SHARP LC-32LE210E, LC-32LE210RU, LC-32LE210RUB, LC-32LE210EB, LC-32LE220RU Service Manual

...
LC-32LE210 LC-32LE220
SERVICE MANUAL
SE00LC32LE210
Issued: 16th September 2010
LED LCD COLOUR TELEVISION
DVB-T / DVB-C (HDTV), PAL
B/G, I
/ SECAM
B/G, D/K, L/L’
SYSTEM COLOUR TELEVISION
MODELS
LC-32LE210E/RU LC-32LE210EB/RUB LC-32LE220E/RU LC-32LE220EB/RUB LC-32LB220E/RU LC-32LB220EB/RUB LC-32LS220E/RU LC-32LS220EB/RUB
In the interests of user safety (required by safety regulations in some countries) the set should be re­stored to its original condition and only parts identical to those speci ed should be used.
CONTENTS
ELECTRICAL SPECIFICATIONS .............................................................................. 2
IMPORTANT SERVICE SAFETY PRECAUTIONS...................................................... 3
OPERATION MANUAL ............................................................................................... 6
DIMENSIONS ......................................................................................................... 10
REMOVING OF MAJOR PARTS ................................................................................................ 11
SERVICE ADJUSTMENTS ..................................................................................... 16
SOFTWARE UPDATING .................................................................................... 28
MAJOR ICs INFORMATION ..................................................................................... 29
SOURCE OF DOCUMENTATION ..................................................................................... 38
CHASSIS LAYOUT .................................................................................................. 39
WIRING DIAGRAMS ......................................................................................... 43
BLOCK DIAGRAMS ......................................................................................... 45
SCHEMATIC DIAGRAMS ......................................................................................... 51
PRINTED WIRING BOARDS ..................................................................................... 69
REPLACEMENT PARTS LIST .................................................................................. 76
CABINET AND MECHANICAL PARTS .......................................................................... 89
PACKING OF THE SET ........................................................................................... 91
SHARP CORPORATION
1
This document has been published to be used for after sales service only. The contents are subject to chage without notice.
LC-32LE210 LC-32LE220
Speci cations
ELECTRICAL SPECIFICATIONS
Item
LCD Panel
Resolution 6.220.800 dots (1.920 x 1.080 pixels)
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV Standard Analogue CCIR (B/G, I, D/K, L/L’)
TV
Func­tions
Viewing angles H: 176°, V: 176°
Audio Amplifier
Speaker (25 mm x 100 mm) x 2 (30 mm x 100 mm) x 2
Terminals
OSD language
Power Requirement AC 220–240 V, 50 Hz
Power Consumption (IEC62087 Method) 30W (0.25 W Standby) 85W (0.25 W Standby)
Weight 4,9 Kg (Without stand), 6 Kg (With stand) 8,5 Kg (Without stand), 9,8 Kg (With stand)
Operating Temperature 0 °C to +40 °C
Receiving Channel
TV-Tuning System Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
STEREO / BILINGUAL NICAM/A2
TV Antenna UHF/VHF 75 Din type (Analogue & Digital)
SERVICE Ø 3.5 mm jack
SCART SCART (AV input, RGB input, TV output, Y/C input)
PC INPUT VGA (D-Sub 15pin), Ø 3.5mm jack
COMPONENTS COMPONENT IN: Y/PB(CB)/PR(CR), RCA (AUDIO R/L)
HDMI1 HDMI, Ø 3.5mm jack
HDMI2 HDMI, Ø 3.5mm jack
HDMI3 HDMI, Ø 3.5mm jack
AV RCA connector (AV input)
MEDIA PLAYER/ TIME-SHIFT/ USB REC
DIGITAL AUDIO OUTPUT RCA S/PDIF digital audio output.
C. I. (Common Interface) EN50221, R206001, CI+ speci
Headphones Ø 3.5 mm jack (Audio output)
Digital DVB-T (2K/8K OFDM)(H.264), DVB-C (Only Lx220)
VHF/UHF E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR A ch–E69 ch)
CATV Hyper-band, S1–S41 ch
24” LCD COLOUR TV, Model:
LCD COLOUR TV, Model:
LC-24LE210E,
LC-32LE210E, LC-32LB220E, LC-32LE220E, LC-32LS220E.
LC-24LE220E
32” TFT LCD LED TV
24" BLACK TFT LCD LED TV 32” BLACK TFT LCD LED TV
10 W x 2
(30 mm x 100 mm) x 2
USB 2.0 HOST (A type)
cation (Only Lx220)
#ZECHç$ANISHç$UTCHç%NGLISHç%STONIANç&INNISHç&RENCHç'ERMANç'REEKç(UNGARIANç)TALIANç ,ATVIANç,ITHUANIANç.ORWEGIANç0OLISHç0ORTUGUESEç2USSIANç3LOVAKç3LOVENEç3PANISHç 3WEDISHç4URKISHç5KRAINIANç"YELORUSSIANç2OMANIAN
85 W (0.25 W (Standby)
8,5 Kg (Without stand), 9,8 Kg (With stand)
32” LCD COLOUR TV, Model: LC-32LE210E, LC-32LE220E,
LC-32LB220E, LC-32LS220E
Environmental Specifications
32”
*1 On-Mode (W) (HOME MODE)
*2 Energy-Save-Mode (W) ECO
*3 Standby-Mode (W)
*4 Off Mode (W)
*5 Annual Energy Consumption (kWh)
*6 Annual Energy Consumption Energy-Save-Mode (kWh)
ECO
63 W
48 W
0.25 W
0.18 W
92 kWh
71 kWh
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, offi ce), the picture may leave trails or appear slightly delayed. This is not a malfunc­tion, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. Storage temperature: –20°C to +60°C
.
*1 Measured according to IEC 62087 Ed. 2. *2 For further information about the Energy Save function,
please see related pages in this operation manual.
*3 Measured according to IEC 62301 Ed. 1. *4 Measured according to IEC 62301 Ed. 1. *5 Annual energy consumption is calculated on the basis
of the On-Mode (HOME MODE) power consumption, watching TV 4 hours a day, 365 days a year.
*6 Annual energy consumption is calculated on the basis of
the Energy-Save-Mode power consumption, watching TV 4 hours a day, 365 days a year.
2
• As a part of our policy of continuous im­provement, SHARP reserves the right to make design and specifi cation changes for product improvement without prior notice. The performance specifi cation fi g­ures indicated are nominal values of pro­duction units. There may be some devia­tions from these values in individual unit
s.
LC-32LE210 LC-32LE220
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by quali ed service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modi cation of any circuit should be attempted.
2. Disconnect AC power before servicing.
CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE REPLACE ONLY WITH SAME TYPE F101 (T3.15AH / 250V)
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)
Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner.
Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use an isolation transformer for this test).
•Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15F capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
•A true RMS reading multimeter should be used for this test, especially where the equipment uses a switch mode power supply which may result in very non-sinusoidal leakage current.
•Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.
All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must be used only for the purpose of completing these checks.) Any reading of 1.05V peak (this corresponds to 0.7 mA. peak AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the monitor to the owner.
