1
1. Open the cover (➊) and remove
the tape (➋).
2
2. Close the print compartment cover. (Do not install the
print cartridge yet.).
2
Quick Setup Guide
Inkjet Fax UX-B800
Connect the handset
3
Attach the trays
Attach the received
document tray
1
Attach the document
exit tray and flip out
the extension
Pull the received
document tray
extension all the
way out
Attach the
paper tray
4
Load paper
Fan the paper, and tap the
edges against a flat surface to
even the stack.
The stack should not be
higher than this line
Pull the paper
plate forward
and insert the
paper print
side up.
5
1. Connect the phone line cord to the
TEL. LINE socket and a wall
telephone socket.
TEL.
SET
TEL.
LINE
2. Plug the power cord into a 230 V
earthed (3-prong) AC outlet.
(TCADH3911XHZZ)
6
Install the Print Cartridge
1. Open the operation panel.
5. Close the cover, pressing firmly on
both front corners.
Display:
CHANGE CARTRIDGE
1=NEW, 2=OLD
2. Remove only the tape from the new cartridge.
IMPORTANT: Make sure all tape is removed.
Caution! Do not touch
the gold contact area.
6. a. Press to select NEW.
b. Press .
The machine will print an alignment page.
3. Make sure the cartridge holder is in the
position shown. Place your fingers on top
of the holder and open the holder
release.
7. In the alignment page,
locate the line that is
closest to a completely
straight line. Enter the
number of that line.
Example:
(To clear a mistake,
press .)
In this example, “15” is
closest to a straight line
4. Insert the new print cartridge (➊).
Close the holder (➋), making
sure it clicks into place.
2
1
8. Press .
Note: To enter your
name and fax number
and set the date and
time so that they appear
at the top of each fax
page you send, see
pages 13 - 14 of the
manual.
Setup for Fax/Scan to E-mail
7
WAN port
Internet
Cable/DSL
modem
To use Fax/Scan to E-mail you must:
1. Have an Internet connection
2. Have a router, hub, or switch through which the
machine can be connected to the Internet.
LAN cable
LAN ports
(Hub/Switch)
Router
LAN cable
LAN cable
LAN cable
Connect one end of an
Ethernet cable (not included)*
to the LAN port on the
machine, and the other end to
a LAN port on your router,
switch, or hub.
*Please purchase a straightthrough (regular) Ethernet
cable that supports 10Base-T.
The machine requires an IP address to communicate. Most
networks assign an IP address automatically when a device
is connected.
If your network requires that a permanent IP address be
assigned to the machine, see page 25 of the manual.
To use Fax/Scan-to-E-mail, you must configure the “Sender
Address”, and “SMTP Server” settings (see pages 17 -19 of
the manual). You must also configure the “SMTP
Authentication” setting if required by your Internet service
provider. This can be done in the machine’s Web page.
First press the keys on the machine as follows to check the
IP address of the machine (page 16 of the manual).
1. Press , then until [NETWORK SETTING]
FUNCTION
appears.
2. Press , then to show [NETWORK
INFORMATION].
3. Press . The address will appear on the bottom line of
the display.
Open the browser on a computer connected to the same
network as the machine, and type in the machine’s IP
address in the Address bar of the browser. The machine’s
Web page will open. Select “E-mail Setup” in the menu
frame and configure the settings. For detailed information
on each setting, click “Help” in the menu frame.
If you don’t know the information that must be entered in
each setting, ask your Internet service provider.
Example: