Sharp XG-SV100W, XG-SV200X User Manual

MODEL
XG-SV100W XG-SV200X
Introduction Easy Start Setup
OPERATION MANUAL
Connections
Operation
Basic
Features
Useful
Appendix
IMPORTANT
• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.
• Before recycling the packag ing, please ensure that you have checked the con­tents of the carton thoroughly against the list of “Supplied accessories” on page
11.
Model No.:
Serial No.:
ii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked of the plug, must be used. Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse cover fi tted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi­ately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the
x
The wire which is coloured blue must be connected to the terminal which is marked
x
The wire which is coloured brown must be connected to the terminal which is marked
x
or and of the same rating as above, which is also indicated on the pin face
Green-and-yellow : Earth Blue : Neutral Brown : Live
plug which is marked by the letter E or by the safety earth symbol or green-and-yellow.
with the letter N or coloured black.
with the letter L or coloured red.
or coloured green
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
iii
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire at­tentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans, Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
iv
Before using the projector, please read this operation manual carefully.

Introduction

Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projec tor, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefi t of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notifi cation of inspection, modifi cation, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING:
WARNING:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.
To reduce the risk of fi re or electric shock, do not
U.S.A. ONLY
expose this product to rain or mois ture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning fl ash with arrowhead sym­bol, within an equilateral triangle, is in­tended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of suffi cient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the pres­ence of important operating and main­tenance (servicing) instructions in the literature accompanying the product.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
WARNING:
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verifi cation.
FCC Regulations state that any unauthorized changes or modifi cations to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equip ment.
U.S.A. ONLY
U.S.A. ONLY
1
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
• cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
• fully cool before removing the lamp unit. Do not touch the glass surface of the lamp unit or the inside of the projector.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
• continue to use the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instr uctions described on pages
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
2
72 to 74.

How to Read this Operation Manual

2
The specifi cations are slightly different, depending on the model. However, you can connect
and operate all models in the same manner.
In this operation manual, the illustration and the screen display are simplifi ed for explanation, and
• may differ slightly from the actual display.
Using the Menu Screen
RETURN button
Press RETURN to return to the
• previous scre en when the menu is displayed.
ENTER button
Adjustment buttons (P/R/O/Q)
MENU button
Menu Selections (Ad justments)
Example: Adjusting “Bright”.
This operatio n can also be performe d by using the buttons on the pro jector.
Press MENU.
1
The “Picture” me nu screen for the selected
• input mode is displayed.
Press Q or O and selec t
2
“Picture ” to adjust.
Example: “Picture” screen menu
Menu item
Picture Audio SIG SCR PRJ Net.
Picture Mode
Contrast 0 Bright Color Tint
Red Blue CLR Temp BrilliantColor C.M.S.1 C.M.S.2 DNR Eco+Quiet
Reset
SEL./ADJ. RETURN
MENU button ENTER button
Adjustment buttons (P/R/O/Q)
RETURN button
Press RETURN to return
• to the previous sc reen when the menu is displayed.
TM
Buttons used in this operation
Button used in this step
Standard
0 0 0 0Sharp 0 0 0 1
Off
Off Level 2 Off
ENTER END
On-screen display
Introduction
46
.........Indicates safeguards for using the projector.
Info
Indicates additional information for setting up and operating the
.......
Note
projector.
For Future Reference
Maintenance
P. 69
Troubleshooting
PP. 81 to 83
Index
P. 87
3

Contents

Preparing
Introduction
How to Read this Operation Manual ......3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
How to Access the PDF Operation
Manuals..............................................10
Accessories ..........................................11
Part Names and Functions ...................12
Side View ............................................... 12
Top View ................................................ 12
Front View .............................................. 12
Rear View (Terminals) .............................. 13
Inserting the Batteries ............................. 15
Usable Range ......................................... 15
Easy Start
Easy Start .............................................16
Setup and Projection .............................. 16
Setup
Setting Up the Projector .......................18
Video Setup............................................ 18
Setting Up the Projector ......................... 18
Standard Setup (Front Projection) ........... 18
Screen Size and Projection Distance ...... 19
Projection (PRJ) Mode ............................ 21
Ceiling-Mount Setup ............................... 21
Connections
Connecting the Projector to
Other Equipment ................................22
Controlling the Projector by
a Computer ........................................25
Connecting the Power Cord .................26
Using
Basic Operation
Turning the Projector On/Off ................27
Turning the Projector On ......................... 27
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 27
Image Projection ..................................28
Shifting the Lens ..................................... 28
Using the Adjustment Feet...................... 29
Adjusting the Focus ................................ 30
Adjusting the Projected Image Size ......... 30
Correcting Trapezoidal Distortion ............ 31
Switching the Input Mode ....................... 34
Adjusting the Volume .............................. 35
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 35
Resize Mode .......................................... 36
Useful Features
Operating with the Remote Control......40
Displaying and Setting the
Break Timer ......................................... 40
Displaying the Pointer ............................. 40
Using the Spot Function ......................... 40
Switching the Eco+Quiet Mode .............. 40
Auto Sync (Auto Sync Adjustment) ......... 41
Freezing a Moving Image ........................ 41
Selecting the Picture Mode ..................... 41
Displaying an Enlarged Portion of
an Image ............................................. 41
Using the Remote Control as the
Wireless Computer Mouse ................... 42
Menu Items ...........................................43
Using the Menu Screen ........................46
Menu Selections (Adjustments) ............... 46
Picture Adjustment (“Picture” Menu) ....48
Selecting the Picture Mode ..................... 48
Adjusting the Image ................................ 48
Adjusting the Color Temperature ............. 49
Adjusting the Colors ............................... 49
Reducing Image Noise (DNR) ................. 50
Eco+Quiet .............................................. 50
Audio Adjustment (“Audio” Menu) ........51
Speaker Setting ...................................... 51
Audio Input ............................................. 51
Audio Output Type Setting ...................... 51
Adjusting the Audio ................................ 51
Signal Adjustment (“SIG” Menu) ..........52
Adjusting the Computer Image ............... 52
Resolution Setting .................................. 52
Auto Sync Adjustment ............................ 52
Signal Type Setting ................................. 52
Setting the Video System ....................... 53
Setting the Video Setup .......................... 53
Selecting the Dynamic Range ................. 53
Checking the Input Signal ....................... 53
Screen Adjustment (“SCR” Menu) ........54
Setting the Resize Mode ......................... 54
Selecting the Wall Color .......................... 54
Setting the Overscan .............................. 54
Setting the On-screen Display ................ 54
Closed Caption ...................................... 55
Selecting a Startup and Background
Image .................................................. 55
Reversing/Inverting Projected Images ..... 55
Selecting the On-screen Display Language
Helpful Functions Set during
Installation (“PRJ” menu) ...................56
Auto Power Off Function ........................ 56
... 55
4
Auto Restart Function ............................. 56
COMPUTER2 Select .............................. 56
STANDBY Mode ..................................... 56
Selecting the Transmission Speed
(RS-232C) ........................................... 56
Fan Mode Setting ................................... 57
System Lock Function ............................ 57
Keylock Function .................................... 58
®
DLP
LinkTM ............................................ 58
®
DLP
LinkTM Invert .................................. 58
Memory Menu ........................................ 59
Rotate Indicator ...................................... 59
Returning to the Default Settings ............ 60
Checking the Lamp Life Status ............... 60
Setting Up the Projector Network
Environment (“Net.” Menu) ................61
Setting a Password ................................ 61
DHCP Client Setting ............................... 62
TCP/IP Setting ........................................ 62
Returning to Default Settings (Network) .. 62
Restart Network Function ....................... 62
Confi rming the Projector Information ....... 63
Viewing Stereoscopic 3D Images .........64
Precautions on Viewing Stereoscopic
3D Images ........................................... 64
Information on the 3D Projection
Function .............................................. 66
Using 3D Viewing Mode ......................... 67
Appendix ................................................ 68
Reference
Appendix
Maintenance .........................................69
Maintenance Indicators ........................70
Regarding the Lamp .............................72
Lamp...................................................... 72
Caution Concerning the Lamp ................ 72
Replacing the Lamp ............................... 72
Removing and Installing the
Lamp Unit ............................................ 73
Resetting the Lamp Timer ...................... 74
Compatibility Chart ..............................75
Attaching the Ceiling-mount
Rotating Module (AN-SV100T) ...........77
Attaching the Terminal Cover to the
Module ...............................................78
Attaching the Ceiling Mount to the
Ceiling ................................................79
Troubleshooting ....................................81
For SHARP Assistance .........................84
Specifi cations .......................................85
Dimensions ...........................................86
Index .....................................................87
Introduction
5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recom mended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The open ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod uct should not be placed in a built-in installation such as a book case or rack unless proper ventilation is provided or the manufacturer's instruc tions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fi t into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug. a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fi t into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre vent damage to the product due to lightning and power-line surges.
6
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fi re or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fi re or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dan ger ous voltage or other hazards. Refer all servicing to qualifi ed service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions: a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those con trols that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualifi ed technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replace ment parts specifi ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fi re, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to per form safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifi ers) that produce heat.
Introduction
DLP® and the DLP logo are registered trademarks of Texas Instruments and
• BrilliantColor Microsoft
TM
and DLP® LinkTM are trademarks of Texas Instruments.
®
and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries. PC/AT is a registered trademark of International Business Machines Corporation in the
• United States.
®
Reader® is a trademark of Adobe Systems Incorporated.
Adobe
• Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or other countries. HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or
• registered trademarks of HDMI Licensing LLC. PJLink is a registered trademark or an application trademark in Japan, the United States,
• Canada, E.U., China and/or other countries/regions.
All other company or product names are trademarks or registered trademarks of their respective companies.
Some IC chips in this product include confi dential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page
72.
Caution concerning the setup of the projector
For minimal servicing and to maintain high
image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Rest your eyes occasionally.
Continuously watching the screen for long
hours will cause eye strain. Take regular breaks to rest your eyes.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing diffi cult. Close the cur tains and dim the lights when setting up the screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the adjustment range (9 degrees) of the adjustment foot.
After the projector is purchased, a faint
smell from the vent may appear when the power is fi rst turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.
When using the projector in high­altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)
When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.
Use the projector at altitudes of 2,300 meters (7,500 feet) or less.
Warning about placing the projector in a high position
When placing the projector in a high position, make cer tain it is carefully secure to avoid personal injury caused by the projector falling down.
Do not subject the projector to hard impact and/or vibration.
Protect the lens so as not to hit or damage the surface of the lens.
Avoid locations with extremes of temperature.
The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.
Ensure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into Standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 70 and 71.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
8
Caution regarding usage of the projector
If you are not to use the projector for a long
time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. Do not carry the projector by holding the
lens. When storing the projector, ensure you
Using the projector in other countries
The power supply voltage and the shape of
the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.
Temperature monitor function
attach the lens cover to the projector. Do not expose the projector to direct
sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other
audio-visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected. Please read the operation manuals of the
projector and the equipment to be connected for instructions on how to make the connections.
If the temperature inside the projector
increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. Refer to “Maintenance Indicators” on pages 70 and 71 for details.
Info
The cooling fan regulates the internal
• temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reser ved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, fre e of charge, to any per son obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation fi le s (the “Font Software”), to reproduce and distribute the Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font Sof tware, and to permit persons to whom the Font Sof tware is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this pe rmission notice shall be included in all copies of one or more of the Font Software typefaces.
The Font Software may be modifi e d, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been modifi ed and is distribute d under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger softwa re package but no copy of one or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, E XPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARR ANTIES OF MERCHANTABILIT Y, FITNESS FOR A PARTICUL AR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIA L DAMAGES, WHETHER IN AN ACTION OF CONTR ACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall not be use d in adver tising or other wise to promote the sale, use or other dealings in this Font Software without prior written authoriz ation from the Gnome Foundation or Bitstream Inc., respectively. For further information, contact: fonts at gnome dot org.
Introduction
9

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe (Windows
Please download Adobe
®
or Macintosh®).
®
Reader® from the Internet (http://www.adobe.com).
®
Reader® on your computer
Accessing the PDF Manuals
For Windows®:
Insert the CD-ROM in the CD-ROM drive. Double click the “My Computer” icon. Double click the “CD-ROM” drive.When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the projector manuals.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the SETUP MANUAL.
Note
If the desired pdf fi le cannot be opened by double clicking the mouse, start Adobe® Reader® fi r s t ,
• then specify the desired fi le using the “File”, “Open” menu.
For Macintosh®:
Insert the CD-ROM in the CD-ROM drive. Double click the “CD-ROM” icon.When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the projector manuals.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the SETUP MANUAL.
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Connecting Pin Assignments ·······················································2 RS-232C Specifi cations and Commands ····································· 4 Operating the Projector Using the PJLinkTM Protocol ·················· 10 Setting up the Projector Network Environment ·························· 11 Controlling the Projector via LAN ··············································· 17 Resetting the Lamp Timer of the Projector via LAN···················· 22 Troubleshooting ·········································································· 24
10

Accessories

Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
Remote control
<RRMCGA960WJSA>
Terminal cover
<CCOVAE119WEF0>
Power cord*
(1) (2) (3) (4)
Introduction
RGB cable
(10' (3.0 m))
<QCNWGA161WJPZ>
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA082WJPZ>
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
Operation manuals (this manual <TINS-F099WJZZ> and CD-ROM <UDSKAA132WJZZ>)
Note
Codes in “< >” are Replacement parts codes.
For Europe, except U.K.
(6' (1.8 m))
<QACCVA024WJPZ>
For U.K. and
Singapore (6' (1.8 m))
<QACCBA104WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA055WJPZ>
Optional accessories
Lamp unit
Ceiling-mount rotating module
Ceiling-mount adaptor
Ceiling-mount bracket
Ceiling-mount unit
Ceiling-mount extension tube
Note
Some of the optional accessories may not be available depending on the region. Please check with
• your nearest Sharp Authorized Projector Dealer or Service Center.
AN-SV10LP AN-SV100T AN-60KT AN-XGCM55 (for U.S.A. only) AN-TK201 <for AN-60KT> AN-TK202 <for AN-60KT> AN-EP101B <for AN-XGCM55> (for U.S.A. only)
11

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.
1 2 3 4 65 8 9 10 11 12 13 14

Side View

1 STANDBY/ON button
For turning the power on and putting the
projector into Standby mode.
27
2 LENS button
For toggling the menu screens for adjustments of the lens (LENS SHIFT, FOCUS, ZOOM, etc.).
3 RETURN button
For returning to the previous menu screen
during menu operations.
4 ENTER button
For setting items selected or adjusted on the menu.
5 INPUT buttons (R/P)
For switching Input mode.
46
46
34
6 Adjustment buttons (P/R/O/Q)
For selecting menu items.
7 VOL –/+ (Volume) buttons (O/Q)
For adjusting the speaker sound level.
8 MENU button
For displaying adjustment and setting screens.
9 KEYSTONE button
For entering the Keystone Correction
mode.
46
31
71 2 3 4 65 8 9 10 11 12 13 14
7
19 2018
17
17
19 2018
10 AUTO SYNC button
For automatically adjusting images when connected to a computer.
11 ECO+QUIET but ton
For lowering the noise of the cooling fan
and extending the lamp life.

