Skil 6335-02 User Manual
SM 2610956854 09-08 9/18/08 2:51 PM Page 1
IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
Operating/Safety Instructions
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento y seguridad
6335
Call Toll Free for
Consumer Information
& Service Locations
Pour obtenir des informations
et les adresses de nos centres
de service après-vente,
appelez ce numéro gratuit
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
1-877-SKIL999 (1-877-754-5999) www.skil.com
For English Version Version française Versión en español
See page 2 Voir page 10 Ver la página 18
SM 2610956854 09-08 9/18/08 2:51 PM Page 2
General Power Tool Safety Warnings
WARNING
!
Read all safety warnings and instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in all of the warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away while
operating a power tool.
cause you to lose control.
Distractions can
Power
Electrical safety
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools.
and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators.
of electric shock if your body is earthed or
grounded.
Do not expose power tools to rain or wet
conditions.
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts.
entangled cords increase the risk of electric
shock.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
If operating the power tool in damp locations
is unavoidable use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
a GFCI reduce the risk of electric shock.
GFCI and personal protection devices like
electrician’s rubber gloves and footwear will
There is an increased risk
Water entering a power tool will
Unmodified plugs
Damaged or
Use of
further enhance your personal safety.
Do not use AC only rated tools with a DC
power supply.
work, the electrical components of the AC
rated tool are likely to fail and create a hazard
to the operator.
While the tool may appear to
Personal safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of drugs,
alcohol or medication.
while operating power tools may result in
serious personal injury.
Use personal protective equipment. Always
wear eye protection.
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and / or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or plugging in power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench
before turning the power tool on.
or a key left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep proper footing and
balance at all times.
control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts.
clothes, jewelry or long hair can be caught in
moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
-
2
-
A moment of inattention
Protective equipment
A wrench
This enables better
Loose
SM 2610956854 09-08 9/18/08 2:51 PM Page 3
used. Use of dust collection can reduce dustrelated hazards.
Keep handles dry, clean and free from oil
and grease.
control the power tool.
Slippery hands cannot safely
Power tool use and care
Do not force the power tool. Use the
correct power tool for your application.
correct power tool will do the job better and
safer at the rate for which it was designed.
Do not use the power tool if the switch does
not turn it on and off.
cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of
parts and any other condition that may
affect the power tools operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
Any power tool that
Power tools are
The
Such
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
power tool for operations different from those
intended could result in a hazardous situation.
Use clamps or other practical way to secure
and support the workpiece to a stable
platform.
your body is unstable and may lead to loss of
control.
Holding the work by hand or against
Use of the
Service
Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
safety of the power tool is maintained.
Develop a periodic maintenance schedule
for your tool. When cleaning a tool be
careful not to disassemble any portion of
the tool since internal wires may be misplaced
or pinched or safety guard return springs
may be improperly mounted.
cleaning agents such as gasoline, carbon
tetrachloride, ammonia, etc. may damage
plastic parts.
Risk of injury to user. The power cord must
only be serviced by a Skil Factory Service
Center or Authorized Skil Service Station.
This will ensure that the
Certain
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
Safety Rules for Drills
Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the
tool.
Loss of control can cause personal
injury.
Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tools may contact hidden wiring
or its own cord.
will make exposed metal parts of the tool
“live” and shock the operator.
Contact with a “live” wire
Use clamps or other practical way to
secure and support the workpiece to a
stable platform.
or against your body is unstable and may
lead to loss of control.
Do not drill, fasten or break into existing
walls or other blind areas where electrical
wiring may exist.
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.
-
3
-
Holding the work by hand
If this situation is
SM 2610956854 09-08 9/18/08 2:51 PM Page 4
Always wear safety goggles or eye
protection when using this tool. Use a
dust mask or respirator for applications
which generate dust.
Secure the material being drilled. Never
hold it in your hand or across legs.
Unstable support can cause the drill bit to
bind causing loss of control and injury.
Never leave the trigger locked "ON".
Before plugging the tool in, check that the
trigger lock is "OFF".
could cause injury.
Position the cord clear of rotating bit. Do
not wrap the cord around your arm or
wrist.
If you lose control and have the cord
wrapped around your arm or wrist it may
entrap you and cause injury.
Position yourself to avoid being caught
between the tool or side handle and walls
or posts.
jammed in the work, the reaction torque of
the tool could crush your hand or leg.
If the bit becomes bound in the
workpiece, release the trigger
immediately, reverse the direction of
rotation and slowly squeeze the trigger to
back out the bit.
reaction torque. The drill body will tend to
twist in the opposite direction as the drill bit is
rotating.
