Smooth Fitness CE2.0 User Manual

USER MANUAL - BEDIENUNGSANLEITUNG

CE2.0 Crosstrainer

MODELNUMBER MODELNUMMER: CE2.0

MAX USER WEIGHT - MAX. BENUTZERGEWICHT: 135kg (300 lbs.)

SERVICENUMMER: + 49 (911) 8105924

SERVICEPHONE. 0800 0972100

SERIENNUMMER- SERIALNUMBER (on the frame):

CE2.0 Crosstrainer

2

INDEX – INHALTSVERZEICHNIS

1. English P. 3

2. Deutsch P.23

3

CE2.0 Crosstrainer

PRECAUTIONS

Warning: Before starting any exercise program, it is recommended that you consult your physician, especially for

persons with pre-existing health problems. Before using the new equipment, please review this manual to learn about
the features, functions, and safety operations. It is the responsibility of the owner to ensure that all users of this

equipment are adequately informed of all warnings and precautions. Should you experience any irregular physical

conditions such as dizziness, severe muscle or joint pain, pain in your chest or should any other symptoms appear:

STOP EXERCISING

• Use the crosstrainer only as described in this manual.

• Place on a level surface. To protect the floor or carpet from damage, place a mat under the crosstrainer.

• When choosing a location for the crosstrainer make sure that the location and position permit access to a plug.

• Keep the crosstrainer indoors, away from moisture and dust. Do not put the crosstrainer in a garage or covered

patio, or near water.

• Do not operate the crosstrainer where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the crosstrainer at all times.

• The crosstrainer should not be used by persons weighing more than 300 lbs (135kg)

• Never allow more than one person on the crosstrainer at a time. Wear appropriate exercise clothing when using

the crosstrainer. Do not wear loose clothing that could become caught in the crosstrainer. Athletic support
clothes are recommended for both men and women. Always wear athletic shoes. Never use the crosstrainer
with bare feet, wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on
the same circuit.

• Always examine your crosstrainer before using to ensure all parts are in working order.

• Never insert any object or body parts into any opening.

• Keep the power cord away from moving handle bars and do not run the power cord underneath your

crosstrainer. Do not operate the crosstrainer with a damaged or frayed power cord.

Always unplug the crosstrainer before cleaning and/or servicing. Service to your exercise bike should only be performed
by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these
instructions

will void the crosstrainer warranty.

and consult with your physician immediately.

www.smoothfitness.co.uk

4

CE2.0 Crosstrainer

PREASSEMBLY

Open the boxes:

You are now ready to open the boxes of your new equipment. Make sure to inventory all of the parts that are included in
the boxes. Check the Hardware Comparison Chart for a full count of the number of parts included for this product to be
assembled properly. If you are missing any parts or have any assembly questions call the manufacturer.

Gather your tools:
Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to

assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick
and hassle-free.

Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free

from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable
amount of free area around the unit for unobstructed operation.

Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 135kg (300lbs) it is not

recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown
here. This product is not intended to support users whose weight exceeds this limit

.

www.smoothfitness.co.uk

CE2.0 Crosstrainer

5

PARTS LIST

www.smoothfitness.co.uk

6

CE2.0 Crosstrainer

PARTS LIST

NO. DESCRIPTION QTY NO. DESCRIPTION QTY

A1 MAIN FRAME 1 B1 CENTRAL SUPPORT TUBE 1
A2 MAGNETIC FLYWHEEL 1 B3 WATER BOTTLE 1
A3 FLAT WASHER 2 B5 COMPUTERCABLE; UPPER 1
A4 NUT 2 B6 HAND PULSE SENSOR WIRE 1
A5 TENSION PULLEY 1 B7 BOLT 2
A6 PIPE 3 B8 BUSHING 2
A7 FLAT WASHER 3 B9 SHAFT 1
A8 SCREW 3 B10 BEARING 4

A9 BEARING 4 B11 BUSHING 4
A10 E CLIP 3 B12 CONNECT TUBE 2
A11 MAGNETIC HOUSING 1 B13 FLAT WASHER 6
A12 NUT 1 B14 SPRING WASHER 8
A13 SCREW 1 B15 SCREW 2
A14 SPRING 1 B16 BOTTLE HOUSING 1
A15 COMPUTERCABLE; LOWER 1 B17 SCREW 1
A16 SPRING WASHER 2 B18/19 DECORATION BOTTLE HOUSING 2
A17 SPRING FIXING HOUSING 1 B20 SCREW 4
A18 SCREW 1 B21 SCREW 6
A19 FIXING HOUSING 1 B22 FLAT WASHER 2
A20 SCREW 2
A21 SPRING 1 C1 REAR STABILIZER 1
A22 BELT 1 C2 END CAP 2
A23 BELT PULLEY 1 C3 END CAP COVER 3
A24 PULLEY AXLE 1 C4/D7 BOLT 4
A25 SCREW 4 C5/D8 FLAT WASHER 4
A26 PLANE 1 C6/D9 SPRING WASHER 4
A27 NUT 5 C7/D10 NUT 4
A28 MAGNET 1 D1 FRONT STABILIZER 1
A29 TURNING PLATE 2 D2 END CAP 2
A30 SCREW 2 D3 END CAP COVER 2
A31 DECORATION COVER 2 D4 TRANSMIT WHEEL HOUSING 2
A32 PIPE 2 D5 SCREW 4
A33 BEARING 4 D6 TRANSPORTATION WHEEL 2
A34 FLAT WASHER 2 E1 MONITOR 1
A35 SCREW COVER 2 E2 SCREW 4
A36 SCREW 2 E3 ADAPTOR 1
A37 PEDAL TUBE (RIGHT) 1 F1 FRONT HANDLE BAR (LEFT-RIGHT) 2
A38 PEDAL TUBE (LEFT) 1 F2 HANDLE BAR CLIP 1
A39 SCREW 2 F3 SCREW 2
A40 FLAT WASHER 2 F4 FOAM GRIP 2
A41 FLAT WASHER 2 F5 SENSOR 2
A42 SCREW 2 F6 SCREW 2
A43 CONNECT PIPE 2 G1 SIDE HANDLE BAR 2
A44 SCREW 1 G2 FOAM GRIP 2