Top V i e w

12 Power indicator 13 Lamp indicator 14 Temperature warning indicator

Front View

15 Rotate indicator
Turns on or blinks when the ceiling-mount
46
35
rotating module (AN-SV100T) is connected.
16 Speaker 17 Exhaust vent
51
69
18 Adjustment foot 19 Remote control sensor 20 Lens cover
69
70
70
59
29
41
40
15
70
19
19 15
15
16
16
12
12345 6 7 8 9
12345 6 7 8 9
10
10
11
11

Rear View (Terminals)

1 LAN terminal
Terminal for controlling the projector using a
computer via network.
2 USB terminal
Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.
3 S-VIDEO input terminal
Terminal for connecting video equipment with an S-video terminal.
4 AUDIO 2 input terminal
5 AUDIO 1 input terminal
26
42
23
24 24
6 COMPUTER/COMPONENT 1 input
terminal
Terminal for computer RGB and component signals.
7 AUDIO OUT terminal
Audio output terminal of equipment connected to the audio input terminal.
8 MONITOR OUT* terminal
(Output terminal for computer RGB and component signals)
Terminal for connecting a monitor.
COMPUTER/COMPONENT 2* input terminal
Terminal for computer RGB and component signals.
* You must switch the setting depending on
22, 23
24
24
22, 23
whether you are using the terminal for MONITOR OUT or COMPUTER/COMPONENT 2 input.
1312 14 15 16 17
1312 14 15 16 17
9 HDMI terminal
Terminal for HDMI input.
10 RS-232C terminal
Terminal for controlling the projector using
a computer.
11 VIDEO input terminal
Terminal for connecting video equipment.
12 Exhaust vent 13 Rear adjustment foot 14 Intake vent
22, 23
25
23
69
29
69
15 Kensington Security Standard
connector
16 Remote control sensor
17 AC socket
Connect the supplied power cord.
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
26
15
Introduction
13
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
1
2 3
4 5
6 7 8 9
10
11 12
13 14 15
1 ON button
For turning the power on.
2 STANDBY button
For putting the projector into the Standby mode.
3 MEMORY (1-8) buttons
For displaying each “Load Memory” screen of
“Memory Menu”.
MEMORY MENU button
For displaying the Memory Menu screen.
4 HDMI, COMPUTER 1/2, S-VIDEO, VIDEO
buttons
For switching to the respective input modes.
5 KEYSTONE button
For entering the Keystone Correction mode.
6 AUTO SYNC button
For automatically adjusting images when
connected to a computer.
7 FREEZE button
For freezing images.
8 POINTER button
For displaying the pointer.
9 MOUSE/Adjustment buttons (P/R/O/Q)
42, 46
For moving the computer cursor when with the
• USB connection (using a USB cable). For selecting and adjusting menu items.
27
27
34
31
41
41
40
16
17 18
19 20 21 22
23
24 25 26 27
59
59
10 L-CLICK/EFFECT button
For the Left click when with the USB connection
• (using a USB cable). For changing the pointer or spot area.
11 ZOOM buttons
For adjusting the projected image size.
12 ROTATE b utt on
For setting the rotation angle of the projector when the ceiling-mount rotating module (AN-SV100T) is connected.
13 MAGNIFY buttons
For enlarging/reducing part of the image.
14 PICTURE MODE button
For selecting the appropriate picture.
15 BREAK TIMER button
For displaying the break time.
16 RESIZE button
For switching the picture size (NORMAL, 16:9,
etc.).
17 MENU button
For displaying adjustment and setting screens.
18 AV MUTE button
For temporarily displaying a black screen and turning off the sound.
19 SPOT button
For displaying the spotlight.
20 ENTER button
For setting items selected or adjusted on the
menu.
21 R-CLICK/RETURN button
For the Right click when with the USB
• connection (using a USB cable). For returning to the previous menu screen
• during menu operations.
22 H&V SHIFT but ton
For shifting the lens horizontally and vertically.
23 FOCUS buttons
For adjusting the focus.
24 PAGE UP/PAGE DOWN buttons
Same as the [Page Up] and [Page Down] keys
on a computer keyboard, when with the USB connection (using a USB cable).
25 VOL +/– (Volume) buttons
For adjusting the speaker sound level.
26 ECO+QUIET button
For lowering the noise of the cooling fan and extending the lamp life.
27 3D MODE button
For displaying the 3D mode menu screen.
30
36
46
40
46
42, 40
41
41
40
35
42, 46
29
30
42
35
40
67
14

Inserting the Batteries

2
3
Pull down the tab on the cover and remove the
1
1
cover towards the direction of the arrow.
Insert the batteries.
2
Insert the batteries making sure the polarities correctly match
• the m and n marks inside the battery compartment.
Insert the upper tab of the cover into the opening,
3
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
• Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
• compartment. Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
• Be sure to replace them as soon as possible with new batteries. Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.
Note
Other remote cont rol sensors are located on the rear and the top of the projector. (See pages
The signal from the remote control can be refl ected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
When using the remote control
Ensure that you do not drop it or expose it to
• moisture or high temperature. The remote control may malfunction under a
• fl uorescent lamp. In this case, move the projector away from the fl uorescent lamp.
12 and 13.)
30°
30°
Remote control
Remote control
Remote control sensor
Remote control sensor
30°
30°
33n (10 m)
33n (10 m)
Remote control signal
Remote control signal transmitters
transmitters
15

Easy Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.
3, 8 STANDBY/ON button
6, 7 ENTER button
6 R/P buttons, 7 INPUT buttons
6 O/Q buttons
6 KEYSTONE
button
8 STANDBY button
3 ON button
7 HDMI,
COMPUTER 1/2, S-VIDEO, VIDEO buttons
4, 6 Adjustment
buttons (P/R/O/Q)
6 ENTER button 3 H&V SHIFT button
5 FOCUS buttons
5 ZOOM buttons
P. 18
1. Place the projector facing a wall or a screen
B
2. Connect the projector to the computer and plug the power cord into the AC socket of the projector
When connecting equipment other than a computer, see pages
23 and 24.
3. Turn the projector on
Press STANDBY/ON on the projector or ON on the remote control.
16
BPP. 22, 25, 26
BP. 2 7
4. Adjust the angle
Adjust the projector angle:
• Shift the lens horizontally and vertically.
1 Press H&V SHIFT on the remote control. 2 Press P, R, O or Q on the remote control.
• Adjust the projector angle by rotating the adjustment feet.
BP. 2 9
5. Adjust the focus and the zoom
1 Press FOCUS +/– on the remote control to adjust the focus. 2 Press ZOOM +/– on the remote control to adjust the zoom.
BP. 3 0
6. Correcting the image distortion due to the projection angle
1
Press KEYSTONE on the projector or on the remote control.
2
Press ENTER on the projector or on the remote control.
3
Press
P, R, O or Q
4
Press ENTER to set the position.
5
Repeat the same procedure with the positions for the upper right, lower right and lower
left of the image.
• When the position of the lower left is set, the correction is made and the display disappears.
to move the position for the upper left of the image.
BP. 31
7. Select the Input mode
On the projector Press INPUT R/P to display the INPUT list. Use INPUT R/P to select the Input mode, and
use O/Q to select the audio input terminal.
INPUT list
INPUT Audio
1 COMPUTER1
2 MONITOR OUT
H
HDMI
On the remote control Press HDMI, COMPUTER 1/2, S-VIDEO, VIDEO
to select the Input mode.
On the
projector
On the remote
control
BP. 3 4
Easy Start
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confi rmation message is displayed to put the projector into Standby mode.
On the
projector
On the remote
control
On-screen display
BP. 2 7
17

Setting Up the Projector

Video Setup

If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See page 53.)

Setting Up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector's feet fl at and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See pages 31 to 33.)

Standard Setup (Front Projection)

Place the projector at the required distance from the screen according to the desired picture
size. (See pages 19 and 20.)
Indication of the Projection Image Size and Projection Distance
XG-SV20 0X
(Example: 4:3 Signal Input (Normal Mode))
Picture Size
500" (1270 cm)
200" (508 cm)
100" (254 cm)
80" (203 cm)
60" (152cm)
64" (163 cm
48"
×
36"
(122 cm
×
×
48"
91 cm)
80"
(203 cm
×
160"
×
120"
(406 cm
×
60"
×
152 cm)
122 cm)
5'11"-11'11"
(1.8 m – 3.6 m)
7'11"-15'10"
(2.4 m – 4.8 m)
400"×300" (1016 cm × 762 cm)
×
305 cm)
9'11"-19'10"
(3.0 m – 6.0 m)
19'10"-39'8"
(6.0 m – 12.1 m)
49'6"-99'2"
Projection Distance
(15.1 m – 30.2 m)
XG-SV100W
(Example: 16:10 Signal Input (Normal Mode))
Picture Size
500" (1270 cm)
200" (508 cm)
100" (254 cm)
80" (203 cm)
60" (152cm)
68" (172 cm
51"
×
32"
(129 cm
×
81 cm)
×
42"
18
170" (431 cm
85"
×
53"
(215 cm
×
×
108 cm)
10
'
-12
"
5
'
6
(1.9 m – 3.9 m)
424"×265" (1077 cm × 673 cm)
×
106"
×
269 cm)
135 cm)
"
8'6"-17'1"
(2.6 m – 5.2 m)
10'8
"
-21'4
"
(3.2 m – 6.5 m)
"
21'4
(6.5 m – 13.0 m)
-42'8
"
53'3
Projection Distance
"
-106'8
"
(16.2 m – 32.5 m)