DVM
AC SCALE
1.5k ohm 10W
0.15 F
TEST PROBE
TO EXPOSED METAL PARTS
CONNECT TO KNOWN EARTH GROUND
SAFETY NOTICE
Many electrical and mechanical parts in LCD television have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identi ed in this manual; electrical components having such features are identi ed by “ “.
!
For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock,  re or other hazards.
3
LC-32LE210 LC-32LE220
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1 Employing lead-free solder
“ALL PWB” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example:
L Fa
Indicates lead-free solder of tin, silver and copper.
L Fn
Sn-Ag-Ni
Indicates lead-free solder of tin, silver and nickel.
2 Using lead-free wire solder
When  xing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you con rm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use,  le it with steel wool or  ne sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing.
4
END OF LIFE DISPOSAL
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. Following the implementation by member states, private households within the EU states may return their used
Attention: Your product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one. *) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.
2. In other Countries outside the EU
LC-32LE210 LC-32LE220
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
5
LC-32LE210 LC-32LE220
B (Standby/On) indicator
OPERATION MANUAL
11 HDMI 3 (HDMI/ DVI)
12 AUDIO input for DVI and PC.
13 COMMON INTERFACE slot
14 AC INPUT terminal
TV (Front view)
Switch the sound on and off.
18 2 Audio mode
17 e Mute
Remote control sensor
TV/DTV/CADTV: Select the program
or move up or down the channel list
pages.
Input source: Switch to TV or DTV
or CADTV input mode.
Teletext: Move to the next/previous
page.
i (+) Increase the volume.
i (-) Decrease the volume.
Select the sound multiplex mode.
(See below.)
19 i (+/-) Volume
20 P (r/s)
21 b Input source
TV (Top and rear view)
Select an input source.
(See page 10.)
22 RADIO
DTV/CADTV: Switch between
RADIO and digital mode.
•Due to the large variation in
transmitted volume levels in RADIO
mode, some stations will produce
TELETEXT: Select a page. (See
page 12.)
Display the MENU screen.
(See page 18.)
distortion if the volume level is set
too high.
23 PC
Select PC input source (Analogue
25 REC
connection, see page 16.)
24 MENU
DTV/CADTV: The coloured buttons
Starts the USB REC recording.
26 Colour (Red/Green/Yellow/Blue)
a (Power button)
(MENU button)
b (INPUT SOURCE button)
Switch the Teletext image to Top,
Bottom or Full.
(See page 12.)
ATV: Subtitles on / off.
are used to select correspondingly
DTV/CADTV: Display the subtitle
to the coloured items in the menu
screen.
27 [ Subtitle for Teletext
29 v Top/Bottom/Full
selection screen. (See page 10
and 12.)
28 k Reveal hidden Teletext
6 Antenna input terminal
7 DIGITAL AUDIO OUTPUT terminal
P(r/s) (Programme (channel) buttons)
i(k/l) (Volume buttons)
1 USB terminal
2 COMPONENTS / AV terminals
CADTV only Lx220 series.
*
30 1 Subpage
(See page 12.)
8 SERVICE connector (jack 3.5mm)
9 HDMI 1 (HDMI/DVI)
10 HDMI 2 (HDMI/DVI)
3 HEADPHONES jack
4 SCART (AV/RGB, Y/C Input) terminal
5 PC Input
CH A, CH B, CH AB
Remote control unit
(See pages 11 and 22.)
3 MEDIA PLAYER
Display the MEDIA PLAYER screen.
4 0–9
1 B Standby/On
Enter standby mode or turn on the
power.
2 p Channel information / EPG
Set the channel in TV mode.
.
When one of the 5 Nordic countries
(Sweden, Norway, Finland, Denmark or
Iceland) is selected in the country setting
of Auto Installation, DTV channels are 4
digits. When another country is selected,
Set the page in Teletext mode.
DTV channels are 3 digits
5 A Flashback
Press to return to the previous
mode.
TimeShift / Play-Pause
/
Activate or deactivate the TimeShift.
Start / stop the reproduction.
Change between different picture
formats (see page 23.)
Change between ATVļDTV or
TV mode: Select a desired item on
selected channel or external input
mode.
6 DTV
7 f Picture format
8
ATV ļ CADTV*
the setting screen.
9 a/b/c/d (Cursor)
6
Teletext
ATV: Select the TELETEXT mode
(See page 12.)
DTV/CADTV: Select DTV/CADTV
(MHEG-5) data broadcasting or
TELETEXT.
13 FAV
12 m
L
V
/
/
S
USB REC and TimeShift mode:
T
Rewind and forward the recording in
Rewind and fast forward.
Shows the favourite list.
units of 5 minutes.
OK
Execute a command within the
menu screen.
ATV/DTV or ATV/CADTV mode:
Freeze a picture (TV) or the Teletext
on the screen (See page 12)
14 3 Freeze / Hold
15 SLEEP
Set the sleep timer on (in units of
10 min. up to max. 4 hr) and off.
16 REC LIST
Shows list of recorded programs.
(See page 28.)
(Electronic Programme Guide) screen.
Display the channel list.
(See page 22.)
10 END
(See page 11.)
Exit the menu screen.
11 EPG
DTV/CADTV: To display EPG
A2 TV broadcasts selection
Signal Selectable items
Stereo STEREO, MONO
Bilingual
:
Using 2 on the remote control unit
DTV/CADTV mode
Press 2 to open the multi audio screen. (See page 10.)
NICAM TV broadcasts selection
Analogue TV mode:
Each time you press 2, the mode switches as illustrated in the following tables:
CH AB, MONO
NICAM CH A, NICAM CH B, NICAM
Signal Selectable items
Stereo NICAM STEREO, MONO
Bilingual
Monoaural MONO
Monoaural NICAM MONO, MONO
Operation Manual (Continued)
LC-32LE210 LC-32LE220
1 2 3
Initial installation overview
Quick guide
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary
depending on your TV installation and connection.
Watch TV
Congratulations!
n
installation
run the auto
Power on and
Turn on the power using a on
n
Preparation
Connect an antenna cable to
n
Connect
Now you can watch TV. oIf necessary, adjust the
antenna to attain maximum
signal reception (Page 9).
the TV (Page 10).
the antenna terminal (Page 8). oIf necessary, insert a CA card
Connect external
devices such as a
DVD player/recorder
n
external devices
Run the initial auto installation
(Page 9).
o
as instructed (Pages
14 and 15).
9Language and country
setting
into the CI slot to watch
scrambled broadcasts
(Page 8.)
Connect external
audio devices such as
speakers/amplifier as
instructed (Pages 14
o
and 15).
Connect the AC cord to the TV
(Page 8).
p
9TV Location setting
Store
Home
channels
Start searching
Product shape varies in some countries.
Inserting the batteries
Preparation
Before using the TV for the first time, insert two supplied “AA” size zinc-carbon batteries. When the batteries become
2 Insert two supplied “AA” size batteries.
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
1 Hold in the tab on the battery cover and pull the cover towards the direction of the arrow.
• Place batteries with their terminals corresponding to
the (+) and (-) indications in the battery compartment.
chemical leakage in old batteries.