Do not grasp the tool or place your hands
too close to the spinning chuck or drill
bit.
Do not use the switch "Lock-ON" feature
in situations where drill bit binding is
likely. (For example: just before the bit is
ready to break through the material,
anytime when using a "Hole Saw", auger
bits........ etc.)
body will twist or kick-back in opposite
direction and the release of the trigger "LockON" may be difficult.
Be aware of the location and setting of
the switch "Lock-ON" button.
is locked "ON" during the use, be ready for
emergency situations to switch it "OFF", by
first pulling the trigger then immediately
releasing it without pressing the "Lock-ON"
button.
When installing a drill bit, insert the shank
of the bit well within the jaws of the
Should the bit become bound or
Your hand may be lacerated.
When the bit binds, the drill's
Accidental start-ups
Be ready for a strong
If the switch
chuck.
enough, the grip of the jaws over the bit is
reduced and the loss of control is increased.
Do not use dull or damaged bits and
accessories.
greater tendency to bind in the workpiece.
When removing the bit from the tool avoid
contact with skin and use proper
protective gloves when grasping the bit
or accessory.
prolonged use.
Check to see that keys and adjusting
wrenches are removed from the drill
before switching the tool "ON".
wrenches can fly away at high velocity
striking you or a bystander.
Do not run the drill while carrying it at
your side.
entangled with clothing and injury may result.
This tool may be used with sanding and
polishing disks, grinding wheels, wire
wheel and wire cup brushes. These
accessories must be rated for at least the
speed recommended on the tool warning
label.
running over rated speed can fly apart and
cause injury.
Avoid bouncing and snagging the wheels,
discs or brushes especially when working
corners, sharp edges, etc.
loss of control and kickback.
!
grinding, drilling, and other construction
activities contains chemicals known to
cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement
and other masonry products, and
Arsenic and chromium from chemically-
•
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such
as those dust masks that are specially
designed to filter out microscopic particles.
If the bit is not inserted deep
Dull or damaged bits have a
Accessories may be hot after
A spinning drill bit could become
Wheels and other accessories
This can cause
WARNING
Some dust created by
power sanding, sawing,
Keys or
-4-
0
SM 2610956854 09-08 9/18/08 2:51 PM Page 5
Symbols
IMPORTANT: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate the
tool better and safer.
Symbol Name Designation/Explanation
V Volts Voltage (potential)
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
Diameter Size of drill bits, grinding wheels, etc.
n
0
.../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed,
0 Off position Zero speed, zero torque...
1, 2, 3, ... Selector settings Speed, torque or position settings.
I, II, III, Higher number means greater speed
No load speed Rotational speed, at no load
orbits etc. per minute
Infinitely variable selector with off Speed is increasing from 0 setting
Arrow Action in the direction of arrow
Alternating current Type or a characteristic of current
Direct current Type or a characteristic of current
Alternating or direct current Type or a characteristic of current
Class II construction Designates Double Insulated
Construction tools.
Earthing terminal Grounding terminal
Warning symbol Alerts user to warning messages
Li-ion RBRC seal Designates Li-ion battery recycling
program
This symbol designates
that this tool is listed by
Underwriters Laboratories.
This symbol designates
that this tool is listed by
the Canadian Standards
Association.
This symbol designates that this tool is listed by the Intertek Testing
This symbol designates that
this tool is listed by the
Canadian Standards
Association, to United States
and Canadian Standards.
This symbol designates that
this tool is listed by
Underwriters Laboratories, to
United States and Canadian
Standards.
This symbol
designates
that
this tool
complies
to NOM
Mexican
Standards.
Services, to United States and Canadian Standards.
-5-
SM 2610956854 09-08 9/18/08 2:51 PM Page 6
Functional Description and Specifications
WARNING
!
Disconnect the plug from the power source before making any
assembly, adjustments or changing accessories
measures reduce the risk of starting the tool accidentally.
Drill
FIG. 1
REVERSING
LEVER
VARIABLE SPEED
CONTROLLED
TRIGGER SWITCH
CHUCK
AUXILIARY
HANDLE
HAND GRIP
THUMB
GRIP
FRONT
HOUSING
COLLAR
DRILL LEVEL
. Such preventive safety
VENTILATION
OPENINGS
RUBBERIZED
GRIP
CORD
PROTECTOR
Loosen
Model Chuck Size Mild Hard Soft Wire Cup WireWheel Sanding/
No.