Screen Size and Projection Distance

[For XG-SV200X] 4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Diagonal [F] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
500" (1270 cm) 400" (1016 cm) 813 cm (320") 300" (762 cm) 610 cm (240") 250" (635 cm) 508 cm (200") 200" (508 cm) 406 cm (160") 150" (381 cm) 305 cm (120") 120" (305 cm) 244 cm (96") 100" (254 cm) 203 cm (80")
80" (203 cm) 163 cm (64") 70" (178 cm) 142 cm (56") 60" (152 cm) 122 cm (48") 40" (102 cm) 81 cm (32")
1016 cm
(400")
762 cm
(300") 15.1 m (49' 6") 30.2 m (99' 2") -762 cm (-300") 0 cm (0") ±254 cm (±100")
610 cm
(240") 12.1 m (39' 7") 24.2 m (79' 4") -610 cm (-240") 0 cm (0") ±203 cm (±80")
457 cm
(180") 9.1 m (29' 8") 18.1 m (59' 6") -457 cm (-180") 0 cm (0") ±152 cm (±60")
381 cm
(150") 7.5 m (24' 9") 15.1 m (49' 7") -381 cm (-150") 0 cm (0") ±127 cm (±50")
305 cm
(120") 6.0 m (19' 10") 12.1 m (39' 8") -305 cm (-120") 0 cm (0") ±102 cm (±40")
229 cm
(90") 4.5 m (14' 10") 9.1 m (29' 9") -229 cm (-90") 0 cm (0") ±76 cm (±30")
183 cm
(72") 3.6 m (11' 11") 7.3 m (23' 10") -183 cm (-72") 0 cm (0") ±61 cm (±24")
152 cm
(60") 3.0 m (9' 11") 6.0 m (19' 10") -152 cm (-60") 0 cm (0") ±51 cm (±20")
122 cm
(48") 2.4 m (7' 11") 4.8 m (15' 10") -122 cm (-48") 0 cm (0") ±41 cm (±16")
107 cm
(42") 2.1 m (6' 11") 4.2 m (13' 11") -107 cm (-42") 0 cm (0") ±36 cm (±14")
91 cm
(36") 1.8 m (5' 11") 3.6 m (11' 11") -91 cm (-36") 0 cm (0") ±30 cm (±12")
61 cm
(24") 1.2 m (4' 0") 2.4 m (7' 11") -61 cm (-24") 0 cm (0") ±20 cm (±8")
Distance from the lens center to
the bottom of the image [H]
16:9 Signal Input (16:9 Mode)
Picture (Screen) size Projection distance [L]
Diagonal [F] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
500" (1270 cm) 400" (1016 cm) 886 cm (349") 498 cm (196") 13.2 m (43' 2") 26.4 m (86' 5") -581 cm (-228 300" (762 cm) 664 cm (261") 374 cm (147") 9.9 m (32' 4") 19.8 m (64' 10") -436 cm (-171 19/32") 62 cm (24 33/64") ±166 cm (±65 3/8") 250" (635 cm) 553 cm (218") 311 cm (123") 8.2 m (27' 0") 16.5 m (54' 0") -363 cm (-143") 52 cm (20 200" (508 cm) 443 cm (174") 249 cm (98") 6.6 m (21' 7") 13.2 m (43' 3") -291 cm (-114 150" (381 cm) 332 cm (131") 187 cm (74") 4.9 m (16' 2") 9.9 m (32' 5") -218 cm (-85 120" (305 cm) 266 cm (105") 149 cm (59") 3.9 m (12' 11") 7.9 m (25' 11") -174 cm (-68 100" (254 cm) 221 cm (87") 125 cm (49") 3.3 m (10' 9") 6.6 m (21' 7") -145 cm (-57 13/64") 21 cm (8 11/64") ±55 cm (±21 51/64")
80" (203 cm) 177 cm (70") 100 cm (39") 2.6 m (8' 8") 5.3 m (17' 3") -116 cm (-45 60" (152 cm) 133 cm (52") 75 cm (29") 2.0 m (6' 6") 4.0 m (13' 0") -87 cm (-34 40" (102 cm) 89 cm (35") 50 cm (20") 1.3 m (4' 4") 2.6 m (8' 8") -58 cm (-22
1107 cm
(436") 623 cm (245") 16.4 m (53' 11") 32.9 m (108' 1") -726 cm (-285 62/63") 104 cm (40 6/7") ±277 cm (±108 20/21")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
L1: Minimum projection distance (m/ft) 0.03018F0.03018 L2: Maximum projection distance (m/ft) H1: Lower distance from the lens center to the
bottom of the image (cm/in)
H2: Upper distance from the lens center to the
bottom of the image (cm/in)
W: Distance from the lens center to the center of the
image (cm/in)
F
: Picture diagonal size : 40"-500"
0.06047F0.06047
-1.524
F
0
±0.508
Distance from the lens center to
the bottom of the image [H]
25
/32") 83 cm (32 11/16") ±221 cm (±87 5/32")
25
/64") 42 cm (16 11/32") ±111 cm (±43 37/64")
51
/64") 31 cm (12 1/4") ±83 cm (±32 11/16")
41
/64") 25 cm (9 13/16") ±66 cm (±26 9/64")
3
/4") 17 cm (6 17/32") ±44 cm (±17 7/16")
5
/16") 12 cm (4 29/32") ±33 cm (±13 5/64")
7
/8") 8 cm (3 17/64") ±22 cm (±8 23/32")
4:3 Signal 16:9 Signal
F
/ 0.3048
F
/ 0.3048
F
-1.524
F
/ 2.54
0.03288F0.03288
0.06588F0.06588
-1.45281F-1.45281
0F / 2.54 0.20754F0.20754F / 2.54
F
±0.508
F
/ 2.54
±0.55345F±0.55345
Distance from the
lens center
to the cen ter of
the image[W
Distance from the
lens center
to the cen ter of
the image[W]
27
/64") ±138 cm (±54 15/32")
F
/ 0.3048
F
/ 0.3048
F
/ 2.54
F
/ 2.54
]
Setup
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates that the bottom of the image is below the lens center.
19
Setting Up the Projector (Continued)
[For XG-SV100W] 16:10 Signal Input (Normal Mode)
F
F
Distance from the
lens center
to the cen ter of
the image[W]
23
/64")
17
/64")
11
/64")
3
/32")
Distance from the
lens center
to the cen ter of
the image[W
-1.524
F
/ 0.3048
F
/ 2.54
]
0F / 2.54
F
/ 2.54
Picture (Screen) size Projection distance [L]
Diagonal [F] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
500" (1270 cm) 400" (1016 cm) 862 cm (339") 538 cm (212") 13.0 m (42' 7") 26.0 m (85' 4") -538 cm (-212") 0 cm (0") ±204 cm (±80 300" (762 cm) 646 cm (254") 404 cm (159") 9.7 m (32' 0") 19.5 m (64' 0") -404 cm (-159") 0 cm (0") ±153 cm (±60 250" (635 cm) 538 cm (212") 337 cm (132") 8.1 m (26' 8") 16.3 m (53' 4") -337 cm (-132 1/2") 0 cm (0") ±128 cm (±50 7/32") 200" (508 cm) 431 cm (170") 269 cm (106") 6.5 m (21' 4") 13.0 m (42' 8") -269 cm (-106") 0 cm (0") ±102 cm (±40 150" (381 cm) 323 cm (127") 202 cm (79") 4.9 m (16' 0") 9.8 m (32' 0") -202 cm (-79 120" (305 cm) 258 cm (102") 162 cm (64") 3.9 m (12' 9") 7.8 m (25' 7") -162 cm (-63 19/32") 0 cm (0") ±61 cm (±24 7/64") 100" (254 cm) 215 cm (85") 135 cm (53") 3.2 m (10' 8") 6.5 m (21' 4") -135 cm (-53") 0 cm (0") ±51 cm (±20
80" (203 cm) 172 cm (68") 108 cm (42") 2.6 m (8' 6") 5.2 m (17' 1") -108 cm (-42 13/32") 0 cm (0") ±41 cm (±16 5/64") 60" (152 cm) 129 cm (51") 81 cm (32") 1.9 m (6' 5") 3.9 m (12' 10") -81 cm (-31 40" (102 cm) 86 cm (34") 54 cm (21") 1.3 m (4' 3") 2.6 m (8' 6") -54 cm (-21 13/64") 0 cm (0") ±20 cm (±8 1/32")
1077 cm
(424") 673 cm (265") 16.2 m (53' 3") 32.5 m (106' 8") -673 cm (-265") 0 cm (0") ±255 cm (±100 7/16")
Distance from the lens center to
the bottom of the image [H]
1
/2") 0 cm (0") ±77 cm (±30 9/64")
51
/64") 0 cm (0") ±31 cm (±12 3/64")
4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Diagonal [F] Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
500" (1270 cm) 400" (1016 cm) 813 cm (320") 300" (762 cm) 610 cm (240") 250" (635 cm) 508 cm (200") 200" (508 cm) 406 cm (160") 150" (381 cm) 305 cm (120") 120" (305 cm) 244 cm (96") 100" (254 cm) 203 cm (80")
80" (203 cm) 163 cm (64") 70" (178 cm) 142 cm (56") 60" (152 cm) 122 cm (48") 40" (102 cm) 81 cm (32")
1016 cm
(400")
762 cm
(300") 18.4 m (60' 4") 36.8 m (120' 9") -762 cm (-300") 0 cm (0") ±289 cm (±113 5/7")
610 cm
(240") 14.7 m (48' 3") 29.5 m (96' 8") -610 cm (-240") 0 cm (0") ±231 cm (±90 31/32")
457 cm
(180") 11.0 m (36' 2") 22.1 m (72' 6") -457 cm (-180") 0 cm (0") ±173 cm (±68 7/32")
381 cm
(150") 9.2 m (30' 2") 18.4 m (60' 5") -381 cm (-150") 0 cm (0") ±144 cm (±56 55/64")
305 cm
(120") 7.4 m (24' 1") 14.7 m (48' 4") -305 cm (-120") 0 cm (0") ±116 cm (±45 31/64")
229 cm
(90") 5.5 m (18' 1") 11.0 m (36' 3") -229 cm (-90") 0 cm (0") ±87 cm (±34 7/64")
183 cm
(72") 4.4 m (14' 6") 8.8 m (29' 0") -183 cm (-72") 0 cm (0") ±69 cm (±27 19/64")
152 cm
(60") 3.7 m (12' 1") 7.4 m (24' 2") -152 cm (-60") 0 cm (0") ±58 cm (±22 47/64")
122 cm
(48") 2.9 m (9' 8") 5.9 m (19' 4") -122 cm (-48") 0 cm (0") ±46 cm (±18 3/16")
107 cm
(42") 2.6 m (8' 5") 5.2 m (16' 11") -107 cm (-42") 0 cm (0") ±40 cm (±15 59/64")
91 cm
(36") 2.2 m (7' 3") 4.4 m (14' 6") -91 cm (-36") 0 cm (0") ±35 cm (±13 41/64")
61 cm
(24") 1.5 m (4' 10") 2.9 m (9' 8") -61 cm (-24") 0 cm (0") ±23 cm (±9 3/32")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
L1: Minimum projection distance (m/ft) 0.03247F0.03247 L2: Maximum projection distance (m/ft) H1: Lower distance from the lens center to the
bottom of the image (cm/in)
H2: Upper distance from the lens center to the
bottom of the image (cm/in)
W: Distance from the lens center to the center of the
image (cm/in)
F
: Picture diagonal size : 40"-500"
0.06504F0.06504F / 0.3048 0.07363F0.07363F / 0.3048
-1.3462F-1.3462
F
0
±0.51026F±0.51026
Distance from the lens center to
the bottom of the image [H]
16:10 Signal 4:3 Signal
F
/ 0.3048
F
/ 2.54
0.03676F0.03676
-1.524
0F / 2.54 0
F
±0.57765F±0.57765
/ 2.54
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates that the bottom of the image is below the lens center.
20

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR” menu. See page 55.)
Table mounted, front projection
[Menu item “Front”]
Table mounted, rear projection (with a translucent screen)
[Menu item “Rear”]
a

Ceiling-Mount Setup

It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold separately).
Ceiling mounted, front projection
[Menu item “Ceiling + Front”]
Ceiling mounted, rear projection (with a translucent screen)
[Menu item “Ceiling + Rear”]
Setup
21

Connecting the Projector to Other Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Equipment
Computer
Note
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission may not work property. (The HDMI specifi cation does not support all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.)
You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external equipment. (See page
See page with computer signals other than those listed may cause some of the functions to not work.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
• computer's external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specifi c instructions in
your computer's operation manual to enable your computer's external output port.
75 “Compatibility Chart” for a list of computer signals compatible with the projector. Use
Terminal on
connected equipment
RGB
output
terminal
HDMI output
terminal
56.)
Cable
RGB cable (supp lied) COMPUTER/
HDMI cable (commercially available) HDMI
Terminal o n the
projector
COMPONENT 1, 2
22
Equipment
Video equipment
Terminal on
connected equipment
HDMI output
terminal
Cable
HDMI cable (commercially available) HDMI
Terminal o n the
projector
Camera/Video game
Component
video output
terminal
S-video output
terminal
Video output
terminal
Component
video
output
terminal
S-video
output
terminal
Video
output
terminal
3 RCA to mini D-sub 15 pin cable COMPUTER/
S-video cable (commercially available)
Video cable (commercially available)
Cables for a camera or a vi deo game/3 RCA to mini D-sub 15 pin cable
RCA adaptor plug (commercially available)
Cables for a camera or a vi deo game
Cables for a camera or a vi deo game
COMPONENT 1, 2
S-VIDEO
VIDEO
COMPUTER/ COMPONENT 1, 2
S-VIDEO
VIDEO
Connections
Note
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission may not work property. (The HDMI specifi cation does not support all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.) HDMI (High-Defi nition Multimedia Interface) is a digital AV interface that can deliver a high-defi nition
• video signal, multi-channel audio signal, and bi-directional control signal all in just one cable. Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the
• digital video signal does not degrade when transmitted, and a high-quality image with a simple connection can be enjoyed. You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use
• this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external equipment. (See page When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
56.)
commercially available cable that fi ts in the projector terminal you want to connect. The projector does not support RGBC signals via the Euro-scart.
23
Connecting the Projector to Other Equipment (Continued)
Equipment
Audio equipment
Monitor RGB
Amplifi er
Terminal on
connected equipment
ø3.5 mm
audio output
terminal
RCA audio
output
terminal
Audio
output
terminal
input
terminal
ø3.5 mm
audio input
terminal
RCA audio
input
terminal
Cable
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice pa rt QCNWGA03 8WJPZ)
RCA audio cable (commer ciall y available)
Cables for a camera or a vi deo game
RGB cable (supplied or commer cially available)
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice pa rt QCNWGA03 8WJPZ)
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
Terminal o n the
projector
AUDIO 1
AUDIO 2
MONITOR OUT
AUDIO OUT
Note
You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. To use this terminal as an output terminal, set “COMPUTER2 Select” to “Monitor Output” before connecting the external equipment. (See page When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
56.)
stereo audio cable. You can select “Audio 1”, “Audio 2” or “HDMI” for “Audio Input” in the “Audio” menu. (See page
• RGB signals and Component signals can be output to the monitor.
This projector is able to process the following signals when connected to HDMI equipment:
Video signal: For details, see “Digital Support” in the list of “Compatibility Chart” on page 75.
Audio signal: Linear PCM audio
Sampling frequency: 48kHz/44.1kHz/32kHz
24
51.)

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifi cations and Commands”.
When connecting to a computer using an RS-232C serial control cable
To RS-232C terminal
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Connections
Note
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details. Refer to pages 2 to 9 of the “SETUP MANUAL” contained on the supplied CD-ROM for “Connecting
• Pin Assignments” and “RS-232C Specifi cations and Commands”.
Info
Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector. Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
• This may damage your computer.
25
Controlling the Projector by a Computer (Continued)
When connecting to the LAN terminal using a LAN cable
LINK LED (green) Illuminates when linked.
TX/RX LED (yellow) Illuminates when transmitting/receiving data.
* To ensure safety, do not connect the LAN terminal
with any cables that may cause excessive voltage such as a telephone line.
Hub
or
Computer
To L AN te r minal
LAN cable (Category 5 type, commercially available)
Note
When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially available). When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially
• available).

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.
AC socket
AC socket
Power cord (supplied)
Power cord (supplied)
To AC out let
To AC out let
26

Turning the Projector On/Off

Info

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages
Press STANDBY/ON on the projector or ON on the remote control.
The power indicator illuminates green.
• After the lamp indicator illuminates, the projector
• is ready to start operation.
22 to 26.)
When “Auto Restart ” is set to “On”:
If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page
English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page
56.)
55.
STANDBY/ON button
Note
About the Lamp Indicator
The lamp indicator illuminates to indicate the status of the lamp.
Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down
abnormally or the lamp should be replaced.
When switching on the projector, a slight
• fl ickering of the image may be experienced within the fi rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. If the projector is put into Standby mode and
• immediately turned on again, the lamp may take some time to start projection. When System Lock is set, the keycode input
• box appears. To cancel the keycode setting, input the keycode that you have already set. See page
57 for details.

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confi rmation message is displayed, to put the projector into Standby mode.
The projector cannot be turned on while cooling.
Power indicator
Lamp indicator
STANDBY button
ON button
On-screen display (confi rmation message)
Info
Direct Power O ff function:
You can unplug the power cord from the AC outlet even if the cooling fan is still running.
Operation
Basic
27

Image Projection

Shifting the Lens

In addition to the zoom function and adjustment of projection angle using the adjustment feet, you can adjust the position of the projection using the lens shift function. This is a useful function in cases such as when the screen cannot be moved.
When moving upward or downward When moving in the left and right direction
Adjustable range
Adjustable range
Adjustable range
The adjustable range is shown below.
• Horizontal range: ±25% (XG-SV200X)/±23% (XG-SV100W) Vertical range: ±50% The adjustable range has limitations even within the range shown above. The image can be adjusted as shown on the diagram.
• Allow a margin of error in the value.
XG-SV200X
Position of the image when the image is centered, both vertically and horizontally, in lens shift
0.5V
XG-SV100W
Position of the image when the image is centered, both vertically and horizontally, in lens shift
0.5V
Adjustable range
1V
0.5V
V : Height of the image H : Width of the image
28
1V
0.5V
1H 0.23H0.23H
V : Height of the image
1H 0.25H0.25H
H : Width of the image
Press H&V SHIFT on the remote
1
control.
Pressing ENTER on the projector or on
• the remote control displays the test pattern. Checking the test pattern is useful for more accurate adjustment.
ROn-screen display
END
LENS SHIFT
TESTPATTERN LENS CENTER
Press P, R, O or Q on the
2
projector or the remote control
LENS SHIFT
to adjust the image position.
Note
When RETURN is pressed, the lens shift reset screen is displayed. Lens shift can be reset to factory default with this screen.

Using the Adjustment Feet

When the position of the projected image cannot be
• adjusted with the lens shift function, use the adjustment feet to adjust the projected angle. The height of the projector can be adjusted using the
• adjustment feet when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpendicular to
• the screen as possible.
Rotate the adjustment feet to
1
adjust the projected angle.
The projector is adjustable up to approximately 9 degrees (front) and approximately ±2 degrees (rear) from the standard position.
ENTER button
Adjustment buttons (P/R/O/Q)
RETURN button
H&V SHIFT button
Operation
Basic
Adjustment feet
Warning!
Do not hold the lens and lens cover when projector angle is adjusted. Use caution not to pinch your fi nger in the
• space between the adjustment foot and the projector when the projector angle is lowered.
Down
Up
Up
Down
29
Image Projection (Continued)

Adjusting the Focus

Press FOCUS +/– on the remote control to adjust the focus.
ROn-screen display
FOCUS
TESTPATTERN
Info
It is recommended that the focus be adjusted after the projector has warmed up for at least 30 minutes.