3 Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
any chemical leakage, wipe thoroughly with a cloth.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you fi nd
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
businesses.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
7
unit and sensor may prevent proper operation.
Remote control sensor
°°
and do not place in an area with high humidity.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In addition, do not expose the remote control unit to liquids,
may cause deformation of the unit.
the TV is under direct sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote control unit closer to the
• Do not install or place the remote control unit under direct sunlight. The heat
remote control sensor.
• The remote control unit may not work properly if the remote control sensor of
LC-32LE210
Ɣ
LC-32LE220
Operation Manual (Continued)
DVI/VGA Conversion cable
mini jack cable
ø 3,5 mm stereo
PC
HDMI 1, 2 or 3
Selecting the picture size
audio cable.
NOTE
• When using the PC-IN terminal is necessary to connect a
AUDIO IN
HDMI (DVI)
You can select the picture size.
1 Press MENU on the remote control.
Example
2 Press ź key to select “Aspect ratio”.
3 Press Ź key to select the desired item.
.
Normal Full
Item
Keeps the original aspect ratio in a full
screen display
An image fully fi lls the screen
Displays an image with the same
number of pixels on the screen
Normal 4:3
Full
Dot by Dot
NOTE
• You can also select an item by pressing f on the remote
control unit.
signals through the “PC IN” terminal.
• Connect the PC before making adjustments.
• Selectable picture size may vary with input signal type.
• The “Aspect ratio” adjustment is only available for analogue
HDMI (DVI) Connection
PC connection
Connecting a PC
PC
HDMI-certified cable
DVI/HDMI Cable
PC
ø 3,5 mm stereo mini jack cable
After connection
cable, the audio does not run, connect a mini stereo
connector of ø 3.5mm between TV and PC as
indicated in the previous drawing
Ɣ
Ɣ If after connecting a PC to the TV through a HDMI
Ɣ When a PC is connected to the TV with a DVI
VGA cable
Analogue Connection
cable, it will be necessary to connect a mini stereo
connector of ø 3.5mm of the TV to PC as indicated
in the previous drawing.
PC
mini jack cable
ø 3,5 mm stereo
E Before connecting ...
Connecting external devices
get the best possible audiovisual quality to maximise the potential of the TV and the connected device.
• Be sure to turn off the TV and any devices before making any connections.
• Firmly connect a cable to a terminal or terminals.
• Carefully read the operation manual of each external device for possible connection types. This also helps you
Audio cable
Introduction to connections
The TV is equipped with the terminals as shown below. Find the cable corresponding the TV’s terminal and
connect the device.
NOTE
Audio device (Page 15)
• The cables illustrated in pages 13, 14 and 15 are commercially available items.
or
Audio cable
SCART cable
(Pages 14 and 15)
Video recording device
Components cable
Audio cable
AV cable
Game console or
camcorder (Page 14)
HDMI-certified cable
HDMI-certified cable
HDMI device (Page 14)
DVI/HDMI Cable
ø 3.5 mm stereo mini jack cable
8
Operation Manual (Continued)
If the indicator on the TV lights up red, press B.
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging
it in after one or two minutes.
• Are batteries inserted with polarity (e, f) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminating to the remote control sensor?
• Check if you pressed B on the remote control unit.
• Is the AC cord disconnected?
• Check if you pressed a on the TV.
• Are screen mode adjustments (Aspect ratio) such as picture size made correctly? (Page 23.)
• Adjust the picture tone.
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the “PICTURE” setting (Page 19).
Remove any objects blocking the vent or clean.
• Is the “Sleep Timer” set? Select “Off” from the “TIME” menu (Page 20).
• Is “No Signal Off” or “No operation Off” activated?
• Is the input signal type selected correctly after connection? (Page 10)
• Is the correct input source selected? (Page 10)
• Is the picture adjustment correct? (Pages 19)
• Is the antenna connected properly? (Page 8)
according to changes in temperature. This does not affect the TV’s performance.
• Make sure that headphones are not connected.
• Check if you pressed e on the remote control unit.
• This is not a malfunction. This happens when the cabinet slightly expands and contracts
LC-32LE210 LC-32LE220
Problem Possible Solution
Troubleshooting
Appendix
• No power.
• The TV cannot be operated. • External influences such as lightning, static electricity, etc., may cause improper operation. In this
• Remote control unit does not operate.
colour, or colour misalignment.
• Picture is cut off. • Is the image position correct?
• Strange colour, light colour, or dark
• Power is suddenly turned off. • The TV’s internal temperature has increased.
• No picture. • Are connections to external equipment correct? (Pages 13, 14 and 15)
MEDIA PLAYER function
After selecting Media Player, the TV loads USB device
files, and shows the following screen:
sound.
• The TV sometimes makes a cracking
• No sound. • Is the volume too low?
Cautions regarding use in high and low temperature environments
• When the TV is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the TV will recover when the temperature returns to normal.
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: -20 °C to e60 °C.
• Do not leave the TV in a hot or cold location. Also, do not leave the TV in a location exposed to direct sunlight or near a
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by
SHARP or by third parties.
Software developed by SHARP and/or third part
The copyrights for the software components and various relevant documents included with this product that were developed
or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant
laws. This product also makes use of freely distributed software and software components whose copyrights are held by third
parties.
fix brackets may result in an unstable installation and may cause serious injuries.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper fixing or
Fixing the TV on a wall
fixing that results in accident or injury.
This TV should be fixed on a wall only with the wall fix bracket available from SHARP (Page 5). The use of other wall
Fixing the LCD colour TV requires special skills and should only be performed by qualified service personnel.
PHOTO mode
viewing.
Press OK to select the option you want to reproduce.
different modes: PHOTO, MUSIC, MOVIE or TEXT.
1 Pressing Ż/Ź buttons you can change between
want to search the files and then press OK.
2 Press Ÿ/ź/Ż/Ź to select the folder where you
You can reproduce photos with JPEG (*.JPE, *.JPG),
BMP and PNG format on your TV.
Several kinds of reproduction are possible.
1 Select PHOTO mode and press OK.
2 Select the file you want to display on full screen
with Ÿ/ź /Ż/Ź buttons and press OK to start the
supplied with the wall fix bracket to secure the bracket to the rear of the TV.
• You can ask qualified service personnel about using an optional bracket to fix the TV on a wall.
• To use this TV fixed on a wall, first remove the adhesive tape at the two locations on the rear of the TV, and then use the screws
• When you fix the TV on a wall, you should attach the supporting post.
Setting when using external
Other useful features
Input source settings
devices
For selecting the input type of external equipment.
(Media Player)
Connecting a USB device
another signal type.
for the signal type.
• If no (colour) image is displayed, try changing to
• Check the operations manual of the external equipment
Connect an USB device to the TV as shown below.
9
able to recognise the contained data.
on character set) may not be displayed.
the TV while transferring files, using the slide show
function, when a screen is switching to another or
before you exit “MEDIA PLAYER” from the “INPUT
SOURCE” menu.
• Depending on the USB device, the TV may not be
• Use only alphanumeric characters for naming files.
• File names over 80 characters (may vary depending
• Do not disconnect a USB device or memory card from
the TV repeatedly.
• Compatibility with USB hard disc connection.