6335 1/2” Keyed 1/2” 1” 1-1/2” 2-3/4” 4” 5”
and type
Tighten
MAXIMUM CAPACITIES
Metal Wood Wood Brushes brushes Polishing
“LOCK-ON”
BUTTON
CHUCK KEY &
STORAGE AREA
NOTE: For tool specifications refer to the nameplate on your tool.
-6-
SM 2610956854 09-08 9/18/08 2:51 PM Page 7
Operating Instructions
VARIABLE SPEED CONTROLLED
TRIGGER SWITCH
Your tool is equipped with a variable speed trigger
switch. The tool can be turned "ON" or "OFF" by
squeezing or releasing the trigger. The speed can
be adjusted from the minimum to maximum
nameplate RPM by the pressure you apply to the
trigger. Apply more pressure to increase the
speed and release pressure to decrease speed
(Fig. 1).
"LOCK-ON" BUTTON
The "Lock-ON" button, located in the handle of
your tool allows for continuous operation at
maximum RPM without holding the trigger
(Fig. 1).
TO LOCK TRIGGER "ON": squeeze trigger,
depress button and release trigger.
CHUCK KEY & STORAGE AREA
Your tool is equipped with a chuck key that is
conveniently located on the cord protector
where it is always handy and unlikely to get lost
or misplaced (Fig. 1).
INSERTING BIT
For small bits, open jaws enough to insert the
bit up to the flutes. For large bits, insert the bit
as far as it will go. Center the bit as you close
the jaws by hand. This positions the bit
properly, giving maximum contact between the
chuck jaws and the bit shank.
To tighten chuck, insert key into each of the
three key holes in succession and tighten
TO UNLOCK THE TRIGGER: squeeze trigger
and release it without depressing the "LockON" button.
!
WARNING
the trigger can not be released.
REVERSING SWITCH BUTTON
The reversing switch button is located above
the trigger switch and is used to reverse
rotation of the bit. For forward rotation, (with the
chuck pointed away from you) move button to
the far left. For reverse rotation move the button
to the far right.
CAUTION
!
a complete stop. Shifting during rotation of the
chuck can cause damage to the tool.
clockwise firmly. The chuck can be released by
using one hole only (Fig. 2).
FIG. 2
If the “Lock-ON” button is
continuously being depressed,
Do not change direction of
rotation until the tool comes to
Counter
Clockwise
Clockwise
The auxiliary handle will provide additional
control, support and guidance for the tool. The
handle is adjustable to any position around the
°
360
To mount, rotate lower portion of hand grip
counter-clockwise to loosen, push upward on
thumb grip provided and slide handle
completely over the front housing collar.
To adjust, push upward on thumb grip, move
handle to desired position and securely tighten
the lower portion of hand grip clockwise
(Fig. 1).
AUXILIARY HANDLE
front housing collar.
Your tool is equipped with drill level located on
DRILL LEVEL
top of the housing that will allow you to
accurately enter the workpiece in a horizontal
position (Fig. 1).
USING THE LEVEL: Place drill bit where hole
is to be drilled, position drill so the bubble in the
level is centered between the lines, then start
drilling the hole, once the bit has entered the
workpiece check from time to time to be sure
the bit is maintaining the horizontal position.
-7-
SM 2610956854 09-08 9/18/08 2:51 PM Page 8
Operating Tips
You will extend the life of your bits and do
neater work if you always put the bit in contact
with the work before pulling the trigger. During
the operation, hold the tool firmly and exert
light, steady pressure. Too much pressure at
low speed will stall the tool. Too little pressure
will keep the bit from cutting and cause excess
friction by sliding over the surface. This can be
damaging to both tool and bit.
DRILLING WITH VARIABLE SPEED
The trigger controlled variable speed feature
will eliminate the need for center punches in
hard materials. The variable speed trigger
allows you to slowly increase RPM. By using a
slow starting speed, you are able to keep the
bit from “wandering”. You can increase the
speed as the bit “bites” into the work by
squeezing the trigger.
DRILL BITS
Always inspect drill bits for excessive wear.
Use only bits that are sharp and in good
condition.
TWIST BITS: Available with straight and
reduced shanks for wood and light duty metal
drilling. High speed bits cut faster and last
longer on hard materials.
CARBIDE TIPPED BITS: Used for drilling
stone, concrete, plaster, cement and other
unusually hard nonmetals. Use continuous
heavy feed pressure when employing carbide
tip bits.
DRILLING WOOD
Be certain workpiece is clamped or anchored
firmly. Always apply pressure in a straight line
with the drill bit. Maintain enough pressure to
keep the drill “biting”.