Adjusting the Projected Image Size

Press ZOOM +/– on the remote control to adjust the projected image size.
ROn-screen display
ZOOM
TESTPATTERN
ZOOM buttons
FOCUS buttons
Note
After you have pressed FOCUS or ZOOM on the remote control, you can display the test pattern by pressing ENTER. The test pattern is useful for making more accurate adjustments.
For fi ne adjustments, when H&V SHIFT, FOCUS or ZOOM is pressed, the projected image moves a small amount in the desired direction for approximately one second. Hold down the buttons to move the projected image quickly.
30

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
There are the two types of the Keystone Correction.
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner of the projected image
2) “H&V KEYSTONE” for designating the correction of the horizontal and
vertical axes
Selecting the Type of the Correction
Select the type of the keystone correction.
Press KEYSTONE on the projector or on the remote control.
“GEOMETRIC ADJUSTMENT” will be displayed.
Each time KEYSTONE is pressed, the display
toggles as follows:
GEOMETRIC ADJUSTMENT
The display disappears.
GEOMETRIC ADJUSTMENT
H&V KEYSTONE For correcting an image
H&V KEYSTONE
For correcting an image designating the corner of the projected image
designating the horizontal or vertical axes
KEYSTONE button
ENTER button
Adjustment buttons (P/R/O/Q)
RETURN button
RETURN button
ENTER button
Adjustment buttons (P/R/O/Q)
KEYSTONE button
Operation
Basic
31
Image Projection (Continued)
3
GEOMETRIC ADJUSTMENT
ROn-screen display
Press KEYSTONE on the
1
projector or on the remote control repeatedly until “GEOMETRIC ADJUSTMENT” is displayed.
Press P, R, O or Q to move the
2
position for the upper left of the image.
Press ENTER to set the position.
3
ROn-screen display
H&V KEYSTONE
H&V KEYSTONE
NEXT RESET
NEXT RESET
GEOMETRIC ADJUSTMENT
GEOMETRIC ADJUSTMENT
ADJUST
ADJUST
Repeat the same procedure with
4
the positions for the upper right, lower right and lower left of the image.
At this time, pressing RETURN on the projector or on the remote control returns to the previous screen.
When the position of the lower left is set, t he correction is made and the display disappears.
Geometric Adjustment
Upper Left Upper Right Lower Right
Lower Left
32
H&V KEYSTONE
2
3
Press KEYSTONE on the
1
1
projector or on the remote control repeatedly until “H&V KEYSTONE” is displayed.
ROn-screen display
ROn-screen display
H&V KEYSTONE H:0 V:0
H&V KEYSTONE H:0 V:0
END
END
EXIT TEST PTRN RESET
EXIT TEST PTRN RESET
ADJUST
ADJUST
Press P or R to parallelize the
2
left and right sides of the projected image.
Press O or Q to parallelize the
3
upper and lower sides of the projected image.
Press KEYSTONE to set the
4
position.
Vertical Keystone Correction (Adjustment with
Horizontal Keystone Correction (Adjustment with
' / "
\ / |
)
)
Operation
Basic
33
Image Projection (Continued)

Switching the Input Mode

Select the appropriate input mode for the connected equipment.
Press HDMI, COMPUTER 1/2, S-VIDEO or VIDEO on the remote
control to select the input mode.
When you select the input mode with
INPUT R/P on the projector:
When R/P is pressed, the Input list
• appears. While the Input list is displayed, follow the procedure below to switch the input mode.
INPUT list
INPUT Audio
1 COMPUTER1
2 MONITOR OUT
H
HDMI
S
S-VIDEO
V
VIDEO
–Press R/P to select the desired input
mode and then press ENTER.
If ENTER is not pressed, the projector
• switches to the selected input mode in a few seconds.
Note
When no signal is received, “NO SIGNAL” will be displayed. When non-supported signal is received, “NOT REG.” is displayed.
HDMI, COMPUTER 1/2, S-VIDEO, VIDEO buttons
34

Adjusting the Volume

Press VOL +/– on the remote control or on the projector to adjust the volume.
Note
Pressing VOL– will lower the volume.
• Pressing VOL+ will raise the volume.
When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector's volume to the lowest level when turning the projector on/off or when changing the input signal.
When you do not want to output the sound from the projector's speaker while the projector is connected to external equipment, set “Speaker” in the “Audio” menu to “Off”. (See page
51.)
Displaying the Black Screen and Turning Off the Sound
Temporarily
AV MUTE button
VOL +/– (Volume) buttons
On-screen displayOn-screen display
Operation
Basic
Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.
Note
Pressing AV MUTE again will turn the
• projected image back on.
On-screen display
On-screen display
35
Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
See page 54 for setting on menu screen.
RESIZE
[For XG-SV200X]
COMPUTER
Main resolution NORMAL FULL NATIVE BORDER 16:9
SVGA (800 × 600)
4:3 aspect ratio
Other aspect ratios
Computer Image type NORMAL FULL NATIVE BORDER 16:9
Resolution lower than
XGA
XGA
Resolution
higher than
XGA
XGA (1024 × 768)
SXGA (1152 × 864) 1152 × 864 UXGA (1600 × 1200) 1600 × 1200 SXGA (1280 × 1024) 968 × 768
1280 × 720 1024 × 576 1280 × 720 — 1360 × 768 1024 × 578 1360 × 768 — 1366 × 768 1024 × 576 1366 × 768 — 1280 × 768 1024 × 614 1280 × 768 960 × 576 1280 × 800 1024 × 640 1280 × 800 922 × 576
Inpu t sign al For 4:3 s creen For 16: 9 scre en
4:3 as pect ratio
1024 × 768
1024 × 768
*1
800 × 600
768 × 576
1280 × 1024 720 × 576
*1
RESIZE button
button
1024 × 576
1024 × 576
SXGA (128 0 × 1024)
1280 × 72 0
1360 × 76 8 1366 × 76 8
1280 × 76 8
1280 × 800
: Cutout area on which images cannot be projected : Area where the signals are off screen
*1 Same as NORMAL mode
36
5:4 aspect r atio
16:9 aspect ratio
16:10 aspect ratio
*1
*1
[For XG-SV200X]
VIDEO/DTV
Inpu t sign al For 4:3 s creen For 16: 9 scre en
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH BORDER 16:9
4:3 aspect ratio
I, 48 0P,
480 576
I, 576P,
NTSC, PAL,
SECAM
720P, 1035I,
1080
I, 1080P
540P
: Cutout area on which images cannot be projected : Area on which the image is not included in the original signals
*1 Same as NORMAL mode.
Squeeze
Letter box
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
*1
*1
Operation
Basic
37
Image Projection (Continued)
[For XG-SV100W]
COMPUTER
Main resolution NORMAL FULL NATIVE 16:9
SVGA (800 × 600)
4:3 aspect ratio
Other aspect ratios
Inpu t sign al Output s cree n image
Computer Image type NORMAL FULL NATIVE 16:9
Resolution
XGA and b elow
Resolution
higher than
XGA
SXGA
(1280 × 10 24)
XGA (1024 × 768) 1024 × 768
SXGA (1152 × 864) 1152 × 864
SXGA+ (1400 × 1050) 1400 × 1050
SXGA (1280 × 1024) 1000 × 800 1280 × 1024
1280 × 720 1280 × 720
1366 × 768 1280 × 720 1366 × 768 1280 × 768 1280 × 768 1280 × 800 1280 × 800
4:3 as pect ratio
5:4 aspect r atio
1068 × 800
1280 × 800
800 × 600
1280 × 720
*2
1280 × 720
1360 × 768 1280 × 722 1360 × 768
1280 × 72 0
1360 × 76 8 1366 × 76 8
1280 × 76 8
1280 × 800
: Cutout area on which images cannot be projected
: Area where the signals are off screen *1 Same as NORMAL mode. *2 In case SXGA+ input.
38
16:9 aspect ratio
16:9 aspect ratio
15:9 aspect ratio
16:10 aspect ratio
*1
*1
*1
*1
[For XG-SV100W]
VIDEO/DTV
Inpu t sign al Output s cree n image
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH 16:9
480I, 480 P,
576I, 576P,
NTSC, PAL,
SECAM
720P, 1035I,
1080I, 1080P
540P
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals *1 Same as NORMAL mode.
4:3 aspect ratio
Squeeze
Letter box
16:9 aspect ratio
16:9 aspect ratio
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
*1
About Copyrights
When using the Resize function to select an image size with a different aspect ratio to a TV
• program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size. The use of the Resize or Keystone Correction function to compress or stretch the image for
• commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.
Operation
Basic
39

Operating with the Remote Control

2
AUTO SYNC button FREEZE button POINTER button
SPOT button
Adjustment buttons (P/R/O/Q)
RETURN button EFFECT button MAGNIFY buttons
PICTURE MODE button ECO+QUIET button
BREAK TIMER button

Displaying the Pointer

Press POINTER and press P/R/
1
O/Q on the remote control to move the pointer.
Press EFFECT to change the pointer icon
• (5 types).
Finger1 Finger2 Heart Underline
Star
Press POINTER again.
2
2
The pointer will disappear.

Displaying and Setting the Break Timer

Press BREAK TIMER.
1
The timer starts to count down from 5
• minutes.
On-screen display
Press P/R/O/Q to adjust the
2
length of the break time.
Increases with P or Q
5 minutes 6 minutes 60 minutes
Shortens with O or R
4 minutes 3 minutes 1 minute The break time can be set in units of one
• minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
Note
The Break Timer is not available while the projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute

Using the Spot Function

Press SPOT and press P/R/O/Q
1
on the remote control to move the spot area.
Press EFFECT to change the spot area size (3 types).
1/9 1/25 1/8
Press SPOT again.
2
The spot area will disappear.

Switching the Eco+Quiet Mode

Press ECO+QUIET to switch the Eco+Quiet mode between on and off.
When the Eco+Quiet is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.
Note
Refer to “Eco+Quiet” on page 50 for details.
40
Auto Sync
2
(Auto Sync Adjustment)

Displaying an Enlarged Portion of an Image

Auto Sync function works when detecting input signal after the projector turns on.
Press AUTO SYNC to manually adjust with Auto Sync function.
Note
When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page
52.)

Freezing a Moving Image

Press FREEZE.
1
The projected image is frozen.
Press FREEZE again to return to
2
2
the moving image from the currently connected device.

Selecting the Picture Mode

You can select the appropriate Picture mode for the projected image, such as movie or video game.
Press PICTURE MODE.
When pressing PICTURE MODE, the Picture
• mode changes in the following order:
STANDARD PRESENTATION MOVIE GAME sRGB
Note
See page 48 for details on the Picture mode.
* “sRGB” is displayed only when RGB signal is input.
*
Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations.
Press MAGNIFY on the
1
remote control.
Enlarges the image.
• Pressing
• or reduces the projected image.
Note
Press
×1 ×2 ×3 ×4 ×9
Press .
You can change the location of the
• enlarged image using P, R, O and Q.
Press RETURN on the remote
2
control to cancel the operation.
The magnifi cation then returns to u1.
Note
The selectable magnifi cations differ depending on the input signal. This function is not available for the 3D
• mode. In the following cases, the image will
• return to the normal size (u1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When switching “DLP
between “On” and “Off”.
or MAGNIFY enlarges
.
®
LinkTM”
Features
Useful
41
Operating with the Remote Control (Continued)

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.
Connecting with a USB cable
Computer
To USB terminal
USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)
The mouse pointer can be operated in the following way after it is connected.
When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
When left-clicking
Press L-CLICK.
When right-clicking
Press R-CLICK.
When your computer supports only a one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.
When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE D OWN.
To USB terminal
MOUSE/Adjustment
MOUSE/Adjustment buttons (//?/_)
buttons (//?/_)
R-CLICK button
R-CLICK button
L-CLICK button
L-CLICK button
PAGE UP/
PAGE UP/ PAGE DOWN buttons
PAGE DOWN buttons
Note
This function only works with the Microsoft® Windows® OS and Mac OS® that support USB.
• You cannot use this function when displaying the menu screen.
• Confi rm that the computer recognizes the USB connection.
42

Menu Items

The following shows the items that can be set in the projector.
“Picture” menu
Main menu Sub menu
Picture
Picture Mode
Page 48 Page 48
Contrast
Bright
Color
Tint
Sharp
Red
Blue
Standard Presentation Movie Game sRGB
+30-30
+30-30
+30-30
+30-30
+30-30
+30-30
+30-30
Page 48
CLR Temp
+2-2
Page 49
BrilliantColor™
20
Page 48
C.M.S.1 Select Color
Page 49
C.M.S.2 Select Color
Page 49
DNR Off
Page 50
Eco+Quiet
[On/Off]
Hue
Saturation
Valu e
Effect
C.M.S.1 [On/Off]
Reset
Return
Hue
Saturation
Valu e
Effect
C.M.S.2 [On/Off]
Reset
Return
Level 1 Level 2 Level 3
Page 50
Reset
“Audio” menu
Main menu Sub menu
Audio
Speaker
[On/Off]
Page 51 Page 51
Audio Input Audio1
Page 51
Audio Out FAO
Page 51
Treble
Audio2 HDMI
VAO
+30-30
Page 51
Bass
+30-30
Page 51
Features
Useful
43
Menu Items
(Continued)
“Signal adjustment (SIG)” menu
Main menu Sub menu
SIG
Page 52
Clock
Phase
H-Pos
V-Pos
Reset
+150-150
+30-30
+150-150
+60-60
Page 52
Resolution
Page 52
Auto Sync [On/Off]
Page 52
Signal Type
Page 52
Video System Auto
Page 53
Video Setup
Page 53
Dynamic Range Auto
Page 53
Signal Info
Auto RGB YPbPr
PAL SECAM NTSC4.43 NTSC3.58 PAL -M PAL -N PAL-60
0 IRE
7.5 IRE
Standard Enhanced
Page 53
“Screen adjustment (SCR)” menu
Main menu Sub menu
SCR
Page 54
Resize
Page 54
Wall Color Off
Page 54
Overscan [On/Off]
Normal Full Native Area Zoom V-Stretch Border 16:9
Blackboard Whiteboard
Page 54
OSD Display [On/Off]
Page 54
Closed Caption
Page 55
Background
Page 55
PRJ Mode
Page 55
Language
Page 55
Off CC1 CC2
Logo Blue None
Front Ceiling + Front Rear Ceiling + Rear
English Deutsch Español Nederlands Français Italiano Svenska Português
polski Magyar Türkçe
Tiếng Việt
44
“Projector adjustment (PRJ)” menu
Main menu Sub menu
PRJ
Page 56
Auto Power Off [On/Off]
Page 56
Auto Restart [On/Off]
Page 56
COMPUTER2 Select
Page 56
STANDBY Mode
Page 56
RS-232C
Page 56
Fan Mode
Page 57
System Lock [Enable/Disable]
Input Monitor Output
Standard Eco
9600bps 38400bps 115200bps
Normal High
Page 57
DLP® Link™ [On/Off]
Page 58
DLP® Link™ Invert
Page 58
Memory Menu
Page 59
Rotate Indicator [On/Off]
Page 59
All Reset
Page 60
Lamp Timer (Life)
Page 60
Load Memory
Page 59
Save Memory
Page 59
Memory Name
Page 59
Clear Memory
Page 59
Mute [On/Off]
Memory1
Memory2
Memory3
Memory4
Memory5
Memory6
Memory7
Memory8
Page 59
Memory Lock [On/Off]
Page 59
Return
“Network (Net.)” menu
Main menu
Net.
Page 61
Password [Enable/Disable]
Page 61
DHCP Client [On/Off]
Page 62
TCP/IP
Page 62
Reset Network Setting
Page 62
Restart Network
Page 62
IP Address
Page 63
MAC Address
Page 63
Projector
Page 63
Sub menu
IP Address Subnet Mask Gateway
Features
Useful
45