• Do not connect and disconnect a USB device from
LC-32LE210 LC-32LE220
DIMENSIONS
536
501
35
700.7
787
418
200
395.4
294.6
91
45
66.4
238
100
60
10
REMOVING OF MAJOR PARTS
LC-32LE210 LC-32LE220
1. To slacken the 4 lock screws and detach the Stand.
2. Remove the 2 lock screws , 2 lock screws , 1 lock screws , 6 lock screws , 1 lock screw and detach the Rear Cabinet.
1
2
3
4
5
6
4
Rear
6
5
Cabinet
2
3
Stand
Front Cabinet
1
11
LC-32LE210 LC-32LE220
Removing of major parts (Continued)
3. Disconnect all the connectors from all the PWBs.
4. Remove the Key Unit Ass’y
LC32LE210E & LC32Lx220E models:
7
.
Control cover
7
Control button
[KM]
KEY UNIT
[L1]
[L2]
[PD]
SP-R
LC32LE210EB & LC32Lx220EB models:
[LV]
[LV]
[RA]
[KM]
[LV]
[PD]
[RA]
[SP]
SP-L
Control cover
[KM]
7
Control button
KEY UNIT
SP-R
[LA]
[PD]
[LA]
[RA]
[LV]
[PD]
[RA]
12
[SP]
SP-L
[KM]
Removing of major parts (Continued)
LC-32LE210 LC-32LE220
5. Remove the speaker (R) , (L) .
6. Remove the 5 lock screws , 1 lock screw and detach the POWER Unit
7. Remove the 4 lock screws , and detach the MAIN Unit.
8. Remove the LED PWB .
8
10
12
13
9
11
LC32LE210E & LC32Lx220E models:
10
POWER Unit
MAIN Unit
11
12
.
8
Speaker (R)
LC32LE210EB & LC32Lx220EB models:
10
POWER Unit
11
LED PWB
Speaker (L)
13
MAIN Unit
9
12
8
Speaker (R)
LED PWB
13
Speaker (L)
13
9
LC-32LE210 LC-32LE220
Removing of major parts (Continued)
9. Remove the 6 lock screws and detach the stand angle.
10. Remove the 8 lock screws and detach the panel brackets.
14
15
LC32LE210E & LC32Lx220E models:
15 15
15
Panel Bracket CENTER
Panel Bracket
CENTER
15
Panel Bracket BOTTOM
15
Panel Brackets TOP
Panel Brackets CENTER
Panel Bracket BOTTOM
15
15
15
LC32LE210EB & LC32Lx220EB models:
15
Panel Bracket CENTER
Panel Bracket
CENTER
15
Panel Bracket BOTTOM
15
Stand angle
15
Panel Bracket TOP RIGHT
15
Panel Bracket TOP LEFT
14
14
Panel Brackets CENTER
Panel Bracket BOTTOM
15
15
15
14
14
14
Removing of major parts (Continued)
LC-32LE210 LC-32LE220
11. Remove the 4 lock screws and detach the angles.
12. Remove the insulation sheet .
LC32LE210E & LC32Lx220E models:
16
17
16
17
LC32LE210EB & LC32Lx220EB models:
16
17
15
LC-32LE210 LC-32LE220
SERVICE ADJUSTMENTS
1. Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum performance at the time of shipment from the factory.
If any value should become improper or any adjustment is necessary due to the part replacement, make an adjust-
ment according to the following procedure.
1.1. Procure the following units in order to replace the main unit:
MAIN UNIT DUNTKF639FMxx
NOTE: [Caution when replacing ICs in the main unit (IC1901, IC1902, IC1902, IC1501, IC1006 and IC1007)]
Before replacing the relevant part, procure the following parts in which the data have been rewritten.
Ref. Description Parts code IC + data Description new IC code for service
IC1901 HDMI EDID 1 RH-IXD236WJZZY RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_1_EDID
IC1902 HDMI EDID 2 RH-IXD237WJZZY RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_2_EDID
IC1903 HDMI EDID 3 RH-IXD238WJZZY RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_3_EDID
IC1501 PC EDID RH-IXD239WJZZY RH-IXD080WJZZY AND DATA LC32LE2x0E_PC_EDID
IC1006 HDCP USER SETTINGS RH-IXD261WJZZY RH-IXC986WJZZY AND DATA LC32LE2x0E_HDCP_KEY
IC1007
*
FLASH MEMORY
RH-IXD262WJZZY RH-IXD012WJZZY and LE210_v1.25_PANEL_AUO_BOARD_N1
RH-IXD263WJZZY RH-IXD012WJZZY and LE210B_v1.25_PANEL_CMI_BOARD_N1
* For Lx220 models it is not possible replace IC1007. Replace the full Main Unit.
2. Entering and exiting the adjustment process mode. Standard method.
1. By key-unit.
1. Unplug the AC power cord.
2. Press and hold “V-” and “b” keys, simultaneously, and then plug the AC power cord.
3. “K” appears on the screen.
4. Press and hold “V-” and “P-” keys, simultaneously.
5. “SHARP FACTORY MENU” appears (see Figure 1).
6. Unplug the AC power cord to exit of adjustments process.
2. By own R/C
1. Turn on the TV set.
2. Press “b”,”2”,”5”, “8”, “0” (the time is limited to 5 sec. approx., for enter this code).
3. “SHARP FACTORY MENU” appears (see Figure 1).
4. Press “OK” on lines 5 ~ 12 to go to submenu.
5. Press “MENU” to return to main menu.
6. Press “END” to exit of adjustments mode.
16
LC-32LE210 LC-32LE220
3. Remote control key operation and description of display in adjustment process mode.
1. key operation
Remote control key Keyboard unit Function
Cursor (ź/Ÿ ) P (
s/r) Moving an item (line) by one (up/down) on “Sharp Factory Menu”
or submenus.
OK
b
Selecting a submenu on lines 5 to 12 of “Sharp Factory Menu” or executing a function.
Cursor (Ż/Ź) V (+/-) Changing a selected item setting value.
MENU MENU Return to “Sharp Factory Menu” from a submenu.
The required input mode should be switched previously to enter the Service Mode.
CAUTION: Use due care in handling the information described here lest the users should know how to enter the
adjustment process mode. If the settings are tampered with in this mode, unrecoverable system
damage may result.
4. Description of display
Figure 1: Main Service Adjustment Menu
SHARP FACTORY MENU
Main version 32LE210E SHARP v1.25 SEES v89 MSTAR CL308413
Bootloader version BD_MST064E_C01A 2
Normal standby cause Remote control
Error standby cause None
INIT
ADJUST
ETC
PUBLIC MODE
SMARTLOADER
ADC ADJUST
GAMMA
SYSTEM INFORMATION
(1)
ĸ Informative (Main microprocessor version).
ĸ Informative.
ĸ Informative (Remote Control/Keyboard…).
ĸ Informative (None/Lamp Error).
ĸ Press “OK” to go to INIT submenu.
ĸ Press “OK” to go to ADJUST submenu.
ĸ Press “OK” to go to ETC submenu.
ĸ Press “OK” to go to PUBLIC MODE submenu.
ĸ Press “OK” to go to SMARTLOADER submenu.
