7011-216-841-11 METAL CHIP47K5%1/10W
R7031-216-864-11 METAL CHIP05%1/10W
R7041-216-864-11 METAL CHIP05%1/10W
R8011-216-821-11 METAL CHIP1K5%1/10W
R8021-216-835-11 METAL CHIP15K5%1/10W
R8041-247-807-31 CARBON1005%1/4W
R8051-216-809-11 METAL CHIP1005%1/10W
R8061-216-809-11 METAL CHIP1005%1/10W
R8071-216-809-11 METAL CHIP1005%1/10W
R8081-218-716-11 METAL CHIP10K0.5%1/10W
R8091-218-716-11 METAL CHIP10K0.5%1/10W
R8101-218-716-11 METAL CHIP10K0.5%1/10W
R8111-216-845-11 METAL CHIP100K5%1/10W
R8121-216-841-11 METAL CHIP47K5%1/10W
R8131-216-809-11 METAL CHIP1005%1/10W
R8141-216-809-11 METAL CHIP1005%1/10W
R8151-216-809-11 METAL CHIP1005%1/10W
R8161-216-813-11 METAL CHIP2205%1/10W
R8171-216-809-11 METAL CHIP1005%1/10W
R8181-216-809-11 METAL CHIP1005%1/10W
R8191-216-837-11 METAL CHIP22K5%1/10W
R8201-216-809-11 METAL CHIP1005%1/10W
R8211-216-809-11 METAL CHIP1005%1/10W
R8221-216-809-11 METAL CHIP1005%1/10W
R8231-216-833-11 METAL CHIP10K5%1/10W
R8241-216-833-11 METAL CHIP10K5%1/10W
R8251-216-821-11 METAL CHIP1K5%1/10W
R8261-216-849-11 METAL CHIP220K5%1/10W
R8271-216-845-11 METAL CHIP100K5%1/10W
R8281-216-849-11 METAL CHIP220K5%1/10W
R8291-216-809-11 METAL CHIP1005%1/10W
R8301-216-809-11 METAL CHIP1005%1/10W
R8311-216-849-11 METAL CHIP220K5%1/10W
(CA600)
R8321-216-845-11 METAL CHIP100K5%1/10W
R8341-216-864-11 METAL CHIP05%1/10W
R8351-216-845-11 METAL CHIP100K5%1/10W
R8361-216-809-11 METAL CHIP1005%1/10W
R8381-216-821-11 METAL CHIP1K5%1/10W
R8391-216-821-11 METAL CHIP1K5%1/10W
R8401-216-821-11 METAL CHIP1K5%1/10W
R8421-216-864-11 METAL CHIP05%1/10W
R8451-247-887-00 CARBON220K5%1/4W
R8461-216-849-11 METAL CHIP220K5%1/10W
R8471-247-887-00 CARBON220K5%1/4W
R8481-247-887-00 CARBON220K5%1/4W
R8491-216-809-11 METAL CHIP1005%1/10W
R8501-216-809-11 METAL CHIP1005%1/10W
R8511-216-809-11 METAL CHIP1005%1/10W
R8521-216-809-11 METAL CHIP1005%1/10W
R8531-216-809-11 METAL CHIP1005%1/10W
R8541-216-809-11 METAL CHIP1005%1/10W
R8591-216-864-11 METAL CHIP05%1/10W
R8601-216-864-11 METAL CHIP05%1/10W
R8661-216-845-11 METAL CHIP100K5%1/10W
R8671-216-845-11 METAL CHIP100K5%1/10W
R8681-216-845-11 METAL CHIP100K5%1/10W
R9011-216-821-11 METAL CHIP1K5%1/10W
R9031-249-425-11 CARBON4.7K5%1/4W
R9041-216-821-11 METAL CHIP1K5%1/10W
R9051-216-841-11 METAL CHIP47K5%1/10W
R9061-216-833-11 METAL CHIP10K5%1/10W
R9071-216-833-11 METAL CHIP10K5%1/10W
R9081-216-841-11 METAL CHIP47K5%1/10W
R9091-216-841-11 METAL CHIP47K5%1/10W
R9101-216-829-11 METAL CHIP4.7K5%1/10W
R9111-216-845-11 METAL CHIP100K5%1/10W
R9131-249-427-11 CARBON6.8K5%1/4W
R9141-216-845-11 METAL CHIP100K5%1/10W
IC18-759-699-98 IC uPD63711GC-8EU
IC28-759-658-87 IC BA5810FP-E2
< TRANSISTOR >
Q18-729-904-87 TRANSISTOR 2SB1197K-R
19
Page 60
CDX-CA600/CA600X
SERVO
Ref. No.Part No.DescriptionRemark
R31-216-797-11 METAL CHIP105%1/10W
R51-218-344-11 RES-CHIP7.5K5%1/10W
R61-216-837-11 METAL CHIP22K5%1/10W
R71-216-839-11 METAL CHIP33K5%1/10W
R81-216-833-11 METAL CHIP10K5%1/10W
R91-216-840-11 METAL CHIP39K5%1/10W
R101-216-835-11 METAL CHIP15K5%1/10W
R121-216-837-11 METAL CHIP22K5%1/10W
R141-216-841-11 METAL CHIP47K5%1/10W
R151-216-841-11 METAL CHIP47K5%1/10W
R171-216-809-11 METAL CHIP1005%1/10W
R181-216-809-11 METAL CHIP1005%1/10W
R191-216-809-11 METAL CHIP1005%1/10W
R201-216-809-11 METAL CHIP1005%1/10W
R211-216-821-11 METAL CHIP1K5%1/10W
R221-216-821-11 METAL CHIP1K5%1/10W
R261-216-797-11 METAL CHIP105%1/10W
R291-216-833-11 METAL CHIP10K5%1/10W
R301-216-833-11 METAL CHIP10K5%1/10W
R311-216-789-11 METAL CHIP2.25%1/10W
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.DateDescription of Revision
1.02001. 12New
1.12002. 04Change of a production country.(ENG-02002)
22
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.