Using the Menu Screen

2
RETURN button
Press RETURN to return to the
• previous screen when the menu is displayed.
ENTER button
Adjustment buttons (P/R/O/Q)
MENU button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.
MENU button ENTER button
Adjustment buttons (P/R/O/Q)
RETURN button
Press RETURN to return
• to the previous screen when the menu is displayed.
Press MENU.
1
The “Picture” menu screen for the selected
• input mode is displayed.
Press Q or O and select
2
“Picture” to adjust.
46
Example: “Picture” screen menu
Menu item
Picture Audio SIG SCR PRJ Net.
Picture Mode
Contrast 0 Bright Color Tint
Red Blue CLR Temp BrilliantColor C.M.S.1 C.M.S.2 DNR Eco+Quiet
Reset
SEL./ADJ. RETURN
TM
0 0 0 0Sharp 0 0
0 1
Standard
Off
Off Level 2 Off
ENTER END
Press P or R and select “Bright”
3
5
3
to adjust.
The selected item is highlighted.
Picture Audio SIG SCR PRJ Net.
Picture Mode
Contrast 0
Bright
Color Tint
Red Blue CLR Temp BrilliantColor C.M.S.1 C.M.S.2 DNR Eco+Quiet
Reset
SEL./ADJ. RETURN
TM
0
0 0 0Sharp 0 0 0 1
Standard
Off
Off Level 2 Off
ENTER END
Items to be adjusted
Picture Audio SIG SCR PRJ Net.
To adjust the projected image while watching it
Press ENTER.
The selected item (e.g. “Bright”) is
Clock Phase H-Pos V-Pos
Reset
displayed by itself at the bottom of the screen. When pressing P or R, the following item
• (“Color” after “Bright”) will be displayed.
Note
Press ENTER again to return to the
• previous screen.
Press O or Q to adjust the item
4
selected.
The adjustment is stored.
Press MENU.
5
The menu screen will disappear.
The item displayed by itself
Picture
SEL./ADJ. RETURN
Picture Audio SIG SCR PRJ Net.
Picture Mode
Contrast 0
Bright
Color Tint
Red Blue CLR Temp BrilliantColor C.M.S.1 C.M.S.2 DNR Eco+Quiet
Reset
SEL./ADJ. RETURN
Note
The MENU button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute
0 0 0 0
Press ENTER.
0Bright
ENTER END
Standard
15
0 0 0Sharp 0 0
TM
0 1
Off
Off Level 2 Off
ENTER END
Features
Useful
47

Picture Adjustment (“Picture” Menu)

Menu operation n Page 46
Picture Audio SIG SCR PRJ Net.
Picture Mode
Contrast 0 Bright Color
Tint
Red Blue
CLR Temp BrilliantColor
C.M.S.1
C.M.S.2 DNR
 
Eco+Quiet
Reset

Selecting the Picture Mode

1
SEL./ADJ. RETURN
TM
Selectable
items
Standard
0 0 0 0Sharp 0 0
0 1
Off
Off Level 2 Off
ENTER END
Description
Standard For standard image Presentation
Movie Gives natural tint to the projected
Game Gives sharpness to the projected
*sRGB For high fi delity reproduction of
“sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture”
Brightens portions of image for more enhanced presentations.
image.
image.
images from a computer.
menu to your preference. Any changes you make are retained in memory.
Note
You can also press PICTURE MODE on the
• remote control to select the picture mode. (See page *sRGB is an international standard of color
41.)
reproduction regulated by the IEC (International Electrotechnical Commission). As the fi xed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when “sRGB” is selected. For additional information about the sRGB function, visit “http://www.srgb.com/”. You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Brilliant Color “C.M.S.2”, when “sRGB” is selected.
TM
”, “C.M.S.1” and
Info
When “sRGB” is selected, the projected image
• may become dark, but this does not indicate a malfunction.

Adjusting the Image

2
Adjustment
items
Contrast For less
Bright For less
1
Color*
1
Tint*
Sharp For less
1
Red*
1
Blue*
BrilliantColor™*1*2For making the
*1 Not adjustable/selectable when selecting “sRGB”. *2 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™ level is increased, the image becomes brighter while the color reproduction is kept at a high level.
Note
“Color”, “Tint”, “Red”, “Blue”, “BrilliantColorTM” and “CLR Temp” cannot be set when “sRGB” is selected. To reset all adjustment items, select “Reset”
• and press ENTER.
O button Q button
contrast.
brightness. For less color
intensity. For making skin
tones purplish.
sharpness. For weaker red. For stronger
For weaker blue.
effect weaker.
For more contrast.
For more brightness.
For more color intensity.
For making skin tones greenish.
For more sharpness.
red. For stronger
blue. For making the
effect stronger.
48
Adjusting the Color

Temperature
Selectable
items
For lower color temperature for warmer, reddish incandescent-like
–2
images.
0
+2
For higher color temperature for cooler, bluish, fl uorescent-like images.
Note
Values on “CLR Temp” are only for general standard purposes. “CLR Temp” cannot be set when “sRGB” is
• selected.

Adjusting the Colors

4
You can select the color of the projected image to correct and then adjust it to the desired color by setting “Hue”, “Saturation”, “Value”, and “Effect”.
Note
Before performing this adjustment, prepare the image to be adjusted. You can perform this adjustment easier in the
• still image than in the moving image.
Select “C.M.S.1” or “C.M.S.2”
1
(C.M.S.: Color Management System), and press ENTER.
If there is no data for the stored corrected
• color, the color selection screen and the picker is displayed. (Go to step 2.)
Description
Menu operation n Page 46
If there is data for the stored corrected color, the C.M.S. color adjustment screen is displayed. (Go to step 3.)
C.M.S.1
Select Color
0
Hue Saturation
0 0
Value
0
Effect C.M.S.1 On
Reset Return
SEL./ADJ.
ENTER
RETURN
END
Use the picker and select the
2
color of the projected image to correct. The picker can be operated by adjustment buttons (P/R/O/Q) on the remote control.
By enlarging the projected image using
or MAGNIFY, more fi ne
adjustment can be performed.
By continuing to press the adjustment buttons (P/R/O/Q), the picker moves rapidly.
After selecting the color of the projected image to correct, press ENTER. The C.M.S. color adjustment screen is displayed. (Go to step 3.)
Picker
Features
Useful
Picker
49
3
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation n Page 46
Set or adjust each item in the
3
C.M.S. color adjustment screen.
C.M.S.1
Select Color
0
Hue Saturation
0 0
Value
0
Effect C.M.S.1 On
Reset Return
SEL./ADJ.
ENTER
RETURN
END
C.M.S. color adjustment screen:
Selectable items
Select Color Starts over the selection of
Hue Sets the hue of the main
Saturation Sets the saturation of the
Value Sets the value of the main
*1
Effect
*2
C.M.S.1 (or C.M.S.2)
Reset Sets “Hue”, “Saturation”,
Return Completes the correction
*1 To specify the range of color correction,
select “Effect” and press
O button Specifi es smaller range. Q button Specifi es larger range.
*2 To check the appearance of the projected
image, select “C.M.S.1” (or “C.M.S.2”) and set to “On” or “Off”.
On The appearance of the
Off The appearance of the pro-
Description
the color to be corrected.
colors.
main colors.
colors. Specifi es the range of color
correction. Checks the appearance of
the projected image after above correction.
“Value”, and “Effect” to their default values.
and closes the C.M.S. color adjustment screen.
O or Q button.
projected image after above color adjustment refl ected can be checked.
jected image in former color adjustment can be checked.
To complete the C.M.S. color
4
adjustment, select “Return” and press ENTER.
Note
The C.M.S. color adjustment can be made to one color each in “C.M.S.1” and “C.M.S.2”. “C.M.S.1” and “C.M.S.2” cannot be set when
• “sRGB” is selected.

Reducing Image Noise (DNR)

5
Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Selectable
items
Off The DNR function is not activated. Level 1 Level 2 Level 3
Sets the DNR level for viewing a clearer picture.
Note
Set “DNR” to “Off” in the following cases:
When the image is blurry.
When the contours and colors of moving images drag. When TV broadcasts with weak signals are
• projected.

Eco+Quiet

6
Selectable
items
Brightness
On Approx. 80% Low Approx.
Off 100% Normal Approx.
Note
You can also use ECO+QUIET on the remote control or on the projector to switch the Eco+Quiet mode. (See page
Description
Fan
Sound
40.)
Lamp life
2,500 hours
1,5 00 hours
50

Audio Adjustment (“Audio” Menu)

Picture Audio SIG SCR PRJ Net.
Speaker

Audio Input

Audio Out
Treble
Bass
SEL./ADJ. RETURN
Speaker Settin
1
On Audio1
FAO 0 0
ENTER END
g
This function allows you to set the audio output of the internal speaker to “On” or “Off” such as when the projector is connected to an external amplifi er.
Selectable
items
On The audio signal is output from the
Off The audio signal is not output from the
2
internal speaker.
internal speaker.
Audio Input
Description
This function allows you to select an appropriate combination of audio input terminals for each input mode.
Selectable
items
Audio 1 The AUDIO 1 input terminal is used as
Audio 2 The AUDIO 2 input terminal is used as
HDMI HDMI terminal is used as an audio
an audio input terminal
an audio input terminal.
input terminal. (This item is available with HDMI input.)
Description

Audio Output Type Setting

3
This function determines whether the audio level output from the AUDIO output terminal is fi xed or variable by linking with VOLUME.
Selectable
items
FAO (Fixed Audio Output)
VAO (Variable Audio Output)
Audio output that does not vary in strength with the volume level of the source projector.
Audio output that varies in strength with the volume level of the source projector.
Info
When “Audio Out” has been set to “VAO”, fi rst
• make sure to lower the volume of the projector before turning the power on or off and when switching the input.

Adjusting the Audio

4
This function allows you to adjust the projector’s audio.
Selectable
items
Treble For weaker treble For stronger treble Bass For weaker bass For stronger bass
O button Q button
Menu operation n Page 46
Description
Features
Useful
51

Signal Adjustment (“SIG” Menu)

Picture Audio SIG SCR PRJ Net.
Clock Phase
H-Pos V-Pos
Reset
Resolution Auto Sync
Signal Type
Video System
Video Setup
Dynamic Range
1
Signal Info : 1024 x 768
H 48.3 kHz / V 60.0 Hz
SEL./ADJ. RETURN

Adjusting the Computer Image

0 0 0 0
1024 x 768 On
Auto Auto 0 IRE Standard
ENTER END
If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG function.
Selectable
items
Clock Adjusts vertical noise. Phase Adjusts horizontal noise (similar to
H-Pos Centers the on-screen image by
V-Pos Centers the on-screen image by
tracking on your VCR).
moving it to the left or right.
moving it up or down.
Description
Note
To reset all adjustment items, select “Reset” and press ENTER. The adjustable range of “H-Pos” (H-Position)
• and “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.

Auto Sync Adjustment

3
Used to automatically adjust a computer image.
Selectable
items
On Auto Sync adjustment will occur when
Off Auto Sync adjustment is not
the projector is turned on or when the input signals are switched, when connected to a computer.
automatically performed.
Note
Auto Sync adjustment is also performed by pressing AUTO SYNC on the projector or on the remote control.
The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the pro jector.

Signal Type Setting

4
This function allows you to select the input signal type RGB or Component for COMPUTER/COMPONENT 1, 2.
Selectable
items
Auto Input signals are automatically
RGB Set when RGB signals are received. YPbPr Set when Component signals are
recognized as RGB or component.
received.
Menu operation n Page 46
Description
Description

Resolution Setting

2
Ordinarily, the type of input signal is detected and the correct Resolution mode is automatically selected. However, for some signals, the optimal Resolution mode in “Resolution” may need to be selected to match the computer display mode.
Note
See “Checking the Input Signal” on page 53 for information on the currently selected input signal.
52
Menu operation n Page 46

Setting the Video System

5
The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference. In that case, switch the Video signal.
Selectable items
Auto PAL SECAM *NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60
* When reproducing NTSC signals in PAL video
equipment.
Note
The Video signal can only be set in VIDEO or S-VIDEO mode.
When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

Setting the Video Setup

6
Selectable
items
0 IRE Sets the black level to 0 IRE.
7.5 IRE Sets the black level to 7.5 IRE.
Description

Selecting the Dynamic Range

7
An optimum picture may not be displayed if an HDMI capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.
Selectable
items
Auto When the black levels of the image Standard Enhanced
The Dynamic Range can be selected only
• when “HDMI” input mode is selected.
8
This function allows you to check the current input signal information.
show banding or appear faded, select the item that results in the best picture quality. (In most circumstances, “Standard” should be selected.)
Note

Checking the Input Signal

Description
Note
This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:
I
- 480 With S-VIDEO or VIDEO input:
- NTSC3.58
Features
53
Useful

Screen Adjustment (“SCR” Menu)

Picture Audio SIG SCR PRJ Net.
Resize
Wall Color
Overscan
OSD Display
Closed Caption
Background
PRJ Mode
Language
SEL./ADJ. RETURN

Setting the Resize Mode

1
Normal Off On
On
Off Logo Front
English
ENTER END
Note
For details of the Resize mode, see pages 36
• to 39. You can also press RESIZE on the remote
• control to set the resize mode. (See page

Selecting the Wall Color

2
36.)
This function allows you to project the image to a colored (white or dark green) surface or wall without using a screen.
Selectable items Description
Off The Wall Color function is not
Blackboard
Whiteboard
activated. Projects images onto a
blackboard (dark green). Projects images onto a
whiteboard.

Setting the Overscan

3
This function allows you to set the overscan area (display area).
Selectable
items
On The input area is displayed without the
Off The whole input area is displayed.
screen edges.
Note
This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:
- 480P
- 540P
- 576P
- 720P
- 1035I
- 1080I/1080P If noise appears at the screen edges when
• “Off” is selected, set the function to “On”. Also see “About Copyrights” on page
Setting the On-screen
4
Display
This function allows you to turn the on-screen messages on or off.
Selectable
items
On All On-screen Displays are displayed. Off
INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ ECO+QUIET/MAGNIFY/ “An invalid button has been pressed.” are not displayed.
Menu operation n Page 46
Description
39.
Description
54

Closed Caption

5
<For Americas only>
Info
This function is available for NTSC3.58 signal.
• This function may not work depending on the
• resize mode.
“Closed Caption” is a system which allows
• conversations, narration, and sound effects in TV programs (Limited regions) and home videos to be viewed as captions on the screen. Not all programs and videos will offer closed
• captioning. Please look for the symbol to ensure that captions will be shown. Two channels are available: CC1 and CC2.
Selectable
items
Off — CC1 Closed Caption mode for CH1 data CC2 Closed Caption mode for CH2 data
Note
Closed Caption may malfunction (white blocks,
• strange characters, etc.) if signal conditions are poor or if there are problems at the broadcast source. This does not necessarily indicate a problem with the projector.
Description
Menu operation n Page
Selecting a Startup
6
and Background Image
Selectable
items
Logo SHARP default image Blue Blue screen None Black screen
Reversing/Inverting
7
Description
Projected Images
This projector is equipped with a reverse/ invert image function that allows you to reverse or invert the projected image for various applications.
Selectable
items
Front Normal image (Projected from the
Ceiling + Front Inverted image (Projected from the
Rear Reversed image (Projected from
Ceiling + Rear Reversed and inverted image
front of the screen)
front of the screen with an inverted projector)
the rear of the screen or with a mirror)
(Projected with a mirror)
Description
46
Note
Refer to “Projection (PRJ) Mode” on page
• for details.
Selecting the On-screen
8
Display Language
The projector can switch the on-screen display language among 18 languages.
21
Features
55
Useful

Helpful Functions Set during Installation (“PRJ” menu)

Menu operation n Page 46
Picture Audio SIG SCR PRJ Net.
Auto Power Off
Auto Restart

COMPUTER2 Select

STANDBY Mode

RS-232C
Fan Mode
Sysem Lock
®
DLP
Link™
®
DLP
Link™ Invert
Memory Menu
 T
Rotate Indicator
All reset
Z
Lamp Timer (Life) [ 0]h [ 0] min ( 100%)
H
SEL./ADJ. RETURN

Auto Power Off Function

1
Selectable
items
On The projector automatically enters
Off The Auto Power Of f function will
the standby mode when no input signal is detected for 15 minutes or longer.
be disabled.
On
On Monitor Output Standard 9600bps Normal Disable
Off
On
ENTER END
Description
Note
When the Auto Power Off function is set to
• “On”, 5 minutes before the projector enters the standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

Auto Restart Function

2
Selectable
items
On If the power cord is unplugged
Off The projector does not turn on
from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.
automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.
Description
COMPUTER2 Select
3
You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. Select whether to use the terminal as an input terminal or output terminal.
Selectable items Description
Input The terminal can be used as an
Monitor Output The terminal can be used as an
input terminal (COMPUTER/ COMPONENT 2).
output terminal (MONITOR OUT).
Note
Set this before connecting the external equipment. The setting cannot be changed when Input
• mode is “COMPUTER 2”.
STANDBY Mode
4
When set to “Eco”, power consumption is reduced in Standby mode.
Selectable items
Eco The monitor output, RS-232C and
Standard The monitor output, RS-232C and
5
Network functions are switched off in Standby mode.
Network functions are activated even if the projector is in Standby mode.
Selecting the Transmission
Description
Speed (RS-232C)
Make sure that both the projector and com­puter are set for the same baud rate.
Selectable items
9600 bps 38400 bps 115200 b ps
Note
Refer to the “SETUP MANUAL” contained on
• the supplied CD-ROM for RS-232C Specifi cations and Command Settings. Refer to the computer’s operation manual for
• instructions for setting the computer’s baud rate.
Description
Transmission speed is slow.
Transmission speed is rapid.
56
3
Menu operation n Page 46

Fan Mode Setting

6
This function changes the fan rotation speed.
Selectable
items
Normal Suitable for normal environments. High Select this when using the
When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

System Lock Function

7
This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest
you record the keycode in a safe place where only authorized users have access.
projector at altitudes of approximately 1,500 meters (4,900 feet) or more.
Description
Info
If you lose or forget your keycode, contact your
• nearest Sharp Authorized Projector Dealer or Service Center (see page warranty is valid, the keycode reset will incur a charge.
a
Setting/Changing the keycode
Select “System Lock”, then press
1
ENTER or Q.
Select “Next”, then press ENTER.
2
The screen for entering the keycode
• appears.
84). Even if the product
Press the 4 buttons on the remote
3
control or on the projector to enter the preset keycode in “Old Code”.
When setting the keycode for the fi rst time,
• press R on the projector for four times.
Setting the System Lock
Old Code
New Code Reconfirm
Note
If you input a wrong keycode, the
• cursor returns to the fi rst point of the “Old Code”. The preset keycode is 4 R buttons on
• the projector. When you press the R button four times, the keycord input screen disappears.
Press the 4 buttons on the remote
4
4
control or on the projector to enter
PRJ
––––
–––– ––––
the new keycode in “New Code”.
Note
You cannot use the following buttons
• for keycode:
STANDBY, ENTER , L-CLICK/EFFECT, R-CLICK/RETURN, MENU, ECO+QUIET, BREAK TIMER, ZOOM, FOCUS, H&V SHIFT, ROTATE, LENS, MEMORY MENU and MEMORY (1-8) System lock function recognizes
• each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in set ting your keycode, the keycode cannot be canceled with the remote control.
STANDBY/ON, ON,
Features
Useful
Setting the System Lock
Old Code
New Code
Reconfirm
PRJ
****
– ––––
–––
57
5
Helpful Functions Set during Installation (“PRJ” menu) (Continued)
Enter the same keycode in “Re-
5
confi rm”.
Note
To cancel the keycode that you have already set
Press R on the projector for four times in
• steps 4 and 5 above.
When the System Lock is set
When System Lock is set, the keycode input
• screen appears after the power is turned on. When it appears, enter the right keycode to start projection.
Input screen for keycode
System Lock
––––
Taking the Keylock Off
Hold down ENTER on the projector for about 5 seconds.
On-screen display
Info
Even when Keylock function is set to “On”, STANDBY/ON on the projector can be used to turn on and off the power.
Keylock cannot be set while the projector is: displaying the “Menu” screens, in Standby mode, warming up, changing input signals, operating the Auto Sync function, in Freeze mode or on the “System Lock” screen during warming up.
Menu operation n Page 46

Keylock Function

Use this function to lock the operation buttons on the projector.
Locking the Operation Buttons
Hold down ENTER on the
1
projector for about 5 seconds while the projector is being turned on.
The Keylock function screen is displayed.
Use this function to lock the operation buttons on the projector. (Except STANDBY/ON button)
Note: You can release the keylock by holding down ENTER on the projector for about 5 seconds.
Return
On
SEL./ADJ. RETURN
Select “On”, then press
2
On-screen display
The Keylock function does not affect the operation with the remote control buttons. You cannot use the Keylock function while the
• projector is warming up.
ENTER END
ENTER
.
DLP® Link
8
See “Using 3D Viewing Mode” on page 67 for details.

DLP® LinkTM Invert

9
See “Using 3D Viewing Mode” on page 67 for details.
TM
58

Memory Menu

0
You can store the settings of the projector's lens shift (ZOOM, FOCUS) and others (such as INPUT, PICTURE MODE, RESIZE, Wall Color, PRJ Mode and KEYSTONE), or activate the stored settings. You can also store the rotation angle when attaching the ceiling-mount rotating module (AN-SV100T) to the projector. The Memory Menu screen can also be displayed by pressing MEMORY MENU on the remote control.
aLoad Memory
To activate the desired settings, select the item where the settings are stored.
Note
Pressing any button while the projector is in the process of activating the “Load Memory” function will display messages: – “STOP”: stops the activation of the “Load
Memory” function.
– “CONTINUE”: allows the projector to the
already set position.
– “Return to the initial position.”: let the
projector go back to the initial position.
The confi rmation screen of “Load Memory” will also be displayed by pressing MEMORY
(1-8) on the remote control. Press MEMORY (1-8) again to perform the “Load Memory”
function.
The memory has a margin of error of approximately ±2% (When the ceiling-mount rotating module (AN-SV100T) is attached, allow a margin of error of approximately ±1.5 degrees). Use the remote control to make fi ne adjustments.
aSave Memory
Select an item where you want to store the setting.
Note
When you select an item where some setting has been stored, the stored setting will be overwritten and erased.
aMemory Name
Select the item name you want to change. Use
O/Q to choose the characters to change, and P/R to select the characters to enter.
Menu operation n Page 46
aClear Memory
Select the item where the settings you want to erase are stored. In this case, the memory name you have changed returns to the default setting.
Note
Selecting “All Clear” erases all the stored
• settings.
aMute
Selectable
items
On Does not display images while the
Off Displays images while the projector
projector is in the process of activating the “Load Memory” function.
is in the activation process.
Description
aMemory Lock
Selectable
items
On Protects the stored memories. Off Does not protect the stored
memories.

Rotate Indicator

This function turns On/Off the Rotate indicator on the projector.
Selectable
items
On The Rotate indicator lights up when
Off The Rotate indicator does not light
Note
This function only works when attaching the
• ceiling-mount rotating module to the projector.
the ceiling-mount rotating module (AN-SV100T) is connected. While the projector is rotating, the indicator blinks.
up.
Description
Description
Features
59
Useful
Helpful Functions Set during Installation (“PRJ” menu) (Continued)
Returning to the Default
Settings
This function allows you to initialize the set­tings you have made in the projector.
Note
The following items or menu cannot be initialized.
“SIG” menu Resolution
“SCR” menu Language
“PRJ” menu Lamp Timer (Life) System Lock COMPUTER2 Select Memory Menu
Checking the Lamp
Life Status
You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).
Lamp usage condition Remaining lamp life
“Life” 100% 5%
Operated exclusively while “Eco+Quiet” is “On”.
Operated exclusively while “Eco+Quiet” is “Off”.
Approx. 2,500 hours
Approx. 1,500 hours
Approx. 125 hours
Approx. 75 hours
Menu operation n Page 46
Note
It is recommended that the lamp be changed when the remaining lamp life becomes 5%. The lamp life may vary depending on the
• usage condition.
60
3
4
2
3

Setting Up the Projector Network Environment (“Net.” Menu)

Menu operation n Page 46
Picture Audio SIG SCR PRJ Net.
Password
DHCP Client
 
TCP/IP
Reset Network Setting
 
Restart Network
IP Address XXX.XXX.XXX.XXX MAC Address XX:XX:XX:XX:XX:XX
Projector XX-XXXX
SEL./ADJ. RETURN

Setting a Password

1
If you do not want others to change the setting for the “Net.” menu, set a password.
a
Setting a Password
Select “Password”, then press Q.
1
The screen for entering the password
• appears.
Setting the Password
Old Password
New Password
Reconfirm
Press P or R to set the fi rst digit
2
2
in “New Password”, then press Q.
Enter the remaining 3 digits, then
3
press ENTER.
To return to the previous digit, press O.
Enter the same password in
4
“Reconfi rm”, then press ENTER.
The status for “Password” changes to
• “Enable”.
Disable Off
ENTER END
–––
–––
––––
Net.
a
Changing the Password
Select “Password”, then press Q.
1
The screen for entering the password
• appears.
Enter the password in “Old
2
Password” using P, R, Q and O, then press ENTER.
Enter the password in “New
3
Password” using P, R, Q and O, then press ENTER.
Enter the same password again
4
in “Reconfi rm” using P, R, Q and O, then press ENTER.
Note
If you do not need the password protection for the “Net.” menu settings anymore, press ENTER without entering new password in steps 3 and 4.
To cancel the password settings, press
RETURN.
If you forget the password
If you forget the password, perform the following procedure to delete it, then set a new password.
On the projector, press
Note
If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page You cannot use the buttons on the
• remote control to delete the password.
58.)
.
Features
Useful
Note
Once after the password is set, you must enter the password to change the “Net.” menu settings.
61
3
4
5
Setting Up the Projector Network Environment (“Net.” Menu (Continued)

DHCP Client Setting

2
Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work.
Selectable items Description
On Obtains confi guration
Off Sets the TCP/IP manually.
Select “On” for “DHCP Client”. “Obtaining IP Address...” appears, then the menu screen appears. Confi rm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen. If the DHCP server is not available, “Could not obtain IP Address.” appears. In this case, set the TCP/IP manually. (See the item 3.)

TCP/IP Setting

3
Set the TCP/IP manually.
Select “Off” for “DHCP Client”,
1
then press ENTER.
Select “TCP/IP”, then press
2
ENTER.
Enter “IP Address” using P, R, Q
3
and O, then press ENTER.
Setting the TCP/IP
IP Address
Subnet Mask Gateway
parameters for TCP/IP network automatically.
Net.
1
92 .
1
68 .
1
50 .
0
55 .2
000 .
55 .2
000 .
55 .2
000 .
02
000
000
Selectable items Description
IP Address Factory default setting:
Subnet Mask Factory default setting:
Gateway Factory default setting: 000. 000.
Note
Confi rm the existing network’s segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192.168.150.002” is not used in a network with an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address.
For details about each setting, consult your network administrator.
Returning to Default
4
Settings (Network)
This function allows you to initialize the Network settings you have made in the projector.
Note
If the values for IP Address, Subnet Mask or Gateway of the projector have been returned to the default settings, the computer cannot be connected to the projector depending on the computer’s network settings.
Menu operation n Page 46
192.168.150.00 2 Enter an IP address appropriate for the network.
255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network.
000. 000 * When not in use, set to “000.
000. 000. 000”.
)
Enter “Subnet Mask” using P, R,
4
Q and O, then press ENTER.
Enter “Gateway” using P, R, Q
5
and O, then press ENTER.
62

Restart Network Function

5
Restarts the network function. Perform this function when the projector cannot be controlled via the network.
Confi rming the
6
Projector Information
You can confi rm the following items.
Menu operation n Page 46
Selectable
items
IP Address The IP address of the projector is
MAC Address The MAC address of the projector is
Projector The projector name is displayed.
Note
For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM.
displayed.
displayed.
Description
Features
63
Useful