ĸ Press “OK” to go to ADC ADJUST submenu.
ĸ Press “OK” to go to GAMMA submenu.
ĸ Press “OK” to go to SYSTEM INFORMATION submenu.
(2) (3)
No. Description Display speci cation
(1) Service Information Current Software version and others.
(2) Item name Submenus to be checked or adjusted (by pressing “OK” button)
(3) Factory init and Inch setting Are shown on INIT submenu
17
LC-32LE210 LC-32LE220
5. Adjustment process mode menu
Page Line Sub
Page
01/17 [SHARP FACTORY MENU
1 Main Version 32LE210E SHARP v1.25 SEES
2 Bootloader Version BD_MST064E_C01A 2 Informative only
3 Normal Standby Cause
4 Error Standby Cause None / Lamp Error Informative only
5 INIT Factory Init Submenu Press “OK” to enter to Factory Init Submenu
02/17 Factory Init EURO I
6 ADJUST QMAP ADJUST Submenu Press “OK” to enter to QMAP ADJUST Submenu
03/17 INPUT SOURCE (1/6) RF_PAL_BGHI
04/17 INPUT SOURCE (2/6) DTV/ RF/Multimedia ...
05/17 INPUT SOURCE (3/6) DTV/ RF/Multimedia ...
Item Description Remarks (adjustment details, etc.)
Inch Setting AV32_T315HW05V3 Panel type
Center Acutime 0 H 0 M Backlight ON accumulated Time
RESET “OK” Will be displayed
AFEC Only for Engineering purpose (Please don’t use)
Comb Only for Engineering purpose (Please don’t use)
SECAM Only for Engineering purpose (Please don’t use)
SCinit Only for Engineering purpose (Please don’t use)
CSC OFF Only for Engineering purpose (Please don’t use)
CSC_Dither OFF Only for Engineering purpose (Please don’t use)
YCdelay OFF Only for Engineering purpose (Please don’t use)
PreFilter OFF Only for Engineering purpose (Please don’t use)
HSD_Y ALL PASS1X Only for Engineering purpose (Please don’t use)
HSD_C ALL PASS1X Only for Engineering purpose (Please don’t use)
VSD OFF Only for Engineering purpose (Please don’t use)
CTI CTI_1 Only for Engineering purpose (Please don’t use)
MemFormat 422MF Only for Engineering purpose (Please don’t use)
444To422 ON Only for Engineering purpose (Please don’t use)
PreSNR OFF Only for Engineering purpose (Please don’t use)
DNR NR_OFF Only for Engineering purpose (Please don’t use)
DNR_Motion MR_NR Only for Engineering purpose (Please don’t use)
DNR_Y OFF Only for Engineering purpose (Please don’t use)
DNR_MED OFF Only for Engineering purpose (Please don’t use)
DNR_C OFF Only for Engineering purpose (Please don’t use)
PNR OFF Only for Engineering purpose (Please don’t use)
PNR_Y OFF Only for Engineering purpose (Please don’t use)
PNR_C OFF Only for Engineering purpose (Please don’t use)
PostCCS OFF Only for Engineering purpose (Please don’t use)
PostCCS_Smooth PCS_6 Only for Engineering purpose (Please don’t use)
420CUP OFF Only for Engineering purpose (Please don’t use)
MADi 25_4R Only for Engineering purpose (Please don’t use)
MADi_Motion MOT_PMODE Only for Engineering purpose (Please don’t use)
MADi_ADP3x3 OFF Only for Engineering purpose (Please don’t use)
MADi_MORPHO OFF Only for Engineering purpose (Please don’t use)
MADi_DFK OFF Only for Engineering purpose (Please don’t use)
v89 MSTAR CL308413
Remote Control / Keyboard...
Informative only (Main microprocessor version)
Informative only
nformative (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE)
Press “Ż “ or “ Ź” to reset Center Acutime
18
LC-32LE210 LC-32LE220
Page Line Sub
Page
1/17 [SHARP FACTORY MENU
6 ADJUST (continued) QMAP ADJUST Submenu Press “OK” to enter to QMAP ADJUST Submenu
05/17 INPUT SOURCE (3/6) DTV/ RF/Multimedia ...
06/17 INPUT SOURCE (4/6) DTV/ RF/Multimedia ...
07/17 INPUT SOURCE (5/6) DTV/ RF/Multimedia ...
08/17 INPUT SOURCE (6/6) DTV/ RF/Multimedia ...
Item Description Remarks (adjustment details, etc.)
MADi_SST OFF Only for Engineering purpose (Please don’t use)
MADi_Force OFF Only for Engineering purpose (Please don’t use)
EODi OFF Only for Engineering purpose (Please don’t use)
Film SD_2 Only for Engineering purpose (Please don’t use)
Film32 OFF Only for Engineering purpose (Please don’t use)
Film22 OFF Only for Engineering purpose (Please don’t use)
DIPF OFF Only for Engineering purpose (Please don’t use)
VCLPF ON Only for Engineering purpose (Please don’t use)
Spike_NR S2 Only for Engineering purpose (Please don’t use)
SPF ON Only for Engineering purpose (Please don’t use)
SPF_DBK OFF Only for Engineering purpose (Please don’t use)
SPF_SNR E2S1 Only for Engineering purpose (Please don’t use)
SPF_DBK_SNR_MR ON Only for Engineering purpose (Please don’t use)
SPF_MR_LPF LPF3x3 Only for Engineering purpose (Please don’t use)
SPF_SMR S2 Only for Engineering purpose (Please don’t use)
SPF_NMR_MR ON Only for Engineering purpose (Please don’t use)
DMS S2 Only for Engineering purpose (Please don’t use)
VSP_Y SRAM_1_4Tap Only for Engineering purpose (Please don’t use)
VSP_C ROM_2121 Only for Engineering purpose (Please don’t use)
VSP_CoRing OFF Only for Engineering purpose (Please don’t use)
VSP_DeRing OFF Only for Engineering purpose (Please don’t use)
VSP_Dither OFF Only for Engineering purpose (Please don’t use)
VSP_PreVBound OFF Only for Engineering purpose (Please don’t use)
HSP_Y SRAM_2_6Tap Only for Engineering purpose (Please don’t use)
HSP_C ROM_121 Only for Engineering purpose (Please don’t use)
HSP_CoRing Y_Coring_1 Only for Engineering purpose (Please don’t use)
HSP_DeRing OFF Only for Engineering purpose (Please don’t use)
HSP_Dither OFF Only for Engineering purpose (Please don’t use)
HnonLinear H_1920_0 Only for Engineering purpose (Please don’t use)
SRAM1
SRAM2
422To444 ON Only for Engineering purpose (Please don’t use)
Peaking 1080p Only for Engineering purpose (Please don’t use)
SwDriver ALL Only for Engineering purpose (Please don’t use)
VIP_CSC OFF Only for Engineering purpose (Please don’t use)
VIP_CSC_Dither OFF Only for Engineering purpose (Please don’t use)
Color Multimedia_photo_HD Only for Engineering purpose (Please don’t use)
3x3 OFF Only for Engineering purpose (Please don’t use)
Display ALL Only for Engineering purpose (Please don’t use)
Post_CON_BRI OFF Only for Engineering purpose (Please don’t use)
lnvSinc4Tc4p4Fc85
Fstop134Apass01Astop50
lnvSinc6Tc4p4Fc94
Fstop134Apass01Astop
60
Only for Engineering purpose (Please don’t use)
Only for Engineering purpose (Please don’t use)
19
LC-32LE210 LC-32LE220
Page Line Sub
Page
01/17 [SHARP FACTORY MENU
7 ETC EEP, Autoinstallation, Op-
09/17 EEP Clear
8 PUBLIC MODE (1/2) PUBLIC MODE Submenu Press “OK” to enter to PUBLIC MODE Sub-
10/17 Power On  xed Variable
11/17 Hotel mode Off
Item Description Remarks (adjustment details, etc.)
