Page 1
Preparation
Installing Batteries in the Remote Control
Before using the LCD TV set for the first time, install the two R-03 (“AAA” size, UM/SUM-4) batteries supplied in the remote
control. When the batteries become depleted and the remote control fails to operate, replace the batteries with new R-03
(“AAA” size, UM/SUM-4) batteries.
1 Open the battery cover. 2 Insert two R-03 (“AAA” size,
UM/SUM-4) batteries.
■ Slide the cover while
pressing the ([) part.
■ Position the positive and
negative ends of the
batteries as indicated in
the compartment.
3 Replace the battery cover.
■ Engaging the lower
claw with the remote
control, close the
cover.
Caution!
Precautions regarding batteries
■ Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) indications.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old
batteries to leak chemicals.
• Remove batteries as soon as they are depleted. Chemicals that leak from batteries can cause a rash. If chemical
leakage is found, wipe it off with a cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control is not to be used for an extended period of time, remove the batteries from the remote control.
Using Remote Control
■ Use the remote control by pointing it towards the remote sensor
window of the main unit. Objects between the remote control and
sensor window may prevent proper operation.
Cautions regarding use of remote control
■ Do not expose the remote control to shock. In addition, do not
expose the remote control to liquids, and do not place it in an area
with high humidity.
■ Do not install or place the remote control under direct sunlight. The
heat may cause deformation of the unit.
■ The remote control may not work properly if the remote sensor
window is under direct sunlight or strong lighting. In such a case,
change the angle of the lighting or main unit, or operate the remote
control closer to the remote sensor window.
OPC
Remote sensor indicator
OPC indicator
Power/Standby indicator
OPC sensor window
Remote sensor window
5
Page 2
Preparation (Continued)
Connect to the DC input terminal of the product.
Pull down the
hook to open
the cover.
(MAIN POWER)
T
OU
IO
D
U
A
L
R
Power Connection
Pull down the
hook to open
the cover.
1
V-IN
A
B
G
R
2
V-IN
A
O
E
ID
-V
S
O
IDE
V
L
IO
D
U
A
R
R
E
W
O
P
T
U
P
IN
V
3
1
C
D
Household
power outlet
To POWER INPUT
terminal
Plug into an AC outlet.
AC adapter
AC cord*
* Product shape varies in some countries.
Note:
Note:
• Always turn the (MAIN POWER) switch of the LCD TV set to OFF when connecting the AC adapter.
• Unplug the AC adapter from the LCD TV set and power outlet when the LCD TV set is not to be used for a long period of time.
Antenna Connection
To enjoy a clearer picture, we recommend that you use
an outdoor antenna. The following is a brief explanation
of the types of connection that are used for coaxial and
feeder cables:
(1)If your outdoor antenna uses a 75-ohm coaxial
cable, change this for a new standard DIN45325
(IEC169-2) plug and plug it into the antenna
terminal at the back of TV set via the antenna cable
(not supplied).
(2)If your outdoor antenna uses a 300-ohm twin-lead
flat feeder, change this for a 300-ohm to 75-ohm
impedance converter and plug it into the antenna
terminal at the back of TV set via the antenna cable
(not supplied).
75-ohm coaxial cable (round cable)
AUDIO OUT
L
R
-IN
V
A
B
G
R
2
-IN
V
A
O
E
ID
-V
S
O
E
ID
V
L
IO
D
U
A
R
R
E
W
O
P
T
U
P
IN
3V
1
C
D
1
6
To antenna
input terminal
( )
300-ohm twin-lead flat feeder
Page 3
Preparation (Continued)
First Installation
When you turn on the LCD TV set for the first time, the First Installation routine, which makes installation easier, is
activated. Using this routine, you can select the on-screen display language, and automatically search for and store all
the receivable channels.
1
(MAIN POWER)
1 Press the (MAIN POWER)
switch. The “First installation
(Language)” screen with a list of the
languages for the on-screen display
appears.
2
2 Press ]/[ to select the desired
language, and then press OK. The
“First installation (Automatic
search)” screen appears in the
language selected.
First installation
(
Language
)
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
OK
M
Back
E
End
SUBTITLE
SUBTITLE
HOLD
HOLD
W
W
E
E
ID
ID
SUBPAGE
SUBPAGE
MENU
OK
CH
CH
TEXT
TEXT
T
T
T
REVEAL
REVEAL
TV/VIDEO
TV/VIDEO
Note:
• You can change the on-screen
display language after the First
Installation routine by selecting
“Language” on the TV menu (see
pages 13 and 14).
3 Press ]/[ to select the desired
ROTATE
ROTATE
3
adjustment item, and then press
OK
END
END
E
E
MENUSOUND
MENUSOUND
M
M
END
]/[
OK. Then press </> to select the
desired item.
4
4 Press ]/[ to select “Start search”.
< />
First installation
(
Automatic search
)
Country [Germany]
Colour system [ PAL]
Sound system [ B/G]
Start search
OK
First installation
(
Automatic search
M
Back
E
End
)
Country [Germany]
Colour system [ PAL]
Sound system [ B/G]
Start search
5
5 Press OK to begin the automatic
programme search.
OK
Start search
759.25MHz Auto-B/G
0
8 SHARP
1 E 2 9
2 E 4 1
3 U 2 11
4 U 4 12
5 E 5 13
6 E 8 14
7 E1 15
M
Back
0
0
0
0
0
0
0
0
M
Cancel
E
End
Note:
Notes:
When the search is completed,
the new programmes found are
displayed in yellow on the
programme list.
6
6 Press END to exit.
Start search
Search is completed
0
8 SHARP
1 E 2 9
2 E 4 1
3 U 2 11
4 U 4 12
5 E 5 13
6 E 8 14
7 E1 15
0
0
0
0
0
0
0
0
E
End
• AV1 is automatically switched to, when “First installation” is selected. If you selected “First installation”, and want to return to the
previous screen, press Flashback ( ).
7
Loading...