Sharp PC817X, PC817X0, PC817X1, PC817X2, PC817X3 Datasheet
...
I
SPEC. No.
ED-94054D
SW 1 ISSUE Junel4, 1996
ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION
SPECIFICATION
DEVICE SPECIFICATION FOR Business
dealing name
PHOTOCOUPLER
MODEL No.
PC817
1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This product is designed for use in the following application areas :
[
* OA equipment * Audio visual equipment * Home appliances
* Telecommunication equipment (Terminal)
* Measuring equipment
* Tooling machines
* Computers
1
If the use of the product in the above application areas is for equipment listed in paragraphs
(21 or (31. please be sure to observe the precautions given in those respective paragraphs.
(21 Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as :
[
* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers
* Rescue and security equipment
* Other safety equipment
1
(31 Please do not use this product for equipment which require extremely high reliability
and safety in function and precision. such as :
[
* Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment * Medical equipment
,I
(41 Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
PRESENTED “I
BY
L/
DATE
T. Matsumura,
Department General Manager of
Engineering
Dept.,11
BY
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
SHARP CORPOMITION
ED-94054D 1 June 14, 1996
MODEL No.
PAGE
PC8 17x
l/8
1. Application
This speciiication applies to the outline and characteristics of photocoupler
Model-No. PC8 17series.
Refer to the attached drawing No. CY696
lK02.
2. Outline
3. Ratings and characteristics
Refer to the attached sheet, page 3 to 6.
4. Reliability
Refer to the attached sheet, page 7.
5. Incoming inspection
Refer to the attached sheet, page 8.
6. Supplement
6.1 Isolation voltage shall be measured in the following method.
(1) Short between anode to cathode on the primary side and between collector
to emitter on the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shall be used.
(31 The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
SHflRP CORPORATION
ED-94054D 1 June 14. 1996
I
MODEL No.
PC817X
PAG E
2/B
6.2 Business dealing name
(,, 0” mark indicates business dealing name of ordered product)
6.3 This Model is approved by UL.
Approved Model No. : PC8 17‘
UL file No. : E64380
6.4 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting diode.
7. Notes
Refer to the attached sheet- 1 - 1, 2.
Test
conditions
IF=5mA
Ta=25C
SHARP CORPORATION
ED-94054D 1 June 14, 1996
MODEL
No.
PAGE
PC8 17x
3/8
3. Ratings and characteristics
3.1 Absolute maximum ratings
Ta=25%
Collector current
* 1 Collector power dissipation PC 150 mW
* 1 Total power dissipation Ptot 200
mW
*3 Isolation voltage
Vii0
5 kVrms
Operating temperature Topr -30 to +lOO ‘C
Storage temperature
Tstg
-55 to +125 “C
*4 Soldering temperature Tsol 260 “C
*l The derating factors of absolute maximum ratings due to ambient temperature
are shown in Fig. 1 to 4.
*2 Pulse widths100 /IS, Duty ratio : 0.001 (Refer to Fig. 5)
*3 AC for 1 min. 40 to 6O%RH
*4 For 10s
Loading...