EEP Clear B
Standby cause reset “OK“ will be displayed
Autoinstallation SW Off
Pattern 0 Selection of internal pattern from 0 up to 6…
L Error Reset 0
L Error Check On L_ERR detection. ON: activated. OFF: deactivated.
I2C OFF Off I2C BUS status. On: free BUS. Off: Normal.
Sharp protocol On Remote Control Protocol. On: SHARP Off: MSTAR.
Maximum volume 60
Volume  xed Variable
Volume  xed Level 20
RC button Respond
Panel button Respond
Menu button Respond
On screen display On
Input mode start Normal
Input mode  xed Variable
Input TV mode program number
RC path through Off
PUBLIC MODE (2/2) PUBLIC MODE Submenu
Reset “OK“ will be displayed
tion, Country, L Error...
Normal
Press “OK” to enter to ETC Submenu
Ź” to Clear NVM data
Press “
Press “
Ź” to Clear NVM data (except adjustments area).
Press “
Ź” to Reset of STANDBY CAUSE.
On: Pending to execute on next power on. Off: Not required.
Press “
Ź” to LAMP ERR RESET. Initialization of L_ERR.
menu
Ż” or “Ź” to change Variable/Fixed.
Press “
Ż” or “Ź” to change 0/60.
Press “
Press “
Ż” or “Ź” to change Variable/Fixed.
Press “
Ż” or “Ź” to change 0/60.
Ż” or “Ź” to change Respond/No respond.
Press “
Press “
Ż” or “Ź” to change Respond/No respond.
Ż” or “Ź” to change Respond/No respond.
Press “
Press “
Ż” or “Ź” to change On/Off.
Ż” or “Ź” to change Normal/TV/SCART/…
Press “
Press “
Ż” or “Ź” to change Variable/Fixed.
Press “
Ż” or “Ź” to change Normal ĺ 1 ĺ 2 ...999
ĺ Normal).
Press “Ż” or “Ź” to change On/Off (required external module)
Ż” or “Ź” to change On/Off.
Press “
Press “
Ż” or “Ź” to return to factory settings.
Execute “OK“ will be displayed
9 SMART LOADER SMART LOADER Sub-
menu
12/17 Save settings to USB (“OK“ or “NO USB drive
available, please check and/or insert USB dri...”
will be displayed).
Load settings from USB (“OK, reboot TV set“ or
“NO USB drive available, please check and/or in­sert USB dri...” will be dis-
played).
10 ADC ADJUST ADC ADJUST Submenu Press “OK” to enter to ADC ADJUST Submenu
13/17 MODE YPbPr(SD)
ADJUST External signal
R-GAIN 80
G-GAIN 70
Ż” or “Ź” to confirm.
Press “
Press “OK” to enter to SMART LOADER Sub­menu
Press “
Ż” or “Ź” to Save.
“OK” or “NO USB drive available, please check
( and/or insert USB dri…” will be displayed).
Press “Ż” or “Ź” to Load.
Press “Ż” or “Ź” to change RGB/YPbPr(SD)/ YPbPr(HD).
Press “Ż” or “Ź” to change Internal signal/External signal. External: factory. Internal: service
Press “
Ż” or “Ź” for manual adjustment.
Ż” or “Ź” for manual adjustment.
Press “
20
LC-32LE210 LC-32LE220
Page Line Sub
Item Description Remarks (adjustment details, etc.)
Page
01/17 [SHARP FACTORY MENU
ADC ADJUST (continued)
10 13/17 B-GAIN 80 Press “Ż” or “Ź” for manual adjustment.
R-OFFSET 128 Press “Ż” or “Ź” for manual adjustment.
G-OFFSET 128 Press “Ż” or “Ź” for manual adjustment.
B-OFFSET 128 Press “Ż” or “Ź” for manual adjustment.
AUTO ADC
11 GAMMA (1/3) GAMMA Submenu Press “OK” to enter to GAMMA Submenu
14/17 MGAMMA IN1 40 W/B adjustment, gradation 1 input setting.
MGAMMA IN2 80 W/B adjustment, gradation 2 input setting.
MGAMMA IN3 120 W/B adjustment, gradation 3 input setting.
MGAMMA IN4 160 W/B adjustment, gradation 4 input setting.
MGAMMA IN5 200 W/B adjustment, gradation 5 input setting.
MGAMMA IN6 240 W/B adjustment, gradation 6 input setting.
MGAMMA WRITE
MGAMMA RESET
GAMMA (2/3) GAMMA Submenu
15/17 MGAMMA R1 151 W/B adjustment, gradation 1R adjustment value.
MGAMMA G1 155 W/B adjustment, gradation 1G adjustment value.
MGAMMA B1 146 W/B adjustment, gradation 1B adjustment value.
MGAMMA R2 307 W/B adjustment, gradation 2R adjustment value.
MGAMMA G2 318 W/B adjustment, gradation 2G adjustment value.
MGAMMA B2 308 W/B adjustment, gradation 2B adjustment value.
MGAMMA R3 458 W/B adjustment, gradation 3R adjustment value.
MGAMMA G3 480 W/B adjustment, gradation 3G adjustment value.
MGAMMA B3 471 W/B adjustment, gradation 3R adjustment value.
MGAMMA WRITE
GAMMA (3/3) W/B ADJUST Submenu
16/17 MGAMMA R4 619 W/B adjustment, gradation 4R adjustment value.
MGAMMA G4 640 W/B adjustment, gradation 4G adjustment value.
ADC ADJUST Submenu Press “OK” to enter to ADC ADJUST Submenu
“SUCCESS” or ”Fail will be displayed
“SUCCESS” will be displayed
“SUCCESS” will be displayed
“SUCCESS” will be displayed
Press “Ż” or “Ź” for automatic adjustment in each mode.
Press “Ż” or “Ź” for EEP writing of adjustment values.
Press “Ż” or “Ź” for Initialization of adjustment values.
Press “Ż” or “Ź” for EEP writing of adjustment values.
MGAMMA B4 631 W/B adjustment, gradation 4B adjustment value.
MGAMMA R5 770 W/B adjustment, gradation 5R adjustment value.
MGAMMA G5 800 W/B adjustment, gradation 5G adjustment value.
MGAMMA B5 789 W/B adjustment, gradation 5B adjustment value.
MGAMMA R6 918 W/B adjustment, gradation 6R adjustment value.