When drilling holes in wood, twist bits can be
used. Twist bits may overheat unless pulled
out frequently to clear chips from flutes.
Use a “back-up” block of wood for work that is
likely to splinter, such as thin materials.
You will drill a cleaner hole if you ease up on
the pressure just before the bit breaks through
the wood. Then complete the hole from the
back side.
DRILLING METAL
There are two rules for drilling hard materials.
First, the harder the material, the greater the
pressure you need to apply to the tool.
Second, the harder the material, the slower the
speed. Here are a couple of tips for drilling in
metal. Lubricate the tip of the bit occasionally
with cutting oil except when drilling soft metals
such as aluminum, copper or cast iron. If the
hole to be drilled is fairly large, drill a smaller
hole first, then enlarge to the required size, it’s
often faster in the long run. Maintain enough
pressure to assure that the bit does not just
spin in the hole. This will dull the bit and greatly
shorten its life.
Use carbide-tipped masonry bit for cinder
block, mortar, common brick, soft stone and
other materials. The amount of pressure to be
used is dependent upon the type of material
being drilled. Soft materials require less
pressure while the hard materials need more
pressure to prevent the drill bit from spinning.
!
safe operating speed is not exceeded by the
nameplate speed of the tool. Do not exceed
the recommended wheel diameter.
You will find the “Lock-ON” button feature a
convenience for the continuous operation
required for rough sanding. Fine sanding and
polishing require “touch”. Select the most
efficient speed.
When using polishing bonnets, alway be sure
the excess string that secures the bonnet is
tucked well within the bonnet during operation.
Work with brushes requires high speeds. Use
of the “Lock-ON” button feature will provide a
much easier operation.
1. Remember, the tips of a wire brush do the
work. Operate the brush with the lightest
pressure so only the tips of the wire come in
contact with the work.
2. If heavier pressures are used, the wires will
be overstressed, resulting in a wiping action;
and if this is continued, the life of the brush will
be shortened due to wire fatigue.
INCORRECT: Excessive pressure can cause wire breakage.
3. Apply the brush to the work in such a way
that as much of the brush face as possible is in
-8-
DRILLING MASONRY
WARNING
Before using an accessory,
be certain that its maximum
SANDING AND POLISHING
WIRE BRUSHES
BRUSHING PRESSURE
SM 2610956854 09-08 9/18/08 2:51 PM Page 9
full contact with the work. Applying the side or
edge of the brush to the work will result in wire
breakage and shortened brush life.
CORRECT: Wire tips doing the work.
Maintenance
Service
WARNING
!
personnel may result in misplacing of
internal wires and components which
could cause serious hazard.
that all tool service be performed by a Skil
Factory Service Center or Authorized Skil
Service Station.
Your Skil tool has been properly lubricated and
is ready to use. It is recommended that tools
with gears be regreased with a special gear
lubricant at every brush change.
The brushes and commutator in your tool have
been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend every
two to six months the brushes be examined.
Only genuine Skil replacement brushes
specially designed for your tool should be
used.
Preventive maintenance
performed by unauthorized
We recommend
TOOL LUBRICATION
CARBON BRUSHES
Accessories
WARNING
!
adequate size conductors that is capable
of carrying the current necessary for your
tool must be used.
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
NOTE: The smaller the gauge number, the
heavier the cord.
If an extension cord is
necessary, a cord with
This will prevent
Bearings which become noisy (due to heavy
BEARINGS
load or very abrasive material cutting) should
be replaced at once to avoid overheating or
motor failure.
Cleaning
WARNING
!
the power supply before cleaning or
performing any maintenance.
be cleaned most effectively with compressed
dry air.
Always wear safety goggles when
cleaning tools with compressed air.
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
attempt to clean by inserting pointed objects
through openings.
CAUTION
!
parts.
Some of these are: gasoline, carbon
tetrachloride, chlorinated cleaning solvents,
ammonia and household detergents that
contain ammonia.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
Tool’s
Ampere
Rating
3-6
6-8
8-10
10-12
12-16
-9-
To avoid accidents always
disconnect the tool from
The tool may
Certain cleaning agents and
solvents damage plastic
Cord Size in A.W.G.
Cord Length in Feet
25
18
18
18
16
14
100
50
16
16
14
16
14
16
14
16
—
12
Wire Sizes in mm
Cord Length in Meters
150 15 30 60 120
0.75
14
0.75
12
0.75
12
1.0
12
—
—
.075
1.0
1.0
2.5
—
1.5
2.5
2.5
4.0
—
2
2.5
4.0
4.0
—
—
Loading...