Viewing Stereoscopic 3D Images

Precautions on Viewing Stereoscopic 3D Images

Before viewing stereoscopic 3D images, please read this section carefully.
WARNING
Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would normally view your screen. However, some people may experience discomfort. The following precautions are recommended to minimize the potential for experiencing visual problems or any adverse symptoms.
Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D viewing.
* Based on the guidelines issued by the 3D Consortium revised December 10, 2008.
Maintain an appropriate distance from the screen. Viewing from too close a distance can strain your eyes. If you experience eye strain, immediately discontinue viewing.
If you experience any of the following symptoms during viewing: – nausea – queasiness/dizziness – headache – blurry vision or double vision that lasts longer than few seconds Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and do not resume stereoscopic 3D viewing without discussing your symptoms with a physician.
As you get more comfortable viewing stereoscopic 3D:
• Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the parallax on some models of equipment.)
• Adjust the projected image to the most comfortable viewing size by zooming.
(Projecting images on the smallest or largest screen size possible may eliminate the
stereoscopic effect and strain your eyes.)
• Use the DLP (For details on using “DLP® Link™ Invert”, see the section on its operation in this operation manual.)
®
Link™ Invert function to properly set the video for your left and right eyes.
64
WARNING
The following people should limit stereoscopic 3D viewing: – Children under 6 years of age (to protect the eye growth process) – People with a history of photosensitivity – People with heart disease – People in poor health – People who are sleep deprived – People who are physically tired – People under the influence of drugs or alcohol
Epilepsy
A small percentage of the population may experience epileptic seizures when viewing certain types of images that contain fl ashing patterns of light.
IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY
The following people should consult a physician before viewing stereoscopic 3D images. – Anyone with a history of epilepsy, or who has a family member with a history of
epilepsy – Children under 6 years of age – Anyone who has ever experienced epileptic seizures or sensory disturbances triggered
by fl ashing light effects
SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY
Discontinue use if you experience any of the following symptoms while viewing stereoscopic 3D images. – Involuntary movements, eye or muscle twitching – Muscle cramps – Nausea, dizziness, or queasiness – Convulsions – Disorientation, confusion, or loss of awareness of your surroundings
Features
65
Useful
Viewing Stereoscopic 3D Images (Continued)

Information on the 3D Projection Function

To display 3D images, this projector requires:
WHAT YOU WILL NEED
1) Source devices that support the field sequential format – For details on the supported signals, see the Compatibility Chart in this operation
manual.
2) 3D LCD shutter glasses that support the DLP – Contact your nearest Sharp Authorized Projector Dealer for purchasing details. * DLP® Link™ is a trademark of Texas Instruments.
The projected image may become dark when using the 3D projection function (with “DLP Link™ ” set to “On”).
When “DLP available at all.
– Keystone – Resize – Magnify
3D formats except for the field sequential method, such as ones used for Blu-ray 3D or DVD prepackaged media, are not compatible with this projector. (As of February 2011)
If the power of your left and right eyes greatly differs and you primarily use one eye for viewing the images, the images will not appear in 3D.
In addition, images may be difficult to view in 3D or images may not be able to be viewed in 3D depending on the individual or the content being displayed. The stereoscopic effect varies with the individual.
3D viewing is possible within the range that the 3D LCD shutter glasses are able to receive light signals reflected by the screen. However, most 3D images are manufactured to be viewed from directly in front of the screen, so 3D viewing is recommended directly in front of the screen as much as possible.
– The range for receiving signals varies depending on the 3D LCD shutter glasses. For
details, see the operation manual of your 3D LCD shutter glasses.
3D images may not be able to be played back correctly on your computer.
®
Link™” is set to “On”, the following functions may not work fully or may not be
®
Link™* system
®
66

Using 3D Viewing Mode

3
5
6
8
9
3
Use the following procedure to project 3D images.
For operation of the 3D LCD shutter glasses and the 3D-video playback equipment, see the corresponding operation manual.
O/Qbuttons
ENTER button
3D MODE button
Projecting 3D images
Turn the projector on.
1
Turn the 3D-video playback
2
equipment on.
Set the 3D-video playback equipment so
• that it outputs one of the signals listed in the Compatibility Chart in this operation manual.
Switch the Input mode of the
3
projector to enable input of 3D video signals.
Operate the 3D-video playback
4
equipment and play back the 3D content.
Press 3D MODE on the remote
6
control to display the 3D MODE menu.
Info
If “An invalid button has been pressed.” is displayed, a 3D-compatible signal is not being input. Check the output signal on the playback equipment.
Press Q to set “DLP® Link™” to
7
“On”.
Press ENTER to switch the mode
8
and enable more natural 3D image viewing.
Warning!
If the projector, 3D-video playback
• equipment, and 3D LCD shutter glasses are not properly set, you may experience eye strain in addition to not being able to view the images in 3D.
Press 3D MODE.
9
The 3D MODE menu will disappear.
Note
If the images are not displayed in 3D, repeat
• steps 6 to 8. You can also use “DLP
• Link™ Invert” on the menu screen to change the 3D setting.
®
Link™” and “DLP
Ending 3D projection
Press 3D MODE on the remote
1
1
control to display the 3D MODE menu.
®
Features
Useful
Turn the 3D LCD shutter glasses
5
on and place them over your eyes.
Press O to set “DLP® Link™” to
2
“Off”.
Press 3D MODE.
3
The 3D MODE menu will disappear.
67
Viewing Stereoscopic 3D Images (Continued)

Appendix

How the 3D Projection Function (DLP Link™ ) Works
The 3D projection function of this projector is compatible with the DLP® Link™ system. To watch 3D images, you use a pair of 3D LCD shutter glasses that alternately display the projected images for the left and right eyes and are synchronized with a control (light) signal.
Shutter glasses
control light signal*
* The control light signal is transmitted from the lens of the projector, refl ected by the screen,
and received by the light reception sensor on the 3D LCD shutter glasses. Therefore, the range of 3D viewing varies depending on the specifi cations of the 3D LCD shutter glasses (light signal receiving sensitivity).
For details, see the operation manual of your 3D LCD shutter glasses.
For more information on the 3D projection function
Future information on the 3D projection function will be posted on the following web site. http://www.sharp-world.com/projector/
68

Maintenance

Cleaning the projector
Ensure that you have unplugged the power
cord before cleaning the projector. The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or thinner, as these can damage the fi nish on the cabinet. Do not use volatile agents such as
insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or fi nish of the projector. Wipe off dirt gently with a soft fl annel cloth.
Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the cabinet or cause cracking. Wiping with a hard cloth or using strong
force may scratch the cabinet surface. When the dirt is hard to remove, soak a cloth
in a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.
Mild detergent
Cleaning the lens or lens cover
Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses) for cleaning the lens or lens cover. Do not use any liquid type cleaning agents, as they may wear off the coating fi lm on the surface of the lens or lens cover. As the surface of the lens or lens cover can
easily get damaged, be careful not to scrape or hit the lens or lens cover.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Thinner
Wax
Info
If you want to clean the air vents during projector operation, ensure you press
STANDBY/ON on the projector or STANDBY on the remote control and put the
projector into Standby mode. After the cooling fan has stopped, clean the vents.

Appendix

69

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector. If a problem occurs, either the temperature warning indicator or the lamp indicator will
illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.
Top V i e w
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “
” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you fi nd the temperature warning indicator blinking, be sure to perform the measures described on page
About the lamp indicator
Temperature warning indicator
Lamp indicator
Power indicator
71.
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp.” will
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.
If you tr y to turn on the projector a fourth time without replacing the lamp, the
projector will not turn on.
Indicators on the Projector
Power indicator Red on Normal (Standby)
Green on Normal (Power on) Red blinks Abnormal (See page Green blinks Normal (Cooling)
Lamp indicator Green on Normal
Green blinks The lamp is warming up.
Temp eratu re warning indicator
Red on The lamp is shut down abnormally or requires to be
Off Normal Red on/Red blinks The internal temperature is abnormally high. (See page
changed. (See page
70
71.)
71.)
71.)
Maintenance indicator
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Green on
when the
warming
Green on/
(Cooling)
Normal Abnormal
Off Red blinks
(Green
blinks
lamp is
up.)
Red on
Green blinks
(On)/
Red on
(Standby)
Red on The lamp does
Red on
(Standby)
Red blinks The power
Problem Cause Possible Solution
The internal temperature is abnormally high.
not illuminate.
Time to change the lamp.
The lamp does not illuminate.
indicator blinks in red when the projector is on.
Temperatures
• around the projector are high. Blocked air intake
Cooling fan
• breakdown Internal circuit failure
• Clogged air intake
The lamp is shut
Disconnect the power cord down abnormally.
Remaining lamp life
Carefully replace the lamp. becomes 5% or less.
Burnt-out lamp
• Lamp circuit failure
The lamp unit cover
If the power indicator blinks is open.
Use the projector in an
• area with a temperature of lower than 95°F (+35ºC). Relocate the projector to
• an area with proper ventilation. (See page
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page repair.
• from the AC outlet, and then connect it again.
• (See page Take the projector to your
• nearest Sharp Authorized Projector Dealer or Service Center (see page repair. Please exercise care when
• replacing the lamp. Securely install the cover.
• in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page advice.
72.)
8.)
84) for
84) for
84) for
Info
If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
Appendix
71

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a signifi cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page Purchase a replacement lamp of type AN-SV10LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
60.)
U.S.A ONLY

Replacing the Lamp

Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
• cool before removing the lamp unit.
Carefully change the lamp by following the instr uctions described in this section.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
72
Removing and Installing the
2
3
Lamp Unit
Warning!
Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.
Info
Do not touch the glass surface of the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. Do not loosen other screws except for the
• lamp unit cover and lamp unit.
Press STANDBY/ON on the
1
1
projector or STANDBY on the remote control to put the projector into Standby mode.
Disconnect the power cord.
2
Unplug the power cord from the AC socket. Leave the lamp until it has fully cooled
• down (about 1 hour).
Optional
Optional
accessory
accessory
STANDBY/ON
STANDBY/ON button
button
AC socket
AC socket
Lamp unit
Lamp unit AN-SV10LP
AN-SV10LP
Remove the lamp unit cover.
3
Loosen the user service screw (1) that
• secures the lamp unit cover. Remove the lamp unit cover (2).
User service screw
User service screw (for lamp unit cover)
(for lamp unit cover)
Appendix
73
5
6
2
Regarding the Lamp (Continued)
Remove the lamp unit.
4
4
Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.
Handle
Insert the new lamp unit.
5
Press the lamp unit fi rmly into the lamp unit compartment. Fasten the securing screw.
Replace the lamp unit cover.
6
Align the tab on the lamp unit cover (1) and close it (2). Be careful not to get the strap caught in the cover. Then tighten the user service screw (3) to secure the lamp unit cover.
Info
If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
Handle
Securing screws
Securing screws

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
Connect the power cord.
1
Plug the power cord into the AC socket of the projector.
Reset the lamp timer.
2
While simultaneously holding down
MENU, ENTER and press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green. “LAMP 0000H” is displayed, indicating
• that the lamp timer is reset.
R on the projector,
74
AC socketAC socket
STANDBY/ON button
STANDBY/ON button
ENTER button
ENTER button
R button
R button
MENU button
MENU button

Compatibility Chart

Computer
• Multiple signal support Horizontal Frequency: 15-110 kHz, Vertical Frequency: 45-85 Hz,
PC/MAC Mode Resolution
VGA 640 × 480
SVGA 80 0 × 600
XGA 1024 × 768
PC
MAC 13" VGA 64 0 × 480 3 4.9 67 MAC 16" SVGA 832 × 624 4 9.7 75 MAC 19" XGA 1024 × 768 60.2 75
MAC 21" SXGA 1152 × 870 68.7 75
WSXGA+ 1680 × 1050 65.3 60
1280 × 720 45.0 60 1280 × 768 47.8 60
WXGA
1280 × 800
1360 × 768 47.7 60 1366 × 768 47.8 60
WXGA+ 1440 × 900 55.9 60
1152 × 864
SXGA
1280 × 960
1280 × 1024
SXGA+ 1400 × 1050
UXGA 1600 × 1200 75.0 60
Horizontal
frequency [kHz]
26.2 50
31.5 60
34.7 70
37.9 72
37.5 75
43.3 85
31.3 50
35.2 56
37.9 60
46.6 70
48.1 72
46.9 75
53.7 85
40.3 50
48.4 60
56.5 70
60.0 75
68.7 85
49.7 60
62.8 75
55.0 60
66.2 70
67.5 75
60.0 60
75.0 75
64.0 60
80.0 75
64.0 60
65.3 60
Verti cal
frequency[Hz]
Pixel Clock: 12-165 MHz Sync signal: Compatible with TTL level
• Compatible with sync on green signal
Analog
Support
✔ ✔✔ ✔ ✔✔ ✔✔ ✔ ✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔ ✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔ ✔✔ ✔✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔✔ ✔✔ ✔✔ ✔✔ ✔ ✔ ✔ ✔ ✔
Digital
Support
Display
XG-SV100 W XG-SV20 0X
Upscale
TRUE
Intelligent
Compression
Upscale
Intelligent
Compression
Upscale
TRUE
Intelligent
Compression
Upscale
TRUE
Intelligent
Compression
Note
Optimum image quality will be achieved by matching your computer's output resolution to the
• resolution that corresponds to “TRUE” in the “Display” column shown above.
When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures shown below. – Refer to “Resolution” on the “SIG” menu and select the same resolution as the resolution in “Screen
resolution” of the computer. Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.
Appendix
75
Compatibility Chart (Continued)
3D Supported Signals
Signa l Hor izonta l Frequen cy (kHz) Ver tical Fr equen cy (Hz)
SVGA 80 0 × 600
XGA 1024 × 768
WXGA
1280 × 800
1280 × 720
37.9 60
77.1 120
48.4 60
98.6 120
49.7 60
101.6 120 *
45.0 60
92.6 120
1
*1 Reduced Blanking
Note
Your computer graphics card must be able to display 3D stereoscopic signals.
• Please check with your computer/graphic card specifi cations or call your computer manufacturer to ensure this capability.
DTV
Horizontal
Signal
Freque ncy (kHz)
I
I
I
15.7 60
15.6 50
33.8 60
480 480P 31.5 60 540P 33.8 60 576 576P 31.3 50 720P 37.5 50 720P 45.0 60
1035
Vert ical
Freque ncy (Hz)
Analog
Support
Digital
Support
✔✔
✔✔
✔✔
✔✔
Horizontal
Signal
Freque ncy (kHz)
1080I
1080 1080P 27.0 24 1080P 28.1 25 1080P 33.8 30 1080P 56.3 50 1080P 67.5 60
28.1 50
33.8 60
I
Analog
Support
✔✔
✔✔
✔✔
✔✔
Vert ical
Freque ncy (Hz)
Analog
Support
✔✔
✔✔
✔✔
✔✔
Digital
Support
Digital
Support
76
Attaching the Ceiling-mount Rotating Module
2
3
(AN-SV100T)
Press STANDBY/ON on the
1
1
projector or STANDBY on the remote control to put the projector into Standby mode. Then disconnect the power cord.
Turn over the projector and place
2
it upside down on a fl at surface. Remove the connector cover.
Place the ceiling-mount rotating
3
module on the bottom of the projector so that it is aligned with the module installation holes on the projector. (Make sure the three position-setting pins on the module are inserted into the position-setting holes on the projector.)
Using the supplied bolts, attach
4
4
the ceiling-mount rotating module to the projector. First, lightly screw all four bolts and then tighten them fi rmly.
Appendix
77

Attaching the Terminal Cover to the Module

Fix the hooks of the terminal
1
covers ( protrusions on the covers into the slots on the ceiling-mount rotating module (AN-SV100T) (
) and fi t the small
).
Fasten the terminal covers at the
2
two points with the supplied screws.
ScrewsScrews
78

