Page 1
Preparation
Installing Batteries in the Remote Control
Before using the LCD TV set for the first time, install the two R-03 (“AAA” size, UM/SUM-4) batteries supplied in the remote
control. When the batteries become depleted and the remote control fails to operate, replace the batteries with new R-03
(“AAA” size, UM/SUM-4) batteries.
1 Open the battery cover. 2 Insert two R-03 (“AAA” size,
UM/SUM-4) batteries.
■ Slide the cover while
pressing the ([) part.
■ Position the positive and
negative ends of the
batteries as indicated in
the compartment.
3 Replace the battery cover.
■ Engaging the lower
claw with the remote
control, close the
cover.
Caution!
Precautions regarding batteries
■ Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) indications.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old
batteries to leak chemicals.
• Remove batteries as soon as they are depleted. Chemicals that leak from batteries can cause a rash. If chemical
leakage is found, wipe it off with a cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control is not to be used for an extended period of time, remove the batteries from the remote control.
Using Remote Control
■ Use the remote control by pointing it towards the remote sensor
window of the main unit. Objects between the remote control and
sensor window may prevent proper operation.
Remote sensor indicator
Power/Standby indicator
Remote sensor window
Cautions regarding use of remote control
■ Do not expose the remote control to shock. In addition, do not
expose the remote control to liquids, and do not place it in an area
with high humidity.
■ Do not install or place the remote control under direct sunlight. The
heat may cause deformation of the unit.
■ The remote control may not work properly if the remote sensor
window is under direct sunlight or strong lighting. In such a case,
change the angle of the lighting or main unit, or operate the remote
control closer to the remote sensor window.
LC-13B4E(E)#p01_10.p65 03.3.10, 2:52 PM5
5
Page 2
Preparation (Continued)
Connect to the DC input terminal of the product.
Power Connection
(MAIN POWER)
Pull down the
Pull down the
hook to open
the cover.
hook to open
the cover.
1
IN
-
V
A
B
G
R
2
N
-I
V
A
O
E
D
I
-V
S
O
E
ID
V
L
IO
D
U
A
R
R
E
W
O
P
T
U
P
IN
2V
1
C
L
R
D
To POWER INPUT
terminal
Household
power outlet
Plug into an AC outlet.
AC adapter
*
AC cord
* Product shape varies in some countries.
Note:
Note:
• Always turn the
• Unplug the AC adapter from the LCD TV set and power outlet when the LCD TV set is not to be used for a long period of time.
(MAIN POWER) switch of the LCD TV set to OFF when connecting the AC adapter.
Antenna Connection
To enjoy a clearer picture, we recommend that you use an
outdoor antenna. The following is a brief explanation of the
types of connection that are used for coaxial and feeder cables:
(1)If your outdoor antenna uses a 75-ohm coaxial cable,
change this for a new standard DIN45325 (IEC169-2) plug
and plug it into the antenna terminal at the back of TV set
via the antenna cable (not supplied).
(2)If your outdoor antenna uses a 300-ohm twin-lead flat
feeder, change this for a 300-ohm to 75-ohm impedance
converter and plug it into the antenna terminal at the back
of TV set via the antenna cable (not supplied).
75-ohm coaxial cable (round cable)
L
R
G
R
ID
V
-
S
O
E
ID
V
L
O
I
D
U
A
R
O
P
IN
C
D
1
N
-I
V
A
B
2
IN
V
A
O
E
R
E
W
T
U
P
V
2
1
6
LC-13B4E(E)#p01_10.p65 03.3.10, 2:52 PM6
300-ohm twin-lead flat feeder
To antenna
input terminal
(
)
Page 3
Preparation (Continued)
First Installation
When you turn on the LCD TV set for the first time, the First Installation routine, which makes installation easier, is
activated. Using this routine, you can select the on-screen display language, and automatically search for and store all
the receivable channels.
1
LE
LE
IT
IT
T
T
B
B
U
U
S
S
(MAIN POWER)
T
T
E
HT
E
E
ID
X
X
IG
T
T
R
W
B
T
T
T
SUBPAGE
SUBPAGE
R
R
E
E
V
V
HOLD
HOLD
MENU
OK
CH
CH
1 Press the (MAIN POWER)
switch. The “First installation
(Language)” screen with a list of the
languages for the on-screen display
appears.
2
2 Press ]/[ to select the desired
language, and then press OK. The
“First installation (Automatic
search)” screen appears in the
language selected.
Note:
• You can change the on-screen
display language after the First
Installation routine by selecting
“Language” on the TV menu (see
pages 13 and 14).
3 Press ]/[ to select the desired
RO
RO
TA
TA
T
T
E
E
E
E
A
A
L
L
MENUSOUND
MENUSOUND
OK
EN
EN
D
D
E
E
END
]/[
M
M
< / >
3
adjustment item, and then press
OK. Then press </> to select the
desired item.
4
4 Press ]/[ to select “Start search”.
First installation
(
)
Language
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
OK
First installation
(
Automatic search
Country
Colour system [ PAL
Sound system [ I
Start search
OK
First installation
(
Automatic search
Country
Colour system [ PAL
Sound system [ I
Start search
OK
M
Back
E
End
[ UK]
M
Back
[ UK]
M
Back
)
E
End
)
E
End
]
]
]
]
TV/VIDEO
TV/VIDEO
Notes:
Note:
• AV1 is automatically switched to, when “First installation” is selected. If you selected “First installation”, and want to return to the
previous screen, press Flashback (
LC-13B4E(E)#p01_10.p65 03.3.10, 2:52 PM7
5
5 Press OK to begin the automatic
programme search.
When the search is completed,
the new programmes found are
displayed in yellow on the
programme list.
6
6 Press END to exit.
).
Start search
42.25MHz PAL-I
0
8 16
1 9 17
2 1 18
3 11 19
4 12 2
5 13 21
6 14 22
7 15 23
Start search
Search is completed
8 16
0
1
S
2
S 8
3
S
1 11 19
4
S
11 12 2
E
5
E
6
E
7
OK
0
0
M
Cancel
6 9 17
0
0
1 18
0
0
3 13 21
0
5 14 22
0
6 15 23
0
0
E
End
7
Loading...