www.smoothfitness.co.uk

7

CE2.0 Crosstrainer

PARTS LIST

NO. DESCRIPTION QTY NO. DESCRIPTION QTY

A45 SENSOR WIRE 1 G3 END CAP 2
A46 FIXING HOUSING 1 G4 SCREW 4
A47 RIGHT COVER 1 H1/H2 DECORATION COVER 1
A48 DECORATION COVER 1 H3/H4 PEDAL JOINT COVER 1
A49 LEFT COVER 1 H5/H6 PEDAL 1
A50 DECORATION COVER 1 J1 KNOB 2
A51 SCREW COVER 8 J2 SCREW 4
A52 SCREW 8 J3 SCREW 4
A53 SCREW 3 J4 FLAT WASHER 4
A54 TAPPING SCREW 6 J5 SPRING WASHER 4
A55 POWER CORD SENSOR 1 J6 STARKNOB 4
A56 SCREW 4
A57 TENSION CABLE 1
A58 CLIP 1
A59 SCREW 2
A60 CLIP 2
A61 BUSHING 4
A62 WASHER 4
A63 BOLT 2
A64 NUT 2

www.smoothfitness.co.uk

8

CE2.0 Crosstrainer

EXPLODED DIAGRAM

www.smoothfitness.co.uk

CE2.0 Crosstrainer

9

ASSEMBLY INSTRUCTIONS

First, remove the bolts (C4), washers (C5) and nuts (C6) from rear stabilizer (C). Insert two bolts (C4) through
the rear stabilizer (C) to attach it to the bracket at the back of the main frame (A). Then secure it with washers
(C5), spring washers (C6) and nuts (C7).

A. First remove the bolts (D7), washers (D8) and (D9) as well as nuts (D10) from the front stabilizer (D).

Insert two bolts (D7) through the front stabilizer (D) to attach to the bracket at the front of the main
frame (A). Then secure with washers (D8), spring washers (D9) and nuts (D10)

B. After you complete figure 1 & figure 2, if the machine does not sit level, you can adjust the end caps

(C2) to compensate for uneven floors.

www.smoothfitness.co.uk

10

CE2.0 Crosstrainer

ASSEMBLY INSTRUCTIONS

First remove the bolts (B21), spring washers
(B14) and washers (B13) from the central
support tube (B)
Step 1 Connect the cable (B5) & (A15)
Step 2 Assemble the central support tube (B)
onto the main frame (A) with bolts (B21), spring
washers (B14) and washers (B13)
Attention:
When pushing the tubes together make sure
not to pinch cables.

Remove the screws (E4) from the back of the
monitor (E). Connect the sensor wire (B5 & B6)
with monitor wires and put the monitor on the
fixing plate.

www.smoothfitness.co.uk

CE2.0 Crosstrainer

11

ASSEMBLY INSTRUCTIONS

Pull up right or left connect tube (A43) and
adjust the suitable position which 4 holes are
available when loosing the pop – pin the
middle tube (B) and lower tube (A43) will be
fixed securely
First move the bolts (G4), from the side
handlebar (G). Then slide the side handlebar
(G) over central support tube (B). Secure with
bolts (G4). During handlebar assembly you
have to use the holes as pictured in close up
view. Repeat step 1 and 2 on left connect tube
(A43)

Connect right side handlebar joint covers (H1
& H2) onto side handlebar (G) and secure with
screws (J3). Repeat step 1 on left side
handlebar joint covers

www.smoothfitness.co.uk

12

CE2.0 Crosstrainer

ASSEMBLY INSTRUCTIONS

First, remove the bolts (B7) from the central
support tube (B) and remove the screw (F3)
from the handlebar (F). Connect cables (F5)
to sensor wires (B6). Connect the front
handlebars (F). Connect cables (F5) to
sensor wires (B6). Connect the front
handlebars (F) to central support tube (B)
and twist the bars together. Secure them
with two bolts (B7) and one screw (F3)

Connect right side pedal tube joint covers
(H3 & H4) onto pedal joints and secure with
screws (J2). Repeat again on left side pedal
tube joint covers. Assemble the right pedal
(H6) with washers (J4), spring washers (J5)
and star knobs (J6). There are 3 positions
for moving track. Repeat again on left pedal

www.smoothfitness.co.uk

13

CE2.0 Crosstrainer

ASSEMBLY INSTRUCTIONS

The machine can be operated using the electricity adaptor.

The front stabilizer has built-in transport wheels. To move the machine, stand at the front and lift it up until the
weight of the machine is transferred to the transport wheels. You can now easily move the machine to a new
location.

www.smoothfitness.co.uk