Attaching the Ceiling Mount to the Ceiling

2
When installed with the AN-TK201
Attach the ceiling mount to the
1
1
ceiling.
First, lightly screw an installation bolt into the smallest hole doing the same for the holes Once the position has been decided, fi rmly tighten all four bolts. Use M8-type bolts. (Bolt type may vary
• depending on the method of installation.) Use
the washers supplied with the
ceiling mount.
Attach the height-adjustment
2
pole to the ceiling mount.
1.
Insert the height-adjustment pole into the ceiling mount. Fix the pole in place with the sleeve and
2. pole-fi xing bolt of the screen. Lock the bolt in place with the securing
3. nut
.
Screw in the two stabilizing screws
4. Tighten the securing nut
5. the pin bolt.
into the hole on the pole-fi xing
and then proceed,
, and .
, according to the height
.
fi rmly and fi t
Washer
Washer
Mounting bolt (M8-type)
Mounting bolt (M8-type)
Pin hole
Pin hole
Sleeve
Sleeve
Caution
Ask your dealer or service shop to install the
• ceiling mount. Sharp will assume no responsibility whatsoever if inadequate installation causes your projector or attached devices to fall out of place.
Appendix
79
Attaching the Ceiling Mount to the Ceiling (Continued)
When installed with the AN-TK202
Attach the ceiling mount to the
1
ceiling.
First screw a bolt into the hole (smallest hole) and tighten it enough to keep the mount in place. Then, do the same for the holes
, and . Position the four corners correctly, and then tighten all bolts fi rmly. Use M8-type bolts. (Bolt type may vary
• depending on the method of installation.) Use the washers supplied with the ceiling
• mount.
Caution
Ask your dealer or service shop to install the ceiling mount. Sharp will assume no responsibility whatsoever if inadequate installation causes your projector or attached devices to fall out of place.
80

Troubleshooting

Problem Check Page
Projector power cord is not plugged into the wall outlet.• Power to the external connected devices is off. – The selected Input mode is wrong.• The AV Mute function is working. 35 Cables are incorrectly connected to the projector. 22–26
No picture and no sound
or projector does not
start.
Sound is heard but no
picture appears
(or picture is dark).
Dark or bluish image
Color is faded or poor.
Picture is blurred;
noise appears.
Remote control battery has run out. 15 External output has not been set when connecting a notebook computer.
22 The lamp unit cover is not installed correctly. 73, 74
Cables are incorrectly connected to the projector.• “Bright” is set to minimum position. 48
Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer's operation manual for how to switch its signal output settings. Is “On” selected in “DLP
Check that “Wall Color” is confi gured correctly.
Image adjustments are incorrectly set.
Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “BrilliantColor
(S-Video, Video Input only)
Video input system is incorrectly set.
(COMPUTER/COMPONENT 1, 2 Input only)
Input signal type (RGB/Component) is incorrectly set.
Adjust the focus.• The projection distance exceeds the focus range. 19, 20 There is fog on the lens. If the projector is carried from a cold room into a
– warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
Perform “SIG” Adjustments (“Clock” and “Phase” Adjustment)
• Noise may appear depending on the computer.
Cables are incorrectly connected to the projector.
Volume is set to minimum.
When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.
TM
” value.
®
LinkTM”?
26
34
22–26
67
54
48
53
52
30
52
22–26
35
Picture appears but no
sound is heard.
Data image is not
centered.
An unusual sound is
occasionally heard from
the cabinet.
“Speaker” is set to “Off”. 51
Make the necessary adjustments of each item in the “SIG” menu.
Depending on the computer you are using, the output resolution signal may be different from the one you have set. For details, refer to the operation manual of the computer.
If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
52
Appendix
81
Troubleshooting (Continued)
Problem C heck Page
Maintenance indicator on
the projector illuminates
or blinks in red.
Picture is green on
COMPUTER (YPbPr)
Picture is pink
(no green) on
COMPUTER (RGB)
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
fl i c k e r s .
The lamp needs much
time to turn on. Picture is dark.
The remote control
cannot be used.
The Rotate indicator does
not light up.
The lens shift function
does not work.
See “Maintenance Indicators”.
Change the input signal type setting.
Image adjustments are incorrectly set.
When temperature inside the projector increases, the cooling fan runs
faster. The lamp indicator is illuminating in red.
Replace the lamp.
Cables are incorrectly connected to the projector or the connected equipment works improperly. If this happens frequently, replace the lamp.
The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
Operate the remote control while pointing it at the projector's remote control sensor.
The remote control may be too far away from the projector.
When using the ceiling-mount rotating module (AN-SV100T) and rotating the projector, the signal transmission to the sensor may not work depending on the rotation angle of the projector.
If direct sunlight or a strong fl uorescent lamp is shining on the projector's remote control sensor, place the projector where it will not be affected by strong light.
The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
Is “Off” selected in “Rotate Indicator” ?
Check the connection of the ceiling-mount rotating module (AN-SV100T) and projector.
The lens cover is not attached correctly.
70
52
48
8, 9 69, 70, 71
70, 73, 74
22–26
73 73
15
15
59
12
82
Problem Check Page
3D images fl icker when
watching in a room.
Ghosting (a double image)
occurs without the image
appearing in 3D.
Images may appear to fl icker when fl uorescent light or ambient light
• enters your vision.
Turn off the lights.
Block any ambient light.
Check that you are using 3D LCD shutter glasses that support the DLP® Link™ system.
Be sure to use 3D LCD shutter glasses that support the DLP system.
Check that the shutters on the 3D LCD shutter glasses are working
• properly.
Turn the 3D LCD shutter glasses off and then on again.
Check the batteries of the 3D LCD shutter glasses.
Check that the 3D LCD shutter glasses are set to 3D viewing mode.
Some 3D LCD shutter glasses are equipped with a special viewing mode (such as “dual view mode”) in addition to the normal 3D viewing mode. See the operation manual of your 3D LCD shutter glasses.
Check the settings of the projector.
Turn the DLP
Use “DLP
Check whether a signal that is not supported is being input.
Confi gure your 3D application at the correct resolution and refresh
rate. Make sure you are running your 3D application in resolutions that suppor t 3D. To support 3D, your 3D application must be confi gured to run at the correct settings for this projector. For details on the supported signals, see “3D Supported Signals” of the Compatibility Chart.
If the projector is connected to a computer for 3D image playback,
• check that a stereoscopically-enabled application is being used.
Use the applicable software.
Set the applicable software to the fi eld sequential format.
Check that there are no obstructions between the screen and the 3D
• LCD shutter glasses.
Remove any obstructions.
Any obstructions may cause the glasses not to function properly causing the lenses to fl icker or turn off. Do not place your hand or other objects in front of the 3D control signal sensor on the glasses.
Check whether there is a source of high intensity lighting nearby.
Block the light or turn it off.
High intensity lighting can interfere with communication between the 3D LCD shutter glasses and the screen resulting in some fl icker.
Check whether two or more projectors are projecting 3D images at the
• same time.
Use only one projector at a time.
®
Link™ function “On”.
®
Link™ Invert” to change the setting.
®
Link™
76
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
Appendix
83

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, fi rst refer to the “Troubleshooting” section on pages manual does not answer your question, please contact the SHARP Service departments listed below.
81 to 83. If this operation
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
http://www.sharpusa.com
Canada Sharp Electronics of Canada Ltd.
http://www.sharp.ca
Mexico Sharp Electronics Corporation
(525) 716-9000 http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin
(305) 264-2277 www.servicio@sharpsec.com http://www.sharpla.com
Germany Sharp Electronics (Europe) GMBH
01805-234675 http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
08705 274277
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1 http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se
Austria Sharp Electronics (Europe) GMBH
0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at
lcdsupport@sharpsec.com
(905) 568-7140
Mexico Branch
American Group
http://www.sharp.co.uk/customersupport
Branch Offi ce Austria
Benelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu
Australia Sharp Corporation of Australia Pty.
1300-135-022 http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111 http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
(91) 11- 6431313 service@sharp-oa.com
Nederland
Ltd.
Korea
(82) 2-3660-2002
Limited
84
Specifi cations
Model XG-SV100W XG-SV200X Display devices 0.65" DLP® Chip ×1 0.7" DLP® Chip ×1 Resolution WXGA (1280 × 800) XGA (1024 × 768) Lens F number F 2.5 – 3.7
Input terminals HDMI ×1
Output terminals
Control and communication terminals
Speaker 10 W (Mono) Projection lamp 400 W Rated voltage AC 100 – 240 V Rated frequency 50/60 Hz Input current 5.2 A Power consumption Eco+Quiet
Power consumption (STANDBY Mode)
Operation temperature 41ºF to 95ºF (+5ºC to +35ºC) Cabinet Plastic Dimensions (main body only) [W × H × D] 15
Weight (approx.) 16.5 lbs. (7.5 kg)
Zoom Power, ×2.0 (f = 21.2 – 42.0 mm) Focus Power
Computer/Component (mini D-sub 15 pin)
S-Video (mini DIN 4 pin) ×1 Video (RCA) ×1 Audio (ø3.5 mm stereo minijack) ×1 Audio (RCA) ×1 (L/R) Computer/Component
(mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) ×1 (variable audio output) LAN (RJ-45) ×1 USB (Type B) ×1 RS-232C (mini DIN 9 pin) ×1
Off Eco+Quiet OnAC 100 V 396 W
Standard AC 100 V 12.2 W
Eco AC 100 V 0.35 W
AC 100 V 516 W AC 240 V 495 W
AC 240 V 383 W
AC 240 V 12.8 W
AC 240 V 0.70 W
×2
×1 (Shared with COMPUTER/COMPONENT 2; switchable)
61
/64" × 4 33/64" × 16"
(405 × 114.5 × 406.5 mm)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specifi cation changes for product improvement without prior notice. The performance specifi cation fi gures indicated are nominal values of production units. There may be some deviations from these values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,024,000 (XG-SV100W) or 786,432 (XG-SV200X) pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Appendix
85

Dimensions

Units: inches (mm)
1561/64 (405)
16 (406.5)
/16 (338)
5
13
/64
25
2
/64
59
2
/2 (89)
1
3
/64 (160.5)
21
6
/2
1
1
(60.5)
(74)
(38)
763/64 (202.5)
29/64
(54)
M4 M4
M4 M4
15/8
(41.25)
33/4 (95)
M4 M4
M4
731/64 (190)
1163/64 (304)
ø68
M4
261/64
(75)
/64
25
/64 (114.5)
33
4
(10)
/4 (95)
3
3
/16 (134.5)
5
5
/64 (190)4
31
7
/32 (110)
11
86

Index

16:9············································································· 36-39 3D MODE button ······························································ 67
AC socket ·········································································26 Adjustment buttons ·························································· 46 Adjustment foot ································································29 All Reset ···········································································60 AREA ZOOM ······························································37, 39 Aspect ratio ································································36, 38 Audio Input ·······································································51 Audio Out ·········································································51 AUDIO 1, 2 terminals ························································24 AUDIO OUT terminal ························································24 Auto Power Off ·································································56 Auto Restart ·····································································56 Auto Sync (Auto Sync adjustment) ····························41, 52 AUTO SYNC button··························································41 AV MUTE button ······························································· 35
Background ······································································55 Bass··················································································51 Batteries ···········································································15 Blue ··················································································55 BORDER ·····································································36, 37 BREAK TIMER button ······················································40 Bright ················································································48 BrilliantColor
Clock ················································································52 Closed Caption ································································· 55 CLR Temp (Color Temperature) ········································49 C.M.S. ··············································································49 Color ·················································································48 COMPUTER2 Select ························································56 COMPUTER/ Contrast ············································································48
DHCP Client ·····································································62 DLP DLP DNR ··················································································50 Dynamic Range ································································53
Eco+Quiet···································································40, 50 ECO+QUIET button ··························································40 Effect ················································································50 ENTER button ··································································· 46 Exhaust vent ··························································12,13, 69
Fan Mode ·········································································57 FREEZE button ·································································41 FOCUS buttons ································································ 30 FULL ···········································································36, 38
Geometric adjustment ······················································32 H-Pos ···············································································52
H&V KEYSTONE ·······························································33 H&V SHIFT button ····························································29 HDMI terminal·····························································22, 23 Hue ···················································································50
INPUT modes ···································································34 Intake vent ··································································13, 69 IP Address ········································································ 63
Kensington Security Standard connector ························13 Keycode ··········································································57 Keylock ············································································58 KEYSTONE button ··························································31 Keystone Correction ························································· 31
Lamp ················································································72 Lamp indicator ·································································70 Lamp Timer (Life) ······························································60 Lamp unit ·········································································73 Language (on-screen display language) ··························55 LAN terminal ·····································································26 LENS button ····································································· 12 L-CLICK/EFFECT button ············································42, 40
MAC Address ···································································63 MAGNIFY buttons ····························································41
TM
··································································48
COMPONENT1, 2 input terminals
®
LinkTM ······································································67
®
LinkTM Invert ····························································67
·········22, 23
MEMORY (1-8) buttons ····················································59 Memory Menu ··································································59 MEMORY MENU button ··················································· 59 MENU button ···································································· 46 MONITOR OUT terminal ···················································24 MOUSE/Adjustment buttons ······································42, 46
NATIVE ········································································36, 38 Network ············································································61 NORMAL ···································································· 36-39
ON button ·········································································27 Optional accessories ························································11 OSD Display ····································································54 Overscan ··········································································54
PAGE DOWN button ·························································42 PAGE UP button ······························································· 42 Password ·········································································· 61 PDF···················································································10 Phase················································································52 Picture Adjustment ··························································48 Picture Mode ······························································ 41, 48 PICTURE MODE button ···················································41 POINTER button ·······························································40 Power cord ······································································· 26 Power indicator ································································70 PRJ ···················································································56 PRJ Mode ···································································21, 55
R-CLICK/RETURN button ··········································42, 46 Red ···················································································48 Remote control ·································································14 Remote control sensor ····················································· 15 Replacing the lamp·····················································72, 73 Reset Network Setting ·····················································62 Resize ·········································································36, 54 RESIZE button ··································································36 Resolution·········································································52 Restart Network ·······························································62 RGB cable ········································································22 ROTATE button ·································································14 Rotate Indicator ································································59 RS-232C terminal ·····························································25
Saturation ·········································································50 SCR ··················································································54 Screen Size and Projection Distance ·························19, 20 Select Color ······································································50 Sharp ················································································48 SIG····················································································52 Signal Info ········································································· 53 Signal Type ·······································································52 Speaker ············································································51 SPOT button ·····································································40 STANDBY button ······························································27 STANDBY Mode ·······························································56 STANDBY/ON button ·······················································27 Supplied accessories ·······················································11 S-VIDEO terminal ·····························································23 System Lock ·····································································57
TCP/IP ··············································································62 Temperature warning indicator ·········································70 Tint····················································································48 Treble ················································································51
USB terminal ····································································42 Value ·················································································50
Video Setup ······································································53 Video System ···································································53 VIDEO terminal ·································································23 VOL (Volume) buttons ·······················································35 V-Pos ················································································52 V-STRETCH ································································37, 39
Wall Color ········································································· 54 ZOOM buttons ·································································30
Appendix
87
Loading...