MGAMMA G6 961 W/B adjustment, gradation 6G adjustment value.
MGAMMA B6 946 W/B adjustment, gradation 6R adjustment value.
MGAMMA WRITE
12
17/17 NOISE LEVEL 8 Informative (changing).
SYSTEM INFORMATION
GLOBAL MOTION 127 Informative (changing).
BIT RATE 0 Informative.
Scan name search 2 Changeable between 0 and 255.
VPS code FFFF Informative.
830/1 code FFFF Informative.
830/2 code FFFF Informative.
Top TXT enabled 1 Press “Ż” or “Ź” to change 0/1.
CEC off Press “Ż” or “Ź” to change off/on.
“SUCCESS” will be displayed
SYSTEM INFORMATION
Submenu
Press “Ż” or “Ź” for EEP writing of adjustment values.
Press “OK” to enter to SYSTEM INFORMATION Sub­menu (Only for Engineering purpose, don’t use)
21
LC-32LE210 LC-32LE220
6. Video Signal Adjustment Procedure
6.1. RGB SCART ADC
1. Enter in Service mode.
2. Press “ź” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “ź” until selecting “ADJUST” option.
6. Press “Ź”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “Ź”until selecting “RGB”.
9. Press “ź” until selecting “AUTO ADC” option.
10. Press “Ź”, the adjustment starts.
11. “SUCCESS” appears when the adjustments  nish.
12. Exit of Service mode.
6.2. COMPONENTS ADC
1. Enter in Service mode.
2. Press “ź” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “ź” until selecting “ADJUST” option.
6. Press “Ź”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “Ź”until selecting “YPbPr(SD)” or “YPbPr(HD)”
9. Press “ź” until selecting “AUTO ADC” option.
10. Press “Ź”, the adjustment starts.
11. “SUCCESS” appears when the adjustments  nish.
Note: both SD and HD are adjusted.
12. Exit of Service mode.
6.3. PC IN RGB ADC
1. Enter in Service mode.
2. Press “ź” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “ź” until selecting “ADJUST” option.
6. Press “Ź”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “Ź”until selecting “PC-RGB”.
9. Press “ź” until selecting “AUTO ADC” option.
10. Press “Ź”, the adjustment starts.
11. “SUCCESS” appears when the adjustments  nish.
12. Exit of Service mode.
22
7. White Balance Adjustment
Condition: AV MODE= Dynamic (backlight at max.).
• Adjustments reference device: Minolta CA-210
• Adjustments target: x=0.272, y=0.277
High: adjustments spec ±0.001, inspection spec: ±0.002
Low: adjustments spec ±0.002, inspection spec: ±0.004
1. Press “ź” until selecting “GAMMA” option.
2. Press “OK”.
3. “GAMMA” menu appears.
4. Press “ź” until selecting “MGAMMA RESET”.
5. Press “Ź”, to restore default values.
6. “MGAMMA RESET SUCCESS” appears.
7. Press “P+” to increase one page.
8. Press “1”, appears “Internal Adjustments Pattern 1”.
9. Hold the default value for “MGAMMA G1”.
(Note: next, try to get the (x, y) adjustments target,
changing “MGAMMA R1” and “MGAMMA B1” as follow).
10. Press “ź” until selecting “MGAMMA R1”.
11. Press “
12. Press “MENU” to return to previous menu.
13. Press “ź” until selecting “MGAMMA B1”.
14. Press “
15. Press “MENU” to return to previous menu.
(Note: In case of not being possible to achieve the desired
(x, y) target, try to get it by changing also the “MGAMMA G1”)
16. Press “2”, appears “Internal Adjustments Pattern 2”.
17. Repeat from step 9 to 15 for the “MGAMMA R2” and “MGAMMA B2”.
18. Press “3”, appears “Internal Adjustments Pattern 3”.
19. Repeat from step 9 to 15 for the “MGAMMA R3” and “MGAMMA B3”.
20. Press “4”, appears “Internal Adjustments Pattern 4”.
21. Repeat from step 9 to 15 for the “MGAMMA R4” and “MGAMMA B4”.
22. Press “5”, appears “Internal Adjustments Pattern 5”.
23. Repeat from step 9 to 15 for the “MGAMMA R5” and “MGAMMA B5”.
24. Press “6”, appears “Internal Adjustments Pattern 6”.
25. Repeat from step 9 to 15 for the “MGAMMA R6” and “MGAMMA B6”.
26. Press “ź” until selecting “MGAMMA WRITE”.
27. Press “Ź”, to save the new values.
28. “MGAMMA WRITE SUCCESS” appears.
Ż
Ź” until you obtain the desired value.
Ż
Ź” until you obtain the desired value.
LC-32LE210 LC-32LE220
NOTE:
For activating the W/B  ag, only is necessary to send the order MGAMMA WRITE. After this action, the “W” W/B  ag will change to “1”.
23
LC-32LE210 LC-32LE220
8. Initialization to factory setting
Caution: When the factory settings have been made, all user setting data, including the channel settings, are initialized. (The
adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.
1. Enter in Service mode.
2. Press “ź” or “Ÿ” key until selecting INIT.
3. Press OK key.
4. INIT menu appears and “Factory init” option is selected.
5. Press “
6. Press OK key and initialization starts.
7. OK, EURO message appears for EURO option when the setting is complete. OK, RUSSIA message appears for RUSSIA option when the setting is complete. OK, SWEDEN message appears for SWEDEN option when the setting is complete. OK, UK message appears for UK option when the setting is complete. OK, EAST EUROPE message appears for EAST EUROPE option when the setting is complete.
Note: Never turn the power off during initialization.
To exit the adjustment process mode, unplug the AC power cord from the outlet to forcibly turn off the power.
Ż
” or “Ź” until selecting the option desired (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE).
The following settings will be back to their factory ones.
• User settings
• Channel data (e.g. broadcast frequencies)
• Maker option setting
• Password data
24
LC-32LE210 LC-32LE220
9. Lamp error detection
1. Function description
This LCD colour television has a function (lamp error detection) to be turned OFF the TV set automatically for safety criteria when the lamp or lamp circuit is abnormal.
If the lamp or lamp circuit is abnormal, or some other errors happen, and the lamp error detection is executed, the following occurs:
a. The TV set is turned OFF automatically 20 seconds after it is turned ON by the user.
(The power LED on the front side of TV turns from green to red)
b. If the situation “a.” happens 5 times sequentially, it becomes impossible to turn on the power.
(The power LED turns from green to red and keeps blinking in red).
LED Flashing timing
1 s Red ĺ 260 ms
Off ĺ 1s
260 ms
2. Countermeasures
a. Checking with [L Error Check Off]. Repair the problem that produces the LAMP ERROR. The TV remains with power LED blinking until K mode is forced by local keyboard, in order to disable the LAMP ERROR detec­tion. To disable the LAMP ERROR feature is necessary enter in K mode by pressing “VOL DOWN” and “b” keys at same time when the AC cord is plugged in.
b. Resetting the LAMP ERROR counter. After the lamp and lamp circuit are found out of trouble, the LAMP ERROR counter should be reset. If a LAMP ERROR is detected  ve consecutive times, the power cannot be turned on.
