Smeg KE91XE, KE61EBE, KSEIR62E, KSEIR92E, KE91NEE Manual

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.

• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).

• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.

•Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

•If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order

to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances
supplied with energy other than electric, the negative pressure in the room must not exceed 0,04
mbar to prevent fumes being drawn back into the room by the cooker hood.	2°
• In the event of damage to the power cable, it must be replaced by the manufacturer or by the
technical service department, in order to prevent any risks.
• If the instructions for installation for the gas hob specify a greater distance specified above, this has
to be taken into account. Regulations concerning the discharge of air have to be fulfilled.

USE

•The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.

•Never use the hood for purposes other than for which it has been designed.

• Never leave high naked flames under the hood when it is in operation.

•Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.

•Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

•Do not flambè under the range hood; risk of fire

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the appliance.

•“ CAUTION: Accessible parts may become hot when used with cooking appliances.”.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.

• Clean and/or replace the Filters after the specified time period (Fire hazard).

• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicablecollectionpointfortherecyclingofelectricalandelectronicequipment.Byensuringthisproductisdisposedofcorrectly,youwillhelppreventpotentialnegative consequencesfortheenvironmentandhumanhealth,whichcouldotherwisebecausedbyinappropriatewastehandlingofthisproduct.Formoredetailedinformation aboutrecyclingofthisproduct,pleasecontactyourlocalcityoffice,yourhouseholdwastedisposalserviceortheshopwhereyoupurchasedtheproduct.

EN		1
		10

CHARACTERISTICS - INSTALLATION

FIXING OF THE HOOD UNDER THE CABINET

•To drill the cabinet follow the indications given in the dimensional drawing in the chapter which regards hood dimensions.

•To fix the hood onto the cabinet use the 44,4 mm long screws inserting and tightening them from the inside of the cabinet.

Connection to air outlet

AIR OUTLET IN THE DUCTING MODE

When installing the hood in ducting version, basing on the installer’s choice, a rigid or a flexible pipe is used in order to connect the hood to the air outlet piping.

•Insert the flange on the hood body outlet.

•Open the metal grid and make sure that the conversion knob is in the ducting position.

•Connect the hood to the air outlet piping with a pipe.

•Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.

•Remove the charcoal filter if present.

EN

1

11