Method 1: Using the cursor (UP/DOWN) key, move to the cursor to [L Error Reset] on Line 6 of ETC Menu Fig
4. With the cursor (LEFT/RIGHT) keys reset the value to “0”.
Method 2: In the case the TV is not blocked (less than 5 consecutive errors), switch on the Set. After 30 minutes
working, the LAMP ERROR counter will be reset automatically.
25
LC-32LE210 LC-32LE220
10. Public Mode (Hotel mode)
1. How to Enter in the Public Mode (Hotel Mode).
There are three following ways to display the Public Mode setting screen.
Method 1:
Turn on the power and enter in the Service mode as usual and select line 8 [PUBLIC MODE].
Method 2:
Unplug the AC power cord. While pressing “VOL+” and “b” keys at the same time, plug the AC power cord. Then, when you are asked for the password, enter “0027”. After this sequence the TV will turn on showing the Public Mode setting screen as it is shown in Fig. 5. In another case, the screen is erased, and it operates in the ordinary mode.
Method 3:
By special R/C code: RC table LCD, SYS CORD: 0x78, RC DATA: (HEX) 0xC7, (DEC) 199. Then, when you are asked for the password, enter “0027”. After this sequence the TV will turn on showing the Public Mode setting screen as it is shown in Fig. 5.
Is possible to select each item of function by pressing cursor UP/DOWN keys on the remote control or CH (UP/ DOWN) keys on the LCD TV.
The setting position of each item of functions is made by pressing cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV.
Set to ON the HOTEL MODE function to active it.
Select EXECUTE position after you set all function, and press cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV for con rmation.
Unplug and plug the AC power cord to take effect all the changes.
2. Public Mode Settings.
1. POWER ON FIXED [VARIABLEļFIXED] When it is set to “FIXED” the TV is impossible to be switch off by Main Switch or Remote Control.
2. MAXIMUM VOLUME [0 ļ 60] Is possible to set the maximum volume at limited level.
3. VOLUME FIXED [VARIABLE ļ FIXED] Is possible to  x the sound volume at limited level. When “FIXED” is selected the sound volume before limited is  xed.
4. VOLUME FIXED LEVEL [0 ļ 60]
If “FIXED” has been selected, is possible to set a  xed volume at the level that is chosen.
5. RC BUTTON [RESPOND ļ NO RESPOND] If “NO RESPOND” is selected, the remote control keys are inoperative.
6. PANEL BUTTON [RESPOND ļ NO RESPOND]
If “NO RESPOND” has been selected, the set’s keys remain deactivated (Except POWER key).
7. MENU BUTTON [RESPOND ļ NO RESPOND] If “NO RESPOND” has been selected, “MENU” key, of remote control, is inoperative.
26
LC-32LE210 LC-32LE220
10. Public Mode (Hotel mode) (continued)
8. ON SCREEN DISPLAY [On ļ Off]
If “NO” has been selected, the On Screen Display does not appear.
9. INPUT MODE START [NORMAL ĺ TV ĺ SCART ĺ COMPONENTS ĺ HDMI1 ĺ HDMI2 ĺ HDMI3 ĺ AV
ĺMEDIA PLAYER]
When any other item than “NORMAL” has been selected, the sets will start in a selected input mode at the
next power-on.
10. INPUT MODE FIXED [VARIABLE ĺ FIXED] “FIXED” has been selected, any channels and input modes other than those selected at the start mode cannot
be picked up.
11. INPUT TV MODE PROGRAM NUMBER [NORMAL ĺ 1-999 ĺ NORMAL] When any other item than “NORMAL”, i.e. number, has been selected, and “INPUT MODE START” option is
set to “TV”, the sets will start in the selected service / program number at the next power-on.
12. RC PATH THROUGH [ON ļ OFF] T.B.D.
13. HOTEL MODE [ON ļ OFF] If ON has been selected the HOTEL MODE is activated.
14. RESET Cancel all Public Mode settings. (It returns to the factory settings)
15. EXECUTE Select this item, and press cursor RIGHT / LEFT keys on the remote control or VOL (+) / (-) keys on the LCD
TV for con rmation the functions settings.
11. SMART LOADER
Description.
The Smartloader is a function implemented in the service software of SEES designed LE200 series intended to easily replicate the user settings of one TV into another. These settings include (but not restricted to): picture and audio, tun­ing set-up, language and country selection, PIN, child locked programs… Factory adjustments are not copied as they are different for every TV. The Smartloader makes possible the user data to be stored in a memory device connected to the USB terminal of the TV that is used as reference and later load those data into other TVs by using their respective USB terminal.
How it works.
In reference TV:
1. Insert a memory device in the USB slot.
2. Enter in service mode, select Factory Menu and SMARTLOADER option.
3. Select “Save settings to USB” and press the RIGHT cursor in the remote control.
4. Wait until “OK” is displayed, the  le has been successfully created in the root directory of the memory device. In case of error, an explanation message is shown.
In TV to be cloned:
1. Insert a memory device with a  le in it obtained following the above procedure.
2. Enter in service mode, select Factory Menu and SMARTLOADER option.
3. Select “Load settings from USB” and press the RIGHT button in the remote control.
4. After some seconds, “OK, reboot TV set” is displayed. In case of error, an explanation message is shown.
5. As indicated, reboot the TV to load the new settings.
Very important: All the TVs must have the same software version and hardware.
27
LC-32LE210
Ɣ
Ɣ
Ɣ
Ɣ
LC-32LE220
SOFTWARE UPDATING
1. Introduction
1. In order to proceed with the Software Updating do not enter into Service Mode.
2. The TV should be in normal operation (ON).
2. Procedure
1. Insert the USB memory into the USB terminal with the  le name “MERGE.bin”(for LE210) or “MERGE_aes.bin”(for Lx220) on the root directory.
2. Press “MENU”.
• “PICTURE” menu appears on screen.
3. Press “Ź” until selecting “OPTION” menu.
4. Press “ź” until selecting “Software update (USB) Sharp v*.*”.
• The current software version is displayed.
5. Press “OK”
• “Are you sure? Yes - No” message is displayed.
6. Press “Ż” until selecting “Yes”.
7. Press “OK”.
• The software update process starts.
• “Software upgrading… **%” message appears.
• The upgrading process is  nished, the LCD-TV restarts.
NOTE: If the “MERGE.bin” (for LE210) or “MERGE_aes.bin”(for Lx220) on the USB memory is not the proper
for this model, an ERROR message is shown on screen and the LCD TV restarts itself. No upgrade is made.
8. Remove the AC cord and plug it again.
9. Return to OPTION menu to check that the version has been updated successfully.
NOTE:
If the TV is switched off during the upgrade process, when it is switched on again, the Power LED  ashes: Violet for 130 ms and blue for 1.5 s, with NO screen until it is detected in the USB memory a  le “MERGE.bin”(for
LE210) or “MERGE_aes.bin” (for Lx220). Then the power LED will  ash: Violet for 40 ms and blue for other 40 ms, with NO screen while the new software is uploaded.
Once the process is completed, the TV set will start automatically.
28
Loading...
+ 64 hidden pages